[coreboot] Patch merged into coreboot/master: 050c40f Add an option to enable PCIe root port coalescing

the following patch was just integrated into master:
commit 050c40f1dcee3945709146abf0c8cfd47b4abca3
Author: Duncan Laurie 
Date:   Fri Apr 27 10:30:51 2012 -0700

Add an option to enable PCIe root port coalescing

Background: The PCI spec (3.0-3.2.2.3.4) requires that PCI devices
    implement function 0.  The Linux Kernel therefore will not enumerate
    a PCI device if it does not present a valid config space at function 0.

If a board does not have anything connected to root port 0 and it is
    desired to disable the unused ports in order to save power then this
    will cause the other downstream PCIe devices to go missing as they
    will not be enumerated.

Intel chipsets provide a way to map root port numbers to different PCI
    function numbers, thereby avoiding this issue and allowing root port 0
    to be turned off.

This change adds a new chip config option 'pcie_port_coalesce' that
    will collapse the enabled root ports into a linear map starting at
    zero.  This option defaults to disabled as it can have a confusing
    effect on the system as the declared static devicetree may not match
    what is seen at runtime.  This option is also forced on if the static
    devicetree disables port 0.

When each root port is processed in the early enable stage it looks
    for a lower numbered root port that has been disabled and then swaps
    the two assigned function numbers.

However the mapping register is write-once so it has to keep track of
    the proposed mapping changes until all ports have been processed
    before writing out the final map value.  At this point it also updates
    the function numbers in the static device tree so they are consistent
    with the new layout.

There are a few other closely related fixes in this change:

1) There is a power savings opportunity if an entire bank of ports
    (0-3 or 4-7) are disabled.  This was checking the chipset revision to
    look for CougarPoint B1+ stepping and that was not passing on
    PantherPoint where this should always be applied.  To fix this I added
    a function to determine the chipset type based on comparing the upper
    byte of the device ID.

2) Apply the same chipset type check fix to the IOBP programming.

3) There is another power savings opportunity to enable dynamic clock
    gating on shared PCIe resources which only applies to ports 0 and 4.
    However if 0 or 4 is disabled then the later check to enable this
    would fail as that device is already hidden.

LUMPY current:

00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
      00:1c.3 PCI bridge: Intel Corporation Device 1c16 (rev b5)
      01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
      02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B

LUMPY with PCIe port coalesce enabled:

00:1c.0 PCI bridge: Intel Corporation Device 1c10 (rev b5)
      00:1c.1 PCI bridge: Intel Corporation Device 1c16 (rev b5)
      01:00.0 Network controller: Atheros Communications Inc. Device 0030 (rev 01)
      02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B

Change-Id: I828aa407fdc9c156c1c42eda8e2d893c0aa66eef
    Signed-off-by: Duncan Laurie

Build-Tested: build bot (Jenkins) at Tue May  1 06:27:44 2012, giving +1
See http://review.coreboot.org/979 for details.

-gerrit