Author: zbao Date: Sat Oct 9 09:18:50 2010 New Revision: 5928 URL: https://tracker.coreboot.org/trac/coreboot/changeset/5928
Log: Trivial. Spell checking.
Signed-off-by: Zheng Bao zheng.bao@amd.com Acked-by: Zheng Bao zheng.bao@amd.com
Modified: trunk/src/northbridge/amd/amdmct/mct/mctecc_d.c trunk/src/northbridge/amd/amdmct/mct/mctmtr_d.c trunk/src/northbridge/amd/amdmct/mct_ddr3/mctecc_d.c trunk/src/northbridge/amd/amdmct/mct_ddr3/mctmtr_d.c trunk/src/northbridge/amd/amdmct/mct_ddr3/mhwlc_d.c trunk/src/northbridge/amd/amdmct/mct_ddr3/mutilc_d.c trunk/src/northbridge/amd/amdmct/mct_ddr3/mwlc_d.h
Modified: trunk/src/northbridge/amd/amdmct/mct/mctecc_d.c ============================================================================== --- trunk/src/northbridge/amd/amdmct/mct/mctecc_d.c Sat Oct 9 04:31:10 2010 (r5927) +++ trunk/src/northbridge/amd/amdmct/mct/mctecc_d.c Sat Oct 9 09:18:50 2010 (r5928) @@ -61,7 +61,7 @@ * guarantee that the NB scrubs the entire dram on its node. Do do this, we * simply sample the scrub ADDR once, for an initial value, then we sample and poll until the polled value of scrub ADDR * has wrapped around at least once: Scrub ADDRi+1 < Scrub ADDRi. Since we let all - * Nodes run in parallel, we need to gaurantee that all nodes have wrapped. To do + * Nodes run in parallel, we need to guarantee that all nodes have wrapped. To do * this efficiently, we need only to sample one of the nodes, the node with the * largest ammount of dram populated is the one which will take the longest amount * of time (the scrub rate is set to max, the same rate, on all nodes). So,
Modified: trunk/src/northbridge/amd/amdmct/mct/mctmtr_d.c ============================================================================== --- trunk/src/northbridge/amd/amdmct/mct/mctmtr_d.c Sat Oct 9 04:31:10 2010 (r5927) +++ trunk/src/northbridge/amd/amdmct/mct/mctmtr_d.c Sat Oct 9 09:18:50 2010 (r5928) @@ -38,7 +38,7 @@ u32 lo, hi;
/* Set temporary top of memory from Node structure data. - * Adjust temp top of memory down to accomodate 32-bit IO space. + * Adjust temp top of memory down to accommodate 32-bit IO space. * Bottom40bIO=top of memory, right justified 8 bits * (defines dram versus IO space type) * Bottom32bIO=sub 4GB top of memory, right justified 8 bits @@ -151,7 +151,7 @@ * 2. Each range must be naturally aligned (Base is same as size) * * There are two code paths: the ascending path and descending path - * (analogous to bsf and bsr), where the next limit is a funtion of the + * (analogous to bsf and bsr), where the next limit is a function of the * next set bit in a forward or backward sequence of bits (as a function * of the Limit). We start with the ascending path, to ensure that * regions are naturally aligned, then we switch to the descending path @@ -219,7 +219,7 @@ u32 lo, hi;
/*====================================================================== - * Adjust temp top of memory down to accomodate UMA memory start + * Adjust temp top of memory down to accommodate UMA memory start *======================================================================*/ /* Bottom32bIO=sub 4GB top of memory, right justified 8 bits * (defines dram versus IO space type)
Modified: trunk/src/northbridge/amd/amdmct/mct_ddr3/mctecc_d.c ============================================================================== --- trunk/src/northbridge/amd/amdmct/mct_ddr3/mctecc_d.c Sat Oct 9 04:31:10 2010 (r5927) +++ trunk/src/northbridge/amd/amdmct/mct_ddr3/mctecc_d.c Sat Oct 9 09:18:50 2010 (r5928) @@ -56,7 +56,7 @@ * guarantee that the NB scrubs the entire dram on its node. Do do this, we * simply sample the scrub ADDR once, for an initial value, then we sample and poll until the polled value of scrub ADDR * has wrapped around at least once: Scrub ADDRi+1 < Scrub ADDRi. Since we let all - * Nodes run in parallel, we need to gaurantee that all nodes have wrapped. To do + * Nodes run in parallel, we need to guarantee that all nodes have wrapped. To do * this efficiently, we need only to sample one of the nodes, the node with the * largest ammount of dram populated is the one which will take the longest amount * of time (the scrub rate is set to max, the same rate, on all nodes). So,
Modified: trunk/src/northbridge/amd/amdmct/mct_ddr3/mctmtr_d.c ============================================================================== --- trunk/src/northbridge/amd/amdmct/mct_ddr3/mctmtr_d.c Sat Oct 9 04:31:10 2010 (r5927) +++ trunk/src/northbridge/amd/amdmct/mct_ddr3/mctmtr_d.c Sat Oct 9 09:18:50 2010 (r5928) @@ -36,7 +36,7 @@ u32 lo, hi;
/* Set temporary top of memory from Node structure data. - * Adjust temp top of memory down to accomodate 32-bit IO space. + * Adjust temp top of memory down to accommodate 32-bit IO space. * Bottom40bIO=top of memory, right justified 8 bits * (defines dram versus IO space type) * Bottom32bIO=sub 4GB top of memory, right justified 8 bits @@ -145,7 +145,7 @@ * 2. Each range must be naturally aligned (Base is same as size) * * There are two code paths: the ascending path and descending path - * (analogous to bsf and bsr), where the next limit is a funtion of the + * (analogous to bsf and bsr), where the next limit is a function of the * next set bit in a forward or backward sequence of bits (as a function * of the Limit). We start with the ascending path, to ensure that * regions are naturally aligned, then we switch to the descending path @@ -213,7 +213,7 @@ u32 lo, hi;
/*====================================================================== - * Adjust temp top of memory down to accomodate UMA memory start + * Adjust temp top of memory down to accommodate UMA memory start *======================================================================*/ /* Bottom32bIO=sub 4GB top of memory, right justified 8 bits * (defines dram versus IO space type)
Modified: trunk/src/northbridge/amd/amdmct/mct_ddr3/mhwlc_d.c ============================================================================== --- trunk/src/northbridge/amd/amdmct/mct_ddr3/mhwlc_d.c Sat Oct 9 04:31:10 2010 (r5927) +++ trunk/src/northbridge/amd/amdmct/mct_ddr3/mhwlc_d.c Sat Oct 9 09:18:50 2010 (r5928) @@ -91,7 +91,7 @@ DRAM_ADD_DCT_PHY_CONTROL_REG, WrtLvTrEn, WrtLvTrEn, 1); else { - /* Broadcast write to all D3Dbyte chiplet register offset 0xc + /* Broadcast write to all D3Dbyte chipset register offset 0xc * Set bit 0 (wrTrain) * Program bit 4 to nibble being trained (only matters for x4dimms) * retain value of 3:2 (Trdimmsel) @@ -114,7 +114,7 @@ AmdMemPCIReadBits(MAKE_SBDFO(0,0,24+(pDCTData->NodeId),FUN_DCT,Addl_Data_Port), 31, 0, &Value); Value = bitTestSet(Value, 0); /* enable WL training */ Value = bitTestReset(Value, 4); /* for x8 only */ - Value = bitTestReset(Value, 5); /* for harward WL training */ + Value = bitTestReset(Value, 5); /* for hardware WL training */ AmdMemPCIWriteBits(MAKE_SBDFO(0,0,24+(pDCTData->NodeId),FUN_DCT,Addl_Data_Port), 31, 0, &Value); Addr=0x4D030F0C; AmdMemPCIWriteBits(MAKE_SBDFO(0,0,24+(pDCTData->NodeId),FUN_DCT,Addl_Data_Offset), 31, 0, &Addr); @@ -172,7 +172,7 @@ * Parameters: * IN OUT *DCTData - Pointer to buffer with information about each DCT * IN u32: MRS value - * OUT u32: sWAPPED BANK BITS + * OUT u32: Swapped BANK BITS * * ---------------------------------------------------------------------------- */ @@ -208,7 +208,7 @@ * Parameters: * IN OUT *DCTData - Pointer to buffer with information about each DCT * IN u32: MRS value - * OUT u32: sWAPPED BANK BITS + * OUT u32: Swapped BANK BITS * * ---------------------------------------------------------------------------- */ @@ -262,7 +262,7 @@ MemClkFreq = get_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_CONFIG_HIGH, 0, 2); /* Configure the DCT to send initialization MR commands to the target DIMM - * ;by programming the F2x[1,0]7C register using the following steps. + * by programming the F2x[1,0]7C register using the following steps. */ rank = 0; while ((rank < pDCTData->DimmRanks[dimm]) && (rank < 2)) @@ -271,14 +271,14 @@ set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsChipSelStart, MrsChipSelEnd, dimm*2+rank); /* Program F2x[1, 0]7C[MrsBank[2:0]] for the appropriate internal DRAM - * ;register that defines the required DDR3-defined function for write - * ; levelization. + * register that defines the required DDR3-defined function for write + * levelization. */ MrsBank = swapBankBits(pDCTData,1); set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsBankStart, MrsBankEnd, MrsBank); /* Program F2x[1, 0]7C[MrsAddress[15:0]] to the required DDR3-defined function - * ; for write levelization. + * for write levelization. */ tempW = 0;/* DLL_DIS = 0, DIC = 0, AL = 0, TDQS = 0 */
@@ -347,7 +347,7 @@ tempW1 = bitTestSet(tempW, MRS_Level); if (rank == 0) { - /* ?Enable the output driver of the first rank of the target DIMM. */ + /* Enable the output driver of the first rank of the target DIMM. */ tempW = tempW1; } else @@ -371,7 +371,7 @@ set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsAddressStart, MrsAddressEnd, tempW); /* Program F2x[1, 0]7C[SendMrsCmd]=1 to initiate the command to - * ;the specified DIMM. + * the specified DIMM. */ set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, SendMrsCmd, SendMrsCmd, 1); @@ -381,13 +381,13 @@ { } /* Program F2x[1, 0]7C[MrsBank[2:0]] for the appropriate internal DRAM - * ;register that defines the required DDR3-defined function for Rtt_WR. + * register that defines the required DDR3-defined function for Rtt_WR. */ MrsBank = swapBankBits(pDCTData,2); set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsBankStart, MrsBankEnd, MrsBank); /* Program F2x[1, 0]7C[MrsAddress[15:0]] to the required DDR3-defined function - * ; for Rtt_WR (DRAMTermDyn). + * for Rtt_WR (DRAMTermDyn). */ tempW = 0;/* PASR = 0,*/ /* program MrsAddress[7,6,5:3]=SRT,ASR,CWL, @@ -457,19 +457,19 @@ {
/* Program F2x[1, 0]7C[MrsChipSel[2:0]] for the current rank - * ;to be trained. + * to be trained. */ set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsChipSelStart, MrsChipSelEnd, currDimm*2+rank); /* Program F2x[1, 0]7C[MrsBank[2:0]] for the appropriate internal - * ;DRAM register that defines the required DDR3-defined function - * ; for write levelization. + * DRAM register that defines the required DDR3-defined function + * for write levelization. */ MrsBank = swapBankBits(pDCTData,1); set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsBankStart, MrsBankEnd, MrsBank); /* Program F2x[1, 0]7C[MrsAddress[15:0]] to the required - * ;DDR3-defined function for write levelization. + * DDR3-defined function for write levelization. */ tempW = 0;/* DLL_DIS = 0, DIC = 0, AL = 0, TDQS = 0, Level=0, Qoff=0 */
@@ -528,7 +528,7 @@ set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsAddressStart, MrsAddressEnd, tempW); /* Program F2x[1, 0]7C[SendMrsCmd]=1 to initiate the command - * ; to the specified DIMM. + * to the specified DIMM. */ set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, SendMrsCmd, SendMrsCmd, 1); @@ -537,13 +537,13 @@ pDCTData->NodeId, FUN_DCT, DRAM_INIT, SendMrsCmd, SendMrsCmd)) == 1); /* Program F2x[1, 0]7C[MrsBank[2:0]] for the appropriate internal DRAM - * ;register that defines the required DDR3-defined function for Rtt_WR. + * register that defines the required DDR3-defined function for Rtt_WR. */ MrsBank = swapBankBits(pDCTData,2); set_Bits(pDCTData, pDCTData->CurrDct, pDCTData->NodeId, FUN_DCT, DRAM_INIT, MrsBankStart, MrsBankEnd, MrsBank); /* Program F2x[1, 0]7C[MrsAddress[15:0]] to the required DDR3-defined function - * ; for Rtt_WR (DRAMTermDyn). + * for Rtt_WR (DRAMTermDyn). */ tempW = 0;/* PASR = 0,*/ /* program MrsAddress[7,6,5:3]=SRT,ASR,CWL, @@ -651,7 +651,7 @@ u16 Addl_Data_Offset, Addl_Data_Port;
/* Program F2x[1, 0]9C_x08[WrLvOdt[3:0]] to the proper ODT settings for the - * ;current memory subsystem configuration. + * current memory subsystem configuration. */ programODT(pMCTData, pDCTData, dimm);
@@ -711,12 +711,12 @@ while(ByteLane < MAX_BYTE_LANES) { /* Program an initialization value to registers F2x[1, 0]9C_x[51:50] and - * ;F2x[1, 0]9C_x52 to set the gross and fine delay for all the byte lane fields - * ; If the target frequency is different than 400MHz, BIOS must + * F2x[1, 0]9C_x52 to set the gross and fine delay for all the byte lane fields + * If the target frequency is different than 400MHz, BIOS must * execute two training passes for each DIMM. * For pass 1 at a 400MHz MEMCLK frequency, use an initial total delay value - * ; of 01Fh. This represents a 1UI (UI=.5MEMCLK) delay and is determined - * ;by design. + * of 01Fh. This represents a 1UI (UI=.5MEMCLK) delay and is determined + * by design. */ pDCTData->WLGrossDelay[MAX_BYTE_LANES*dimm+ByteLane] = Seed_Gross; pDCTData->WLFineDelay[MAX_BYTE_LANES*dimm+ByteLane] = Seed_Fine;
Modified: trunk/src/northbridge/amd/amdmct/mct_ddr3/mutilc_d.c ============================================================================== --- trunk/src/northbridge/amd/amdmct/mct_ddr3/mutilc_d.c Sat Oct 9 04:31:10 2010 (r5927) +++ trunk/src/northbridge/amd/amdmct/mct_ddr3/mutilc_d.c Sat Oct 9 09:18:50 2010 (r5928) @@ -64,7 +64,6 @@ }
/*----------------------------------------------------------------------------- - * uint 32 * u32 bitTestSet(u32 csMask,u32 tempD) * * Description: @@ -86,7 +85,6 @@ }
/*----------------------------------------------------------------------------- - * uint 32 * u32 bitTestReset(u32 csMask,u32 tempD) * * Description: @@ -110,12 +108,11 @@ }
/*----------------------------------------------------------------------------- - * uint 32 * u32 get_Bits(DCTStruct *DCTData, u8 DCT, u8 Node, u8 func, u16 offset, * u8 low, u8 high) * * Description: - * This routine Gets the PCT bits from the specidfied Node, DCT and PCI address + * This routine Gets the PCT bits from the specified Node, DCT and PCI address * * Parameters: * IN OUT *DCTData - Pointer to buffer with information about each DCT @@ -161,12 +158,11 @@ }
/*----------------------------------------------------------------------------- - * uint 32 * void set_Bits(DCTStruct *DCTData,u8 DCT,u8 Node,u8 func, u16 offset, * u8 low, u8 high, u32 value) * * Description: - * This routine Sets the PCT bits from the specidfied Node, DCT and PCI address + * This routine Sets the PCT bits from the specified Node, DCT and PCI address * * Parameters: * IN OUT *DCTData - Pointer to buffer with information about each DCT @@ -212,12 +208,11 @@ }
/*------------------------------------------------- - * uint 32 * u32 get_ADD_DCT_Bits(DCTStruct *DCTData,u8 DCT,u8 Node,u8 func, * u16 offset,u8 low, u8 high) * * Description: - * This routine gets the Additional PCT register from Function 2 by specidfied + * This routine gets the Additional PCT register from Function 2 by specified * Node, DCT and PCI address * * Parameters: @@ -251,12 +246,11 @@ }
/*------------------------------------------------- - * uint 32 * void set_DCT_ADDR_Bits(DCTStruct *DCTData, u8 DCT,u8 Node,u8 func, * u16 offset,u8 low, u8 high, u32 value) * * Description: - * This routine sets the Additional PCT register from Function 2 by specidfied + * This routine sets the Additional PCT register from Function 2 by specified * Node, DCT and PCI address * * Parameters: @@ -297,7 +291,6 @@ }
/*------------------------------------------------- - * uint 32 * BOOL bitTest(u32 value, u8 bitLoc) * * Description:
Modified: trunk/src/northbridge/amd/amdmct/mct_ddr3/mwlc_d.h ============================================================================== --- trunk/src/northbridge/amd/amdmct/mct_ddr3/mwlc_d.h Sat Oct 9 04:31:10 2010 (r5927) +++ trunk/src/northbridge/amd/amdmct/mct_ddr3/mwlc_d.h Sat Oct 9 09:18:50 2010 (r5928) @@ -23,7 +23,7 @@ #define MAX_TOTAL_DIMMS 8 /* Maximum Number of DIMMs in systems */ /* (DCT0 + DCT1) */ #define MAX_DIMMS 4 /* Maximum Number of DIMMs on each DCT */ -#define MAX_LDIMMS 4 /* Maximum number of Logial DIMMs per DCT */ +#define MAX_LDIMMS 4 /* Maximum number of Logical DIMMs per DCT */
/*MCT Max variables */ #define MAX_ERRORS 32 /* Maximum number of Errors Reported */