7 Oct
2009
7 Oct
'09
1:14 p.m.
I was able to get coreboot pretty much up and running with gpxe and seabios. The trick was to use the Kconfig build system instead. I still have an issue though. I was not able to build it with ACPI tables, an mp table, or a PIRQ table. If I did, I got this error:
make: *** No rule to make target `/local/coreboot-v2/src/mainboard/tyan/s2881/dsdt.dsl', needed by `/local/coreboot-v2/build/dsdt.c'. Stop.
It seems as though I need these tables as Linux is not able to load the drivers for any PCI device. Could someone help me with this? Thanks again.
--
Hugh Greenberg
Los Alamos National Laboratory, CCS-1
Email: hng@lanl.gov
Phone: (505) 665-6471
Myles Watson wrote:
>
>> -----Original Message-----
>> From: Hugh Greenberg [mailto:hng@lanl.gov]
>> Sent: Thursday, October 01, 2009 5:46 PM
>> To: Myles Watson
>> Cc: coreboot@coreboot.org
>> Subject: Re: [coreboot] tyan s2881 with seabios and gpxe
>>
>> This is all the output I get on the serial port. How can I get a full
>> log? I do not see the device number, its: 02:09.0 .
>>
> I thought you'd truncated it. It's hanging for some reason. I've never
> seen Coreboot hang there.
>
>
>> --
>> Hugh Greenberg
>> Los Alamos National Laboratory, CCS-1
>> Email: hng@lanl.gov
>> Phone: (505) 665-6471
>>
>>
>>
>> Myles Watson wrote:
>>
>>>> Thanks. I took option number 2. It flashed successfully, however,
>>>>
>> gpxe
>>
>>>> does not seem to be starting. Here is the output from the
>>>> coreboot/seabios:
>>>>
>>>>
>>>
>>>> PCI: 00:01.5: enabled 0, 0 resources
>>>> PCI: 00:01.6: enabled 0, 0 resources
>>>> PCI: 00:18.1: enabled 1, 0 resources
>>>> PCI: 00:18.2: enabled 1, 0 resources
>>>> PCI: 00:18.3: enabled 1, 0 resources
>>>> APIC_CLUSTER: 0 enabled
>>>> PCI_DOMAIN: 0000 enabled
>>>> PCI: 00:18.3 siblings=0
>>>> CPU: APIC: 00 enabled
>>>> PCI: 00:19.0 [1022/1100] enabled
>>>> PCI: 00:19.1 [1022/1101] enabled
>>>> PCI: 00:19.2 [1022/1102] enabled
>>>> PCI: 00:19.3 [1022/1103] enabled
>>>> PCI: 00:19.3 siblings=0
>>>> CPU: APIC: 01 enabled
>>>> PCI: pci_scan_bus for bus 00
>>>> PCI: 00:18.0 [1022/1100] enabled
>>>> PCI: 00:18.1 [1022/1101] enabled
>>>> PCI: 00:18.2 [1022/1102] enabled
>>>> PCI: 00:18.3 [1022/1103] enabled
>>>> PCI: 00:19.0 [1022/1100] enabled
>>>> PCI: 00:19.1 [1022/1101] enabled
>>>> PCI: 00:19.2 [1022/1102] enabled
>>>> PCI: 00:19.3 [1022/1103] enabled
>>>>
>>>> I don't see 14e4/1648 above. Is that the problem?
>>>>
>>>>
>>> It should come after this. The full log would be helpful. Do you see
>>>
>> the
>>
>>> device's PCI device number that you see in lspci? eg. PCI: 00:01.5
>>>
>
> The next thing in my log is:
>
> PCI: Using configuration type 1
>
> Do you want to try Rev 4645? 4646 was the last one that touched that code.
>
> Sorry I'm not more help.
>
> Thanks,
> Myles
>
>