Re: [coreboot] FIRST LINUX BOOT: v3 on alix1c!

[Marc Jones]

ron minnich wrote:
> On Feb 7, 2008 11:27 AM, Marc Jones  wrote:
> > You need good settings for the southbridge in your platform dts. You
> > should be able to copy these from v2.
> >
> > /* LPC IRQ polarity. Each bit is an IRQ 0-15. */
> >     lpc_serirq_polarity = "0";
> > /* 0:continuous 1:quiet */
> > lpc_serirq_mode = "0";
> >
> > /* GPIO(0-0x20) for INT D:C:B:A, 0xFF=none. See virtual PIC spec. */
> > enable_gpio_int_route = "0";
>
> Here are the current defaults (recall that the dts can set defaults)
>     constructor = "cs5536_constructors";
>     pciid = "PCI_VENDOR_ID_AMD,PCI_DEVICE_ID_AMD_CS5536_ISA";
>
>     /* Interrupt enables for LPC bus. Each bit is an IRQ 0-15. */
>     lpc_serirq_enable = "0";
>
>     /* LPC IRQ polarity. Each bit is an IRQ 0-15. */
>     lpc_serirq_polarity = "0";
>
>     /* 0:continuous 1:quiet */
>     lpc_serirq_mode = "0";
>
>     /* GPIO(0-0x20) for INT D:C:B:A, 0xFF=none. See virtual PIC spec. */
>     enable_gpio_int_route = "0";
>
>     /* 0:IDE 1:FLASH, if you are using NAND flash instead of IDE drive. */
>     enable_ide_nand_flash = "0";
>
>     /* IDE: enable CS5536 IDE. There may be a different IDE
>
> controller on board */
>         enable_ide = "0";
>     /* Enable USB Port 4 (0:host 1:device). */
>     enable_USBP4_device = "0";
>
>     /* 0:off, xxxx:overcurrent setting, e.g. 0x3FEA.
>      * See CS5536 - Data Book (pages 380-381).
>      */
>     enable_USBP4_overcurrent = "0";
>
>     /* COM1 settings */
>     com1_enable = "0";
>     com1_address = "0x3f8";
>     com1_irq = "4";
>
>     /* COM2 settings */
>     com2_enable = "0";
>     com2_address = "0x2f8";
>     com2_irq = "3";

Right, so the defaults of 0 would be bad. You need to match the v2 
mainboard config.lb for your v3 mainboard dts.
for the alixc1 it should be something like this.

southbridge {
            /config/("southbridge/amd/cs5536/dts");
            pcipath = "0xf,0";
            enabled;
            enable_ide = "1";         
            lpc_serirq_enable = "0x000010da";             /* Interrupt 
enables for LPC bus. Each bit is an IRQ 0-15. */
            lpc_serirq_polarity = "0x0000EF25";           /* LPC IRQ 
polarity. Each bit is an IRQ 0-15. */
            lpc_serirq_mode = "1";                                /* 
0:continuous 1:quiet */
            enable_gpio_int_route = "0x0D0C0700";     /* GPIO(0-0x20) 
for INT D:C:B:A, 0xFF=none. See virtual PIC spec. */
        };

Marc