Author: rminnich Date: 2009-10-09 22:07:48 +0200 (Fri, 09 Oct 2009) New Revision: 4755
Modified: trunk/coreboot-v2/src/mainboard/dell/s1850/auto.c trunk/coreboot-v2/src/mainboard/dell/s1850/s1850_fixups.c trunk/coreboot-v2/src/southbridge/intel/i82801er/i82801er_early_smbus.c Log: This change allows us to see the spd on the s850, finally. There is an i2c mux out there. We found it using a user level program that, as usual, began by inverting all gpios until we found out what we needed to know. In the end, we just set up the GPIOs as the factory bios does.
Signed-off-by: Ronald G. Minnich rminnich@gmail.com Acked-by: Myles Watson mylesgw@gmail.com
Modified: trunk/coreboot-v2/src/mainboard/dell/s1850/auto.c =================================================================== --- trunk/coreboot-v2/src/mainboard/dell/s1850/auto.c 2009-10-09 17:40:34 UTC (rev 4754) +++ trunk/coreboot-v2/src/mainboard/dell/s1850/auto.c 2009-10-09 20:07:48 UTC (rev 4755) @@ -65,25 +65,6 @@ } static inline int spd_read_byte(unsigned device, unsigned address) { - /* fake it out for this board */ - switch(device) { - case 0x52: - case 0x53: - print_debug("FAKE"); - device = 0x50; - break; - case 0x50: - case 0x51: - case 0x54: - case 0x55: - case 0x56: - case 0x57: - print_debug("57"); - device = 0x57; - break; - default: - die("BAD DEV IN spd_read_byte"); - } return smbus_read_byte(device, address); }
@@ -278,12 +259,17 @@ w = inw(0x866); outw(w|2, 0x866);
+#if 0 + /*seriaice shows + dell does this so leave it here so I don't forget + */ /* SMBUS */ pci_write_config16(PCI_DEV(0, 0x1f, 3), 0x20, 0x08c0);
/* unknown */ b = inb(0x8c2); outb(0xdf, 0x8c2); +#endif
/* another device enable? */ b = pci_read_config8(PCI_DEV(0, 0, 0), 0xf4); @@ -314,11 +300,12 @@ uart_init(); console_init();
+ /* stuff we seem to need */ - pc8374_enable_dev(PC8374_KBCK, 0); + pc8374_enable_dev(PNP_DEV(0x2e, PC8374_KBCK), 0);
/* GPIOs */ - pc8374_enable_dev(PC8374_GPIO, 0xc20); + pc8374_enable_dev(PNP_DEV(0x2e, PC8374_GPIO), 0xc20);
/* keep this in mind. SerialICE-hlp: outb 002e <= 23 @@ -351,7 +338,7 @@ #if 1 enable_smbus(); #endif -#if 0 +#if 1 // dump_spd_registers(&cpu[0]); int i; for(i = 0; i < 1; i++) {
Modified: trunk/coreboot-v2/src/mainboard/dell/s1850/s1850_fixups.c =================================================================== --- trunk/coreboot-v2/src/mainboard/dell/s1850/s1850_fixups.c 2009-10-09 17:40:34 UTC (rev 4754) +++ trunk/coreboot-v2/src/mainboard/dell/s1850/s1850_fixups.c 2009-10-09 20:07:48 UTC (rev 4755) @@ -33,6 +33,26 @@ * we leave it enabled and visible in config space -- 8f66 */ pci_write_config16(PCI_DEV(0, 0x1f, 0), 0xf2, 0x8f66); + /* GPIOs -- needed, possibly, for SPD */ + pci_write_config32(PCI_DEV(0, 0x1f, 0), 0x58, 0x881); + pci_write_config8(PCI_DEV(0, 0x1f, 0), 0x5c, 0x10); + + /* now the fun begins ... enable the GPIOs as done on factory */ + /* factory config from IO ports + * It has a few more things enabled than default! + */ + outl(0x1ae0f183, 0x880); + outl(0x1b00ffff, 0x884); + outl(0x131f0000, 0x88c); + outl(0x00000000, 0x894); + outl(0x00040000, 0x898); + outl(0x00000000, 0x8a4); + outl(0x00000000, 0x8a8); + outl(0x000031c0, 0x8ac); + outl(0x00000007, 0x8b0); + outl(0x00000304, 0x8b4); + outl(0x00030303, 0x8b8); + }
Modified: trunk/coreboot-v2/src/southbridge/intel/i82801er/i82801er_early_smbus.c =================================================================== --- trunk/coreboot-v2/src/southbridge/intel/i82801er/i82801er_early_smbus.c 2009-10-09 17:40:34 UTC (rev 4754) +++ trunk/coreboot-v2/src/southbridge/intel/i82801er/i82801er_early_smbus.c 2009-10-09 20:07:48 UTC (rev 4755) @@ -9,6 +9,7 @@ print_spew("SMBus controller enabled\r\n");
pci_write_config32(dev, 0x20, SMBUS_IO_BASE | 1); + print_debug_hex32(pci_read_config32(dev, 0x20)); /* Set smbus enable */ pci_write_config8(dev, 0x40, 1); /* Set smbus iospace enable */