On Mon, Sep 24, 2007 at 05:42:02PM -0700, ron minnich wrote:
On 9/24/07, Roman Kononov kononov@dls.net wrote:
On 09/24/2007 03:41 PM, Ward Vandewege wrote:
Any thoughts?
I have s2892 and Sun Ultra40, which have ck804 too. Linux can only detect one hard drive per SATA controller. The second drive is either undetected or times out. On s2892, some HD types, presumably all SATA-II, (Hitachi HDS7280SA for instance), are detected at boot time, but miserably fail later, with lots of log messages from the kernel driver. I compared the PCI configuration registers (other than BARs, MSI, etc.) left by LinuxBIOS and the factory BIOS: they were different.
It is possible that the changed BIOS settings are a bug fix we don't know about. Can we get a list of differences?
The tyan s2891 lspci's etc I made yesterday are here:
http://ward.vandewege.net/s2891/
This is the proprietary BIOS (sata channel 0):
0000:00:07.0 0101: 10de:0054 (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: 10f1:2891 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at 1440 [size=8] Region 1: I/O ports at 1434 [size=4] Region 2: I/O ports at 1438 [size=8] Region 3: I/O ports at 1430 [size=4] Region 4: I/O ports at 1410 [size=16] Region 5: Memory at dd002000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: de 10 54 00 07 00 b0 00 f3 85 01 01 00 00 00 00 10: 41 14 00 00 35 14 00 00 39 14 00 00 31 14 00 00 20: 11 14 00 00 00 20 00 dd 00 00 00 00 f1 10 91 28 30: 00 00 00 00 44 00 00 00 00 00 00 00 0b 01 03 01
0000:00:08.0 0101: 10de:0055 (rev f3) (prog-if 85 [Master SecO PriO]) Subsystem: 10f1:2891 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at 1458 [size=8] Region 1: I/O ports at 144c [size=4] Region 2: I/O ports at 1450 [size=8] Region 3: I/O ports at 1448 [size=4] Region 4: I/O ports at 1420 [size=16] Region 5: Memory at dd003000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: de 10 55 00 07 00 b0 00 f3 85 01 01 00 00 00 00 10: 59 14 00 00 4d 14 00 00 51 14 00 00 49 14 00 00 20: 21 14 00 00 00 30 00 dd 00 00 00 00 f1 10 91 28 30: 00 00 00 00 44 00 00 00 00 00 00 00 0a 01 03 01
And this is linuxBIOS (note how the detected revision is different!):
0000:00:07.0 0101: 10de:0054 (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: 10f1:2891 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 23 Region 0: I/O ports at 3050 [size=8] Region 1: I/O ports at 3090 [size=4] Region 2: I/O ports at 3060 [size=8] Region 3: I/O ports at 30a0 [size=4] Region 4: I/O ports at 3030 [size=16] Region 5: Memory at fd102000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [b0] Message Signalled Interrupts: 64bit+ Queue=0/2 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [cc] #08 [a802] 00: de 10 54 00 07 00 b0 00 a3 85 01 01 00 00 00 00 10: 51 30 00 00 91 30 00 00 61 30 00 00 a1 30 00 00 20: 31 30 00 00 00 20 10 fd 00 00 00 00 f1 10 91 28 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 01 03 01
0000:00:08.0 0101: 10de:0055 (rev a3) (prog-if 85 [Master SecO PriO]) Subsystem: 10f1:2891 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0 (750ns min, 250ns max) Interrupt: pin A routed to IRQ 22 Region 0: I/O ports at 3070 [size=8] Region 1: I/O ports at 30b0 [size=4] Region 2: I/O ports at 3080 [size=8] Region 3: I/O ports at 30c0 [size=4] Region 4: I/O ports at 3040 [size=16] Region 5: Memory at fd103000 (32-bit, non-prefetchable) [size=4K] Capabilities: [44] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- 00: de 10 55 00 07 00 b0 00 a3 85 01 01 00 00 00 00 10: 71 30 00 00 b1 30 00 00 81 30 00 00 c1 30 00 00 20: 41 30 00 00 00 30 10 fd 00 00 00 00 f1 10 91 28 30: 00 00 00 00 44 00 00 00 00 00 00 00 00 01 03 01
Thanks, Ward.