Dear coreboot folks,
finally I was able to test coreboot (master with SeaBIOS) on my Asus M2V-MX SE. Unfortunately GNU/Linux does not get to the LUKS passphrase prompt.
[ 0.010581] ACPI: Unable to load the System Description Tables pnp call arg1=0 [ 0.136009] PnPBIOS: dev_node_info: function not supported on this system [ 0.140001] PnPBIOS: Unable to get node info. Aborting. [ 0.734938] uhci_hcd 0000:00:10.0: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.0 setup! [ 0.736070] uhci_hcd 0000:00:10.0: init 0000:00:10.0 fail, -19 [ 0.740071] ehci-pci 0000:00:10.4: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.4 setup! [ 0.744062] ehci-pci 0000:00:10.4: init 0000:00:10.4 fail, -19 [ 0.761636] uhci_hcd 0000:00:10.1: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.1 setup! [ 0.764067] uhci_hcd 0000:00:10.1: init 0000:00:10.1 fail, -19 [ 0.772078] uhci_hcd 0000:00:10.2: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.2 setup! [ 0.776044] uhci_hcd 0000:00:10.2: init 0000:00:10.2 fail, -19 [ 0.793897] uhci_hcd 0000:00:10.3: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.3 setup! [ 0.796079] uhci_hcd 0000:00:10.3: init 0000:00:10.3 fail, -19 pnp call arg1=5 [ 31.841109] ata4.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 31.848224] ata4.00: failed command: READ DMA [ 31.852644] ata4.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 31.852644] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 31.867303] ata4.00: status: { DRDY }
Passing `acpi=off` I got a little further but there are still SATA issues. Linux reports the following.
[ 1.316609] sata_via 0000:00:0f.0: can't find IRQ for PCI INT B; please try using pci=biosirq [ 1.320966] via_rhine: v1.10-LK1.5.1 2010-10-09 Written by Donald Becker [ 1.324122] usbcore: registered new device driver usb [ 1.328938] sata_via 0000:00:0f.0: routed to hard irq line 0 [ 1.340738] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 1.344646] uhci_hcd: USB Universal Host Controller Interface driver [ 1.348418] ehci-pci: EHCI PCI platform driver [ 1.357184] ------------[ cut here ]------------ [ 1.360096] WARNING: CPU: 0 PID: 75 at /build/linux-tAcKXn/linux-3.11.10/drivers/ata/libata-core.c:6234 ata_host_activate+0xeb/0xf0 [libata]() [ 1.364064] Modules linked in: ehci_pci(+) uhci_hcd(+) ehci_hcd via_rhine(+) pata_via(+) sata_via(+) mii libata usbcore usb_common scsi_mod [ 1.380068] CPU: 0 PID: 75 Comm: modprobe Not tainted 3.11-2-686-pae #1 Debian 3.11.10-1 [ 1.384065] Hardware name: , BIOS [ 1.387697] 00000009 c13e5bc3 00000000 c1049d8e c14ac25c 00000000 0000004b f8478b20 [ 1.396066] 0000185a f84641fb f84641fb f75fd1cc f8471ed0 00000000 f8274560 c1049e4b [ 1.404317] 00000009 00000000 f84641fb f75fd1cc f7496000 c122854f f7707d1f 00000080 [ 1.412315] Call Trace: [ 1.414828] [<c13e5bc3>] ? dump_stack+0x3e/0x4e [ 1.416072] [<c1049d8e>] ? warn_slowpath_common+0x7e/0xa0 [ 1.420074] [<f84641fb>] ? ata_host_activate+0xeb/0xf0 [libata] [ 1.424074] [<f84641fb>] ? ata_host_activate+0xeb/0xf0 [libata] [ 1.428074] [<f8471ed0>] ? ata_bmdma_port_intr+0xf0/0xf0 [libata] [ 1.432071] [<c1049e4b>] ? warn_slowpath_null+0x1b/0x20 [ 1.436074] [<f84641fb>] ? ata_host_activate+0xeb/0xf0 [libata] [ 1.440072] [<c122854f>] ? pcibios_set_master+0x2f/0xb0 [ 1.444073] [<f8272734>] ? svia_init_one+0x2a4/0x5a7 [sata_via] [ 1.448073] [<c13ed7f6>] ? notifier_call_chain+0x46/0x60 [ 1.452074] [<c12dafc5>] ? __pm_runtime_resume+0x45/0x60 [ 1.456073] [<c122a083>] ? pci_device_probe+0x63/0xb0 [ 1.460073] [<c12d1c30>] ? __device_attach+0x30/0x30 [ 1.464072] [<c12d1a74>] ? driver_probe_device+0x54/0x1e0 [ 1.468073] [<c1229f5f>] ? pci_match_device+0xf/0xa0 [ 1.472073] [<c12d1ca1>] ? __driver_attach+0x71/0x80 [ 1.476073] [<c12d02ef>] ? bus_for_each_dev+0x3f/0x70 [ 1.480073] [<c12d1676>] ? driver_attach+0x16/0x20 [ 1.484074] [<c12d1c30>] ? __device_attach+0x30/0x30 [ 1.488074] [<c12d1357>] ? bus_add_driver+0x197/0x230 [ 1.492075] [<c1229e40>] ? store_new_id+0x110/0x110 [ 1.496075] [<c12d21c3>] ? driver_register+0x63/0x120 [ 1.500076] [<c108ecdd>] ? ktime_get+0x4d/0xe0 [ 1.504075] [<f82d9000>] ? 0xf82d8fff [ 1.508076] [<c100205a>] ? do_one_initcall+0x5a/0x150 [ 1.512075] [<f82d9000>] ? 0xf82d8fff [ 1.515879] [<c10428d8>] ? set_memory_nx+0x58/0x60 [ 1.516076] [<c10a0c04>] ? load_module+0x1924/0x2120 [ 1.520078] [<c10a1476>] ? SyS_init_module+0x76/0xa0 [ 1.524077] [<c13ea1d7>] ? syscall_call+0x7/0xb [ 1.528075] ---[ end trace ab2b1229e957e6e0 ]--- [ 1.539612] scsi0 : sata_via [ 1.540195] scsi1 : sata_via [ 1.551726] ata1: SATA max UDMA/133 cmd 0x28a0 ctl 0x28b0 bmdma 0x2880 [ 1.552083] ata2: SATA max UDMA/133 cmd 0x28a8 ctl 0x28b4 bmdma 0x2888 [ 1.566861] scsi2 : pata_via [ 1.572933] scsi3 : pata_via [ 1.575953] ata3: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0x2890 irq 14 [ 1.576085] ata4: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x2898 irq 15 [ 1.586723] via-rhine 0000:00:12.0: can't find IRQ for PCI INT A; please try using pci=biosirq [ 1.588332] via-rhine 0000:00:12.0 eth0: VIA Rhine II at 0x12400, 00:00:de:ad:be:ef, IRQ 0 [ 1.596767] via-rhine 0000:00:12.0 eth0: MII PHY found at address 1, status 0x7949 advertising 0de1 Link 0000 [ 1.607921] uhci_hcd 0000:00:10.0: can't find IRQ for PCI INT A; please try using pci=biosirq [ 1.608087] uhci_hcd 0000:00:10.0: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.0 setup! [ 1.612084] uhci_hcd 0000:00:10.0: init 0000:00:10.0 fail, -19 [ 1.625665] ehci-pci 0000:00:10.4: can't find IRQ for PCI INT C; please try using pci=biosirq [ 1.628090] ehci-pci 0000:00:10.4: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.4 setup! [ 1.632084] ehci-pci 0000:00:10.4: init 0000:00:10.4 fail, -19 [ 1.654457] uhci_hcd 0000:00:10.1: can't find IRQ for PCI INT B; please try using pci=biosirq [ 1.656091] uhci_hcd 0000:00:10.1: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.1 setup! [ 1.660086] uhci_hcd 0000:00:10.1: init 0000:00:10.1 fail, -19 [ 1.681390] uhci_hcd 0000:00:10.2: can't find IRQ for PCI INT C; please try using pci=biosirq [ 1.684094] uhci_hcd 0000:00:10.2: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.2 setup! [ 1.688088] uhci_hcd 0000:00:10.2: init 0000:00:10.2 fail, -19 [ 1.692691] uhci_hcd 0000:00:10.3: can't find IRQ for PCI INT D; please try using pci=biosirq [ 1.696093] uhci_hcd 0000:00:10.3: Found HC with no IRQ. Check BIOS/PCI 0000:00:10.3 setup! [ 1.700089] uhci_hcd 0000:00:10.3: init 0000:00:10.3 fail, -19 [ 1.760100] ata1: SATA link down 1.5 Gbps (SStatus 0 SControl 300) [ 1.972108] ata2: SATA link up 1.5 Gbps (SStatus 123 SControl 300) [ 1.984117] Switched to clocksource tsc [ 2.140327] ata2.00: ATA-8: WDC WD20EARS-60MVWB0, 51.0AB51, max UDMA/100 [ 2.147082] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 0/32) [ 2.160322] ata2.00: configured for UDMA/100 [ 2.164788] scsi 1:0:0:0: Direct-Access ATA WDC WD20EARS-60M 51.0 PQ: 0 ANSI: 5 [ 2.337648] sd 1:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) [ 2.345494] sd 1:0:0:0: [sda] 4096-byte physical blocks [ 2.351152] sd 1:0:0:0: [sda] Write Protect is off [ 2.356082] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA pnp call arg1=5 [ 32.453347] sp5100_tco: SP5100/SB800 TCO WatchDog Timer Driver v0.05 [ 32.859471] ata2: lost interrupt (Status 0x50) [ 32.863997] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 32.871098] ata2.00: failed command: READ DMA [ 32.875513] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 32.875513] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 32.890173] ata2.00: status: { DRDY } [ 32.895147] ata2: soft resetting link [ 33.131698] ata2.00: configured for UDMA/100 [ 33.136030] ata2.00: device reported invalid CHS sector 0 [ 33.141493] ata2: EH complete [ 63.882854] ata2: lost interrupt (Status 0x50) [ 63.887380] ata2.00: limiting speed to UDMA/66:PIO4 [ 63.892316] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 63.899421] ata2.00: failed command: READ DMA [ 63.903836] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 63.903836] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 63.918498] ata2.00: status: { DRDY } [ 63.922224] ata2: soft resetting link [ 64.127077] ata2.00: configured for UDMA/66 [ 64.131321] ata2.00: device reported invalid CHS sector 0 [ 64.136786] ata2: EH complete [ 94.938232] ata2: lost interrupt (Status 0x50) [ 94.942740] ata2.00: limiting speed to UDMA/33:PIO4 [ 94.947672] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [ 94.954771] ata2.00: failed command: READ DMA [ 94.959185] ata2.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in [ 94.959185] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) [ 94.973847] ata2.00: status: { DRDY } [ 94.977570] ata2: soft resetting link [ 95.198465] ata2.00: configured for UDMA/33 [ 95.202705] ata2.00: device reported invalid CHS sector 0 [ 95.208166] ata2: EH complete
Please find the log files attached.
Thanks,
Paul