coreboot November 2005

coreboot@coreboot.org

38 participants
84 discussions

RE: [LinuxBIOS] S2882 Memory Hang
by Lu, Yinghai 07 Nov '05

07 Nov '05

1. You don't need to lift your cpu apic id above 0x10. 2. for amd8111 sb, when you do that, kernel will hang, because jiffies will not change. So remove 0x10 in your k8_secondart_stop..... And hard code apicid_base to 4 It should work.... YH -----Original Message----- From: linuxbios-bounces(a)openbios.org [mailto:linuxbios-bounces@openbios.org] On Behalf Of Matthew Simmons Sent: Friday, November 04, 2005 2:11 PM To: linuxbios(a)openbios.org Subject: [LinuxBIOS] S2882 Memory Hang I am currently trying get LinuxBios up and running on my Tyan S2882. After hard coding the apicid_base = 1 in the mptable.c I was finally able to successfully build a bios image for my system. I am using filo as the payload and the configuration of that went well. Both LinuxBios and filo are working as expected. The problem occurs when I attempt to boot the kernel. The kernel stops after the memory manager loads. There are no errors or panics. The system just locks up. I was wondering if any of you have seen this problem, or know of a work around. I am including the kernel output from the serial console. As well as a brief description of the configuration of the system. Thanks for your help, Matthew Simmons Configuration: ---------------------------------------------- Tyan S2882 2x Opteron 248 Processors 1024mb Ram (512x per processor) LinuxBIOSv2 (Revision 2084) Kernel: 2.6.12.1 with the Realtime Preempt Patch Base OS: SuSE 9.2 GCC version: 3.3.2 Serial Console Output: (Sorry for the length) ------------------------------------------------ LinuxBIOS-1.1.8_s2882_Fallback Fri Nov 4 12:47:40 CST 2005 starting... (0,1) link=01 (1,0) link=01 02 nodes initialized. SBLink=00 NC node|link=00 Ram1.00 Ram1.01 Ram2.00 Ram2.01 Ram3 Initializing memory: done Initializing memory: done Clearing initial memory region: done Ram4 Copying LinuxBIOS to ram. Jumping to LinuxBIOS. LinuxBIOS-1.1.8_s2882_Fallback Fri Nov 4 12:47:40 CST 2005 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled CPU: APIC: 10 enabled PCI: 00:19.0 [1022/1100] enabled PCI: 00:19.1 [1022/1101] enabled PCI: 00:19.2 [1022/1102] enabled PCI: 00:19.3 [1022/1103] enabled CPU: APIC: 11 enabled PCI: pci_scan_bus for bus 0 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled PCI: 00:19.0 [1022/1100] enabled PCI: 00:19.1 [1022/1101] enabled PCI: 00:19.2 [1022/1102] enabled PCI: 00:19.3 [1022/1103] enabled PCI: 01:00.0 [1022/7450] en PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003 PCI: 01:00.0 [1022/7460] enabled PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007 PCI: pci_scan_bus for bus 1 PCI: 01:01.0 [1022/7450] enabled PCI: 01:01.1 [1022/7451] enabled PCI: 01:02.0 [1022/7450] enabled PCI: 01:02.1 [1022/7451] enabled PCI: 01:03.0 [1022/7460] enabled PCI: 01:04.0 [1022/7468] enabled PCI: 01:04.1 [1022/7469] enabled PCI: 01:04.2 [1022/746a] enabled PCI: 01:04.3 [1022/746b] enabled PCI: pci_scan_bus for bus 2 Disabling static device: PCI: 0 Disabling static device: PCI: 02:06.1 PCI: 02:09.0 [14e4/1648] enabled PCI: 02:09.1 [14e4/1648] enabled PCI: pci_scan_bus returning with max=02 PCI: 02: 100MHz PCI-X PCI: pci_scan_bus for bus 3 PCI: 03:04.0 [10ee/3fc6] enabled PCI: pci_scan_bus returning with max=03 PCI: 03: Conventional PCI PCI: pci_scan_bus for bus 4 PCI: 04:00.0 [1022/7464] enabled PCI: 04:00.1 [1022/7464] enabled PCI: 04:05.0 [1095/3114] enabled PCI: 04:06.0 [1002/4752] enabled PCI: 04:08.0 [8086/1229] enabled PCI: pci_scan_bus returning with m PNP: 002e.0 enabled PNP: 002e.1 disabled PNP: 002e.2 enabled PNP: 002e.3 disabled PNP: 002e.5 enabled PNP: 002e.6 disabled PNP: 002e.7 disabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled PNP: 002e.b enabled PCI: pci_scan_bus returning with max=04 PCI: pci_scan_bus returning with max=04 done Allocating resources... Reading resources... PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 2 io PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 2 prefmem PCI: 01:02.0 1c <- [0x00fffff00 PCI: 01:02.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 3 prefmem map page: 16ee: 118 Cannot map page: 16f PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem Cannot map pag Cannot map p Done reading resources. Cannot map pag Allocating VGA resource PCI: 04:06.0 Cannot Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 01:03.0 map page: 174xtra MTRR'sd < Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0 Cannot map Cannot map page: 176 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Cannot map page: 178 page: 14b Setting PCI_BRIDGE_CTL_VGA for bridge Root Devicep page: 14c Setting resources...7a PCI: 00:18.0 1b8 <- [0x00fd400000 - 0x00fd3fffff] prefmem <node 0 link 0> Cannot map page: Cannot map page: 17d PCI: 01:02.1 10 <- [0x00fd301000 - 0x00fd301fff] mem64map page: 17 Cannot map page: 1a8 PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io page: 18 Cannot map page: 1 PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 memge: 191 Cannot map page: 1acnot PCI: 04:00.0 10 <- [0x00fd020000 - 0x00fd020fff] meme: 1ading f Cannot map page PCI: 04:00.1 10 <- [0x00fd021000 - 0x00fd021fff] mem Cannot map page: 1aft map PCI: 04:05.0 10 <- [0x0000001450 - 0x0000001457] ioCann Cannot map page: 1b1age: 19566e: 124M, W PCI: 04:05.0 14 <- [0x0000001470 - 0x0000001473] ioge: 1b Cannot map page: 1bcot ma PCI: 04:05.0 18 <- [0x0000001460 - 0x0000001467] ioot map page: 1bdot map Ca PCI: 04:05.0 1c <- [0x00000014 PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq Cannot map page: 1de Cann PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq P C Can -Cannot map page: 1e0t ma PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] ionot map page: 1e1 Cannot ma PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irqo Cannot map page: 1e3ot map page: 1ca PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io Cannot map page: 1f4 PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io Cannot Cannot map page: 1f6 PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq: 1f7 Cannot m Cannot m PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq Cannot map page: 1f9Cannot map PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] ioage: 1faage: 1ee Canno PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq Cannot map page PNP: 002e.5 init PCI: 01:01.1 cmd <- 146b i NB: Fu PCI: 01:02.0 bridge ctrl <- 0003 PCI: 01:02.0 cmd <- 1460ot ma PCI: 03:04.0 cmd <- 142.0 init PCI: 01:02.1 subsystem <- 10f1/2882 PNP: 002e.0 initd PCI: 01:02.1 cmd <- 146 tables to 0xf0000...do PCI: 01:03.0 bridge ctrl <- 000b PCI: 01:03.0 cmd <- 147ng copy of IRQ routing PCI: 04:00.0 subsystem <- 10f1/2882 PCI: 04:00.0 cmd <- 142PCI: 00:19.1 init:06.0 PCI: 04:00.1 subsystem <- 10f1/2882RQ routing table consistency...PCI: PCI: 04:00.1 cmd <- 142 PCI: 04:05.0 subsystem <- 10f1/2882 check_pirq_routing_table() - irq_ PCI: 04:05.0 cmd <- 143: 0x000f00sc Control.. PCI: 04:06.0 subsystem <- 10f1/2882 PCI: 04:06.0 cmd <- 1c3 33:stre PCI: 01:04.1 cmd <- 1410xfffe0000 - 0xfffe6fff PCI: 01:04.2 subsystem <- 10f1/2882 Found PCI: 01:04.2 cmd <- 141 PCI: 01:04.3 subsystem <- 10f1/2882 Loading Ethe PCI: 01:04.3 cmd <- 141 PCI: 00:18.1 subsystem <- 10f1/2882ing non PT_LOAD segment PCI: 00:18.1 cmd <- 140ot 5.2.6 (GPL) http://e PCI: 00:18.2 subsystem <- 10f1/2882 hda4:/boot/vmlinuz initrd=/boot/in PCI: 00:18.2 cmd <- 140ons PCI: 00:18.3 cmd <- 140 PCI: 00:19.0 cmd <- 140 PCI: 00:19.1 cmd <- 140 hda: LBA48: HDS7280 Initializing CPU #0 CPU: vendor AMD device f5aack Fri Nov 4 13:59:37 CS Enabling cache... Setting fixed MTRRs(0-88) type: UC Found Lin Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM (0,1) link=01host) # Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM 02 nodes initialized. DONE fixed MTRRsSBLink=00and lin Setting variable MTRR 0, base: 0MB, range: 1024MB, type WB ht reset -canning NU DONE variable MTRRs2_Fallback Fri Nov Clear out the extra MTRR'sng... MTRR check Fixed MTRRs : Enabled Linux version Variable MTRRs: Enabledeko@buildho Setting up local apic..=01on 3 Copying Lin Enabling cachepe 16 Setting fixed MTRRs(0-88) type: UCnuxBIOS. BIO Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM4 13:59:37 CST 2005 booting... Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM BIOS-e820: 00000000000f0000 - 000 DONE fixed MTRRs Enumeratin Setting variable MTRR 0, base: 0MB, range: 1024MB, type WB Scanning NU PCI_DOMAIN: 0000 enabl DONE variable MTRRs CPU: Clear out the extra MTRR's 0000000000 MTRR check Fixed MTRRs : Enabled/11 PCI: 00:19.1 [10 All AP CPUs stopped PCI: 00:18.0 initr #17 INVAL PCI: 01:01.0 init 00:19.2 [1022/11 PCI: 02:09.0 init PCI: 02:09.1 init#1 PCI PCI: 01:02.0 init03] enabled PCI: 01:03.0 init I PCI: PCI: 04:05.0 init] enabled00. PCI: 04:06.0 init PCI: rom address for PCI: 04:06.0 = fff80000: 0003 Incorrect Expansion ROM Header Signature 457fCI: 01:00.0 [1022/7460] enabled PCI: 04:08.0 init CPU 0: apertur PCI: 01:04.0 init01:03.0 [1022/746 RTC Initd next_u Invalid CMOS LB checksum enabling HPET @0xf PCI: 00:18.2 init PCI: 00:18.3 initstatic device: PC NB: Function 3 Misc Control.. done. Inode-cache hash table PCI: 00:19.0 init D PCI: 00:19.1 initvice: PCI: 02:06. PCI: 00:19.2 init PCI: 00:19.3 init14e4/1648] enable NB: Function 3 Misc Control.. done. PCI: 03:04.0 init PCI: 02: Devices initializedbledk data, 220k in Copying IRQ routing tables to 0xf0000...done. PCI: pci_scan_bus returning with max= Wrote the mp table end at: 00000020 - 00000214 Moving GDT to 0x500...ok Wrote linuxbios table at: 00000530 - 00000de4 checksum 9515 Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 33:stream_init() - rom_stream: 0xfffe0000 - 0xfffe6fff Found ELF candiate at offset 0 Loading Etherboot version: 5.2.6 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x312bd offset 0xb0 filesize 0x6c5b (cleaned up) New segment addr 0x20000 size 0x312bd offset 0xb0 filesize 0x6c5b Loading Segment: addr: 0x000000003ff90000 memsz: 0x000000000002a000 filesz: 0x0000000000006c5b Clearing Segment: addr: 0x000000003ff96c5b memsz: 0x00000000000233a5 Loading Segment: addr: 0x000000000004a000 memsz: 0x00000000000072bd filesz: 0x0000000000000000 Clearing Segment: addr: 0x000000000004a000 memsz: 0x00000000000072bd Jumping to boot code at 0x20000 ROM segment 0x0000 length 0x0000 reloc 0x00020000 CPU 2056 Mhz Etherboot 5.2.6 (GPL) http://etherboot.org Tagged ELF for [FILO] Relocating _text from: [00026c60,00052870) to [3fed43f0,3ff00000) Boot from (N)etwork (D)isk or (Q)uit? Probing pci disk...it() - ro Int BIOS-e820: 00000000000f0000 - 00000000000f0400 type 16i Nov 4 13:57:25 C Virtual Wire compatibility mode BIOS-e820: 0000000000100000 - 0000000040000000 (usable)>Product ID: S2882 <6>APIC at: 0xFEE00000hda4 con Scanning NUMA topology in Northbridge 24toppe New segment Virtual Wire compatibility mode. OEM ID: TYAN <6>Product ID: S2882 <6>APIC at: 0xFEE00000 Processor #16 15:5 APIC version 16 Processor #17 15:5 APIC version 16 Processor #17 INVALID. (Max ID: 16). I/O APIC #1 Version 17 at 0xFEC00000. I/O APIC #2 Version 17 at 0xFD300000. I/O APIC #3 Version 17 at 0xFD301000. Processors: 2 Checking aperture... CPU 0: aperture @ f8000000 size 64 MB CPU 1: aperture @ f8000000 size 64 MB Built 2 zonelists Kernel command line: ro root=/dev/hda4 console=ttyS0,115200 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 1990.814 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 1023436k/1048576k available (2452k kernel code, 0k reserved, 942k data, 220k init) -- LinuxBIOS mailing list LinuxBIOS(a)openbios.org http://www.openbios.org/mailman/listinfo/linuxbios

2 1

[LinuxBIOS] status of Geode?
by Adam Talbot 07 Nov '05

07 Nov '05

-linuxbios I have an old 300MHz geode board I would like to get linuxbios on. There is nothing out on the web site about geode systems. I remember that there was work being put into the geode... Did that work ever finish? Does linuxbios now support the geode? -Adam

2 1

[LinuxBIOS] EPIA-M slow
by Jun OKAJIMA 07 Nov '05

07 Nov '05

Hello. First, it booted finally. Thanks a lot. But, one problem. it takes long time to boot. it is very fast once booting is start, even with debugging enabled. But, before it, there is long wait. I mean, wait until a message below comes. (push reset button) (wait, wait, wait,,,, WAIT..... zzzz.... Maybe more than 10 sec!) LinuxBIOS-1.1.8.0Fallback Sun Nov 6 07:39:08 UTC 2005 starting... Enabling mainboard devices Enabling shadow ram (after this, very fast.) Any help? I used this patch also. Maybe this is a cause? But, without this, it does not work. http://www.openbios.org/pipermail/linuxbios/2005-November/012736.html --- Okajima, Jun. Tokyo, Japan. ------------ My env: H/W : EPIA-MII 1.2GHz Mem: Single side DDR. 512MB PC3200 CL3 SAMSUNG. S/W : Debian Sid. root@Debian:/# gcc -v Using built-in specs. Target: i486-linux-gnu Configured with: ../src/configure -v --enable- languages=c,c++,java,f95,objc,ada,treelang -- prefix=/usr --enable-shared --with-system-zlib --libexecdir=/usr/lib -- without-included-gettext -- enable-threads=posix --enable-nls --program-suffix=-4.0 --enable- __cxa_atexit --enable-libstdcxx- allocator=mt --enable-clocale=gnu --enable-libstdcxx-debug --enable-java- gc=boehm --enable-java- awt=gtk --enable-gtk-cairo --with-java-home=/usr/lib/jvm/java-1.4.2-gcj- 4.0-1.4.2.0/jre --enable- mpfr --disable-werror --enable-checking=release i486-linux-gnu Thread model: posix gcc version 4.0.3 20051023 (prerelease) (Debian 4.0.2-3) root@Debian:/# as --version GNU assembler 2.16.91 20050902 Debian GNU/Linux Copyright 2005 Free Software Foundation, Inc. This program is free software; you may redistribute it under the terms of the GNU General Public License. This program has absolutely no warranty. This assembler was configured for a target of `i486-linux-gnu'.

3 3

RE: [LinuxBIOS] get_apicid_base unresolved?
by Lu, Yinghai 06 Nov '05

06 Nov '05

Please check my patch 1025_enable_CAR_init_cpus_get_apicid_base.diff that I sent out 10/26. I will check that in and populate that to s2891.... YH -----Original Message----- From: linuxbios-bounces(a)openbios.org [mailto:linuxbios-bounces@openbios.org] On Behalf Of Greg Johnson Sent: Wednesday, November 02, 2005 4:41 PM To: linuxbios(a)openbios.org Subject: [LinuxBIOS] get_apicid_base unresolved? I'm trying to build LinuxBIOS for a tyan s2891 and am getting linuxbios_ram.o(.text+0x8e22): In function `smp_write_config_table': : undefined reference to `get_apicid_base' Has the issue with get_apicid_base not been resolved yet? Thanks, Greg -- LinuxBIOS mailing list LinuxBIOS(a)openbios.org http://www.openbios.org/mailman/listinfo/linuxbios

3 2

[LinuxBIOS] ASUS P4R8L motherboard
by d0wnl0ad3r d0wnl0ad3r 05 Nov '05

05 Nov '05

Hi all! I would like to ask you is it possible to use linuxbios on ASUS P4R8L motherboard (in ASUS Pundit-R)? Thank you for your help in advance, Gabor PS: the output of lspci -v: 0000:00:00.0 Host bridge: ATI Technologies Inc: Unknown device 5833 (rev 02) Subsystem: Asustek Computer, Inc.: Unknown device 8107 Flags: bus master, 66MHz, medium devsel, latency 64 Memory at f0000000 (32-bit, prefetchable) [size=128M] Memory at eff00000 (32-bit, non-prefetchable) [size=4K] Capabilities: [a0] AGP version 3.0 0000:00:01.0 PCI bridge: ATI Technologies Inc: Unknown device 5838 (prog-if 00 [Normal decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 I/O behind bridge: 0000d000-0000dfff Memory behind bridge: fd900000-fdcfffff Prefetchable memory behind bridge: cfe00000-efdfffff 0000:00:13.0 USB Controller: ATI Technologies Inc: Unknown device 4347 (rev 01) (prog-if 10 [OHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 8108 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177 Memory at fe900000 (32-bit, non-prefetchable) [size=4K] 0000:00:13.1 USB Controller: ATI Technologies Inc: Unknown device 4348 (rev 01) (prog-if 10 [OHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 8108 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177 Memory at fea00000 (32-bit, non-prefetchable) [size=4K] 0000:00:13.2 USB Controller: ATI Technologies Inc: Unknown device 4345 (rev 01) (prog-if 20 [EHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 8108 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 177 Memory at feb00000 (32-bit, non-prefetchable) [size=4K] Capabilities: [dc] Power Management version 2 0000:00:14.0 SMBus: ATI Technologies Inc ATI SMBus (rev 18) Subsystem: Asustek Computer, Inc.: Unknown device 8108 Flags: 66MHz, medium devsel I/O ports at 0a00 [size=16] Memory at 18000000 (32-bit, non-prefetchable) [size=1K] 0000:00:14.1 IDE interface: ATI Technologies Inc: Unknown device 4349 (prog-if 8a [Master SecP PriP]) Subsystem: Asustek Computer, Inc.: Unknown device 8108 Flags: bus master, medium devsel, latency 0, IRQ 185 I/O ports at <ignored> I/O ports at <ignored> I/O ports at <ignored> I/O ports at <ignored> I/O ports at ff00 [size=16] 0000:00:14.3 ISA bridge: ATI Technologies Inc: Unknown device 434c Subsystem: Asustek Computer, Inc.: Unknown device 8108 Flags: bus master, 66MHz, medium devsel, latency 0 0000:00:14.4 PCI bridge: ATI Technologies Inc: Unknown device 4342 (prog-if 01 [Subtractive decode]) Flags: bus master, 66MHz, medium devsel, latency 64 Bus: primary=00, secondary=02, subordinate=03, sec-latency=64 I/O behind bridge: 00001000-0000efff Memory behind bridge: fdd00000-fe2fffff 0000:00:14.5 Multimedia audio controller: ATI Technologies Inc IXP150 AC'97 Audio Controller Subsystem: Asustek Computer, Inc.: Unknown device 810d Flags: bus master, 66MHz, slow devsel, latency 64, IRQ 193 Memory at fe800000 (32-bit, non-prefetchable) [size=256] 0000:01:05.0 VGA compatible controller: ATI Technologies Inc: Unknown device 5834 (prog-if 00 [VGA]) Subsystem: Asustek Computer, Inc.: Unknown device 8107 Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 185 Memory at d0000000 (32-bit, prefetchable) [size=256M] I/O ports at d000 [size=256] Memory at fdc00000 (32-bit, non-prefetchable) [size=64K] Expansion ROM at fdb00000 [disabled] [size=128K] Capabilities: [58] AGP version 3.0 Capabilities: [50] Power Management version 2 0000:02:08.0 Ethernet controller: 3Com Corporation 3Com 3C920B-EMB-WNM Integrated Fast Ethernet Controller (rev 40) Subsystem: Asustek Computer, Inc.: Unknown device 8108 Flags: bus master, medium devsel, latency 64, IRQ 201 I/O ports at ec00 [size=128] Memory at fe200000 (32-bit, non-prefetchable) [size=128] Expansion ROM at fe100000 [disabled] [size=128K] Capabilities: [dc] Power Management version 2 0000:02:0a.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host Controller (rev 80) (prog-if 10 [OHCI]) Subsystem: Asustek Computer, Inc.: Unknown device 808a Flags: bus master, medium devsel, latency 64, IRQ 201 Memory at fdf00000 (32-bit, non-prefetchable) [size=2K] I/O ports at e880 [size=128] Capabilities: [50] Power Management version 2 0000:02:0c.0 CardBus bridge: ENE Technology Inc CB710 Cardbus Controller (rev 02) Subsystem: ENE Technology Inc CB710 Cardbus Controller Flags: bus master, medium devsel, latency 168, IRQ 185 Memory at 18001000 (32-bit, non-prefetchable) [size=4K] Bus: primary=02, secondary=03, subordinate=06, sec-latency=176 Memory window 0: 18400000-187ff000 (prefetchable) Memory window 1: 18800000-18bff000 I/O window 0: 00004000-000040ff I/O window 1: 00004400-000044ff 16-bit legacy interface ports at 0001 0000:02:0c.1 FLASH memory: ENE Technology Inc CB710 Memory Card Reader Controller Subsystem: ENE Technology Inc CB710 Memory Card Reader Controller Flags: medium devsel, IRQ 177 I/O ports at e800 [size=128] Capabilities: [a0] Power Management version 2 _____________________________________________________________________ Angolul tanulna, de nincs ideje rá? Próbálja ki a levelező módszert. Hanganyag CD-n vagy kazettán. www.elo.hu/free

2 1

[LinuxBIOS] EPIA-M fails for me.
by Jun OKAJIMA 05 Nov '05

05 Nov '05

Hello. I just patched 2084 src tree with Nick Barker's EPIA-M patch, but failed. Give me advise!. The patch I used is this. http://openbios.org/pipermail/linuxbios/2005-October/012723.html http://openbios.org/pipermail/linuxbios/attachments/20051028/2d3ed7d9/epia-… The src is this. http://snapshots.linuxbios.org/LinuxBIOSv2-2084.tar.bz2 What I did is like this. $ tar -xvzf Linuxbios... $ patch -p1 $ ./buildtarget epia-m $ make ( failed!) --- Okajima, Jun. Tokyo, Japan. -------------- _BASE='0xffff0000' -DCONFIG_UDELAY_TSC='1' -DCONFIG_TSC_X86RDTSC_CALIBRATE_WITH_TIMER2='0' -Os - nostdinc -nostdlib -fno-builtin -Wall -o model_centaur_init.o /home/okajima/lx2/LinuxBIOSv2- 2084/src/cpu/via/model_centaur/model_centaur_init.c /home/okajima/lx2/LinuxBIOSv2-2084/src/cpu/via/model_centaur/model_centaur_init.c:29: warning: #warning "FIXME - need correct cpu id here for VIA C3" cc1: Invalid option `32' /home/okajima/lx2/LinuxBIOSv2-2084/src/cpu/via/model_centaur/model_centaur_init.c:45: warning: `used' attribute directive ignored /home/okajima/lx2/LinuxBIOSv2-2084/src/cpu/via/model_centaur/model_centaur_init.c:45: warning: `driver' defined but not used make[1]: *** [model_centaur_init.o] Error 1 make[1]: Leaving directory `/home/okajima/lx2/LinuxBIOSv2-2084/targets/via/epia-m/epia-m/fallback' make: *** [fallback/linuxbios.rom] Error 1 okajima@Debian:~/lx2/LinuxBIOSv2-2084/targets/via/epia-m/epia-m$ gcc -v Reading specs from /usr/lib/gcc-lib/i386-linux/2.95.4/specs gcc version 2.95.4 20011002 (Debian prerelease) okajima@Debian:~/lx2/LinuxBIOSv2-2084/targets/via/epia-m/epia-m$ as --version GNU assembler 2.12.90.0.1 20020307 Debian/GNU Linux Copyright 2002 Free Software Foundation, Inc. This program is free software; you may redistribute it under the terms of the GNU General Public License. This program has absolutely no warranty. This assembler was configured for a target of `i386-linux'. okajima@Debian:~/lx2/LinuxBIOSv2-2084/targets/via/epia-m/epia-m$

2 1

[LinuxBIOS] S2882 Memory Hang
by Matthew Simmons 04 Nov '05

04 Nov '05

I am currently trying get LinuxBios up and running on my Tyan S2882. After hard coding the apicid_base = 1 in the mptable.c I was finally able to successfully build a bios image for my system. I am using filo as the payload and the configuration of that went well. Both LinuxBios and filo are working as expected. The problem occurs when I attempt to boot the kernel. The kernel stops after the memory manager loads. There are no errors or panics. The system just locks up. I was wondering if any of you have seen this problem, or know of a work around. I am including the kernel output from the serial console. As well as a brief description of the configuration of the system. Thanks for your help, Matthew Simmons Configuration: ---------------------------------------------- Tyan S2882 2x Opteron 248 Processors 1024mb Ram (512x per processor) LinuxBIOSv2 (Revision 2084) Kernel: 2.6.12.1 with the Realtime Preempt Patch Base OS: SuSE 9.2 GCC version: 3.3.2 Serial Console Output: (Sorry for the length) ------------------------------------------------ LinuxBIOS-1.1.8_s2882_Fallback Fri Nov 4 12:47:40 CST 2005 starting... (0,1) link=01 (1,0) link=01 02 nodes initialized. SBLink=00 NC node|link=00 Ram1.00 Ram1.01 Ram2.00 Ram2.01 Ram3 Initializing memory: done Initializing memory: done Clearing initial memory region: done Ram4 Copying LinuxBIOS to ram. Jumping to LinuxBIOS. LinuxBIOS-1.1.8_s2882_Fallback Fri Nov 4 12:47:40 CST 2005 booting... Enumerating buses... APIC_CLUSTER: 0 enabled PCI_DOMAIN: 0000 enabled CPU: APIC: 10 enabled PCI: 00:19.0 [1022/1100] enabled PCI: 00:19.1 [1022/1101] enabled PCI: 00:19.2 [1022/1102] enabled PCI: 00:19.3 [1022/1103] enabled CPU: APIC: 11 enabled PCI: pci_scan_bus for bus 0 PCI: 00:18.0 [1022/1100] enabled PCI: 00:18.1 [1022/1101] enabled PCI: 00:18.2 [1022/1102] enabled PCI: 00:18.3 [1022/1103] enabled PCI: 00:19.0 [1022/1100] enabled PCI: 00:19.1 [1022/1101] enabled PCI: 00:19.2 [1022/1102] enabled PCI: 00:19.3 [1022/1103] enabled PCI: 01:00.0 [1022/7450] en PCI: 01:01.0 [1022/7450] enabled next_unitid: 0003 PCI: 01:00.0 [1022/7460] enabled PCI: 01:03.0 [1022/7460] enabled next_unitid: 0007 PCI: pci_scan_bus for bus 1 PCI: 01:01.0 [1022/7450] enabled PCI: 01:01.1 [1022/7451] enabled PCI: 01:02.0 [1022/7450] enabled PCI: 01:02.1 [1022/7451] enabled PCI: 01:03.0 [1022/7460] enabled PCI: 01:04.0 [1022/7468] enabled PCI: 01:04.1 [1022/7469] enabled PCI: 01:04.2 [1022/746a] enabled PCI: 01:04.3 [1022/746b] enabled PCI: pci_scan_bus for bus 2 Disabling static device: PCI: 0 Disabling static device: PCI: 02:06.1 PCI: 02:09.0 [14e4/1648] enabled PCI: 02:09.1 [14e4/1648] enabled PCI: pci_scan_bus returning with max=02 PCI: 02: 100MHz PCI-X PCI: pci_scan_bus for bus 3 PCI: 03:04.0 [10ee/3fc6] enabled PCI: pci_scan_bus returning with max=03 PCI: 03: Conventional PCI PCI: pci_scan_bus for bus 4 PCI: 04:00.0 [1022/7464] enabled PCI: 04:00.1 [1022/7464] enabled PCI: 04:05.0 [1095/3114] enabled PCI: 04:06.0 [1002/4752] enabled PCI: 04:08.0 [8086/1229] enabled PCI: pci_scan_bus returning with m PNP: 002e.0 enabled PNP: 002e.1 disabled PNP: 002e.2 enabled PNP: 002e.3 disabled PNP: 002e.5 enabled PNP: 002e.6 disabled PNP: 002e.7 disabled PNP: 002e.8 disabled PNP: 002e.9 disabled PNP: 002e.a disabled PNP: 002e.b enabled PCI: pci_scan_bus returning with max=04 PCI: pci_scan_bus returning with max=04 done Allocating resources... Reading resources... PCI: 01:01.0 1c <- [0x00fffff000 - 0x00ffffefff] bus 2 io PCI: 01:01.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 2 prefmem PCI: 01:02.0 1c <- [0x00fffff00 PCI: 01:02.0 24 <- [0xfffffffffff00000 - 0xffffffffffefffff] bus 3 prefmem map page: 16ee: 118 Cannot map page: 16f PCI: 01:03.0 24 <- [0x00fff00000 - 0x00ffefffff] bus 4 prefmem Cannot map pag Cannot map p Done reading resources. Cannot map pag Allocating VGA resource PCI: 04:06.0 Cannot Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 01:03.0 map page: 174xtra MTRR'sd < Setting PCI_BRIDGE_CTL_VGA for bridge PCI: 00:18.0 Cannot map Cannot map page: 176 Setting PCI_BRIDGE_CTL_VGA for bridge PCI_DOMAIN: 0000 Cannot map page: 178 page: 14b Setting PCI_BRIDGE_CTL_VGA for bridge Root Devicep page: 14c Setting resources...7a PCI: 00:18.0 1b8 <- [0x00fd400000 - 0x00fd3fffff] prefmem <node 0 link 0> Cannot map page: Cannot map page: 17d PCI: 01:02.1 10 <- [0x00fd301000 - 0x00fd301fff] mem64map page: 17 Cannot map page: 1a8 PCI: 01:03.0 1c <- [0x0000001000 - 0x0000001fff] bus 4 io page: 18 Cannot map page: 1 PCI: 01:03.0 20 <- [0x00fc000000 - 0x00fd0fffff] bus 4 memge: 191 Cannot map page: 1acnot PCI: 04:00.0 10 <- [0x00fd020000 - 0x00fd020fff] meme: 1ading f Cannot map page PCI: 04:00.1 10 <- [0x00fd021000 - 0x00fd021fff] mem Cannot map page: 1aft map PCI: 04:05.0 10 <- [0x0000001450 - 0x0000001457] ioCann Cannot map page: 1b1age: 19566e: 124M, W PCI: 04:05.0 14 <- [0x0000001470 - 0x0000001473] ioge: 1b Cannot map page: 1bcot ma PCI: 04:05.0 18 <- [0x0000001460 - 0x0000001467] ioot map page: 1bdot map Ca PCI: 04:05.0 1c <- [0x00000014 PNP: 002e.0 70 <- [0x0000000006 - 0x0000000006] irq Cannot map page: 1de Cann PNP: 002e.0 74 <- [0x0000000002 - 0x0000000002] drq P C Can -Cannot map page: 1e0t ma PNP: 002e.2 60 <- [0x00000003f8 - 0x00000003ff] ionot map page: 1e1 Cannot ma PNP: 002e.2 70 <- [0x0000000004 - 0x0000000004] irqo Cannot map page: 1e3ot map page: 1ca PNP: 002e.5 60 <- [0x0000000060 - 0x0000000060] io Cannot map page: 1f4 PNP: 002e.5 62 <- [0x0000000064 - 0x0000000064] io Cannot Cannot map page: 1f6 PNP: 002e.5 70 <- [0x0000000001 - 0x0000000001] irq: 1f7 Cannot m Cannot m PNP: 002e.5 72 <- [0x000000000c - 0x000000000c] irq Cannot map page: 1f9Cannot map PNP: 002e.b 60 <- [0x0000000290 - 0x0000000297] ioage: 1faage: 1ee Canno PNP: 002e.b 70 <- [0x0000000005 - 0x0000000005] irq Cannot map page PNP: 002e.5 init PCI: 01:01.1 cmd <- 146b i NB: Fu PCI: 01:02.0 bridge ctrl <- 0003 PCI: 01:02.0 cmd <- 1460ot ma PCI: 03:04.0 cmd <- 142.0 init PCI: 01:02.1 subsystem <- 10f1/2882 PNP: 002e.0 initd PCI: 01:02.1 cmd <- 146 tables to 0xf0000...do PCI: 01:03.0 bridge ctrl <- 000b PCI: 01:03.0 cmd <- 147ng copy of IRQ routing PCI: 04:00.0 subsystem <- 10f1/2882 PCI: 04:00.0 cmd <- 142PCI: 00:19.1 init:06.0 PCI: 04:00.1 subsystem <- 10f1/2882RQ routing table consistency...PCI: PCI: 04:00.1 cmd <- 142 PCI: 04:05.0 subsystem <- 10f1/2882 check_pirq_routing_table() - irq_ PCI: 04:05.0 cmd <- 143: 0x000f00sc Control.. PCI: 04:06.0 subsystem <- 10f1/2882 PCI: 04:06.0 cmd <- 1c3 33:stre PCI: 01:04.1 cmd <- 1410xfffe0000 - 0xfffe6fff PCI: 01:04.2 subsystem <- 10f1/2882 Found PCI: 01:04.2 cmd <- 141 PCI: 01:04.3 subsystem <- 10f1/2882 Loading Ethe PCI: 01:04.3 cmd <- 141 PCI: 00:18.1 subsystem <- 10f1/2882ing non PT_LOAD segment PCI: 00:18.1 cmd <- 140ot 5.2.6 (GPL) http://e PCI: 00:18.2 subsystem <- 10f1/2882 hda4:/boot/vmlinuz initrd=/boot/in PCI: 00:18.2 cmd <- 140ons PCI: 00:18.3 cmd <- 140 PCI: 00:19.0 cmd <- 140 PCI: 00:19.1 cmd <- 140 hda: LBA48: HDS7280 Initializing CPU #0 CPU: vendor AMD device f5aack Fri Nov 4 13:59:37 CS Enabling cache... Setting fixed MTRRs(0-88) type: UC Found Lin Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM (0,1) link=01host) # Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM 02 nodes initialized. DONE fixed MTRRsSBLink=00and lin Setting variable MTRR 0, base: 0MB, range: 1024MB, type WB ht reset -canning NU DONE variable MTRRs2_Fallback Fri Nov Clear out the extra MTRR'sng... MTRR check Fixed MTRRs : Enabled Linux version Variable MTRRs: Enabledeko@buildho Setting up local apic..=01on 3 Copying Lin Enabling cachepe 16 Setting fixed MTRRs(0-88) type: UCnuxBIOS. BIO Setting fixed MTRRs(0-16) Type: WB, RdMEM, WrMEM4 13:59:37 CST 2005 booting... Setting fixed MTRRs(24-88) Type: WB, RdMEM, WrMEM BIOS-e820: 00000000000f0000 - 000 DONE fixed MTRRs Enumeratin Setting variable MTRR 0, base: 0MB, range: 1024MB, type WB Scanning NU PCI_DOMAIN: 0000 enabl DONE variable MTRRs CPU: Clear out the extra MTRR's 0000000000 MTRR check Fixed MTRRs : Enabled/11 PCI: 00:19.1 [10 All AP CPUs stopped PCI: 00:18.0 initr #17 INVAL PCI: 01:01.0 init 00:19.2 [1022/11 PCI: 02:09.0 init PCI: 02:09.1 init#1 PCI PCI: 01:02.0 init03] enabled PCI: 01:03.0 init I PCI: PCI: 04:05.0 init] enabled00. PCI: 04:06.0 init PCI: rom address for PCI: 04:06.0 = fff80000: 0003 Incorrect Expansion ROM Header Signature 457fCI: 01:00.0 [1022/7460] enabled PCI: 04:08.0 init CPU 0: apertur PCI: 01:04.0 init01:03.0 [1022/746 RTC Initd next_u Invalid CMOS LB checksum enabling HPET @0xf PCI: 00:18.2 init PCI: 00:18.3 initstatic device: PC NB: Function 3 Misc Control.. done. Inode-cache hash table PCI: 00:19.0 init D PCI: 00:19.1 initvice: PCI: 02:06. PCI: 00:19.2 init PCI: 00:19.3 init14e4/1648] enable NB: Function 3 Misc Control.. done. PCI: 03:04.0 init PCI: 02: Devices initializedbledk data, 220k in Copying IRQ routing tables to 0xf0000...done. PCI: pci_scan_bus returning with max= Wrote the mp table end at: 00000020 - 00000214 Moving GDT to 0x500...ok Wrote linuxbios table at: 00000530 - 00000de4 checksum 9515 Welcome to elfboot, the open sourced starter. January 2002, Eric Biederman. Version 1.3 33:stream_init() - rom_stream: 0xfffe0000 - 0xfffe6fff Found ELF candiate at offset 0 Loading Etherboot version: 5.2.6 Dropping non PT_LOAD segment New segment addr 0x20000 size 0x312bd offset 0xb0 filesize 0x6c5b (cleaned up) New segment addr 0x20000 size 0x312bd offset 0xb0 filesize 0x6c5b Loading Segment: addr: 0x000000003ff90000 memsz: 0x000000000002a000 filesz: 0x0000000000006c5b Clearing Segment: addr: 0x000000003ff96c5b memsz: 0x00000000000233a5 Loading Segment: addr: 0x000000000004a000 memsz: 0x00000000000072bd filesz: 0x0000000000000000 Clearing Segment: addr: 0x000000000004a000 memsz: 0x00000000000072bd Jumping to boot code at 0x20000 ROM segment 0x0000 length 0x0000 reloc 0x00020000 CPU 2056 Mhz Etherboot 5.2.6 (GPL) http://etherboot.org Tagged ELF for [FILO] Relocating _text from: [00026c60,00052870) to [3fed43f0,3ff00000) Boot from (N)etwork (D)isk or (Q)uit? Probing pci disk...it() - ro Int BIOS-e820: 00000000000f0000 - 00000000000f0400 type 16i Nov 4 13:57:25 C Virtual Wire compatibility mode BIOS-e820: 0000000000100000 - 0000000040000000 (usable)>Product ID: S2882 <6>APIC at: 0xFEE00000hda4 con Scanning NUMA topology in Northbridge 24toppe New segment Virtual Wire compatibility mode. OEM ID: TYAN <6>Product ID: S2882 <6>APIC at: 0xFEE00000 Processor #16 15:5 APIC version 16 Processor #17 15:5 APIC version 16 Processor #17 INVALID. (Max ID: 16). I/O APIC #1 Version 17 at 0xFEC00000. I/O APIC #2 Version 17 at 0xFD300000. I/O APIC #3 Version 17 at 0xFD301000. Processors: 2 Checking aperture... CPU 0: aperture @ f8000000 size 64 MB CPU 1: aperture @ f8000000 size 64 MB Built 2 zonelists Kernel command line: ro root=/dev/hda4 console=ttyS0,115200 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 131072 bytes) time.c: Using 1.193182 MHz PIT timer. time.c: Detected 1990.814 MHz processor. Console: colour dummy device 80x25 Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Memory: 1023436k/1048576k available (2452k kernel code, 0k reserved, 942k data, 220k init)

1 0

[LinuxBIOS] Re: patch for cpu in epia-m
by Raymond Mantchala 03 Nov '05

03 Nov '05

The last digit of the value set in cpu_table ( for example 0x695) is the stepping value reported by cat /dev/cpuinfo. It refers to the release of the processor. It is adviseable to verify that the value corresponding to your cpu is set in cpu_table[]. I have several epia-m boxes some with stepping 1 and some with stepping 8. In this case, I set {X86_VENDOR_CENTAUR, 0x691 } in cpu_table[] to use the box with the cpu wich has stepping 1. Regards

2 1

[LinuxBIOS] patch for cpu in epia-m
by Anton Borisov 03 Nov '05

03 Nov '05

Those who will test EPIA-M systems - please add this string to cpu_table[] in file src/cpu/via/model_centaur/model_centaur_init.c { X86_VENDOR_CENTAUR, 0x0695 }, // VIA C3 Nehemiah This will resolve problem with "Unknown CPU" and apparently will let you boot. -- Sincerely, Anton Borisov

2 1

[LinuxBIOS] get_apicid_base unresolved?
by Greg Johnson 03 Nov '05

03 Nov '05

I'm trying to build LinuxBIOS for a tyan s2891 and am getting linuxbios_ram.o(.text+0x8e22): In function `smp_write_config_table': : undefined reference to `get_apicid_base' Has the issue with get_apicid_base not been resolved yet? Thanks, Greg

1 0

← Newer
1
2
3
4
5
6
7
8
9
Older →

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

2003

2002

coreboot November 2005