Hi again,
Getting rid of u-boot option CONFIG_PCI_PNP fixes the PCI stuff ;)
And I also did an insane hack, which just inject RSDP to right place making the u-boot boot system a kernel and system on AMD 64bit platform (Asrock 939A785G)!
Jumping to boot code at fc0013 POST: 0xf8 entry = 0x00fc0013 lb_start = 0x00100000 lb_size = 0x00094000 adjust = 0x2fd5c000 buffer = 0x2fdc8000 elf_boot_notes = 0x0011ae90 adjusted_boot_notes = 0x2fe76e90 dram init type: 16, base 0 size 1000 type: 1, base 1000 size 9f000 type: 1, base c0000 size 2fe30000 type: 16, base 2fef0000 size 110000 RSDP found at 2fef2400type: 2, base 30000000 size 10000000
U-Boot 2011.03-00214-g24b6bc2-dirty (May 03 2011 - 23:58:39)
DRAM Configuration: Bank #0: 00001000 636 KiB Bank #1: 000c0000 766.2 MiB Bank #2: 00000000 0 Bytes Bank #3: 00000000 0 Bytes ## Unknown flash on Bank 1 - Size = 0x00000000 = 0 MB ## Unknown flash on Bank 2 - Size = 0x00000000 = 0 MB ## Unknown flash on Bank 3 - Size = 0x00000000 = 0 MB Flash: 0 Bytes *** Warning - bad CRC, using default environment
In: serial Out: serial Err: serial IDE: Bus 0: OK Device 0: Model: WDC WD600BB-00CAA1 Firm: 17.07W17 Ser#: WD-WMA8F113824 Type: Hard Disk Capacity: 57241.8 MB = 55.9 GB (117231408 x 512) Net: No ethernet found. Serck Controls eNET boot > ext2ls ide 0:5 /boot <DIR> 4096 . <DIR> 4096 .. 2063256 bzImage <DIR> 4096 filo <DIR> 12288 grub 22608 memdisk 71290880 a.tar <DIR> 4096 a 1225518 System.map-2.6.26-1-amd64 85588 config-2.6.26-1-amd64 1755088 vmlinuz-2.6.26-1-amd64 2172192 bzImage28 2236288 bzImage29 7707622 initrd.img-2.6.26-1-amd64 33554432 disk 2414688 vmlinuz-2.6.32-5-amd64 6802950 initrd.img-2.6.26-1-amd64.bak 104510 config-2.6.32-5-amd64 165084 memtest86+.bin 1660631 System.map-2.6.32-5-amd64 9446666 initrd.img-2.6.32-5-amd64 124648 memtest86.bin 167264 memtest86+_multiboot.bin boot > setenv bootargs console=ttyS0,9600 root=/dev/sda boot > ext2load ext2load - load binary file from a Ext2 filesystem
Usage: ext2load <interface> <dev[:part]> [addr] [filename] [bytes] - load binary file 'filename' from 'dev' on 'interface' to address 'addr' from ext2 filesystem boot > ext2load 0:5 2000000 /boot/bzImage29 ** No boot file defined ** boot > ext2load ide 0:5 2000000 /boot/bzImage29 Loading file "/boot/bzImage29" from ide device 0:5 (hda5) 2236288 bytes read boot > zboot 2000000 Valid Boot Flag Magic signature found Setup Size = 0x00002c00 Moving Real-Mode Code to 0x00090000 (11264 bytes) Using boot protocol version 2.09 Linux kernel version 2.6.29.2 (root@ruiktest) #1 SMP PREEMPT Sat May 2 00:24:59 CEST 2009 Kernel command line: "console=ttyS0,9600 root=/dev/sda" Loading bzImage at address 0x00100000 (2225024 bytes) ## Transferring control to Linux (at address 00090000) ...
Starting kernel ...
copy to 7c0 from 101e3d4 size 166 copied 9c666066 Linux version 2.6.29.2 (root@ruiktest) (gcc version 4.3.2 (Debian 4.3.2-1) ) #1 SMP PREEMPT Sat May 2 00:24:59 CEST 2009 Command line: console=ttyS0,9600 root=/dev/sda KERNEL supported cpus: Intel GenuineIntel AMD AuthenticAMD Centaur CentaurHauls BIOS-provided physical RAM map: BIOS-e801: 0000000000000000 - 000000000009f000 (usable) BIOS-e801: 0000000000100000 - 0000000004000000 (usable) DMI present. AMI BIOS detected: BIOS may corrupt low RAM, working around it. last_pfn = 0x4000 max_arch_pfn = 0x100000000 Scanning 0 areas for low memory corruption modified physical RAM map: modified: 0000000000000000 - 0000000000010000 (reserved) modified: 0000000000010000 - 000000000009f000 (usable) modified: 0000000000100000 - 0000000004000000 (usable) init_memory_mapping: 0000000000000000-0000000004000000 last_map_addr: 4000000 end: 4000000 ACPI: RSDP 000F0540, 0014 (r0 CORE ) ACPI: RSDT 2FEF2424, 0034 (r1 CORE COREBOOT 0 CORE 0) ACPI: HPET 2FEF24C8, 0038 (r1 CORE COREBOOT 0 CORE 0) ACPI: APIC 2FEF2500, 0054 (r1 CORE COREBOOT 0 CORE 0) ACPI: SSDT 2FEF2554, 020C (r2 CORE DYNADATA 2A CORE 2A) ACPI: FACP 2FEF3B49, 00F4 (r3 CORE COREBOOT 0 CORE 0) ...
Rest is attached.
Thanks, Rudolf