15 May
2008
15 May
'08
4:02 p.m.
This is the same as the v3 patches we did earlier. Marc
--
Marc Jones
Senior Firmware Engineer
(970) 226-9684 Office
mailto:Marc.Jones@amd.com
http://www.amd.com/embeddedprocessors
Geode platforms that use a LPC Super I/O had the LPC serial IRQ set to all
the possible IRQs generated by the SIO. This included IRQ 7 as the default
parallel port IRQ. This overlapped with the MFGPT driver setting IRQ7 for it's
own use. This fix removes IRQ7 from the serial IRQ list for all the mainboards
that were setting it to prevent the conflict and crash when the MFGPT driver
loads.
Signed-off-by: Marc Jones marc.jones@amd.com
Index: coreboot-v2/src/mainboard/amd/db800/Config.lb
===================================================================
--- coreboot-v2.orig/src/mainboard/amd/db800/Config.lb 2008-05-15 16:17:34.000000000 -0600
+++ coreboot-v2/src/mainboard/amd/db800/Config.lb 2008-05-15 16:19:49.000000000 -0600
@@ -127,8 +127,8 @@
# IRQ 12 and 1 unmasked, Keyboard and Mouse IRQs. OK
# SIRQ Mode = Active(Quiet) mode. Save power....
# Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse, UARTs, etc IRQs. OK
- register "lpc_serirq_enable" = "0x000010da"
- register "lpc_serirq_polarity" = "0x0000EF25"
+ register "lpc_serirq_enable" = "0x0000105a"
+ register "lpc_serirq_polarity" = "0x0000EFA5"
register "lpc_serirq_mode" = "1"
register "enable_gpio_int_route" = "0x0D0C0700"
register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash
Index: coreboot-v2/src/mainboard/digitallogic/msm800sev/Config.lb
===================================================================
--- coreboot-v2.orig/src/mainboard/digitallogic/msm800sev/Config.lb 2008-05-15 16:17:51.000000000 -0600
+++ coreboot-v2/src/mainboard/digitallogic/msm800sev/Config.lb 2008-05-15 16:20:25.000000000 -0600
@@ -128,9 +128,9 @@
# Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK
# How to get these? Boot linux and do this:
# rdmsr 0x51400025
- register "lpc_serirq_enable" = "0x000010da"
+ register "lpc_serirq_enable" = "0x0000105a"
# rdmsr 0x5140004e -- polairy is high 16 bits of low 32 bits
- register "lpc_serirq_polarity" = "0x0000EF25"
+ register "lpc_serirq_polarity" = "0x0000EFA5"
# mode is high 10 bits (determined from code)
register "lpc_serirq_mode" = "1"
# Don't yet know how to find this.
Index: coreboot-v2/src/mainboard/iei/pcisa-lx-800-r10/Config.lb
===================================================================
--- coreboot-v2.orig/src/mainboard/iei/pcisa-lx-800-r10/Config.lb 2008-05-15 16:20:49.000000000 -0600
+++ coreboot-v2/src/mainboard/iei/pcisa-lx-800-r10/Config.lb 2008-05-15 16:21:23.000000000 -0600
@@ -78,8 +78,8 @@
# IRQ 12 and 1 unmasked, Keyboard and Mouse IRQs. OK
# SIRQ Mode = Active(Quiet) mode. Save power....
# Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse, UARTs, etc IRQs. OK
- register "lpc_serirq_enable" = "0x000010da"
- register "lpc_serirq_polarity" = "0x0000EF25"
+ register "lpc_serirq_enable" = "0x0000105a"
+ register "lpc_serirq_polarity" = "0x0000EFA5"
register "lpc_serirq_mode" = "1"
register "enable_gpio_int_route" = "0x0D0C0700"
register "enable_ide_nand_flash" = "0" # 0:ide mode, 1:flash
Index: coreboot-v2/src/mainboard/pcengines/alix1c/Config.lb
===================================================================
--- coreboot-v2.orig/src/mainboard/pcengines/alix1c/Config.lb 2008-05-15 16:21:53.000000000 -0600
+++ coreboot-v2/src/mainboard/pcengines/alix1c/Config.lb 2008-05-15 16:22:14.000000000 -0600
@@ -148,9 +148,9 @@
# Invert mask = IRQ 12 and 1 are active high. Keyboard and Mouse IRQs. OK
# How to get these? Boot linux and do this:
# rdmsr 0x51400025
- register "lpc_serirq_enable" = "0x000010da"
+ register "lpc_serirq_enable" = "0x0000105a"
# rdmsr 0x5140004e -- polairy is high 16 bits of low 32 bits
- register "lpc_serirq_polarity" = "0x0000EF25"
+ register "lpc_serirq_polarity" = "0x0000EFA5"
# mode is high 10 bits (determined from code)
register "lpc_serirq_mode" = "1"
# Don't yet know how to find this.