coreboot

coreboot@coreboot.org

11 participants
39712 discussions

Tyan Thunder K8S Pro (S2882)
by Justin C. Darby 01 Sep '04

01 Sep '04

Hi folks, I haven't been paying attention recently to the list in regards to amd64 support, but I was wondering if the Tyan Thunder K8S Pro (S2882) is yet supported? I tried to check the status page, but there isn't a single 2004 date on it. We have 8 of these boards coming in for a webserver cluster, and just need to boot off of IDE (actually, CF via IDE). I know someone around here works on Tyan boards, so I figure this is the quickest way to an answer. :) Thanks, Justin

3 2

Re: Redirect your console to the network
by ron minnich 01 Sep '04

01 Sep '04

yes, we have used that off and on for a while. I hope they improved it to be a real module, but if not I have an iproved version here ... thanks for the pointer. ron

1 0

Re: VGA Problem about 440bx chipset
by Chiu Gerald 01 Sep '04

01 Sep '04

>From: Richard Smith <rsmith(a)bitworks.com> >To: snow2moutain(a)hotmail.com >CC: linuxbios(a)clustermatic.org >Subject: Re: VGA Problem about 440bx chipset >Date: Tue, 31 Aug 2004 10:33:35 -0500 > >Chiu Gerald wrote: > > > I found the work done about vga are: > > (1) allocate_vga_resource() in newpci.c > > enbale io/mem of the vga adapter > > then walk up the bridges setting the VGA enable > >That should all be done already. > > > (2) copy the vga bios to 0xc0000 using adlo,and run bochs bios. > > I'm not sure if it had initilized the vga controller enough. And I > >You will get a vga bios boot screen if it works. > > > found there are some registers about AGP from 440bx northbridge > > datasheet ( 82443bx hostbridge/controller),such as AGP capability > > identifier register,AGP command register,AGP status register... > > But this work hadn't been done in linuxbios,maybe I need to set these > > registers correctly according to the datasheet to enable AGP? > >This is probally your problem. None of the AGP stuff is setup in the >440bx code. Only PCI cards have been used to date. You will have to >write AGP init code. you mean that PCI card works? Now I changed to a PCI video card,and bochs had run the vga bios,but still nothing happened! I have no idea what should I do next. _________________________________________________________________ 免费下载 MSN Explorer: http://explorer.msn.com/lccn/

2 1

Redirect your console to the network
by Dave Aubin 01 Sep '04

01 Sep '04

Hi, I just came across this and I thought I'd pass it along as a nice tool to have. Especially when one doesn't have VGA and serial isn't working for you. I hope someone else finds it as useful for them as it does for me:) http://technocrat.net/article.pl?sid=04/08/14/0236245&mode=nested <http://technocrat.net/article.pl?sid=04/08/14/0236245&mode=nested> Enjoy, Dave

1 0

vgabios halt
by zhu shi song 01 Sep '04

01 Sep '04

My MB is A6T based on vt8601 and vt82c686. When call vgabios(at 0xc000:0003), it halted. ... INSTALL REAL-MODE IDT DO THE VGA BIOS found VGA: vid=1023, did=8500 0x55 0xAA ...(16 bytes) bus/devfn = 0x100 biosint: # 0x1a, eax 0xb109 ebx 0x100 ecx 0x100 edx 0xb29f biosint: ebp 0x10fd8 esp 0xfc9 edi 0x2 esi 0x14040 biosint: ip 0x56e8 cs 0xc000 flags 0x16 0xb109: bus 1 devfn 0x0 reg 0x2 val 0x8500 biosint: # 0x58, eax 0xc000 ebx 0x100 ecx 0x8500 edx 0x3c2 biosint: ebp 0x10fd8 esp 0xfc7 edi 0x2 esi 0x14040 biosint: ip 0x2329 cs 0xc000 flags 0x246 biosint: Unsupport int #0x58 biosint: # 0xcd, eax 0xc000 ebx 0x100 ecx 0x8500 edx 0x3c2 biosint: ebp 0x10fd8 esp 0xfc7 edi 0x2 esi 0x14040 biosint: ip 0x2329 cs 0xc000 flags 0x246 biosint: Unsupport int #0xcd (halted) __________________________________ Do you Yahoo!? Take Yahoo! Mail with you! Get it on your mobile phone. http://mobile.yahoo.com/maildemo

3 2

Re: Etherboot for AMD64
by Stefan Reinauer 01 Sep '04

01 Sep '04

This question was there before on this list. Does anyone have a pointer or some details? * Sagiv Yefet <sagivy(a)3vium.com> [040901 11:23]: > In the north bridge section of amd/serenade there are the following > entries: > northbridge amd/amdk8 "mc0" > #pci 0:18.0 > #pci 0:18.0 > #pci 0:18.0 > #pci 0:18.1 > #pci 0:18.2 > #pci 0:18.3 > why is 0:18.0 repeated three times ? > > -----Original Message----- > From: Stefan Reinauer [mailto:stepan@openbios.org] > Sent: Monday, August 30, 2004 11:44 AM > To: Sagiv Yefet > Cc: linuxbios(a)clustermatic.org > Subject: Re: Etherboot for AMD64 > > * Sagiv Yefet <sagivy(a)3vium.com> [040830 11:59]: > > What image suit AMD64 in the etherboot project ? > > Thanks. > > You should try tg3--ide_disk.zelf. Or better use YhLu's patches to add > filo and sata > > Stefan > > > >

1 0

Mail Delivery (failure linuxbios@clustermatic.org)
by aip＠cwlinux.com 31 Aug '04

31 Aug '04

1 0

RE: using the cosole device
by YhLu 31 Aug '04

31 Aug '04

You mean baud rate or others. The freebios2 has two Config.lb, one in the mainboard and the other in targets Freebios2/src/mainboard/ Freebios2/targets/. The chipset seeting is in mainboard, and others in targes. Regards YH _____ From: Sagiv Yefet [mailto:sagivy@3vium.com] Sent: Tuesday, August 31, 2004 3:56 AM To: linuxbios(a)clustermatic.org Subject: using the cosole device I am working on AMD64. What are the definition in the Config.lb file define the console device (rs232) Superio winbond/w83627hf Thanks.

2 1

VGA Problem about 440bx chipset
by Chiu Gerald 31 Aug '04

31 Aug '04

HI,all I run linuxbios on a 440bx chipset mainboard using adlo+bochs,I can boot linux but still havn't started up the vga. what should I do if I want to bring up the vga card? I found the work done about vga are: (1) allocate_vga_resource() in newpci.c enbale io/mem of the vga adapter then walk up the bridges setting the VGA enable (2) copy the vga bios to 0xc0000 using adlo,and run bochs bios. I'm not sure if it had initilized the vga controller enough. And I found there are some registers about AGP from 440bx northbridge datasheet ( 82443bx hostbridge/controller),such as AGP capability identifier register,AGP command register,AGP status register... But this work hadn't been done in linuxbios,maybe I need to set these registers correctly according to the datasheet to enable AGP? Regards, Gerald _________________________________________________________________ 免费下载 MSN Explorer: http://explorer.msn.com/lccn

3 4

unsupport int error when vga init
by zhu shi song 31 Aug '04

31 Aug '04

Dear lists, I have two questions: (1) I use getpir(8.30 freebios v1) to get irq_tables.c of epia-500. I have compared mine with one under mainboard/via/epia. They are always different. What cause it? My irq_tables.c is as following: /* This file was generated by getpir.c, do not modify! (but if you do, please run checkpir on it to verify) Contains the IRQ Routing Table dumped directly from your memory , wich BIOS s ets up Documentation at : http://www.microsoft.com/hwdev/busbios/PCIIRQ.HTM */ #include <arch/pirq_routing.h> const struct irq_routing_table intel_irq_routing_table = { PIRQ_SIGNATURE, /* u32 signature */ PIRQ_VERSION, /* u16 version */ 32+16*5, /* there can be total 5 devices on the bus */ 0, /* Where the interrupt router lies (bus) */ 0, /* Where the interrupt router lies (dev) */ 0x1c00, /* IRQs devoted exclusively to PCI usage */ 0, /* Vendor */ 0, /* Device */ 0, /* Crap (miniport) */ { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }, /* u8 rfu[11] */ 0x88, /* u8 checksum , this hase to set to some value that woul d give 0 after the sum of all bytes for this structure (including checksum) */ { {0,0x98, {{0x1, 0xdeb8}, {0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xd eb8}}, 0x2, 0}, {0,0x50, {{0x1, 0xdeb8}, {0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xd eb8}}, 0x3, 0}, {0,0x58, {{0x4, 0xdeb8}, {0x1, 0xdeb8}, {0x2, 0xdeb8}, {0x3, 0xd eb8}}, 0x4, 0}, {0,0x8, {{0x1, 0xdeb8}, {0x2, 0xdeb8}, {0x3, 0xdeb8}, {0x4, 0xde b8}}, 0, 0}, {0x50,0, {{0, 0}, {0, 0}, {0, 0}, {0, 0}}, 0, 0}, } }; (2) I've got QDIA6T MB based on vt8601 and vt82c686. I have made some progress on this MB(8.30 freebios v1). The romimage can find VGABIOS, but unsupport int error occurred. The output log is as following: LinuxBIOS-1.0.0 Tue Aug 31 19:52:18 CST 2004 starting... Enabled first bank of RAM: 0x10000000 bytes Copying LinuxBIOS to ram. Jumping to LinuxBIOS. LinuxBIOS-1.0.0 Tue Aug 31 19:52:18 CST 2004 booting... Finding PCI configuration type. PCI: Using configuration type 1 Scanning PCI bus...PCI: pci_scan_bus for bus 0 PCI: 00:00.0 [1106/0601] PCI: 00:01.0 [1106/8601] PCI: 00:07.0 [1106/0686] PCI: 00:07.2 [1106/3038] PCI: 00:07.3 [1106/3038] PCI: 00:07.4 [1106/3057] PCI: 00:07.5 [1106/3058] PCI: pci_scan_bus for bus 1 PCI: 01:00.0 [1023/8500] PCI: pci_scan_bus returning with max=01 PCI: pci_scan_bus returning with max=01 done Allocating PCI resources... PCI: 00:00.0 register 10(00000008), read-only ignoring it PCI: 00:00.0 register 10(00000008), read-only ignoring it PCI: 00:00.0 register 10(00000008), read-only ignoring it PCI: 00:00.0 register 10(00000008), read-only ignoring it ASSIGN RESOURCES, bus 0 PCI: 00:01.0 1c <- [0x00001000 - 0x00000fff] bus 1 io PCI: 00:01.0 24 <- [0xfe900000 - 0xfe8fffff] bus 1 prefmem PCI: 00:01.0 20 <- [0xfd800000 - 0xfe8fffff] bus 1 mem ASSIGN RESOURCES, bus 1 PCI: 01:00.0 10 <- [0xfd800000 - 0xfdffffff] mem PCI: 01:00.0 14 <- [0xfe800000 - 0xfe81ffff] mem PCI: 01:00.0 18 <- [0xfe000000 - 0xfe7fffff] mem ASSIGNED RESOURCES, bus 1 PCI: 00:07.2 20 <- [0x00001400 - 0x0000141f] io PCI: 00:07.3 20 <- [0x00001420 - 0x0000143f] io PCI: 00:07.5 10 <- [0x00001000 - 0x000010ff] io PCI: 00:07.5 14 <- [0x00001440 - 0x00001443] io PCI: 00:07.5 18 <- [0x00001450 - 0x00001453] io ASSIGNED RESOURCES, bus 0 Allocating VGA resource done. Enabling PCI resourcess...PCI: 00:00.0 cmd <- 06 PCI: 00:01.0 cmd <- 07 PCI: 00:07.0 cmd <- 87 PCI: 00:07.2 cmd <- 01 PCI: 00:07.3 cmd <- 01 PCI: 00:07.4 cmd <- 00 PCI: 00:07.5 cmd <- 01 PCI: 01:00.0 cmd <- 03 done. Initializing PCI devices... PCI devices initialized Disable Cache Bank0 256MB (MA type 0xe) bank 2 MA 0x0: 0 bytes bank 2 MA 0x8: 0 bytes bank 2 MA 0xe: 0 bytes bank 4 MA 0x0: 0 bytes bank 4 MA 0x8: 0 bytes bank 4 MA 0xe: 0 bytes Enable Cache Total 248MB + frame buffer 8MB Enabling shadow DRAM at 0xC0000-0xFFFFF: done totalram: 248M Initializing CPU #0 Enabling cache... Setting fixed MTRRs(0-88) type: UC Setting fixed MTRRs(0-16) type: WB Setting fixed MTRRs(24-88) type: WB DONE fixed MTRRs Setting variable MTRR 0, base: 0MB, range: 128MB, type WB Setting variable MTRR 1, base: 128MB, range: 64MB, type WB Setting variable MTRR 2, base: 192MB, range: 32MB, type WB Setting variable MTRR 3, base: 224MB, range: 16MB, type WB Setting variable MTRR 4, base: 240MB, range: 8MB, type WB DONE variable MTRRs Clear out the extra MTRR's call intel_enable_fixed_mtrr() call intel_enable_var_mtrr() Leave setup_mtrrs done. Max cpuid index : 2 Vendor ID : GenuineIntel Processor Type : 0x00 Processor Family : 0x06 Processor Model : 0x08 Processor Mask : 0x00 Processor Stepping : 0x0a Feature flags : 0x0383fbff Cache/TLB descriptor values: 1 reads required Desc 0x01 : Instr TLB: 4KB pages, 4-way set assoc, 32 entries Desc 0x02 : Instr TLB: 4MB pages, fully assoc, 2 entries Desc 0x03 : Data TLB: 4KB pages, 4-way set assoc, 64 entries Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x00 : null Desc 0x41 : L2 Unified cache: 128K bytes, 4-way set assoc, 32 byte line size Desc 0x08 : Inst cache: 16K bytes, 4-way set assoc, 32 byte line size Desc 0x04 : Data TLB: 4MB pages, 4-way set assoc, 8 entries Desc 0x0c : Data cache: 16K bytes, 2-way or 4-way set assoc, 32 byte line size MTRR check Fixed MTRRs : Enabled Variable MTRRs: Enabled Disabling local apic...done. CPU #0 Initialized Mainboard fixup IDE enable in reg. 48 is 0x3 set IDE reg. 48 to 0x1 IRQs in reg. 4a are 0x4 setting reg. 4a to 0x44 IDE enable in reg.1-40 is 0x8 set IDE reg.1-40 to 0x3 IDE enable in reg.1-40 read back is 0x3 enables in reg 0x9 0x8f enables in reg 0x9 read back as 0x8a command in reg 0x4 0x80 command in reg 0x4 reads back as 0x85 keyboard_on Final mainboard fixup Southbridge fixup keyboard_on IDE enable in reg. 48 is 0x5 set IDE reg. 48 to 0x5 IRQs in reg. 4a are 0x4 setting reg. 4a to 0x44 IDE enable in reg.1-40 is 0x3 set IDE reg.1-40 to 0x3 IDE enable in reg.1-40 read back is 0x3 enables in reg 0x9 0x8a enables in reg 0x9 read back as 0x8a command in reg 0x4 0x85 command in reg 0x4 reads back as 0x85 setting southbridge Assigning IRQ 10 to 0:7.5 Readback = 10 Assigning IRQ 11 to 1:0.0 Readback = 11 INSTALL REAL-MODE IDT DO THE VGA BIOS found VGA: vid=1023, did=8500 0x55 0xaa 0x60 0xeb 0x4d 0x37 0x34 0x30 0x30 0x30 0x37 0xdc 0x73 0x2a 0x2a 0x52 bus/devfn = 0x100 biosint: # 0x1a, eax 0xb109 ebx 0x100 ecx 0x100 edx 0xb1bf biosint: ebp 0x10fd8 esp 0xfc9 edi 0x2 esi 0x13f60 biosint: ip 0x56e8 cs 0xc000 flags 0x16 0xb109: bus 1 devfn 0x0 reg 0x2 val 0x8500 biosint: # 0xd8, eax 0xc000 ebx 0x100 ecx 0x8500 edx 0x3c2 biosint: ebp 0x10fd8 esp 0xfc7 edi 0x2 esi 0x13f60 biosint: ip 0x2329 cs 0xc000 flags 0x246 biosint: Unsupport int #0xd8 biosint: # 0xcd, eax 0xc000 ebx 0x100 ecx 0x8500 edx 0x3c2 biosint: ebp 0x10fd8 esp 0xfc7 edi 0x2 esi 0x13f60 biosint: ip 0x2329 cs 0xc000 flags 0x246 biosint: Unsupport int #0xcd __________________________________ Do you Yahoo!? Yahoo! Mail - 50x more storage than other providers! http://promotions.yahoo.com/new_mail

3 2

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot