Author: linux_junkie Date: 2009-05-02 02:50:58 +0200 (Sat, 02 May 2009) New Revision: 4248
Modified: trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c Log: Trivial fix up to the GPIO's connected to the IP1000 and RM4100, only set ones that are actually connected to something. Signed-off-by: Joseph Smith joe@settoplinux.org Acked-by: Joseph Smith joe@settoplinux.org
Modified: trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c =================================================================== --- trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c 2009-05-01 14:33:19 UTC (rev 4247) +++ trunk/coreboot-v2/src/mainboard/rca/rm4100/gpio.c 2009-05-02 00:50:58 UTC (rev 4248) @@ -1,120 +1,143 @@ -/* - * This file is part of the coreboot project. - * - * Copyright (C) 2008 Joseph Smith joe@smittys.pointclark.net - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ - -#define PME_DEV PNP_DEV(0x2e, 0x0a) -#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */ -#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */ - -/* Early mainboard specific GPIO setup. */ -static void mb_gpio_init(void) -{ - device_t dev; - uint16_t port; - uint32_t set_gpio; - - /* Southbridge GPIOs. */ - /* Set the LPC device statically. */ - dev = PCI_DEV(0x0, 0x1f, 0x0); - - /* Set the value for GPIO base address register and enable GPIO. */ - pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1)); - pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10); - - /* Set GPIO25 to input and drive GPIO23 to high, - * this enables the LAN controller. - */ - udelay(10); - set_gpio = 0x0000ffff; - set_gpio |= 1 << 25; - outl(set_gpio, ICH_IO_BASE_ADDR + 0x04); - - set_gpio = 0x1b3f0000; - set_gpio |= 1 << 23; - outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c); - - /* Super I/O GPIOs. */ - dev = PME_DEV; - port = dev >> 8; - - outb(0x55, port); /* Enter the configuration state. */ - pnp_set_logical_device(dev); - pnp_set_enable(dev, 0); - pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR); - pnp_set_enable(dev, 1); - outl(0x03, PME_IO_BASE_ADDR + 0x1e); /* Force Disk Change */ - outl(0x02, PME_IO_BASE_ADDR + 0x1f); /* Floppy Data Rate */ - outl(0x81, PME_IO_BASE_ADDR + 0x20); /* UART1 FIFO */ - outl(0x00, PME_IO_BASE_ADDR + 0x21); /* UART2 FIFO */ - outl(0x00, PME_IO_BASE_ADDR + 0x22); /* Device Disable */ - outl(0x01, PME_IO_BASE_ADDR + 0x23); /* GP10 */ - outl(0x01, PME_IO_BASE_ADDR + 0x24); /* GP11 */ - outl(0x01, PME_IO_BASE_ADDR + 0x25); /* GP12 */ - outl(0x01, PME_IO_BASE_ADDR + 0x26); /* GP13 */ - outl(0x01, PME_IO_BASE_ADDR + 0x27); /* GP14 */ - outl(0x01, PME_IO_BASE_ADDR + 0x28); /* GP15 */ - outl(0x01, PME_IO_BASE_ADDR + 0x29); /* GP16 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2a); /* GP17 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2b); /* GP20 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2c); /* GP21 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2d); /* GP22 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2f); /* GP24 */ - outl(0x01, PME_IO_BASE_ADDR + 0x30); /* GP25 */ - outl(0x01, PME_IO_BASE_ADDR + 0x31); /* GP26 */ - outl(0x01, PME_IO_BASE_ADDR + 0x32); /* GP27 */ - outl(0x05, PME_IO_BASE_ADDR + 0x33); /* GP30 */ - outl(0x05, PME_IO_BASE_ADDR + 0x34); /* GP31 */ - outl(0x00, PME_IO_BASE_ADDR + 0x35); /* GP32 */ - outl(0x00, PME_IO_BASE_ADDR + 0x36); /* GP33 */ - outl(0x00, PME_IO_BASE_ADDR + 0x37); /* GP34 */ - outl(0x04, PME_IO_BASE_ADDR + 0x38); /* GP35 */ - outl(0x01, PME_IO_BASE_ADDR + 0x39); /* GP36 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3a); /* GP37 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3b); /* GP40 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3c); /* GP41 */ - outl(0x86, PME_IO_BASE_ADDR + 0x3d); /* GP42 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3e); /* GP43 */ - outl(0x05, PME_IO_BASE_ADDR + 0x3f); /* GP50 */ - outl(0x05, PME_IO_BASE_ADDR + 0x40); /* GP51 */ - outl(0x05, PME_IO_BASE_ADDR + 0x41); /* GP52 */ - outl(0x04, PME_IO_BASE_ADDR + 0x42); /* GP53 */ - outl(0x05, PME_IO_BASE_ADDR + 0x43); /* GP54 */ - outl(0x04, PME_IO_BASE_ADDR + 0x44); /* GP55 */ - outl(0x05, PME_IO_BASE_ADDR + 0x45); /* GP56 */ - outl(0x04, PME_IO_BASE_ADDR + 0x46); /* GP57 */ - outl(0x01, PME_IO_BASE_ADDR + 0x47); /* GP58 */ - outl(0x01, PME_IO_BASE_ADDR + 0x48); /* GP59 */ - outl(0x00, PME_IO_BASE_ADDR + 0x4b); /* GP1 */ - outl(0x04, PME_IO_BASE_ADDR + 0x4c); /* GP2 */ - outl(0xc0, PME_IO_BASE_ADDR + 0x4d); /* GP3 */ - outl(0x00, PME_IO_BASE_ADDR + 0x4e); /* GP4 */ - outl(0x07, PME_IO_BASE_ADDR + 0x4f); /* GP5 */ - outl(0x00, PME_IO_BASE_ADDR + 0x50); /* GP6 */ - outl(0x00, PME_IO_BASE_ADDR + 0x56); /* FAN1 */ - outl(0x00, PME_IO_BASE_ADDR + 0x57); /* FAN2 */ - outl(0x50, PME_IO_BASE_ADDR + 0x58); /* Fan Control */ - outl(0xff, PME_IO_BASE_ADDR + 0x59); /* Fan1 Tachometer */ - outl(0xff, PME_IO_BASE_ADDR + 0x5a); /* Fan2 Tachometer */ - outl(0x00, PME_IO_BASE_ADDR + 0x5b); /* Fan1 Preload */ - outl(0x00, PME_IO_BASE_ADDR + 0x5c); /* Fan2 Preload */ - outl(0x00, PME_IO_BASE_ADDR + 0x5d); /* LED1 */ - outl(0x00, PME_IO_BASE_ADDR + 0x5e); /* LED2 */ - outl(0x00, PME_IO_BASE_ADDR + 0x5f); /* Keyboard Scan Code */ - outb(0xaa, port); /* Exit the configuration state. */ -} +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 Joseph Smith joe@settoplinux.org + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#define PME_DEV PNP_DEV(0x2e, 0x0a) +#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */ +#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */ + +/* Early mainboard specific GPIO setup. */ +static void mb_gpio_init(void) +{ + device_t dev; + uint16_t port; + uint32_t set_gpio; + + /* Southbridge GPIOs. */ + /* Set the LPC device statically. */ + dev = PCI_DEV(0x0, 0x1f, 0x0); + + /* Set the value for GPIO base address register and enable GPIO. */ + pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1)); + pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10); + + /* Set GPIO23 to high, this enables the LAN controller. */ + udelay(10); + set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c); + set_gpio |= 1 << 23; + outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c); + + /* Super I/O GPIOs. */ + dev = PME_DEV; + port = dev >> 8; + + /* Enter the configuration state. */ + outb(0x55, port); + pnp_set_logical_device(dev); + pnp_set_enable(dev, 0); + pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR); + pnp_set_enable(dev, 1); + + /* GP21 - LED_RED */ + outl(0x01, PME_IO_BASE_ADDR + 0x2c); + + /* GP30 - FAN2_TACH */ + outl(0x05, PME_IO_BASE_ADDR + 0x33); + + /* GP31 - FAN1_TACH */ + outl(0x05, PME_IO_BASE_ADDR + 0x34); + + /* GP32 - FAN2_CTRL */ + outl(0x04, PME_IO_BASE_ADDR + 0x35); + + /* GP33 - FAN1_CTRL */ + outl(0x04, PME_IO_BASE_ADDR + 0x36); + + /* GP34 - AUD_MUTE_OUT_R */ + outl(0x00, PME_IO_BASE_ADDR + 0x37); + + /* GP36 - KBRST */ + outl(0x00, PME_IO_BASE_ADDR + 0x39); + + /* GP37 - A20GATE */ + outl(0x00, PME_IO_BASE_ADDR + 0x3a); + + /* GP42 - GPIO_PME_OUT */ + outl(0x00, PME_IO_BASE_ADDR + 0x3d); + + /* GP50 - SER2_RI */ + outl(0x05, PME_IO_BASE_ADDR + 0x3f); + + /* GP51 - SER2_DCD */ + outl(0x05, PME_IO_BASE_ADDR + 0x40); + + /* GP52 - SER2_RX */ + outl(0x05, PME_IO_BASE_ADDR + 0x41); + + /* GP53 - SER2_TX */ + outl(0x04, PME_IO_BASE_ADDR + 0x42); + + /* GP55 - SER2_RTS */ + outl(0x04, PME_IO_BASE_ADDR + 0x44); + + /* GP56 - SER2_CTS */ + outl(0x05, PME_IO_BASE_ADDR + 0x45); + + /* GP57 - SER2_DTR */ + outl(0x04, PME_IO_BASE_ADDR + 0x46); + + /* GP60 - LED_GREEN */ + outl(0x01, PME_IO_BASE_ADDR + 0x47); + + /* GP61 - LED_YELLOW */ + outl(0x01, PME_IO_BASE_ADDR + 0x48); + + /* GP3 */ + outl(0xc0, PME_IO_BASE_ADDR + 0x4d); + + /* GP4 */ + outl(0x04, PME_IO_BASE_ADDR + 0x4e); + + /* FAN1 */ + outl(0x01, PME_IO_BASE_ADDR + 0x56); + + /* FAN2 */ + outl(0x01, PME_IO_BASE_ADDR + 0x57); + + /* Fan Control */ + outl(0x50, PME_IO_BASE_ADDR + 0x58); + + /* Fan1 Tachometer */ + outl(0xff, PME_IO_BASE_ADDR + 0x59); + + /* Fan2 Tachometer */ + outl(0xff, PME_IO_BASE_ADDR + 0x5a); + + /* LED1 */ + outl(0x00, PME_IO_BASE_ADDR + 0x5d); + + /* LED2 */ + outl(0x00, PME_IO_BASE_ADDR + 0x5e); + + /* Keyboard Scan Code */ + outl(0x00, PME_IO_BASE_ADDR + 0x5f); + + /* Exit the configuration state. */ + outb(0xaa, port); +}
Modified: trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c =================================================================== --- trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c 2009-05-01 14:33:19 UTC (rev 4247) +++ trunk/coreboot-v2/src/mainboard/thomson/ip1000/gpio.c 2009-05-02 00:50:58 UTC (rev 4248) @@ -1,120 +1,143 @@ -/* - * This file is part of the coreboot project. - * - * Copyright (C) 2008 Joseph Smith joe@settoplinux.org - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA - */ - -#define PME_DEV PNP_DEV(0x2e, 0x0a) -#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */ -#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */ - -/* Early mainboard specific GPIO setup. */ -static void mb_gpio_init(void) -{ - device_t dev; - uint16_t port; - uint32_t set_gpio; - - /* Southbridge GPIOs. */ - /* Set the LPC device statically. */ - dev = PCI_DEV(0x0, 0x1f, 0x0); - - /* Set the value for GPIO base address register and enable GPIO. */ - pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1)); - pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10); - - /* Set GPIO25 to input and drive GPIO23 to high, - * this enables the LAN controller. - */ - udelay(10); - set_gpio = 0x0000ffff; - set_gpio |= 1 << 25; - outl(set_gpio, ICH_IO_BASE_ADDR + 0x04); - - set_gpio = 0x1b3f0000; - set_gpio |= 1 << 23; - outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c); - - /* Super I/O GPIOs. */ - dev = PME_DEV; - port = dev >> 8; - - outb(0x55, port); /* Enter the configuration state. */ - pnp_set_logical_device(dev); - pnp_set_enable(dev, 0); - pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR); - pnp_set_enable(dev, 1); - outl(0x03, PME_IO_BASE_ADDR + 0x1e); /* Force Disk Change */ - outl(0x02, PME_IO_BASE_ADDR + 0x1f); /* Floppy Data Rate */ - outl(0x81, PME_IO_BASE_ADDR + 0x20); /* UART1 FIFO */ - outl(0x81, PME_IO_BASE_ADDR + 0x21); /* UART2 FIFO */ - outl(0x00, PME_IO_BASE_ADDR + 0x22); /* Device Disable */ - outl(0x01, PME_IO_BASE_ADDR + 0x23); /* GP10 */ - outl(0x01, PME_IO_BASE_ADDR + 0x24); /* GP11 */ - outl(0x01, PME_IO_BASE_ADDR + 0x25); /* GP12 */ - outl(0x01, PME_IO_BASE_ADDR + 0x26); /* GP13 */ - outl(0x01, PME_IO_BASE_ADDR + 0x27); /* GP14 */ - outl(0x01, PME_IO_BASE_ADDR + 0x28); /* GP15 */ - outl(0x01, PME_IO_BASE_ADDR + 0x29); /* GP16 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2a); /* GP17 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2b); /* GP20 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2c); /* GP21 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2d); /* GP22 */ - outl(0x01, PME_IO_BASE_ADDR + 0x2f); /* GP24 */ - outl(0x01, PME_IO_BASE_ADDR + 0x30); /* GP25 */ - outl(0x01, PME_IO_BASE_ADDR + 0x31); /* GP26 */ - outl(0x01, PME_IO_BASE_ADDR + 0x32); /* GP27 */ - outl(0x05, PME_IO_BASE_ADDR + 0x33); /* GP30 */ - outl(0x05, PME_IO_BASE_ADDR + 0x34); /* GP31 */ - outl(0x84, PME_IO_BASE_ADDR + 0x35); /* GP32 */ - outl(0x84, PME_IO_BASE_ADDR + 0x36); /* GP33 */ - outl(0x00, PME_IO_BASE_ADDR + 0x37); /* GP34 */ - outl(0x04, PME_IO_BASE_ADDR + 0x38); /* GP35 */ - outl(0x01, PME_IO_BASE_ADDR + 0x39); /* GP36 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3a); /* GP37 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3b); /* GP40 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3c); /* GP41 */ - outl(0x86, PME_IO_BASE_ADDR + 0x3d); /* GP42 */ - outl(0x01, PME_IO_BASE_ADDR + 0x3e); /* GP43 */ - outl(0x05, PME_IO_BASE_ADDR + 0x3f); /* GP50 */ - outl(0x05, PME_IO_BASE_ADDR + 0x40); /* GP51 */ - outl(0x05, PME_IO_BASE_ADDR + 0x41); /* GP52 */ - outl(0x04, PME_IO_BASE_ADDR + 0x42); /* GP53 */ - outl(0x05, PME_IO_BASE_ADDR + 0x43); /* GP54 */ - outl(0x04, PME_IO_BASE_ADDR + 0x44); /* GP55 */ - outl(0x05, PME_IO_BASE_ADDR + 0x45); /* GP56 */ - outl(0x04, PME_IO_BASE_ADDR + 0x46); /* GP57 */ - outl(0x01, PME_IO_BASE_ADDR + 0x47); /* GP58 */ - outl(0x01, PME_IO_BASE_ADDR + 0x48); /* GP59 */ - outl(0x00, PME_IO_BASE_ADDR + 0x4b); /* GP1 */ - outl(0x04, PME_IO_BASE_ADDR + 0x4c); /* GP2 */ - outl(0xc0, PME_IO_BASE_ADDR + 0x4d); /* GP3 */ - outl(0x00, PME_IO_BASE_ADDR + 0x4e); /* GP4 */ - outl(0x04, PME_IO_BASE_ADDR + 0x4f); /* GP5 */ - outl(0x00, PME_IO_BASE_ADDR + 0x50); /* GP6 */ - outl(0x01, PME_IO_BASE_ADDR + 0x56); /* FAN1 */ - outl(0x01, PME_IO_BASE_ADDR + 0x57); /* FAN2 */ - outl(0x58, PME_IO_BASE_ADDR + 0x58); /* Fan Control */ - outl(0xff, PME_IO_BASE_ADDR + 0x59); /* Fan1 Tachometer */ - outl(0x50, PME_IO_BASE_ADDR + 0x5a); /* Fan2 Tachometer */ - outl(0x00, PME_IO_BASE_ADDR + 0x5b); /* Fan1 Preload */ - outl(0x00, PME_IO_BASE_ADDR + 0x5c); /* Fan2 Preload */ - outl(0x00, PME_IO_BASE_ADDR + 0x5d); /* LED1 */ - outl(0x00, PME_IO_BASE_ADDR + 0x5e); /* LED2 */ - outl(0x00, PME_IO_BASE_ADDR + 0x5f); /* Keyboard Scan Code */ - outb(0xaa, port); /* Exit the configuration state. */ -} +/* + * This file is part of the coreboot project. + * + * Copyright (C) 2008 Joseph Smith joe@settoplinux.org + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#define PME_DEV PNP_DEV(0x2e, 0x0a) +#define PME_IO_BASE_ADDR 0x800 /* Runtime register base address */ +#define ICH_IO_BASE_ADDR 0x00000500 /* GPIO base address register */ + +/* Early mainboard specific GPIO setup. */ +static void mb_gpio_init(void) +{ + device_t dev; + uint16_t port; + uint32_t set_gpio; + + /* Southbridge GPIOs. */ + /* Set the LPC device statically. */ + dev = PCI_DEV(0x0, 0x1f, 0x0); + + /* Set the value for GPIO base address register and enable GPIO. */ + pci_write_config32(dev, GPIO_BASE_ICH0_5, (ICH_IO_BASE_ADDR | 1)); + pci_write_config8(dev, GPIO_CNTL_ICH0_5, 0x10); + + /* Set GPIO23 to high, this enables the LAN controller. */ + udelay(10); + set_gpio = inl(ICH_IO_BASE_ADDR + 0x0c); + set_gpio |= 1 << 23; + outl(set_gpio, ICH_IO_BASE_ADDR + 0x0c); + + /* Super I/O GPIOs. */ + dev = PME_DEV; + port = dev >> 8; + + /* Enter the configuration state. */ + outb(0x55, port); + pnp_set_logical_device(dev); + pnp_set_enable(dev, 0); + pnp_set_iobase(dev, PNP_IDX_IO0, PME_IO_BASE_ADDR); + pnp_set_enable(dev, 1); + + /* GP21 - LED_RED */ + outl(0x01, PME_IO_BASE_ADDR + 0x2c); + + /* GP30 - FAN2_TACH */ + outl(0x05, PME_IO_BASE_ADDR + 0x33); + + /* GP31 - FAN1_TACH */ + outl(0x05, PME_IO_BASE_ADDR + 0x34); + + /* GP32 - FAN2_CTRL */ + outl(0x04, PME_IO_BASE_ADDR + 0x35); + + /* GP33 - FAN1_CTRL */ + outl(0x04, PME_IO_BASE_ADDR + 0x36); + + /* GP34 - AUD_MUTE_OUT_R */ + outl(0x00, PME_IO_BASE_ADDR + 0x37); + + /* GP36 - KBRST */ + outl(0x00, PME_IO_BASE_ADDR + 0x39); + + /* GP37 - A20GATE */ + outl(0x00, PME_IO_BASE_ADDR + 0x3a); + + /* GP42 - GPIO_PME_OUT */ + outl(0x00, PME_IO_BASE_ADDR + 0x3d); + + /* GP50 - SER2_RI */ + outl(0x05, PME_IO_BASE_ADDR + 0x3f); + + /* GP51 - SER2_DCD */ + outl(0x05, PME_IO_BASE_ADDR + 0x40); + + /* GP52 - SER2_RX */ + outl(0x05, PME_IO_BASE_ADDR + 0x41); + + /* GP53 - SER2_TX */ + outl(0x04, PME_IO_BASE_ADDR + 0x42); + + /* GP55 - SER2_RTS */ + outl(0x04, PME_IO_BASE_ADDR + 0x44); + + /* GP56 - SER2_CTS */ + outl(0x05, PME_IO_BASE_ADDR + 0x45); + + /* GP57 - SER2_DTR */ + outl(0x04, PME_IO_BASE_ADDR + 0x46); + + /* GP60 - LED_GREEN */ + outl(0x01, PME_IO_BASE_ADDR + 0x47); + + /* GP61 - LED_YELLOW */ + outl(0x01, PME_IO_BASE_ADDR + 0x48); + + /* GP3 */ + outl(0xc0, PME_IO_BASE_ADDR + 0x4d); + + /* GP4 */ + outl(0x04, PME_IO_BASE_ADDR + 0x4e); + + /* FAN1 */ + outl(0x01, PME_IO_BASE_ADDR + 0x56); + + /* FAN2 */ + outl(0x01, PME_IO_BASE_ADDR + 0x57); + + /* Fan Control */ + outl(0x50, PME_IO_BASE_ADDR + 0x58); + + /* Fan1 Tachometer */ + outl(0xff, PME_IO_BASE_ADDR + 0x59); + + /* Fan2 Tachometer */ + outl(0xff, PME_IO_BASE_ADDR + 0x5a); + + /* LED1 */ + outl(0x00, PME_IO_BASE_ADDR + 0x5d); + + /* LED2 */ + outl(0x00, PME_IO_BASE_ADDR + 0x5e); + + /* Keyboard Scan Code */ + outl(0x00, PME_IO_BASE_ADDR + 0x5f); + + /* Exit the configuration state. */ + outb(0xaa, port); +}