Re: [LinuxBIOS] [PATCH] probe_superio: add ITE support (try2)

[todthgie]

i just ran it on my box ..under stock bios (no LB for this board yet )

ubuddie probe_superio # ./probe_superio
No SuperIO chip found at 0x002e
No SuperIO chip found at 0x002e
ITE? SuperIO found at 0x2e: id=0x8705, chipver=0x2
ITE chip
index 20=87
index 21=05
index 22=02
index 23=00
index 24=d9
UART1 is enabled
No SuperIO chip found at 0x004e
No SuperIO chip found at 0x004e
ITE? SuperIO found at 0x4e: id=0x8705, chipver=0x2
ITE chip
index 20=87
index 21=05
index 22=02
index 23=00
index 24=d9
UART1 is enabled

----- Original Message ----- 
From: "Carl-Daniel Hailfinger" 
To: "LinuxBIOS" 
Sent: Thursday, August 23, 2007 22:25
Subject: [LinuxBIOS] [PATCH] probe_superio: add ITE support (try2)
> This adds probing for almost all recent (since 1999) ITE Super I/O chips
> to probe_superio. Not much of the configuration is dumped, however I did
> verify against all ITE datasheets (including those not available any
> more) that the probing was non-destructive.
> More information can be extracted easily, however this needs loads of
> datasheet surfing.
>
> Signed-off-by: Carl-Daniel Hailfinger

--------------------------------------------------------------------------------
> --- LinuxBIOSv2/util/probe_superio/probe_superio.c (Revision 2744)
> +++ LinuxBIOSv2/util/probe_superio/probe_superio.c (Arbeitskopie)
> @@ -3,6 +3,7 @@
> Copyright (C) 2006 Ronald Minnich
> Copyright (C) 2006 coresystems GmbH
> Copyright (C) 2007 Carl-Daniel Hailfinger
> This program is free software; you can redistribute it and/or modify
> it under the terms of the GNU General Public License as published by
>
> @@ -32,11 +33,16 @@
> if we need this.
>
> */
>
> -unsigned char regval(unsigned short port, unsigned short reg) {
> +unsigned char regval(unsigned short port, unsigned char reg) {
>  outb(reg, port);
>  return inb(port+1);
> }
>
> +void regwrite(unsigned short port, unsigned char reg, unsigned char val) 
> {
> outb(reg, port);
> outb(val, port+1);
>
> +}
>
> void
> dump_ns8374(unsigned short port) {
>  printf("Enables: 21=%02x, 22=%02x, 23=%02x, 24=%02x, 26=%02x\n",
> @@ -46,15 +52,13 @@
>  /* check COM1. This is all we care about at present. */
>  printf("COM 1 is Globally %s\n", regval(port,0x26)&8 ? "disabled" : 
> "enabled");
>  /* select com1 */
> outb(0x7, port);
> outb(3, port+1);
> regwrite(port, 0x07, 0x03);
>
> printf("COM 1 is locally %s\n", regval(port, 0x30) & 1 ? "enabled" : 
> "disabled");
>  printf("COM1 60=%02x, 61=%02x, 70=%02x, 71=%02x, 74=%02x, 75=%02x, 
> f0=%02x\n",
>  regval(port, 0x60), regval(port, 0x61), regval(port, 0x70), regval(port, 
> 0x71),
>  regval(port, 0x74), regval(port, 0x75), regval(port, 0xf0));
>  /* select gpio */
> outb(0x7, port);
> outb(7, port+1);
> regwrite(port, 0x07, 0x07);
>
> printf("GPIO is %s\n", regval(port, 0x30) & 1 ? "enabled" : "disabled");
>  printf("GPIO 60=%02x, 61=%02x, 70=%02x, 71=%02x, 74=%02x, 75=%02x, 
> f0=%02x\n",
>  regval(port, 0x60), regval(port, 0x61), regval(port, 0x70), regval(port, 
> 0x71),
> @@ -85,38 +89,33 @@
>  printf("2b=%02x\n", regval(port, 0x2b));
>
> /* select UART 1 */
> outb(0x07, port);
> outb(0x01, port+1);
> regwrite(port, 0x07, 0x01);
>
> printf("UART1 is %s\n", regval(port, 0x30) & 1 ? "enabled" : "disabled");
>  printf("UART1 base=%02x%02x, irq=%02x, mode=%s\n",
>  regval(port, 0x60), regval(port, 0x61), regval(port, 0x70)&0x0f,
>  regval(port, 0xf0)&0x10 ? "RS485":"RS232");
>
> /* select UART 2 */
> outb(0x07, port);
> outb(0x02, port+1);
> regwrite(port, 0x07, 0x02);
>
> printf("UART2 is %s\n", regval(port, 0x30) & 1 ? "enabled" : "disabled");
>  printf("UART2 base=%02x%02x, irq=%02x, mode=%s\n",
>  regval(port, 0x60), regval(port, 0x61), regval(port, 0x70)&0x0f,
>  regval(port, 0xf0)&0x10 ? "RS485":"RS232");
>
> /* select Parport */
> outb(0x07, port);
> outb(0x03, port+1);
> regwrite(port, 0x07, 0x03);
>
> printf("PARPORT is %s\n", regval(port, 0x30) & 1 ? "enabled" : 
> "disabled");
>  printf("PARPORT base=%02x%02x, irq=%02x\n",
>  regval(port, 0x60), regval(port, 0x61), regval(port, 0x70)&0x0f);
>
> /* select hw monitor */
> outb(0x07, port);
> outb(0x04, port+1);
> regwrite(port, 0x07, 0x04);
>
> printf("HW monitor is %s\n", regval(port, 0x30) & 1 ? "enabled" : 
> "disabled");
>  printf("HW monitor base=%02x%02x, irq=%02x\n",
>  regval(port, 0x60), regval(port, 0x61), regval(port, 0x70)&0x0f);
>
> /* select gpio */
> outb(0x07, port);
> outb(0x06, port+1);
> regwrite(port, 0x07, 0x05);
>
> printf("GPIO is %s\n", regval(port, 0x30) & 1 ? "enabled" : "disabled");
>  printf("GPIO 70=%02x, e0=%02x, e1=%02x, e2=%02x, e3=%02x, e4=%02x, 
> e5=%02x\n",
>  regval(port, 0x70), regval(port, 0xe0), regval(port, 0xe1), regval(port, 
> 0xe2),
> @@ -130,7 +129,30 @@
>
> }
>
> +void
> +dump_ite(unsigned short port, unsigned short id)
> +{
>
> int i;
>
> printf ("ITE chip\n");
>
> for (i=0x20; i<=0x24; i++)
>
> printf("index %02x=%02x\n", i, regval(port, i));
>
> switch(id) {
>
> case 0x8702:
>
> case 0x8705:
>
> case 0x8710:
>
> case 0x8712:
>
> case 0x8716:
>
> case 0x8718:
>
> default:
>
> break;
>
> }
>
> /* select UART 1 */
>
> regwrite(port, 0x07, 0x01);
>
> printf("UART1 is %s\n", regval(port, 0x30) & 1 ? "enabled" :
>
> "disabled");
> +}
>
> void
> probe_idregs_simple(unsigned short port){
>  unsigned char id;
> @@ -167,9 +189,10 @@
>
> void
> probe_idregs_fintek(unsigned short port){
> unsigned int vid, did;
> unsigned int vid, did, success = 0;
>
> // Enable configuration sequence (Fintek uses this for example)
> // Older ITE chips have the same enable sequence
>
> outb(0x87, port);
>  outb(0x87, port);
>
> @@ -185,13 +208,10 @@
>  }
>  did = inb(port+1);
> outb(0x21, port);
> did = did|(inb(port+1)<<8);
> did = did|(regval(port, 0x21)<<8);
> outb(0x23, port);
> vid = inb(port+1);
> outb(0x24, port);
> vid = vid|(inb(port+1)<<8);
> vid = regval(port, 0x23);
> vid = vid|(regval(port, 0x24)<<8);
>
> printf("SuperIO found at 0x%02x: vid=0x%04x/did=0x%04x\n", port, vid, 
> did);
>
> @@ -199,23 +219,103 @@
>  return;
>
> // printf("%s\n", familyid[id]);
> switch(did) {
> case 0x1087: // reversed for ITE8710
> success = 1;
> dump_ite(port, ((did & 0xff) << 8) | ((did & 0xff00) >> 8));
> // disable configuration
> regwrite(port, 0x02, 0x02);
> break;
> default:
> break;
> }
>
> switch(vid) {
>  case 0x3419:
> success = 1;
>
> dump_fintek(port, did);
>  break;
>  default:
> printf("no dump for 0x%04x/0x%04x\n", vid, did);
>
> break;
>  }
> if (!success)
> printf("no dump for vid 0x%04x, did 0x%04x\n", vid, did);
> // disable configuration
> // disable configuration (for Fintek, doesn't hurt ITE)
>
> outb(0xaa, port);
> }
>
> void
> +probe_idregs_ite(unsigned short port){
> unsigned int id, chipver;
> // Enable configuration sequence (ITE uses this for newer IT87[012]x)
> // IT871[01] uses 0x87, 0x87 -> fintek detection should handle it
> // IT8761 uses 0x87, 0x61, 0x55, 0x55/0xaa
> // IT86xx series uses different ports
> // IT8661 uses 0x86, 0x61, 0x55/0xaa, 0x55/0xaa and 32 more writes
> // IT8673 uses 0x86, 0x80, 0x55/0xaa, 0x55/0xaa and 32 more writes
> outb(0x87, port);
> outb(0x01, port);
> outb(0x55, port);
> if (port == 0x2e)
> outb(0x55, port);
> else
> outb(0xAA, port);
> // Read Chip ID Byte 1
> id = regval(port, 0x20);
> if (id != 0x87)  {
> if (inb(port) == 0xff )
> printf ("No SuperIO chip found at 0x%04x\n", port);
> else
> printf("probing 0x%04x, failed (0x%02x), data returns 0x%02x\n",
> port, inb(port), inb(port+1));
> return;
> }
> id <<= 8;
> // Read Chip ID Byte 2
> id |= regval(port, 0x21);
> // Read Chip Version, only bit 3..0 for all IT87xx
> chipver = regval(port, 0x22) & 0x0f;
> /* ID Mapping Table
> unknown -> IT8711 (no datasheet)
> unknown -> IT8722 (no datasheet)
> 0x8702 -> IT8702
> 0x8705 -> IT8700 or IT8705
> 0x8710 -> IT8710
> 0x8712 -> IT8712
> 0x8716 -> IT8716 or IT8726 (identical except CPU voltage control)
> 0x8718 -> IT8718
> */
> printf("ITE? SuperIO found at 0x%02x: id=0x%04x, chipver=0x%01x\n",
>    port, id, chipver);
> switch(id) {
> case 0x8702:
> case 0x8705:
> case 0x8710: //pointless, IT8710 has different enable sequence
> case 0x8712:
> case 0x8716:
> case 0x8718:
> dump_ite(port, id);
> break;
> default:
> printf("no dump for id 0x%04x\n", id);
> break;
> }
> // disable configuration
> regwrite(port, 0x02, 0x02);
>
> +}
>
> +void
> probe_superio(unsigned short port) {
>  probe_idregs_simple(port);
>  probe_idregs_fintek(port);
> probe_idregs_ite(port);
>
> }
>
> int

--------------------------------------------------------------------------------
>