Author: uwe Date: 2007-11-04 05:04:01 +0100 (Sun, 04 Nov 2007) New Revision: 2939
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/chip.h trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.c trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.h trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_bridge.c trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_early_smbus.c trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_ide.c trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_lpc.c trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_sata.c Log: Various cosmetics, coding style fixes, constifications (trivial).
Signed-off-by: Uwe Hermann uwe@hermann-uwe.de Acked-by: Uwe Hermann uwe@hermann-uwe.de
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/chip.h =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/chip.h 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/chip.h 2007-11-04 04:04:01 UTC (rev 2939) @@ -52,6 +52,7 @@
int ide0_enable:1; int ide1_enable:1; + /* 1 = 80-pin cable */ int ide0_80pin_cable:1; int ide1_80pin_cable:1;
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.c =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.c 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.c 2007-11-04 04:04:01 UTC (rev 2939) @@ -65,8 +65,7 @@ for (i = 0; i < 256; i += 16) { printk_debug("%02x: ", i); for (j = 0; j < 16; j++) { - printk_debug("%02x ", - pci_read_config8(dev, i + j)); + printk_debug("%02x ", pci_read_config8(dev, i + j)); } printk_debug("\n"); } @@ -75,7 +74,7 @@ static void vt8237r_enable(struct device *dev) { struct southbridge_via_vt8237r_config *sb = - (struct southbridge_via_vt8237r_config *) dev->chip_info; + (struct southbridge_via_vt8237r_config *)dev->chip_info;
pci_write_config8(dev, 0x50, sb->fn_ctrl_lo); pci_write_config8(dev, 0x51, sb->fn_ctrl_hi);
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.h =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.h 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r.h 2007-11-04 04:04:01 UTC (rev 2939) @@ -20,43 +20,43 @@ #ifndef SOUTHBRIDGE_VIA_VT8237R_VT8237R_H #define SOUTHBRIDGE_VIA_VT8237R_VT8237R_H
-/* Static resources for the VT8237R southbridge. */ +/* Static resources for the VT8237R southbridge */
-#define VT8237R_APIC_ID 0x2 -#define VT8237R_ACPI_IO_BASE 0x500 -#define VT8237R_SMBUS_IO_BASE 0x400 +#define VT8237R_APIC_ID 0x2 +#define VT8237R_ACPI_IO_BASE 0x500 +#define VT8237R_SMBUS_IO_BASE 0x400 /* 0x0 disabled, 0x2 reserved, 0xf = IRQ15 */ -#define VT8237R_ACPI_IRQ 0x9 -#define VT8237R_HPET_ADDR 0xfed00000ULL -#define VT8237R_APIC_BASE 0xfec00000ULL +#define VT8237R_ACPI_IRQ 0x9 +#define VT8237R_HPET_ADDR 0xfed00000ULL +#define VT8237R_APIC_BASE 0xfec00000ULL
-/* IDE specific defines */ -#define IDE_CS 0x40 -#define IDE_CONF_I 0x41 -#define IDE_CONF_II 0x42 -#define IDE_CONF_FIFO 0x43 -#define IDE_MISC_I 0x44 -#define IDE_MISC_II 0x45 -#define IDE_UDMA 0x50 +/* IDE */ +#define IDE_CS 0x40 +#define IDE_CONF_I 0x41 +#define IDE_CONF_II 0x42 +#define IDE_CONF_FIFO 0x43 +#define IDE_MISC_I 0x44 +#define IDE_MISC_II 0x45 +#define IDE_UDMA 0x50
-/* SMBus specific */ +/* SMBus */ #define VT8237R_POWER_WELL 0x94 #define VT8237R_SMBUS_IO_BASE_REG 0xd0 #define VT8237R_SMBUS_HOST_CONF 0xd2
-#define SMBHSTSTAT (VT8237R_SMBUS_IO_BASE + 0x0) -#define SMBSLVSTAT (VT8237R_SMBUS_IO_BASE + 0x1) -#define SMBHSTCTL (VT8237R_SMBUS_IO_BASE + 0x2) -#define SMBHSTCMD (VT8237R_SMBUS_IO_BASE + 0x3) -#define SMBXMITADD (VT8237R_SMBUS_IO_BASE + 0x4) -#define SMBHSTDAT0 (VT8237R_SMBUS_IO_BASE + 0x5) +#define SMBHSTSTAT (VT8237R_SMBUS_IO_BASE + 0x0) +#define SMBSLVSTAT (VT8237R_SMBUS_IO_BASE + 0x1) +#define SMBHSTCTL (VT8237R_SMBUS_IO_BASE + 0x2) +#define SMBHSTCMD (VT8237R_SMBUS_IO_BASE + 0x3) +#define SMBXMITADD (VT8237R_SMBUS_IO_BASE + 0x4) +#define SMBHSTDAT0 (VT8237R_SMBUS_IO_BASE + 0x5)
-#define HOST_RESET 0xff +#define HOST_RESET 0xff /* 1 in the 0 bit of SMBHSTADD states to READ. */ -#define READ_CMD 0x01 -#define SMBUS_TIMEOUT (100 * 1000 * 10) -#define I2C_TRANS_CMD 0x40 -#define CLOCK_SLAVE_ADDRESS 0x69 +#define READ_CMD 0x01 +#define SMBUS_TIMEOUT (100 * 1000 * 10) +#define I2C_TRANS_CMD 0x40 +#define CLOCK_SLAVE_ADDRESS 0x69
#if DEBUG_SMBUS == 1 #define PRINT_DEBUG(x) print_debug(x)
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_bridge.c =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_bridge.c 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_bridge.c 2007-11-04 04:04:01 UTC (rev 2939) @@ -40,18 +40,18 @@ dump_south(dev); }
-static struct device_operations bridge_ops = { - .read_resources = pci_bus_read_resources, - .set_resources = pci_dev_set_resources, - .enable_resources = pci_bus_enable_resources, - .enable = bridge_enable, - .scan_bus = pci_scan_bridge, - .reset_bus = pci_bus_reset, - .ops_pci = 0, +static const struct device_operations bridge_ops = { + .read_resources = pci_bus_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_bus_enable_resources, + .enable = bridge_enable, + .scan_bus = pci_scan_bridge, + .reset_bus = pci_bus_reset, + .ops_pci = 0, };
-static struct pci_driver northbridge_driver __pci_driver = { - .ops = &bridge_ops, - .vendor = PCI_VENDOR_ID_VIA, - .device = PCI_DEVICE_ID_VIA_K8T890CE_BR, +static const struct pci_driver northbridge_driver __pci_driver = { + .ops = &bridge_ops, + .vendor = PCI_VENDOR_ID_VIA, + .device = PCI_DEVICE_ID_VIA_K8T890CE_BR, };
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_early_smbus.c =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_early_smbus.c 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_early_smbus.c 2007-11-04 04:04:01 UTC (rev 2939) @@ -26,15 +26,15 @@ /** * Print an error, should it occur. If no error, just exit. * - * @param host_status The data returned on the host status register after a - * transaction is processed. + * @param host_status The data returned on the host status register after + * a transaction is processed. * @param loops The number of times a transaction was attempted. */ static void smbus_print_error(u8 host_status, int loops) { /* Check if there actually was an error. */ if ((host_status == 0x00 || host_status == 0x40 || - host_status == 0x42) && (loops < SMBUS_TIMEOUT)) + host_status == 0x42) && (loops < SMBUS_TIMEOUT)) return;
if (loops >= SMBUS_TIMEOUT) @@ -46,13 +46,13 @@ if (host_status & (1 << 2)) print_err("Device error\r\n"); if (host_status & (1 << 1)) - print_debug("Interrupt/SMI# Completed Successfully\r\n"); + print_debug("Interrupt/SMI# completed successfully\r\n"); if (host_status & (1 << 0)) print_err("Host busy\r\n"); }
/** - * Wait for the smbus to become ready to process the next transaction + * Wait for the SMBus to become ready to process the next transaction. */ static void smbus_wait_until_ready(void) { @@ -64,15 +64,17 @@ /* Yes, this is a mess, but it's the easiest way to do it. */ while ((inb(SMBHSTSTAT) & 1) == 1 && loops < SMBUS_TIMEOUT) ++loops; + smbus_print_error(inb(SMBHSTSTAT), loops); }
/** - * Reset and take ownership of the smbus + * Reset and take ownership of the SMBus. */ static void smbus_reset(void) { outb(HOST_RESET, SMBHSTSTAT); + /* Datasheet says we have to read it to take ownership of SMBus. */ inb(SMBHSTSTAT);
@@ -82,10 +84,10 @@ }
/** - * Read a byte from the smbus + * Read a byte from the SMBus. * - * @param dimm The address location of the dimm on the smbus - * @param offset The offset the data is located at + * @param dimm The address location of the DIMM on the SMBus. + * @param offset The offset the data is located at. */ u8 smbus_read_byte(u8 dimm, u8 offset) { @@ -98,6 +100,7 @@ PRINT_DEBUG("\r\n");
smbus_reset(); + /* Clear host data port. */ outb(0x00, SMBHSTDAT0); SMBUS_DELAY(); @@ -108,11 +111,10 @@ dimm |= 1; outb(dimm, SMBXMITADD); outb(offset, SMBHSTCMD); + /* Start transaction, byte data read. */ outb(0x48, SMBHSTCTL); - SMBUS_DELAY(); - smbus_wait_until_ready();
val = inb(SMBHSTDAT0); @@ -138,18 +140,18 @@ PCI_DEVICE_ID_VIA_VT8237R_LPC), 0);
if (dev == PCI_DEV_INVALID) - die("Power Management Controller not found\r\n"); + die("Power management controller not found\r\n");
/* 7 = SMBus Clock from RTC 32.768KHz * 5 = Internal PLL reset from susp */ pci_write_config8(dev, VT8237R_POWER_WELL, 0xa0);
- /* Enable SMBus */ + /* Enable SMBus. */ pci_write_config16(dev, VT8237R_SMBUS_IO_BASE_REG, - VT8237R_SMBUS_IO_BASE | 0x1); + VT8237R_SMBUS_IO_BASE | 0x1);
- /* SMBus Host Configuration, enable */ + /* SMBus Host Configuration, enable. */ pci_write_config8(dev, VT8237R_SMBUS_HOST_CONF, 0x01);
/* Make it work for I/O. */ @@ -162,17 +164,17 @@ }
/** - * A fixup for some systems that need time for the smbus to "warm up". This is - * needed on some vt823x based systems, where the smbus spurts out bad data for - * a short time after power on. This has been seen on the Via Epia-series and + * A fixup for some systems that need time for the SMBus to "warm up". This is + * needed on some VT823x based systems, where the SMBus spurts out bad data for + * a short time after power on. This has been seen on the VIA Epia series and * Jetway J7F2-series. It reads the ID byte from SMBus, looking for * known-good data from a slot/address. Exits on either good data or a timeout. * - * This should probably go into some global file, but one would need to be - * created just for it. If some other chip needs/wants it, we can worry about it - * then. + * TODO: This should probably go into some global file, but one would need to + * be created just for it. If some other chip needs/wants it, we can + * worry about it then. * - * @param ctrl The memory controller and smbus addresses + * @param ctrl The memory controller and SMBus addresses. */ void smbus_fixup(const struct mem_controller *ctrl) { @@ -181,24 +183,31 @@
ram_slots = ARRAY_SIZE(ctrl->channel0); if (!ram_slots) { - print_err("smbus_fixup thinks there are no ram slots!\r\n"); + print_err("smbus_fixup() thinks there are no RAM slots!\r\n"); return; } - - PRINT_DEBUG("Waiting for smbus to warm up"); - - /* Bad SPD data should be either 0 or 0xff, but YMMV. So we look for the - * ID bytes of SDRAM, DDR, DDR2, and DDR3 (and anything in between). - * vt8237r has only been seen on DDR and DDR2 based systems, so far */ - for(i = 0; (i < SMBUS_TIMEOUT && ((result < SPD_MEMORY_TYPE_SDRAM) || - (result > SPD_MEMORY_TYPE_SDRAM_DDR3))); i++) - { - if (current_slot > ram_slots) current_slot = 0; - result = smbus_read_byte(ctrl->channel0[current_slot], - SPD_MEMORY_TYPE); + + PRINT_DEBUG("Waiting for SMBus to warm up"); + + /* + * Bad SPD data should be either 0 or 0xff, but YMMV. So we look for + * the ID bytes of SDRAM, DDR, DDR2, and DDR3 (and anything in between). + * VT8237R has only been seen on DDR and DDR2 based systems, so far. + */ + for (i = 0; (i < SMBUS_TIMEOUT && ((result < SPD_MEMORY_TYPE_SDRAM) || + (result > SPD_MEMORY_TYPE_SDRAM_DDR3))); i++) { + + if (current_slot > ram_slots) + current_slot = 0; + + result = smbus_read_byte(ctrl->channel0[current_slot], + SPD_MEMORY_TYPE); current_slot++; PRINT_DEBUG("."); } - if (i >= SMBUS_TIMEOUT) print_err("SMBus timed out while warming up\r\n"); - else PRINT_DEBUG("Done\r\n"); + + if (i >= SMBUS_TIMEOUT) + print_err("SMBus timed out while warming up\r\n"); + else + PRINT_DEBUG("Done\r\n"); }
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_ide.c =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_ide.c 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_ide.c 2007-11-04 04:04:01 UTC (rev 2939) @@ -34,7 +34,7 @@ static void ide_init(struct device *dev) { struct southbridge_via_vt8237r_config *sb = - (struct southbridge_via_vt8237r_config *) dev->chip_info; + (struct southbridge_via_vt8237r_config *)dev->chip_info;
u8 enables; u32 cablesel; @@ -52,7 +52,7 @@ /* Enable only compatibility mode. */ enables = pci_read_config8(dev, IDE_CONF_II); enables &= ~0xc0; - pci_write_config8(dev,IDE_CONF_II, enables); + pci_write_config8(dev, IDE_CONF_II, enables); enables = pci_read_config8(dev, IDE_CONF_II); printk_debug("Enables in reg 0x42 read back as 0x%x\n", enables);
@@ -84,7 +84,7 @@
/* Cable guy... */ cablesel = pci_read_config32(dev, IDE_UDMA); - cablesel &= ~((1 << 28) | (1 << 20) | (1 <<12) | (1 << 4)); + cablesel &= ~((1 << 28) | (1 << 20) | (1 << 12) | (1 << 4)); cablesel |= (sb->ide0_80pin_cable << 28) | (sb->ide0_80pin_cable << 20) | (sb->ide1_80pin_cable << 12) | @@ -92,17 +92,17 @@ pci_write_config32(dev, IDE_UDMA, cablesel); }
-static struct device_operations ide_ops = { - .read_resources = pci_dev_read_resources, - .set_resources = pci_dev_set_resources, - .enable_resources = pci_dev_enable_resources, - .init = ide_init, - .enable = 0, - .ops_pci = 0, +static const struct device_operations ide_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = ide_init, + .enable = 0, + .ops_pci = 0, };
-static struct pci_driver northbridge_driver __pci_driver = { - .ops = &ide_ops, - .vendor = PCI_VENDOR_ID_VIA, - .device = PCI_DEVICE_ID_VIA_82C586_1, +static const struct pci_driver northbridge_driver __pci_driver = { + .ops = &ide_ops, + .vendor = PCI_VENDOR_ID_VIA, + .device = PCI_DEVICE_ID_VIA_82C586_1, };
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_lpc.c =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_lpc.c 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_lpc.c 2007-11-04 04:04:01 UTC (rev 2939) @@ -90,7 +90,7 @@
/* All delivered to CPU0. */ ioapic_table[0].value_high = (lapicid()) << (56 - 32); - l = (unsigned long *) ioapic_base; + l = (unsigned long *)ioapic_base;
/* Set APIC to FSB message bus. */ l[0] = 0x3; @@ -335,16 +335,16 @@ init_keyboard(dev); }
-static struct device_operations vt8237r_lpc_ops = { - .read_resources = vt8237r_read_resources, - .set_resources = pci_dev_set_resources, - .enable_resources = vt8237r_enable_resources, - .init = &southbridge_init, - .scan_bus = scan_static_bus, +static const struct device_operations vt8237r_lpc_ops = { + .read_resources = vt8237r_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = vt8237r_enable_resources, + .init = &southbridge_init, + .scan_bus = scan_static_bus, };
-static struct pci_driver lpc_driver __pci_driver = { - .ops = &vt8237r_lpc_ops, - .vendor = PCI_VENDOR_ID_VIA, - .device = PCI_DEVICE_ID_VIA_VT8237R_LPC, +static const struct pci_driver lpc_driver __pci_driver = { + .ops = &vt8237r_lpc_ops, + .vendor = PCI_VENDOR_ID_VIA, + .device = PCI_DEVICE_ID_VIA_VT8237R_LPC, };
Modified: trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_sata.c =================================================================== --- trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_sata.c 2007-11-04 03:21:37 UTC (rev 2938) +++ trunk/LinuxBIOSv2/src/southbridge/via/vt8237r/vt8237r_sata.c 2007-11-04 04:04:01 UTC (rev 2939) @@ -42,17 +42,17 @@ pci_write_config8(dev, SATA_MISC_CTRL, reg); }
-static struct device_operations sata_ops = { - .read_resources = pci_dev_read_resources, - .set_resources = pci_dev_set_resources, - .enable_resources = pci_dev_enable_resources, - .init = sata_init, - .enable = 0, - .ops_pci = 0, +static const struct device_operations sata_ops = { + .read_resources = pci_dev_read_resources, + .set_resources = pci_dev_set_resources, + .enable_resources = pci_dev_enable_resources, + .init = sata_init, + .enable = 0, + .ops_pci = 0, };
-static struct pci_driver northbridge_driver __pci_driver = { - .ops = &sata_ops, - .vendor = PCI_VENDOR_ID_VIA, - .device = PCI_DEVICE_ID_VIA_VT6420_SATA, +static const struct pci_driver northbridge_driver __pci_driver = { + .ops = &sata_ops, + .vendor = PCI_VENDOR_ID_VIA, + .device = PCI_DEVICE_ID_VIA_VT6420_SATA, };