coreboot

coreboot@coreboot.org

39717 discussions

[LinuxBIOS] FILO Enabling VIA_SOUND breaks keyboard in Linux? [VIA EPIA-M10000]
by Leon Woestenberg 26 Feb '06

26 Feb '06

Hello, further experimenting with EPIA-M10000: I am using the default FILO 0.4.2 "Config" for x86, except for the AUTOBOOT_FILE which I have set to: AUTOBOOT_FILE = "hdc1:/vmlinuz-2.6.12-10-386 initrd=hdc1:/initrd.img-2.6.12-10-386 root=/dev/hdc2 ro vga=771 console=tty0 console=ttyS0,115200" This time I tried enabling sound: SUPPORT_SOUND = 1 VIA_SOUND = 1 During booting it reported "No sound device found".* The next problem was I had keyboard control during the FILO console, but no longer in Linux. When I changed back to disabling sound and reflashing LinuxBIOS, this problem dissappeared. I have then fully reproduced this whole sequence again from the start. Can the FILO sound probe do this? I thought it is merely scanning PCI? Regards, Leon. * leon@nehemiah:~/sandbox/filo-0.4.2$ sudo lspci -s 00:11.5 0000:00:11.5 Multimedia audio controller: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller (rev 50) leon@nehemiah:~/sandbox/filo-0.4.2$ sudo lspci -n -s 00:11.5 0000:00:11.5 0401: 1106:3059 (rev 50) whereas: leon@nehemiah:~/sandbox/filo-0.4.2/drivers$ tail -n 3 via-sound.c struct sound_driver viasnd_driver[] __sound_driver = { {0x1106, 0x3058, &viasnd_ops}, /* VT82C686 AC97 Audio Controller */ };

1 0

[LinuxBIOS] Checking if FlashROM pin A18 is connected?
by Leon Woestenberg 25 Feb '06

25 Feb '06

Hello, I have a 512 kByte FlashROM but use 256 kByte images so far. I concatenate two of them, so even if address pin A18 is dangling, the CPU reads the image correctly. Now, if I understand correctly, the util/flashrom utility writes (-w) using the Flash programming algorithms, which do not touch A18. And if I understand correctly, it used mmap() to verify the image, which should use A18. Am I correct that by following this procedure, I can find out whether A18 is connected on my motherboard to the FlashROM socket? : dd if=/dev/random of=/tmp/random.bin bs=1024 count=512 flashrom -w /tmp/random.bin flashrom -v tmp/random.bin VERIFIED => A18 is connected Regards, Leon. *do not do this at home, it destroys your BIOS*

3 3

[LinuxBIOS] VGA BIOS dissect.sh
by Leon Woestenberg 25 Feb '06

25 Feb '06

Hello, I found this script to be helpful to me in getting a VGA BIOS binary for my EPIA. --- leon@nehemiah:/tmp$ cat dissect.sh #!/bin/bash for OFFSET in 76607 107793 112921 113603 123297 136064 148043 186053; do dd if=i0100113.bin of=/tmp/rest.lha bs=1 skip=$OFFSET lha tv rest.lha done rm rest.lha --- Also, to get a rough first idea of the offsets: --- leon@nehemiah:/tmp$ grep -b -a -o lh5 i0100113.bin 0:lh5 76354:lh5 107256:lh5 112805:lh5 113207:lh5 122904:lh5 135994:lh5 148041:lh5 185911:lh5 --- Regards, Leon.

2 3

Re: [LinuxBIOS] RES: Rumba target and AMD RDK THINCLIENT
by Li-Ta Lo 24 Feb '06

24 Feb '06

On Wed, 2006-02-22 at 15:12 -0300, Jardel Silveira wrote: > Dear, > > > As a matter of fact, this target doesn´t seem to turn on my board. > The power led is off. > I´ve an FS2 JTAG interface and may be I can do some necessary tests. > I just committed the raminit.c for GX2. Please take a look at it. I presume you have access to the developer web site and docs there? I think I have implemented the DRAM init sequence in their GeodeROM Porting Guide and LX/GX processor data book correctly. But I may be wrong. I also thing probably I have to implement the PLL reset in order for DRAM to work. BTW, hook a serial console. I think the power led is controlled by software. It is off all the way in LinuxBIOS (yes, there is something on the serial console.) -- Li-Ta Lo <ollie(a)lanl.gov> Los Alamos National Lab

2 2

[LinuxBIOS] [RFC] [PATCH] ST M29F040
by Leon Woestenberg 24 Feb '06

24 Feb '06

Hello LinuxBIOS developers, I had to patch flashrom to work with my FlashROM as per the supplied patch. How exactly do I find out what probe/write/verify function triplet is needed. I copied from the AMD part, as to my knowledge the devices are fully compatible. Tested to work on EPIA-M; write/verify and boot LinuxBIOS. Regards, Leon. Index: flash.h =================================================================== --- flash.h (revision 2177) +++ flash.h (working copy) @@ -55,6 +55,7 @@ #define W_49F002U 0x0B /* Winbond w29c020c device code */ #define ST_ID 0x20 +#define ST_M29F040B 0xE2 #define ST_M29F400BT 0xD5 #define MSYSTEMS_ID 0x156f Index: flashchips.c =================================================================== --- flashchips.c (revision 2177) +++ flashchips.c (working copy) @@ -73,6 +73,8 @@ probe_jedec, erase_chip_jedec, write_jedec, NULL}, {"W49F002U", WINBOND_ID, W_49F002U, NULL, 256, 128, probe_jedec, erase_chip_jedec, write_49f002, NULL}, + {"M29F040B", ST_ID, ST_M29F040B, NULL, 512, 64 * 1024, + probe_29f040b, erase_29f040b, write_29f040b, NULL}, {"M29F400BT", ST_ID, ST_M29F400BT, NULL, 512, 64 * 1024, probe_m29f400bt, erase_m29f400bt, write_linuxbios_m29f400bt, NULL}, {"82802ab", 137, 173, NULL, 512, 64 * 1024,

3 5

[LinuxBIOS] supported in v1, not in v2?
by lukesky740＠aol.com 24 Feb '06

24 Feb '06

I noticed in the v1 tree that you support the LEX cv860a motherboard, yet there have been no updates to that tree in a long time (2 years?). I was dissapointed to see that it has not beed added to the v2 tree. Does this mean that there are no plans to include it? As I am new to this, I am uncertain of the ramifications in version difference from v1 to v2. Any insight would be greatly appreciated. Nathan Dragun

3 2

Re: [LinuxBIOS] RES: RES: Rumba target and AMD RDK THINCLIENT
by Stefan Reinauer 24 Feb '06

24 Feb '06

* Jardel Silveira <jardel(a)lesc.ufc.br> [060223 22:54]: > > Dear Mr. Li-Ta Lo, > > > > I´ve access only to the svn respository. I think don´t have access to the > developer web site and docs there. Clarification: All information is freely available at www.linuxbios.org. There is no such thing as a developer web site. You only need to log in to the website to actually _change_ the content. Stefan -- coresystems GmbH · Brahmsstr. 16 · D-79104 Freiburg i. Br. Tel.: +49 761 7668825 · Fax: +49 761 7664613 Email: info(a)coresystems.de · http://www.coresystems.de/

2 1

Re: [LinuxBIOS] EPIA-M LinuxBIOS worked for my EPIA-M 10000
by Adam Talbot 23 Feb '06

23 Feb '06

-Leon My board is close to the MII, but not exact. I have a different south bridge. http://www.bcmcom.com/bcm_product_ebc3266.htm So thinking that I can get the north bridge up, I am hoping that I can get my board to at least give me something out of the console, from there I can start debugging. I dont think the dd if=/dev/mem.... to grab the video bios will work for me, different address range's. Currently I have linuxbios 2177, same as you, but I dont have a computable flash chip (SST39SF040) currently not supported, so I am using an external burner. The biggest bug I am currently stuck on is the linuxbios.rom keeps coming out at 192k and not 256k... No clue what I have wrong. If i can get 256k then just `cat linuxbios.rom >> linuxbios.rom.512` do that twice and I should have a 512 rom. Can I snag a copy of your Config.lb? My current payload is /etc/hosts, I will switch to filo when I can get console running. For now I would just like to see ANY signs of life out of the console. Console is tested and fully running, I currently dont even use a screen, just serial console. -Adam Leon Woestenberg wrote: > Hello Adam, > > found your question on the LinuxBIOS list (see below). > > I just retried the EPIA-M LinuxBIOS code again and it worked for my > EPIA-M 10000 board. Actually, this is the first time I got it working. > SVN HEAD tree (rev 2177) with filo 4.2.0 with Linux 2.6.11 (or so). > > Note that I did *not* get VGA to work under the early LinuxBIOS boot > and FILO boot, it came up when Linux booted. I controlled FILO through > a null-modem serial connection. > > I have attached my notes below. > > Please if you proceed with your EPIA board, keep me in the loop with > your experiences. It's hard to find experiences from stuff that worked. > > note: Seaching for the VGA issue, it seems I should take the VGA BIOS > from some specific version of VIA's BIOS... > > Regards, > > Leon Woestenberg. > > > > [LinuxBIOS] Status of the epia-m > > *Adam Talbot* talbotx at comcast.net > <mailto:linuxbios%40linuxbios.org?Subject=%5BLinuxBIOS%5D%20Status%20of%20the%20epia-m&In-Reply-To=> > /Tue Feb 21 23:13:44 CET 2006/ > > * Previous message: [LinuxBIOS] This should be an easy error... > <http://www.openbios.org/pipermail/linuxbios/2006-February/013515.html> > * Next message: [LinuxBIOS] EPIA M COM2 problem + possible > solution? > <http://www.openbios.org/pipermail/linuxbios/2006-February/013526.html> > * *Messages sorted by:* [ date ] > <http://www.openbios.org/pipermail/linuxbios/2006-February/date.html#13517> > [ thread ] > <http://www.openbios.org/pipermail/linuxbios/2006-February/thread.html#13517> > [ subject ] > <http://www.openbios.org/pipermail/linuxbios/2006-February/subject.html#13517> > [ author ] > <http://www.openbios.org/pipermail/linuxbios/2006-February/author.html#13517> > > > ------------------------------------------------------------------------ > >Is the current epia-m code running? >-Adam > > > > > >------------------------------------------------------------------------ > >http://www.viaarena.com/default.aspx?PageID=22&DSCat=155&DCatType=3 > >i010t117.bin > >rev 2177 of linuxbiosv2 > >Debugging output from the EPIA: > >115200,8n1,first serial port > >Extract VGA BIOS: > >dd if=/dev/mem of=/video.bios.bin \ >bs=1 count=65536 skip=790528 > >Linux sits on: > >/dev/hdc2 on / type ext3 (rw,errors=remount-ro) > >In the 'util/flash_and_burn' directory is the source for the 'flash_rom' > utility, which is great for re-programming the flash chips on the > EPIA-M / MII. > >Correction: should be in 'util/flashrom' directory since 2101 or so. > >apt-get install pciutils >apt-get install pciutils-dev > >leon@nehemiah:~/sandbox/linuxbios/util/flashrom$ sudo -s >root@nehemiah:~/sandbox/linuxbios/util/flashrom# ./flashrom >Calibrating delay loop... ok >No LinuxBIOS table found. >Enabling flash write on VT8235...tried to set 0x45 to 0x55 on VT8235 failed (WARNING ONLY) >SST39SF020A found at physical address: 0xfffc0000 >Flash part is SST39SF020A >OK, only ENABLING flash write, but NOT FLASHING. > >SST39SF020A is a 256k words of 8 bit = 2 Mbit > >ST29SF040A is a 512k words of 8 bit = 4 Mbit > >Note that the EPIA will address the second half of the 4 Mbit Flash! To be sure, copy the bin to >both halves of the flash. > >wget http://felixx.tsn.or.jp/~ts1/filo/filo-0.4.2.tar.bz2 > >[...] > > The main configuration file for the epia-m is in > 'targets/via/epia-m/Config.lb' > > If you need to make any changes to the configuration, for example you wish to > locate filo.elf in a place other than '/filo.elf', or during the more advanced > steps of this HOWTO, then these changes are made to this file. > > You need to re-run the './buildtarget via/epia-m' after any such change. > > Change the configuration file to match the full path of the filo.elf file. > > payload /home/leon/sandbox/linuxbios/filo.elf > > Regenerate the build: > > ./buildtarget via/epia-m > >cd targets/via/epia-m/epia-m > >make > > > >cd filo >edit Config >make > >cp filo.elf ../linuxbios >cd ../linuxbios/targets >./buildtarget via/epia-m >cd via/epia-m/epia-m >edit Makefile > > >serial.c:54.34: serial.c:66.29: console.c:6.21: console.c:16.26: console.c:51.36: console.c:72.71: bist.h:11.34: auto.c:133.28: 0x81a44e0 noop Internal compiler warning: awakening noop? > > > > > >

1 0

[LinuxBIOS] Intel 845GV Support?
by Mike Anderson 22 Feb '06

22 Feb '06

Greetings! Has anyone had any luck with LinuxBios on the i845GV chipset? I found a few references here and there on the mailing list archive, but nothing definitive. TIA, Mike -- --------------------------------------------------------------- Mike Anderson 703.585.9384 CTO/Chief Scientist mike(a)ThePTRGroup.com www.ThePTRGroup.com Embedded, Real-Time Solutions --------------------------------------------------------------- "Software development is like making a baby. You can't make a baby in one month by impregnating nine women. Some things just take time."

1 0

Re: [LinuxBIOS] Rumba target and AMD RDK THINCLIENT
by Ronald G Minnich 22 Feb '06

22 Feb '06

Jardel Silveira wrote: > Dear, > > > > I have an geode gx2 amd rdk thinclient (GEODE GX + CS5535). Is it > possible run rumba target in this system ? > I´ve maked rumba target and tested it, but CRT didn´t work. > > > Thanks for yours help. amazing. Did you get any serial output or anything? This target is very new, Ollie Lo has been working like crazy to get it going just this week. let me know how far it got ... thanks ron

3 3

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot