[coreboot] Patch set updated for coreboot: 2bdfda7 Detect whether the OXPCIE card is really present while in the ROM stage.

[Stefan Reinauer]

Stefan Reinauer ([e-mail]) just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/728

-gerrit

commit 2bdfda7e68e9a80fd733abfc08b1e382e5f02ac1
Author: Gabe Black 
Date:   Wed Oct 5 01:52:08 2011 -0700

Detect whether the OXPCIE card is really present while in the ROM stage.

Use an int in CAR global data to store whether or not the OXPCIE serial card
    is actually there. Also, time out if the card doesn't show up quickly enough,
    don't continue initialization if it's not there, and don't make the
    initialization routine default to a card if none is found.

Change-Id: I9c72d3abc6ee2867b77ab2f2180e6f01f647af8c
    Signed-off-by: Gabe Black 
---
 src/arch/x86/lib/romstage_console.c      |    5 ++++-
 src/drivers/oxford/oxpcie/oxpcie_early.c |   20 +++++++++++++++++---
 src/include/uart8250.h                   |    5 +++++
 3 files changed, 26 insertions(+), 4 deletions(-)

diff --git a/src/arch/x86/lib/romstage_console.c b/src/arch/x86/lib/romstage_console.c
index 0f22727..25eda9b 100644
--- a/src/arch/x86/lib/romstage_console.c
+++ b/src/arch/x86/lib/romstage_console.c
@@ -35,7 +35,10 @@ static void console_tx_byte(unsigned char byte)
    	console_tx_byte('\r');

#if CONFIG_CONSOLE_SERIAL8250MEM
-	uart8250_mem_tx_byte(CONFIG_OXFORD_OXPCIE_BASE_ADDRESS + 0x1000, byte);
+	if (oxford_oxpcie_present) {
+		uart8250_mem_tx_byte(
+			CONFIG_OXFORD_OXPCIE_BASE_ADDRESS + 0x1000, byte);
+	}
 #endif
 #if CONFIG_CONSOLE_SERIAL8250
    uart8250_tx_byte(CONFIG_TTYS0_BASE, byte);
diff --git a/src/drivers/oxford/oxpcie/oxpcie_early.c b/src/drivers/oxford/oxpcie/oxpcie_early.c
index 2c7767e..4f7a3cb 100644
--- a/src/drivers/oxford/oxpcie/oxpcie_early.c
+++ b/src/drivers/oxford/oxpcie/oxpcie_early.c
@@ -20,6 +20,8 @@
 #include <stdint.h>
 #include <arch/io.h>
 #include <arch/romcc_io.h>
+#include <cpu/x86/car.h>
+#include <delay.h>
 #include <uart8250.h>
 #include <device/pci_def.h>

@@ -34,9 +36,13 @@
 #define OXPCIE_DEVICE_3 \
    PCI_DEV(CONFIG_OXFORD_OXPCIE_BRIDGE_SUBORDINATE, 0, 3)

+#if defined(__PRE_RAM__)
+int oxford_oxpcie_present CAR_GLOBAL;
+
 void oxford_init(void)
 {
    u16 reg16;
+	oxford_oxpcie_present = 1;

/* First we reset the secondary bus */
    reg16 = pci_read_config16(PCIE_BRIDGE, PCI_BRIDGE_CONTROL);
@@ -69,11 +75,14 @@ void oxford_init(void)
    reg16 |= PCI_COMMAND_MEMORY;
    pci_write_config16(PCIE_BRIDGE, PCI_COMMAND, reg16);

-	// FIXME Add a timeout or this will hang forever if
-	// no device is in the slot.
+	u32 timeout = 20000; // Timeout in 10s of microseconds.
    u32 id = 0;
-	while ((id == 0) || (id == 0xffffffff))
+	for (;;) {
    	id = pci_read_config32(OXPCIE_DEVICE, PCI_VENDOR_ID);
+		if (!timeout-- || (id != 0 && id != 0xffffffff))
+			break;
+		udelay(10);
+	}

u32 device = OXPCIE_DEVICE; /* unknown default */
    switch (id) {
@@ -90,6 +99,10 @@ void oxford_init(void)
    case 0xc1581415: /* e.g. Startech MPEX2S952 */
    	device = OXPCIE_DEVICE;
    	break;
+	default:
+		/* No UART here. */
+		oxford_oxpcie_present = 0;
+		return;
    }

/* Setup base address on device */
@@ -107,3 +120,4 @@ void oxford_init(void)
    uart8250_mem_init(uart0_base, (4000000 / CONFIG_TTYS0_BAUD));
 }

+#endif
diff --git a/src/include/uart8250.h b/src/include/uart8250.h
index aa510e5..71b9a5f 100644
--- a/src/include/uart8250.h
+++ b/src/include/uart8250.h
@@ -135,8 +135,13 @@ void uart8250_mem_init(unsigned base_port, unsigned divisor);
 u32 uart_mem_init(void);
 u32 uartmem_getbaseaddr(void);

+#if defined(__PRE_RAM__) && CONFIG_DRIVERS_OXFORD_OXPCIE && \
+	CONFIG_CONSOLE_SERIAL8250MEM
 /* and special init for OXPCIe based cards */
+extern int oxford_oxpcie_present;
+
 void oxford_init(void);
+#endif

#endif /* __ROMCC__ */