On 12.12.2008 06:35, Bao, Zheng wrote:
It is great to remind me that.
I knew this issue when I did the 690 code. The board I worked with seemed to support just 800Mhz HT link, which doesn't need any more setting when HT is set up. Then I ignore this. Then I had to move on.
As a matter of fact, both 600Mhz and 1Ghz have their own specific setting. I thought rs690_htinit should be removed from rs690_early_setup() and called after optimize_link_incoherent_ht().
Zheng (Joe)
-----Original Message----- From: coreboot-bounces@coreboot.org [mailto:coreboot-bounces@coreboot.org] On Behalf Of Carl-Daniel Hailfinger Sent: Friday, December 12, 2008 12:25 PM To: Coreboot Subject: [coreboot] RS690 HT init
Hi,
it seems that rs690_htinit() does nothing (it only prints some data). Is that intentional?
The RS690 chipset has a problem where it will not work with 1 GHz HT speed unless NB_CFG_Q_F1000_800 bit 0 is set. I think we could add code for this to rs690_htinit().
Handle RS690 quirks for 1 GHz noncoherent HyperTransport.
Tested, works on my Asus M2A-VM with an 1 GHz HT capable processor.
Signed-off-by: Carl-Daniel Hailfinger c-d.hailfinger.devel.2006@gmx.net
Index: southbridge/amd/rs690/rs690_early_setup.c =================================================================== --- southbridge/amd/rs690/rs690_early_setup.c (Revision 3837) +++ southbridge/amd/rs690/rs690_early_setup.c (Arbeitskopie) @@ -2,6 +2,7 @@ * This file is part of the coreboot project. * * Copyright (C) 2008 Advanced Micro Devices, Inc. + * Copyright (C) 2008 Carl-Daniel Hailfinger * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -175,8 +176,9 @@ /* * About HT, it has been done in enumerate_ht_chain(). */ - device_t k8_f0; + device_t k8_f0, rs690_f0; u32 reg; + u8 reg8; u8 k8_ht_freq;
k8_f0 = PCI_DEV(0, 0x18, 0); @@ -195,7 +197,22 @@ ************************/ reg = pci_read_config32(k8_f0, 0x88); k8_ht_freq = (reg & 0xf00) >> 8; - printk_info("rs690_ht_init k8_ht_freq=%x.\n", k8_ht_freq); + printk_spew("rs690_htinit k8_ht_freq=%x.\n", k8_ht_freq); + rs690_f0 = PCI_DEV(0, 0, 0); + reg8 = pci_read_config8(rs690_f0, 0x9c); + printk_spew("rs690_htinit NB_CFG_Q_F1000_800=%x\n", reg8); + /* For 1000 MHz HT, NB_CFG_Q_F1000_800 bit 0 MUST be set. + * For any other HT frequency, NB_CFG_Q_F1000_800 bit 0 MUST NOT be set. + */ + if (((k8_ht_freq == 0x6) || (k8_ht_freq == 0xf)) && (!(reg8 & 0x1))) { + printk_info("rs690_htinit setting bit 0 in NB_CFG_Q_F1000_800 to use 1 GHz HT\n"); + reg8 |= 0x1; + pci_write_config8(rs690_f0, 0x9c, reg8); + } else if ((k8_ht_freq != 0x6) && (k8_ht_freq != 0xf) && (reg8 & 0x1)) { + printk_info("rs690_htinit clearing bit 0 in NB_CFG_Q_F1000_800 to not use 1 GHz HT\n"); + reg8 &= ~0x1; + pci_write_config8(rs690_f0, 0x9c, reg8); + } }
/******************************************************* @@ -462,7 +479,6 @@ break; }
- rs690_htinit(); k8_optimization(); rs690_por_init(nb_dev); } Index: mainboard/amd/dbm690t/cache_as_ram_auto.c =================================================================== --- mainboard/amd/dbm690t/cache_as_ram_auto.c (Revision 3837) +++ mainboard/amd/dbm690t/cache_as_ram_auto.c (Arbeitskopie) @@ -210,6 +210,7 @@
needs_reset = optimize_link_coherent_ht(); needs_reset |= optimize_link_incoherent_ht(sysinfo); + rs690_htinit(); printk_debug("needs_reset=0x%x\n", needs_reset);
Index: mainboard/amd/pistachio/cache_as_ram_auto.c =================================================================== --- mainboard/amd/pistachio/cache_as_ram_auto.c (Revision 3837) +++ mainboard/amd/pistachio/cache_as_ram_auto.c (Arbeitskopie) @@ -213,6 +213,7 @@
needs_reset = optimize_link_coherent_ht(); needs_reset |= optimize_link_incoherent_ht(sysinfo); + rs690_htinit(); printk_debug("needs_reset=0x%x\n", needs_reset);
post_code(0x06);