coreboot September 2007

coreboot@coreboot.org

81 participants
367 discussions

[LinuxBIOS] AMD 690G chipset support in LinuxBIOS v2
by Darmawan Salihun 13 Sep '07

13 Sep '07

Hi all, I've grepped through the source code last night but haven't found code for board that uses this chipset. Is there any support coming down the road? I'm planning to buy a new system for BIOS experiments in the next few days. This chipset is a candidate for me. I want a chipset with onboard video and K8 processor. I choose K8 because the datasheet for the memory controller is readily available. I'm open for any suggestion(s). Basically, I just want a system that can run Vista, support multicore processor and can be used for LinuxBIOS experiments (preferably without soldering stuff needed). Anyway, one further question: hot-flashing can be done on SPI chips as well, right? Regards, Darmawan Salihun -------------------------------------------------------------------- -= Human knowledge belongs to the world =-

4 6

[LinuxBIOS] r2774 build service
by LinuxBIOS information 13 Sep '07

13 Sep '07

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "stepan" checked in revision 2774 to the LinuxBIOS source repository and caused the following changes: Change Log: I still don't understand a word, but I tried to improve the documentation. (trivial) Please fix this if you can. Signed-off-by: Stefan Reinauer <stepan(a)coresystems.de> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Build Log: Compilation of arima:hdama is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2774&device=hdama&vendor=… Compilation of ibm:e325 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2774&device=e325&vendor=i… Compilation of ibm:e326 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2774&device=e326&vendor=i… Compilation of iei:juki-511p is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2774&device=juki-511p&ven… Compilation of iwill:dk8s2 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2774&device=dk8s2&vendor=… Compilation of iwill:dk8x is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2774&device=dk8x&vendor=i… If something broke during this checkin please be a pain in stepan's neck until the issue is fixed. If this issue is not fixed within 24h the revision should be backed out. Best regards, LinuxBIOS automatic build system

1 0

[LinuxBIOS] r2774 - trunk/LinuxBIOSv2/src/northbridge/amd/amdk8
by svn＠openbios.org 13 Sep '07

13 Sep '07

Author: stepan Date: 2007-09-13 15:47:02 +0200 (Thu, 13 Sep 2007) New Revision: 2774 Modified: trunk/LinuxBIOSv2/src/northbridge/amd/amdk8/get_sblk_pci1234.c Log: I still don't understand a word, but I tried to improve the documentation. (trivial) Please fix this if you can. Signed-off-by: Stefan Reinauer <stepan(a)coresystems.de> Acked-by: Stefan Reinauer <stepan(a)coresystems.de> Modified: trunk/LinuxBIOSv2/src/northbridge/amd/amdk8/get_sblk_pci1234.c =================================================================== --- trunk/LinuxBIOSv2/src/northbridge/amd/amdk8/get_sblk_pci1234.c 2007-09-13 09:55:44 UTC (rev 2773) +++ trunk/LinuxBIOSv2/src/northbridge/amd/amdk8/get_sblk_pci1234.c 2007-09-13 13:47:02 UTC (rev 2774) @@ -29,10 +29,12 @@ its successor. Use of the Materials by the Government constitutes acknowledgement of AMD's proprietary rights in them. ============================================================================*/ -// 2005.9 serengeti support -// by yhlu -// 2005.9 yhlu modify that to more dynamic for AMD Opteron Based MB +/* Copyright 2007 coresystems GmbH */ +// 2005.9 yhlu serengeti support +// 2005.9 yhlu modify that to more dynamic for AMD Opteron Based MB +// 2007.9 stepan improve code documentation + #include <console/console.h> #include <device/pci.h> #include <device/pci_ids.h> @@ -79,88 +81,121 @@ #endif -/* why we need pci1234 array - final result for pci1234 will be - pci1234[0] will record sblink and bus range - pci1234[i] will record ht chain i. - it will keep the sequence when some ht io card is not installed. +/** + * Why we need the pci1234[] array + * + * It will keep the sequence of HT devices in the HT link registers even when a + * given HT I/O card is not installed. + * + * The final result for pci1234[] will be + * + * pci1234[0] will record the south bridge link and bus range + * pci1234[i] will record HT chain i. + * + * For example, on the Tyan S2885 linxbios_ram will put the AMD8151 chain (HT + * link 0) into the register 0xE0, and the AMD8131/8111 HT chain into the + * register 0xE4. + * + * So we need to make sure that the south bridge link will always be on + * pci1234[0]. + * + * Imagine a scenario with multiple HT I/O cards, where you don't install HT I/O 1, + * but you only install HT I/O 2 and HT I/O 3. The HT I/Os will end up in registers + * 0xE4 and 0xE8. + * + * But we want to leave pci1234[1] to HT I/O 1 (even though it is disabled), + * and let HT I/O 2 and HT I/O 3 still use pci1234[2] and pci1234[3]. + * + * So we keep the sequence. You need to preset the pci1234[1], pci1234[2], + * pci1234[3] for this purpose. + * + * For this example you need to set + * + * unsigned pci1234[] = { + * 0x0000ff0, + * 0x0000f10, // HT IO 1 card always on node 1 + * 0x0000f20, // HT IO 2 card always on node 2 + * 0x0000f30 // HT IO 3 card always on node 3 + * }; + * + * For 2P + htio(n1) + htio(n0_1) + htio(n1_1), 2P + htio(n1) + 2P + htio(n2) + htio(n3): + * You need an array pci1234[6]: + * + * unsigned pci1234[] = { + * 0x0000ff0, + * 0x0000010, // HT IO 1 card always on node 1 + * 0x0000f00, // HT IO 2 card always on node 0 + * 0x0000110, // HT IO 3 card always on node 1 + * 0x0000f20, // HT IO 4 card always on node 2 + * 0x0000f30 // HT IO 5 card always on node 3 + * }; + * + * + * For 4p+htio(n1)+htio(n2)+htio(n3),4p+htio(n1)+4p+htio(n6)+htio(n7): + * You need an array pci1234[6]: + * + * unsigned pci1234[] = { + * 0x0000ff0, + * 0x0000f10, // HT IO 1 card always on node 1 + * 0x0000f20, // HT IO 2 card always on node 2 + * 0x0000f30, // HT IO 3 card always on node 3 + * 0x0000f60, // HT IO 4 card always on node 6 + * 0x0000f70 // HT IO 5 card always on node 7 + * }; + * + * + * For 2p + htio(n1) + htio(n0_1) + htio(n1_1), 2P + htio(n1) + 2P + + * htio(n2) + htio(n3), 2P + htio(n1) + 4P + htio(n4) + htio(n5), + * you need an array pci1234[8]: + * + * unsigned pci1234[] = { + * 0x0000ff0, + * 0x0000010, // HT IO 1 card always on node 1 + * 0x0000f00, // HT IO 2 card always on node 0 + * 0x0000110, // HT IO 3 card always on node 1 + * 0x0000f20, // HT IO 4 card always on node 2 + * 0x0000f30 // HT IO 5 card always on node 3 + * 0x0000f40, // HT IO 6 card always on node 4 + * 0x0000f50 // HT IO 7 card always on node 5 + * }; + * + * + * For 4P + htio(n1) + htio(n2) + htio(n3), 4p + htio(n1) + 2p + htio(n4) + + * htio(n5), 4p + htio(n1) + 4p + htio(n6) + htio(n7), + * you need an array pci1234[8]: + * + * unsigned pci1234[] = { + * 0x0000ff0, + * 0x0000f10, // HT IO 1 card always on node 1 + * 0x0000f20, // HT IO 2 card always on node 2 + * 0x0000f30, // HT IO 3 card always on node 3 + * 0x0000f40, // HT IO 4 card always on node 4 + * 0x0000f50 // HT IO 5 card always on node 5 + * 0x0000f60, // HT IO 6 card always on node 6 + * 0x0000f70 // HT IO 7 card always on node 7 + * }; + * + * + * So the maximum posible value of HC_POSSIBLE_NUM is 8. (FIXME Why?) + * + * 1n: 3 + * 2n: 2x2 - 1 + * 4n: 1x4 - 2 + * 6n: 2 + * 8n: 2 + * Total: 12 + * + * Just put all the possible HT Node/link to the list tp pci1234[] in + * src/mainboard/<vendor>/<mainboard>get_bus_conf.c + * + * Also don't forget to increase the ACPI_SSDTX_NUM etc (FIXME what else) if + * you have too many SSDTs + * + * What about co-processor in socket 1 on a 2 way system? Or socket 2 and + * socket 3 on a 4 way system? Treat that as an HC, too! + * + */ - for Tyan S2885 the linxbios_ram will put 8151 chain (link 0) to 0xE0 reg, and 8131/8111 on 0xe4 reg, So we need to make sure the sb link - will always on pci1234[0] - for multi ht-io cards, if you don't install htio1, and only installed htio2, htio3, the htio will be on 0xe4, and 0xe8. - but we want to leave pci1234[1] to htio1 (even it is disabled) , and let htio2 and htio3 still use pci1234[2] and pci1234[3] - So we keep the sequence. ---- you need to preset the pci1234[1], pci1234[2], pci1234[3] for this purpose - for example you need set - unsigned pci1234[] = { - 0x0000ff0, - 0x0000f10, // HT IO 1 card always on node 1 - 0x0000f20, // HT IO 2 card always on node 2 - 0x0000f30 // HT IO 3 card always on node 3 - }; - - for 2p+htio(n1)+htio(n0_1)+htio(n1_1),2p+htio(n1)+2p+htio(n2)+htio(n3) : need pci1234[6] - unsigned pci1234[] = { - 0x0000ff0, - 0x0000010, // HT IO 1 card always on node 1 - 0x0000f00, // HT IO 2 card always on node 0 - 0x0000110, // HT IO 3 card always on node 1 - 0x0000f20, // HT IO 4 card always on node 2 - 0x0000f30 // HT IO 5 card always on node 3 - }; - - for 4p+htio(n1)+htio(n2)+htio(n3),4p+htio(n1)+4p+htio(n6)+htio(n7) : need pci1234[6] - unsigned pci1234[] = { - 0x0000ff0, - 0x0000f10, // HT IO 1 card always on node 1 - 0x0000f20, // HT IO 2 card always on node 2 - 0x0000f30, // HT IO 3 card always on node 3 - 0x0000f60, // HT IO 4 card always on node 6 - 0x0000f70 // HT IO 5 card always on node 7 - }; - - - for 2p+htio(n1)+htio(n0_1)+htio(n1_1), 2p+htio(n1)+2p+htio(n2)+htio(n3), 2p+htio(n1)+4p+htio(n4)+htio(n5), need pci1234[8] - unsigned pci1234[] = { - 0x0000ff0, - 0x0000010, // HT IO 1 card always on node 1 - 0x0000f00, // HT IO 2 card always on node 0 - 0x0000110, // HT IO 3 card always on node 1 - 0x0000f20, // HT IO 4 card always on node 2 - 0x0000f30 // HT IO 5 card always on node 3 - 0x0000f40, // HT IO 6 card always on node 4 - 0x0000f50 // HT IO 7 card always on node 5 - }; - - - for 4p+htio(n1)+htio(n2)+htio(n3), 4p+htio(n1)+2p+htio(n4)+htio(n5), 4p+htio(n1)+4p+htio(n6)+htio(n7), need pci1234[8] - unsigned pci1234[] = { - 0x0000ff0, - 0x0000f10, // HT IO 1 card always on node 1 - 0x0000f20, // HT IO 2 card always on node 2 - 0x0000f30, // HT IO 3 card always on node 3 - 0x0000f40, // HT IO 4 card always on node 4 - 0x0000f50 // HT IO 5 card always on node 5 - 0x0000f60, // HT IO 6 card always on node 6 - 0x0000f70 // HT IO 7 card always on node 7 - }; - - - So Max HC_POSSIBLE_NUM is 8 - - 1n: 3 - 2n: 2x2 - 1 - 4n: 1x4 - 2 - 6n: 2 - 8n: 2 - Total: 12 - - just put all the possible ht node/link to the list tp pci1234[] in get_bus_conf.c on MB dir - - Also don't forget to increase the ACPI_SSDTX_NUM etc if you have too much SSDT - - How about co-processor on socket 1 on 2 way system. or socket 2, and socket3 on 4 way system....? treat that as one hc too! - -*/ void get_sblk_pci1234(void) { @@ -178,27 +213,37 @@ sysconf.pci1234[0] = dword; sysconf.hcid[0] = 0; - /*about hardcode numbering for HT_IO support - set the node_id and link_id that could have ht chain in the one array, - then check if is enabled.... then update final value - */ - //here we need to set hcdn - //1. hypertransport.c need to record hcdn_reg together with 0xe0, 0xe4, 0xe8, 0xec when are set - //2. so at the same time we need update hsdn with hcdn_reg here + /* About hardcoded numbering for HT_IO support + * + * Set the node_id and link_id that could have a HT chain in the one + * array, (FIXME: which one?) then check if is enabled. Then update + * final value + */ + /* Here we need to set hcdn + * + * 1. hypertransport.c needs to record hcdn_reg together with 0xe0, + * 0xe4, 0xe8, 0xec when are set (FIXME: when WHAT is set?) + * + * 2. So at the same time we need update hcdn with hcdn_reg here. FIXME: Why? + */ + dev = dev_find_slot(0, PCI_DEVFN(0x18, 1)); + for(j=0;j<4;j++) { uint32_t dwordx; - dwordx = pci_read_config32(dev, 0xe0+j*4); - dwordx &=0xffff0ff1; //keep bus num, node_id, link_num, enable bits - if((dwordx & 0xff1) == dword) { //SBLINK + dwordx = pci_read_config32(dev, 0xe0 + j*4); + dwordx &=0xffff0ff1; /* keep bus num, node_id, link_num, enable bits */ + if((dwordx & 0xff1) == dword) { /* SBLINK */ sysconf.pci1234[0] = dwordx; sysconf.hcdn[0] = sysconf.hcdn_reg[j]; continue; } + if((dwordx & 1) == 1) { - // We need to find out the number of HC - // for exact match + /* We need to find out the number of HC + * for exact match + */ for(i=1;i<sysconf.hc_possible_num;i++) { if((dwordx & 0xff0) == (sysconf.pci1234[i] & 0xff0)) { sysconf.pci1234[i] = dwordx; @@ -206,7 +251,8 @@ break; } } - // for 0xff0 match or same node + + /* For 0xff0 match or same node */ for(i=1;i<sysconf.hc_possible_num;i++) { if((dwordx & 0xff0) == (dwordx & sysconf.pci1234[i] & 0xff0)) { sysconf.pci1234[i] = dwordx;

1 0

[LinuxBIOS] MSI k9n platinum
by Jonas K 13 Sep '07

13 Sep '07

HI! Im interested in the idea of a "upgraded", free bios, I just bought a new motherboard (msi k9n platinum) and started looking on your page and found that some guy started working on it allmost a year back (http://www.openbios.org/pipermail/linuxbios/2006-December/017580.html) but there is no sign of a finished work yet.. Did he abandon the idea or what happened ? Is someone working on a k9n motherboard right now? //Jonas _________________________________________________________________ Ladda upp bilder på ditt Space så kan dina vänner se när du uppdaterar genom Messenger! http://spaces.live.com/

3 2

[LinuxBIOS] r2773 build service
by LinuxBIOS information 13 Sep '07

13 Sep '07

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "uwe" checked in revision 2773 to the LinuxBIOS source repository and caused the following changes: Change Log: Fix abuild run of the MSI MS-6178 (trivial). Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Build Log: Compilation of arima:hdama is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2773&device=hdama&vendor=… Compilation of ibm:e325 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2773&device=e325&vendor=i… Compilation of ibm:e326 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2773&device=e326&vendor=i… Compilation of iei:juki-511p is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2773&device=juki-511p&ven… Compilation of iwill:dk8s2 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2773&device=dk8s2&vendor=… Compilation of iwill:dk8x is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2773&device=dk8x&vendor=i… Configuration of msi:ms6178 has been fixed If something broke during this checkin please be a pain in uwe's neck until the issue is fixed. If this issue is not fixed within 24h the revision should be backed out. Best regards, LinuxBIOS automatic build system

1 0

[LinuxBIOS] r2773 - trunk/LinuxBIOSv2/src/mainboard/msi/ms6178
by svn＠openbios.org 13 Sep '07

13 Sep '07

Author: uwe Date: 2007-09-13 11:55:44 +0200 (Thu, 13 Sep 2007) New Revision: 2773 Modified: trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Options.lb Log: Fix abuild run of the MSI MS-6178 (trivial). Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Options.lb =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Options.lb 2007-09-13 08:38:24 UTC (rev 2772) +++ trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Options.lb 2007-09-13 09:55:44 UTC (rev 2773) @@ -63,6 +63,7 @@ uses CONFIG_CONSOLE_VGA uses CONFIG_PCI_ROM_RUN +default ROM_SIZE = 512 * 1024 default HAVE_FALLBACK_BOOT = 1 default HAVE_MP_TABLE = 0 default HAVE_HARD_RESET = 0

1 0

[LinuxBIOS] r2772 build service
by LinuxBIOS information 13 Sep '07

13 Sep '07

Dear LinuxBIOS readers! This is the automated build check service of LinuxBIOS. The developer "uwe" checked in revision 2772 to the LinuxBIOS source repository and caused the following changes: Change Log: Add a common/global failover.c file which can be used by all (or at least most) mainboards. This should put and end to copy-paste'ing the same file again and again for every mainboard. Fix the build for the MSI MS-6178 target (wrong location of the common failover.c file). Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Corey Osgood <corey.osgood(a)gmail.com> Build Log: Compilation of arima:hdama is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2772&device=hdama&vendor=… Compilation of ibm:e325 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2772&device=e325&vendor=i… Compilation of ibm:e326 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2772&device=e326&vendor=i… Compilation of iei:juki-511p is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2772&device=juki-511p&ven… Compilation of iwill:dk8s2 is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2772&device=dk8s2&vendor=… Compilation of iwill:dk8x is still broken See the error log at http://qa.linuxbios.org/log_buildbrd.php?revision=2772&device=dk8x&vendor=i… Configuration of msi:ms6178 is still broken If something broke during this checkin please be a pain in uwe's neck until the issue is fixed. If this issue is not fixed within 24h the revision should be backed out. Best regards, LinuxBIOS automatic build system

1 0

Re: [LinuxBIOS] r2772 - in trunk/LinuxBIOSv2/src: arch/i386/lib mainboard/msi/ms6178
by Adrian Reber 13 Sep '07

13 Sep '07

On Thu, Sep 13, 2007 at 10:38:24AM +0200, svn(a)openbios.org wrote: > + * You should have received a copy of the GNU General Public License > + * along with this program; if not, write to the Free Software > + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA > + */ > + > +#define ASSEMBLY 1 I am not really sure how this is used... But gcc defines, at least since 2.95, __ASSEMBLER__ if compiling an assembler file. So it is not really necessary if you have for example an include file which should do certain parts only if included in assembler code. Adrian

1 0

[LinuxBIOS] [PATCH] Build fix for MSI MS-6178
by Uwe Hermann 13 Sep '07

13 Sep '07

See patch. In addition to _this_ patch, my failover.c patch (no ACKs yet) needs to be committed, too, to really fix the build. Uwe. -- http://www.hermann-uwe.de | http://www.holsham-traders.de http://www.crazy-hacks.org | http://www.unmaintained-free-software.org

2 2

[LinuxBIOS] r2772 - in trunk/LinuxBIOSv2/src: arch/i386/lib mainboard/msi/ms6178
by svn＠openbios.org 13 Sep '07

13 Sep '07

Author: uwe Date: 2007-09-13 10:38:24 +0200 (Thu, 13 Sep 2007) New Revision: 2772 Added: trunk/LinuxBIOSv2/src/arch/i386/lib/failover.c Modified: trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Config.lb Log: Add a common/global failover.c file which can be used by all (or at least most) mainboards. This should put and end to copy-paste'ing the same file again and again for every mainboard. Fix the build for the MSI MS-6178 target (wrong location of the common failover.c file). Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Corey Osgood <corey.osgood(a)gmail.com> Added: trunk/LinuxBIOSv2/src/arch/i386/lib/failover.c =================================================================== --- trunk/LinuxBIOSv2/src/arch/i386/lib/failover.c (rev 0) +++ trunk/LinuxBIOSv2/src/arch/i386/lib/failover.c 2007-09-13 08:38:24 UTC (rev 2772) @@ -0,0 +1,49 @@ +/* + * This file is part of the LinuxBIOS project. + * + * Copyright (C) 2007 Uwe Hermann <uwe(a)hermann-uwe.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#define ASSEMBLY 1 + +#include <arch/io.h> +#include "arch/romcc_io.h" +#include "pc80/mc146818rtc_early.c" + +/** + * Check whether the normal or the fallback image should be booted + * (by reading the proper flag from CMOS), and boot it. + * + * @param bist The input BIST value. + * @return The BIST value. + */ +static unsigned long main(unsigned long bist) +{ + if (do_normal_boot()) + goto normal_image; + else + goto fallback_image; + +normal_image: + __asm__ __volatile__("jmp __normal_image" : : "a" (bist) : ); + +cpu_reset: + __asm__ __volatile__("jmp __cpu_reset" : : "a" (bist) : ); + +fallback_image: + return bist; +} Modified: trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Config.lb =================================================================== --- trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Config.lb 2007-09-12 22:11:33 UTC (rev 2771) +++ trunk/LinuxBIOSv2/src/mainboard/msi/ms6178/Config.lb 2007-09-13 08:38:24 UTC (rev 2772) @@ -35,12 +35,12 @@ if HAVE_PIRQ_TABLE object irq_tables.o end # object reset.o makerule ./failover.E - depends "$(MAINBOARD)/../../../lib/failover.c ./romcc" - action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../lib/failover.c -o $@" + depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc" + action "./romcc -E -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@" end makerule ./failover.inc - depends "$(MAINBOARD)/../../../lib/failover.c ./romcc" - action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../lib/failover.c -o $@" + depends "$(MAINBOARD)/../../../arch/i386/lib/failover.c ./romcc" + action "./romcc -O --label-prefix=failover -I$(TOP)/src -I. $(CPPFLAGS) $(MAINBOARD)/../../../arch/i386/lib/failover.c -o $@" end makerule ./auto.E # depends "$(MAINBOARD)/auto.c option_table.h ./romcc"

1 0

← Newer
1
...
21
22
23
24
25
26
27
...
37
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot September 2007