Hello,
During boot sequence on DK8-HTX, FILO reports IDE timeout. I've seen in previous postings that PCI_BRUTE_SCAN should be set for AMD64 boards. However, after I made this mod to FILO config. and re-flashed the board, the IDE timeout remains. (log shown below).
FILO config file is listed below. Configuration is release LinuxBIOSv2 2430 w/ FILO 0.5. HDD is E-IDE WD Caviar on primary 0 IDE bus. No SATA drives present.
Is cable-select for IDE HDDs supported, or is jumper needed? Does CMOS need to be programmed, or is it sufficient just to clear it out?
Any other ideas?
Thanks, Chris
------------------------------------------------------------------------ jumping to boot code at 0x1079ac entry = 0x001079ac lb_start = 0x00004000 lb_size = 0x0004a000 adjust = 0xf7fb2000 buffer = 0xf7f6c000 elf_boot_notes = 0x0001c8c0 adjusted_boot_notes = 0xf7fce8c0 FILO version 0.5 (cstillo@clyde) Wed Sep 20 21:39:19 CDT 2006 Press <Enter> for default boot, or <Esc> for boot prompt... timed out boot: hda2:/boot/vmlinuz.lb root=/dev/hda2 initrd=/boot/initrd.lb console=ttyS0, 115200 console=tty0 video=atyfb:1024x768-16 IDE time out No drive detected on IDE channel 0 ------------------------------------------------------------------------
# Use grub instead of autoboot? #USE_GRUB = 1
# Grub menu.lst path #MENULST_FILE = "hda3:/boot/filo/menu.lst" # Via Epia-MII CF boot: #MENULST_FILE = "hde1:/boot/filo/menu.lst"
# time before default menu.lst is chosen. Set to 0 to ignore MENULST_TIMEOUT = 0
# Image filename for automatic boot and optional command line parameter AUTOBOOT_FILE = "hda2:/boot/vmlinuz.lb root=/dev/hda2 initrd=/boot/initrd.lb con sole=ttyS0,115200 console=tty0 video=atyfb:1024x768-16"
# Time in second before booting AUTOBOOT_FILE AUTOBOOT_DELAY = 2
# Driver for hard disk, CompactFlash, and CD-ROM on IDE bus IDE_DISK = 1
# Add a short delay when polling status registers # (required on some broken SATA controllers) # NOTE: Slows down access significantly, so disable # whenever possible. #IDE_DISK_POLL_DELAY = 1
# Use PCMCIA compact flash on Via Epia MII10000 and MII6000E # This device is referred to as hde. #PCMCIA_CF = 1
# Driver for USB Storage #USB_DISK = 1
# VGA text console VGA_CONSOLE = 1 PC_KEYBOARD = 1
# Serial console SERIAL_CONSOLE = 1 SERIAL_IOBASE = 0x3f8 # if SERIAL_SPEED is commented out, the speed will not be changed. SERIAL_SPEED = 115200
# Filesystems FSYS_EXT2FS = 1 FSYS_FAT = 1 FSYS_JFS = 1 FSYS_MINIX = 1 FSYS_REISERFS = 1 FSYS_XFS = 1 FSYS_ISO9660 = 1
# Support for boot disk image in bootable CD-ROM (El Torito) ELTORITO = 1
# PCI support SUPPORT_PCI = 1
# Enable this to scan PCI busses above bus 0 # AMD64 based boards do need this. PCI_BRUTE_SCAN = 1 PCI_BRUTE_SCAN_LIMIT = 2 PCI_BRUTE_SCAN_START = 1 IDE_HINT_BUS = 1 IDE_HINT_DEV = 4 IDE_HINT_FUNC = 4
# Loader for standard Linux kernel image, a.k.a. /vmlinuz LINUX_LOADER = 1
# Boot FILO from Multiboot loader (eg. GRUB) #MULTIBOOT_IMAGE = 1
# PCI_CONFIG_1 = 1