Improve mainboard.c comments for DBM690T and Pistachio. Fix reference to documentation. Use __FUNCTION__ instead of hardcoding function names in printk messages.
No functional changes.
I'm slowly getting to the point where adding another RS690 board is really easy and needs almost no changes to the existing target.
Signed-off-by: Carl-Daniel Hailfinger c-d.hailfinger.devel.2006@gmx.net
Index: LinuxBIOSv2-asus_m2a-vm/src/mainboard/amd/pistachio/mainboard.c =================================================================== --- LinuxBIOSv2-asus_m2a-vm/src/mainboard/amd/pistachio/mainboard.c (Revision 3936) +++ LinuxBIOSv2-asus_m2a-vm/src/mainboard/amd/pistachio/mainboard.c (Arbeitskopie) @@ -49,11 +49,11 @@ * It has a pin named LOW_POWER to enable it into LOW POWER state. * In order to run NIC, we should let it out of Low power state. This pin is * controlled by GPM8. -* RPR4.2.3 GPM as GPIO +* RRG4.2.3 GPM as GPIO * GPM pins can be used as GPIO. The GPM I/O functions is controlled by three registers: * I/O C50, C51, C52, PM I/O94, 95, 96. -* RPR4.2.3.1 GPM pins as Input -* RPR4.2.3.2 GPM pins as Output +* RRG4.2.3.1 GPM pins as Input +* RRG4.2.3.2 GPM pins as Output * The R77 (on BRASS) / R81 (on Bronze) is not load! * So NIC can work whether this function runs. ********************************************************/ @@ -191,18 +191,18 @@ sm_dev->path.u.pci.devfn, 0x41, byte);
/* set GPM5 as input */ - /* step1: set index register 0C50h to 13h (miscellaneous control) */ + /* set index register 0C50h to 13h (miscellaneous control) */ outb(0x13, 0xC50); /* CMIndex */ - /* step2: set CM data register 0C51h bits [7:6] to 01b to set Input/Out control */ + /* set CM data register 0C51h bits [7:6] to 01b to set Input/Out control */ byte = inb(0xC51); /* CMData */ byte &= 0x3f; byte |= 1 << 6; outb(byte, 0xC51); - /* step3: set GPM port 0C52h appropriate bits to 1 to tri-state the GPM port */ + /* set GPM port 0C52h bit 5 to 1 to tri-state the GPM port */ byte = inb(0xc52); /* GpmPort */ byte |= 1 << 5; outb(byte, 0xc52); - /* step4: set CM data register 0C51h bits [7:6] to 00b to set GPM port for read */ + /* set CM data register 0C51h bits [7:6] to 00b to set GPM port for read */ byte = inb(0xc51); byte &= 0x3f; outb(byte, 0xc51); @@ -282,14 +282,14 @@ /* TOP_MEM: the top of DRAM below 4G */ msr = rdmsr(TOP_MEM); printk_info - ("pistachio_enable, TOP MEM: msr.lo = 0x%08x, msr.hi = 0x%08x\n", - msr.lo, msr.hi); + ("%s, TOP MEM: msr.lo = 0x%08x, msr.hi = 0x%08x\n", + __FUNCTION__, msr.lo, msr.hi);
/* TOP_MEM2: the top of DRAM above 4G */ msr2 = rdmsr(TOP_MEM2); printk_info - ("pistachio_enable, TOP MEM2: msr2.lo = 0x%08x, msr2.hi = 0x%08x\n", - msr2.lo, msr2.hi); + ("%s, TOP MEM2: msr2.lo = 0x%08x, msr2.hi = 0x%08x\n", + __FUNCTION__, msr2.lo, msr2.hi);
switch (msr.lo) { case 0x10000000: /* 256M system memory */ @@ -310,8 +310,8 @@ }
uma_memory_start = msr.lo - uma_memory_size; /* TOP_MEM1 */ - printk_info("pistachio_enable: uma size 0x%08x, memory start 0x%08x\n", - uma_memory_size, uma_memory_start); + printk_info("%s: uma size 0x%08x, memory start 0x%08x\n", + __FUNCTION__, uma_memory_size, uma_memory_start);
/* TODO: TOP_MEM2 */ #else Index: LinuxBIOSv2-asus_m2a-vm/src/mainboard/amd/dbm690t/mainboard.c =================================================================== --- LinuxBIOSv2-asus_m2a-vm/src/mainboard/amd/dbm690t/mainboard.c (Revision 3936) +++ LinuxBIOSv2-asus_m2a-vm/src/mainboard/amd/dbm690t/mainboard.c (Arbeitskopie) @@ -49,8 +49,8 @@ /******************************************************** * dbm690t uses a BCM5789 as on-board NIC. * It has a pin named LOW_POWER to enable it into LOW POWER state. -* In order to run NIC, we should let it out of Low power state. This pin -* is controlled by sb600 GPM3. +* In order to run NIC, we should let it out of Low power state. This pin is +* controlled by sb600 GPM3. * RRG4.2.3 GPM as GPIO * GPM pins can be used as GPIO. The GPM I/O functions is controlled by three registers: * I/O C50, C51, C52, PM I/O94, 95, 96. @@ -63,22 +63,27 @@
printk_info("enable_onboard_nic.\n");
- outb(0x13, 0xC50); + /* set index register 0C50h to 13h (miscellaneous control) */ + outb(0x13, 0xC50); /* CMIndex */
+ /* set CM data register 0C51h bits [7:6] to 01b to set Input/Out control */ byte = inb(0xC51); byte &= 0x3F; byte |= 0x40; outb(byte, 0xC51);
+ /* set GPM port 0C52h bit 3 to 0 to enable output for GPM3 */ byte = inb(0xC52); byte &= ~0x8; outb(byte, 0xC52);
+ /* set CM data register 0C51h bits [7:6] to 10b to set Output state control */ byte = inb(0xC51); byte &= 0x3F; byte |= 0x80; /* 7:6=10 */ outb(byte, 0xC51);
+ /* set GPM port 0C52h bit 3 to 0 to output 0 on GPM3 */ byte = inb(0xC52); byte &= ~0x8; outb(byte, 0xC52); @@ -205,14 +210,14 @@ /* TOP_MEM: the top of DRAM below 4G */ msr = rdmsr(TOP_MEM); printk_info - ("dbm690t_enable, TOP MEM: msr.lo = 0x%08x, msr.hi = 0x%08x\n", - msr.lo, msr.hi); + ("%s, TOP MEM: msr.lo = 0x%08x, msr.hi = 0x%08x\n", + __FUNCTION__, msr.lo, msr.hi);
/* TOP_MEM2: the top of DRAM above 4G */ msr2 = rdmsr(TOP_MEM2); printk_info - ("dbm690t_enable, TOP MEM2: msr2.lo = 0x%08x, msr2.hi = 0x%08x\n", - msr2.lo, msr2.hi); + ("%s, TOP MEM2: msr2.lo = 0x%08x, msr2.hi = 0x%08x\n", + __FUNCTION__, msr2.lo, msr2.hi);
switch (msr.lo) { case 0x10000000: /* 256M system memory */ @@ -233,8 +238,8 @@ }
uma_memory_start = msr.lo - uma_memory_size; /* TOP_MEM1 */ - printk_info("dbm690t_enable: uma size 0x%08x, memory start 0x%08x\n", - uma_memory_size, uma_memory_start); + printk_info("%s: uma size 0x%08x, memory start 0x%08x\n", + __FUNCTION__, uma_memory_size, uma_memory_start);
/* TODO: TOP_MEM2 */ #else