Am Dienstag, den 16.09.2014, 22:21 -0400 schrieb Kevin O'Connor:
On Tue, Sep 16, 2014 at 09:45:17PM -0400, Kevin O'Connor wrote:
On Tue, Sep 16, 2014 at 11:34:51PM +0200, Paul Menzel wrote:
Am Sonntag, den 14.09.2014, 10:10 +0200 schrieb Paul Menzel:
testing the SSD Crucial m4 SSD 2.5 256 GB SATA 6 Gb/s on the Lenovo X60t, the payload SeaBIOS 1.7.5-40-g5109366 does not detect the drive.
[…] 32.705: |7f673000| WARNING - Timeout at ahci_port_setup:466! 32.705: |7f673000| AHCI/0: device not ready (tf 0x80) 33.205: |7f673000| WARNING - Timeout at ahci_port_reset:336!
Out of curiosity, what does the patch below return in the failure and success case?
Could you use the patch below instead.
Kevin, thank you for the reply. I attached your patch, rebuild SeaBIOS (the log level is set to 5) and tested it on the Lenovo X60t.
Showing that it is a timing issue, the first try, the SSD was detected correctly.
[…] 01.214: init ahci 01.214: AHCI controller at 1f.2, iobase e4444400, irq 0 01.214: AHCI: cap 0xdf12ff03, ports_impl 0x1 01.214: /7f673000\ Start thread 01.214: |7f673000| AHCI/0: probing 01.215: |7f673000| AHCI/0: link up 01.215: |7f673000| AHCI/0: device ready (tf 0x150 cmd=6016 stat=113 ctl=0 err=0) 01.215: |7f673000| AHCI/0: ... finished, status 0x51, ERROR 0x4 01.215: |7f673000| Searching bootorder for: /pci@i0cf8/*@1f,2/drive@0/disk@0 01.215: |7f673000| AHCI/0: registering: "AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes)" 01.216: |7f673000| Registering bootable: AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes) (type:2 prio:103 data:f1610) 01.215: \7f673000/ End thread […]
So powering it off and on again, it was not detected.
[…] 01.542: init ahci 01.541: AHCI controller at 1f.2, iobase e4444400, irq 0 01.541: AHCI: cap 0xdf12ff03, ports_impl 0x1 01.541: /7f673000\ Start thread 01.541: |7f673000| AHCI/0: probing 01.542: |7f673000| AHCI/0: link up […] 32.700: |7f673000| WARNING - Timeout at ahci_port_setup:466! 32.700: |7f673000| AHCI/0: device not ready (tf 0x80 cmd=6016 stat=113 ctl=0 err=4050002) 33.201: |7f673000| WARNING - Timeout at ahci_port_reset:336! 33.201: \7f673000/ End thread […]
Doing a warm reset with Ctrl + Alt + Del the SSD was detected again.
[…] 50.649: init ahci 50.649: AHCI controller at 1f.2, iobase e4444400, irq 0 50.649: AHCI: cap 0xdf12ff03, ports_impl 0x1 50.649: /7f673000\ Start thread 50.649: |7f673000| AHCI/0: probing 50.650: |7f673000| AHCI/0: link up 50.649: |7f673000| AHCI/0: device ready (tf 0x150 cmd=6016 stat=113 ctl=0 err=0) 50.650: |7f673000| AHCI/0: ... finished, status 0x51, ERROR 0x4 50.650: |7f673000| Searching bootorder for: /pci@i0cf8/*@1f,2/drive@0/disk@0 50.650: |7f673000| AHCI/0: registering: "AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes)" 50.650: |7f673000| Registering bootable: AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes) (type:2 prio:103 data:f1610) 50.650: \7f673000/ End thread […]
Please find all the logs pasted at the end of the message.
Thanks,
Paul
$ ./scripts/readserial.py /dev/ttyUSB0 115200
======= Fri Sep 19 08:59:19 2014 (adjust=86.8us) 00.000: <00> 01.047: Changing serial settings was 0/0 now 3/0 01.048: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 01.048: Attempting to find coreboot table 01.048: Found coreboot table forwarder. 01.048: Now attempting to find coreboot memory map 01.048: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 01.048: Found coreboot cbmem console @ 7f7de000 01.048: Found mainboard Lenovo ThinkPad X60 / X60s 01.048: malloc preinit 01.048: Relocating init from 0x000e6af0 to 0x7f679140 (size 44544) 01.048: malloc init 01.048: Found CBFS header at 0xfffffa50 01.048: Add romfile: cmos_layout.bin (size=1828) 01.048: Add romfile: pci8086,27a2.rom (size=65536) 01.048: Add romfile: cmos.default (size=256) 01.048: Add romfile: cpu_microcode_blob.bin (size=94208) 01.048: Add romfile: etc/ps2-keyboard-spinup (size=8) 01.048: Add romfile: config (size=4221) 01.049: Add romfile: (size=29976) 01.049: Add romfile: fallback/romstage (size=50939) 01.048: Add romfile: fallback/ramstage (size=68308) 01.048: Add romfile: fallback/payload (size=55704) 01.048: Add romfile: (size=1723864) 01.049: init ivt 01.049: init bda 01.049: init bios32 01.048: init PMM 01.048: init PNPBIOS table 01.049: init keyboard 01.049: init mouse 01.049: init pic 01.049: math cp init 01.051: CPU Mhz=1663 01.050: init timer 01.050: PCI probe 01.050: PCI device 00:00.0 (vd=8086:27a0 c=0600) 01.051: PCI device 00:02.0 (vd=8086:27a2 c=0300) 01.050: PCI device 00:02.1 (vd=8086:27a6 c=0380) 01.050: PCI device 00:1b.0 (vd=8086:27d8 c=0403) 01.051: PCI device 00:1c.0 (vd=8086:27d0 c=0604) 01.051: PCI device 00:1c.1 (vd=8086:27d2 c=0604) 01.051: PCI device 00:1c.2 (vd=8086:27d4 c=0604) 01.050: PCI device 00:1c.3 (vd=8086:27d6 c=0604) 01.051: PCI device 00:1d.0 (vd=8086:27c8 c=0c03) 01.051: PCI device 00:1d.1 (vd=8086:27c9 c=0c03) 01.051: PCI device 00:1d.2 (vd=8086:27ca c=0c03) 01.051: PCI device 00:1d.3 (vd=8086:27cb c=0c03) 01.051: PCI device 00:1d.7 (vd=8086:27cc c=0c03) 01.051: PCI device 00:1e.0 (vd=8086:2448 c=0604) 01.051: PCI device 00:1f.0 (vd=8086:27b9 c=0601) 01.051: PCI device 00:1f.1 (vd=8086:27df c=0101) 01.051: PCI device 00:1f.2 (vd=8086:27c5 c=0106) 01.051: PCI device 00:1f.3 (vd=8086:27da c=0c05) 01.051: PCI device 01:00.0 (vd=8086:109a c=0200) 01.051: PCI device 02:00.0 (vd=8086:4227 c=0280) 01.051: PCI device 05:00.0 (vd=1180:0476 c=0607) 01.051: PCI device 05:00.1 (vd=1180:0552 c=0c00) 01.051: PCI device 05:00.2 (vd=1180:0822 c=0805) 01.051: Found 23 PCI devices (max PCI bus is 06) 01.051: Relocating coreboot bios tables 01.052: Copying SMBIOS entry point from 0x7f7cc000 to 0x000f18d0 01.052: Copying ACPI RSDP from 0x7f7cd000 to 0x000f18a0 01.052: Copying MPTABLE from 0x7f7d9000/7f7d9010 to 0x000f16d0 01.052: rsdp=0x000f18a0 01.052: rsdt=0x7f7cd030 01.052: fadt=0x7f7d0510 01.052: pm_tmr_blk=508 01.052: Using pmtimer, ioport 0x508 01.052: Scan for VGA option rom 01.053: Attempting to init PCI bdf 00:02.0 (vd 8086:27a2) 01.053: Copying data 65536@0xffe007b8 to 65536@0x000c0000 01.086: Running option rom at c000:0003 01.134: unimplemented handle_155fXX:26: 01.134: a=80005f34 b=0000078f c=00000002 d=00000002 ds=0000 es=c000 ss=e000 01.134: si=00000994 di=00000080 bp=50a06e0c sp=0000ffe8 cs=c000 ip=4a6e f=0046 01.181: Turning on vga text mode console 01.212: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 01.212: Machine UUID c09ecb7b-2a1f-dc11-b88a-942d40962902 01.212: /7f677000\ Start thread 01.212: |7f677000| init usb 01.212: |7f677000| EHCI init on dev 00:1d.7 (regs=0xe4444020) 01.212: /7f675000\ Start thread 01.212: init ps2port 01.212: /7f674000\ Start thread 01.213: |7f674000| Copying data 8@0xffe27978 to 8@0x7f674fc8 01.213: /7f673000\ Start thread 01.214: init lpt 01.213: Found 0 lpt ports 01.213: init serial 01.213: Found 1 serial ports 01.213: init hard drives 01.213: ATA controller 1 at 1f0/3f4/0 (irq 14 dev f9) 01.214: /7f672000\ Start thread 01.213: /7f671000\ Start thread 01.214: ATA controller 2 at 170/374/0 (irq 15 dev f9) 01.214: /7f670000\ Start thread 01.214: |7f670000| powerup IDE floating 01.213: |7f670000| powerup IDE floating 01.213: |7f670000| powerup IDE floating 01.214: |7f670000| powerup IDE floating 01.214: \7f670000/ End thread 01.214: /7f670000\ Start thread 01.214: \7f671000/ End thread 01.214: \7f673000/ End thread 01.214: init ahci 01.214: AHCI controller at 1f.2, iobase e4444400, irq 0 01.214: AHCI: cap 0xdf12ff03, ports_impl 0x1 01.214: /7f673000\ Start thread 01.214: |7f673000| AHCI/0: probing 01.215: /7f671000\ Start thread 01.215: \7f670000/ End thread 01.215: |7f673000| AHCI/0: link up 01.215: |7f673000| AHCI/0: device ready (tf 0x150 cmd=6016 stat=113 ctl=0 err=0) 01.215: |7f672000| DVD/CD [ata0-0: DVD/CDRW UJDA775 ATAPI-5 DVD/CD] 01.215: |7f672000| Searching bootorder for: /pci@i0cf8/*@1f,1/drive@0/disk@0 01.215: |7f672000| Registering bootable: DVD/CD [ata0-0: DVD/CDRW UJDA775 ATAPI-5 DVD/CD] (type:3 prio:102 data:f1660) 01.215: \7f672000/ End thread 01.215: |7f674000| Got ps2 nak (status=51) 01.215: |7f674000| ps2 command 2ff failed (aux=0) 01.215: /7f672000\ Start thread 01.215: \7f671000/ End thread 01.215: |7f673000| AHCI/0: ... finished, status 0x51, ERROR 0x4 01.215: /7f671000\ Start thread 01.215: |7f673000| Searching bootorder for: /pci@i0cf8/*@1f,2/drive@0/disk@0 01.216: /7f670000\ Start thread 01.215: |7f673000| AHCI/0: registering: "AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes)" 01.216: |7f673000| Registering bootable: AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes) (type:2 prio:103 data:f1610) 01.215: \7f673000/ End thread 01.215: |7f674000| Got ps2 nak (status=51) 01.215: |7f674000| ps2 command 2ff failed (aux=0) 01.215: /7f673000\ Start thread 01.215: \7f670000/ End thread 01.215: \7f672000/ End thread 01.217: |7f674000| Got ps2 nak (status=51) 01.217: |7f674000| ps2 command 2ff failed (aux=0) 01.218: |7f674000| Got ps2 nak (status=51) 01.220: |7f674000| ps2 command 2ff failed (aux=0) 01.220: \7f673000/ End thread 01.222: |7f674000| Got ps2 nak (status=51) 01.222: |7f674000| ps2 command 2ff failed (aux=0) 01.224: |7f674000| Got ps2 nak (status=51) 01.225: |7f674000| ps2 command 2ff failed (aux=0) 01.226: |7f674000| Got ps2 nak (status=51) 01.227: |7f674000| ps2 command 2ff failed (aux=0) 01.228: |7f674000| Got ps2 nak (status=51) 01.229: |7f674000| ps2 command 2ff failed (aux=0) 01.229: |7f671000| set_address 0x7f676fb0 01.230: |7f677000| UHCI init on dev 00:1d.0 (io=5000) 01.230: /7f673000\ Start thread 01.230: /7f672000\ Start thread 01.230: \7f672000/ End thread 01.230: |7f671000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 01.230: |7f677000| UHCI init on dev 00:1d.1 (io=5020) 01.230: /7f672000\ Start thread 01.230: /7f670000\ Start thread 01.230: \7f670000/ End thread 01.230: /7f670000\ Start thread 01.231: \7f670000/ End thread 01.230: |7f674000| Got ps2 nak (status=51) 01.230: |7f674000| ps2 command 2ff failed (aux=0) 01.230: |7f677000| UHCI init on dev 00:1d.2 (io=5040) 01.231: /7f670000\ Start thread 01.231: /7f66f000\ Start thread 01.230: \7f66f000/ End thread 01.231: /7f66f000\ Start thread 01.231: \7f66f000/ End thread 01.231: |7f671000| config_usb: 0x7f676ad0 01.231: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=8) 01.231: |7f677000| UHCI init on dev 00:1d.3 (io=5060) 01.231: /7f66f000\ Start thread 01.231: /7f66e000\ Start thread 01.231: \7f66e000/ End thread 01.231: /7f66e000\ Start thread 01.231: \7f66e000/ End thread 01.231: \7f673000/ End thread 01.231: |7f671000| device rev=0200 cls=09 sub=00 proto=02 size=64 01.231: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=9) 01.232: \7f677000/ End thread 01.231: /7f673000\ Start thread 01.231: \7f673000/ End thread 01.231: \7f672000/ End thread 01.231: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=41) 01.231: |7f674000| Got ps2 nak (status=51) 01.231: |7f674000| ps2 command 2ff failed (aux=0) 01.232: \7f670000/ End thread 01.232: |7f671000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 01.232: \7f66f000/ End thread 01.232: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=7) 01.232: /7f673000\ Start thread 01.232: |7f673000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 01.232: |7f674000| Got ps2 nak (status=51) 01.233: |7f674000| ps2 command 2ff failed (aux=0) 01.233: /7f672000\ Start thread 01.232: /7f670000\ Start thread 01.233: |7f670000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 01.233: /7f66f000\ Start thread 01.233: |7f672000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 01.233: |7f674000| Got ps2 nak (status=51) 01.233: |7f674000| ps2 command 2ff failed (aux=0) 01.233: |7f66f000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 01.234: |7f674000| Got ps2 nak (status=51) 01.235: |7f674000| ps2 command 2ff failed (aux=0) 01.237: |7f674000| Got ps2 nak (status=51) 01.238: |7f674000| ps2 command 2ff failed (aux=0) 01.239: |7f674000| Got ps2 nak (status=51) 01.239: |7f674000| ps2 command 2ff failed (aux=0) 01.241: |7f674000| Got ps2 nak (status=51) 01.241: |7f674000| ps2 command 2ff failed (aux=0) 01.243: |7f674000| Got ps2 nak (status=51) 01.244: |7f674000| ps2 command 2ff failed (aux=0) 01.245: |7f674000| Got ps2 nak (status=51) 01.246: |7f674000| ps2 command 2ff failed (aux=0) 01.247: |7f674000| Got ps2 nak (status=51) 01.248: |7f674000| ps2 command 2ff failed (aux=0) 01.249: |7f674000| Got ps2 nak (status=51) 01.250: |7f674000| ps2 command 2ff failed (aux=0) 01.251: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.252: |7f674000| Got ps2 nak (status=51) 01.252: |7f674000| ps2 command 2ff failed (aux=0) 01.252: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.252: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.252: |7f674000| Got ps2 nak (status=51) 01.252: |7f674000| ps2 command 2ff failed (aux=0) 01.253: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.253: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.254: |7f674000| Got ps2 nak (status=51) 01.253: |7f674000| ps2 command 2ff failed (aux=0) 01.253: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.253: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.254: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.254: |7f674000| Got ps2 nak (status=51) 01.254: |7f674000| ps2 command 2ff failed (aux=0) 01.254: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.254: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.254: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.255: |7f674000| Got ps2 nak (status=51) 01.255: |7f674000| ps2 command 2ff failed (aux=0) 01.255: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.255: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.255: |7f674000| Got ps2 nak (status=51) 01.255: |7f674000| ps2 command 2ff failed (aux=0) 01.255: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.256: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.255: \7f673000/ End thread 01.256: |7f674000| Got ps2 nak (status=51) 01.256: |7f674000| ps2 command 2ff failed (aux=0) 01.256: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.257: \7f66f000/ End thread 01.256: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.256: \7f670000/ End thread 01.257: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 01.257: |7f674000| Got ps2 nak (status=51) 01.257: |7f674000| ps2 command 2ff failed (aux=0) 01.257: \7f672000/ End thread 01.258: |7f671000| Initialized USB HUB (0 ports used) 01.257: \7f671000/ End thread 01.259: |7f674000| Got ps2 nak (status=51) 01.259: |7f674000| ps2 command 2ff failed (aux=0) 01.259: \7f675000/ End thread 01.261: |7f674000| Got ps2 nak (status=51) 01.262: |7f674000| ps2 command 2ff failed (aux=0) 01.266: |7f674000| Got ps2 nak (status=51) 01.266: |7f674000| ps2 command 2ff failed (aux=0) 01.268: |7f674000| Got ps2 nak (status=51) 01.268: |7f674000| ps2 command 2ff failed (aux=0) 01.271: |7f674000| Got ps2 nak (status=51) 01.272: |7f674000| ps2 command 2ff failed (aux=0) 01.274: |7f674000| Got ps2 nak (status=51) 01.275: |7f674000| ps2 command 2ff failed (aux=0) 01.278: |7f674000| Got ps2 nak (status=51) 01.278: |7f674000| ps2 command 2ff failed (aux=0) 01.282: |7f674000| Got ps2 nak (status=51) 01.281: |7f674000| ps2 command 2ff failed (aux=0) 01.285: |7f674000| Got ps2 nak (status=51) 01.285: |7f674000| ps2 command 2ff failed (aux=0) 01.288: |7f674000| Got ps2 nak (status=51) 01.288: |7f674000| ps2 command 2ff failed (aux=0) 01.291: |7f674000| Got ps2 nak (status=51) 01.291: |7f674000| ps2 command 2ff failed (aux=0) 01.293: |7f674000| Got ps2 nak (status=51) 01.295: |7f674000| ps2 command 2ff failed (aux=0) 01.296: |7f674000| Got ps2 nak (status=51) 01.297: |7f674000| ps2 command 2ff failed (aux=0) 01.298: |7f674000| Got ps2 nak (status=51) 01.299: |7f674000| ps2 command 2ff failed (aux=0) 01.301: |7f674000| Got ps2 nak (status=51) 01.302: |7f674000| ps2 command 2ff failed (aux=0) 01.305: |7f674000| Got ps2 nak (status=51) 01.305: |7f674000| ps2 command 2ff failed (aux=0) 01.308: |7f674000| Got ps2 nak (status=51) 01.308: |7f674000| ps2 command 2ff failed (aux=0) 01.311: |7f674000| Got ps2 nak (status=51) 01.310: |7f674000| ps2 command 2ff failed (aux=0) 01.312: |7f674000| Got ps2 nak (status=51) 01.312: |7f674000| ps2 command 2ff failed (aux=0) 01.314: |7f674000| Got ps2 nak (status=51) 01.315: |7f674000| ps2 command 2ff failed (aux=0) 01.316: |7f674000| Got ps2 nak (status=51) 01.317: |7f674000| ps2 command 2ff failed (aux=0) 01.319: |7f674000| Got ps2 nak (status=51) 01.319: |7f674000| ps2 command 2ff failed (aux=0) 01.321: |7f674000| Got ps2 nak (status=51) 01.322: |7f674000| ps2 command 2ff failed (aux=0) 01.324: |7f674000| Got ps2 nak (status=51) 01.324: |7f674000| ps2 command 2ff failed (aux=0) 01.327: |7f674000| Got ps2 nak (status=51) 01.327: |7f674000| ps2 command 2ff failed (aux=0) 01.328: |7f674000| Got ps2 nak (status=51) 01.329: |7f674000| ps2 command 2ff failed (aux=0) 01.331: |7f674000| Got ps2 nak (status=51) 01.331: |7f674000| ps2 command 2ff failed (aux=0) 01.332: |7f674000| Got ps2 nak (status=51) 01.333: |7f674000| ps2 command 2ff failed (aux=0) 01.334: |7f674000| Got ps2 nak (status=51) 01.335: |7f674000| ps2 command 2ff failed (aux=0) 01.338: |7f674000| Got ps2 nak (status=51) 01.338: |7f674000| ps2 command 2ff failed (aux=0) 01.341: |7f674000| Got ps2 nak (status=51) 01.340: |7f674000| ps2 command 2ff failed (aux=0) 01.342: |7f674000| Got ps2 nak (status=51) 01.343: |7f674000| ps2 command 2ff failed (aux=0) 01.345: |7f674000| Got ps2 nak (status=51) 01.345: |7f674000| ps2 command 2ff failed (aux=0) 01.347: |7f674000| Got ps2 nak (status=51) 01.347: |7f674000| ps2 command 2ff failed (aux=0) 01.349: |7f674000| Got ps2 nak (status=51) 01.349: |7f674000| ps2 command 2ff failed (aux=0) 01.351: |7f674000| Got ps2 nak (status=51) 01.352: |7f674000| ps2 command 2ff failed (aux=0) 01.353: |7f674000| Got ps2 nak (status=51) 01.354: |7f674000| ps2 command 2ff failed (aux=0) 01.356: |7f674000| Got ps2 nak (status=51) 01.357: |7f674000| ps2 command 2ff failed (aux=0) 01.358: |7f674000| Got ps2 nak (status=51) 01.359: |7f674000| ps2 command 2ff failed (aux=0) 01.361: |7f674000| Got ps2 nak (status=51) 01.361: |7f674000| ps2 command 2ff failed (aux=0) 01.363: |7f674000| Got ps2 nak (status=51) 01.364: |7f674000| ps2 command 2ff failed (aux=0) 01.365: |7f674000| Got ps2 nak (status=51) 01.366: |7f674000| ps2 command 2ff failed (aux=0) 01.367: |7f674000| Got ps2 nak (status=51) 01.368: |7f674000| ps2 command 2ff failed (aux=0) 01.369: |7f674000| Got ps2 nak (status=51) 01.370: |7f674000| ps2 command 2ff failed (aux=0) 01.372: |7f674000| Got ps2 nak (status=51) 01.373: |7f674000| ps2 command 2ff failed (aux=0) 01.375: |7f674000| Got ps2 nak (status=51) 01.375: |7f674000| ps2 command 2ff failed (aux=0) 01.377: |7f674000| Got ps2 nak (status=51) 01.378: |7f674000| ps2 command 2ff failed (aux=0) 01.379: |7f674000| Got ps2 nak (status=51) 01.380: |7f674000| ps2 command 2ff failed (aux=0) 01.381: |7f674000| Discarding ps2 data aa (status=11) 01.993: |7f674000| PS2 keyboard initialized 01.993: \7f674000/ End thread 01.993: All threads complete. 01.993: Scan for option roms 01.993: Attempting to init PCI bdf 00:00.0 (vd 8086:27a0) 01.993: Attempting to init PCI bdf 00:02.1 (vd 8086:27a6) 01.993: Attempting to init PCI bdf 00:1b.0 (vd 8086:27d8) 01.993: Attempting to init PCI bdf 00:1c.0 (vd 8086:27d0) 01.993: Attempting to init PCI bdf 00:1c.1 (vd 8086:27d2) 01.993: Attempting to init PCI bdf 00:1c.2 (vd 8086:27d4) 01.993: Attempting to init PCI bdf 00:1c.3 (vd 8086:27d6) 01.993: Attempting to init PCI bdf 00:1d.0 (vd 8086:27c8) 01.993: Attempting to init PCI bdf 00:1d.1 (vd 8086:27c9) 01.993: Attempting to init PCI bdf 00:1d.2 (vd 8086:27ca) 01.993: Attempting to init PCI bdf 00:1d.3 (vd 8086:27cb) 01.993: Attempting to init PCI bdf 00:1d.7 (vd 8086:27cc) 01.993: Attempting to init PCI bdf 00:1e.0 (vd 8086:2448) 01.993: Attempting to init PCI bdf 00:1f.0 (vd 8086:27b9) 01.993: Attempting to init PCI bdf 00:1f.2 (vd 8086:27c5) 01.993: Attempting to init PCI bdf 00:1f.3 (vd 8086:27da) 01.994: Attempting to init PCI bdf 01:00.0 (vd 8086:109a) 01.994: Attempting to init PCI bdf 02:00.0 (vd 8086:4227) 01.994: Attempting to init PCI bdf 05:00.0 (vd 1180:0476) 01.993: Attempting to init PCI bdf 05:00.1 (vd 1180:0552) 01.994: Attempting to init PCI bdf 05:00.2 (vd 1180:0822) 01.993: 01.993: Press F12 for boot menu. 01.994: 01.994: Checking for bootsplash 04.525: Searching bootorder for: HALT 04.524: Mapping cd drive 0x000f1660 04.525: Mapping hd drive 0x000f1610 to 0 04.524: drive 0x000f1610: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 s=500118192 04.525: finalize PMM 04.525: malloc finalize 04.525: Space available for UMB: cf000-ee800, f0000-f15e0 04.525: Returned 253952 bytes of ZoneHigh 04.525: e820 map has 6 items: 04.525: 0: 0000000000000000 - 000000000009fc00 = 1 RAM 04.525: 1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED 04.525: 2: 00000000000f0000 - 0000000000100000 = 2 RESERVED 04.525: 3: 0000000000100000 - 000000007f6c2000 = 1 RAM 04.525: 4: 000000007f6c2000 - 0000000080000000 = 2 RESERVED 04.525: 5: 00000000f0000000 - 00000000f4000000 = 2 RESERVED 04.525: Jump to int19 04.526: enter handle_19: 04.526: NULL 04.525: Booting from DVD/CD... 04.526: Device reports MEDIUM NOT PRESENT 04.527: scsi_is_ready returned -1 04.527: Boot failed: Could not read from CDROM (code 0003) 04.527: enter handle_18: 04.527: NULL 04.527: Booting from Hard Disk... 04.527: Booting from 0000:7c00 ^C paul@mattotaupa:~/src/seabios(master) $ ./scripts/readserial.py /dev/ttyUSB0 115200
======= Fri Sep 19 09:00:25 2014 (adjust=86.8us) 00.000: <00> 01.375: Changing serial settings was 0/0 now 3/0 01.375: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 01.375: Attempting to find coreboot table 01.376: Found coreboot table forwarder. 01.376: Now attempting to find coreboot memory map 01.376: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 01.375: Found coreboot cbmem console @ 7f7de000 01.375: Found mainboard Lenovo ThinkPad X60 / X60s 01.375: malloc preinit 01.375: Relocating init from 0x000e6af0 to 0x7f679140 (size 44544) 01.375: malloc init 01.375: Found CBFS header at 0xfffffa50 01.375: Add romfile: cmos_layout.bin (size=1828) 01.375: Add romfile: pci8086,27a2.rom (size=65536) 01.375: Add romfile: cmos.default (size=256) 01.376: Add romfile: cpu_microcode_blob.bin (size=94208) 01.376: Add romfile: etc/ps2-keyboard-spinup (size=8) 01.375: Add romfile: config (size=4221) 01.376: Add romfile: (size=29976) 01.376: Add romfile: fallback/romstage (size=50939) 01.376: Add romfile: fallback/ramstage (size=68308) 01.376: Add romfile: fallback/payload (size=55704) 01.376: Add romfile: (size=1723864) 01.376: init ivt 01.376: init bda 01.376: init bios32 01.376: init PMM 01.376: init PNPBIOS table 01.376: init keyboard 01.377: init mouse 01.377: init pic 01.377: math cp init 01.377: CPU Mhz=1664 01.378: init timer 01.378: PCI probe 01.378: PCI device 00:00.0 (vd=8086:27a0 c=0600) 01.378: PCI device 00:02.0 (vd=8086:27a2 c=0300) 01.378: PCI device 00:02.1 (vd=8086:27a6 c=0380) 01.378: PCI device 00:1b.0 (vd=8086:27d8 c=0403) 01.378: PCI device 00:1c.0 (vd=8086:27d0 c=0604) 01.378: PCI device 00:1c.1 (vd=8086:27d2 c=0604) 01.378: PCI device 00:1c.2 (vd=8086:27d4 c=0604) 01.378: PCI device 00:1c.3 (vd=8086:27d6 c=0604) 01.378: PCI device 00:1d.0 (vd=8086:27c8 c=0c03) 01.378: PCI device 00:1d.1 (vd=8086:27c9 c=0c03) 01.379: PCI device 00:1d.2 (vd=8086:27ca c=0c03) 01.378: PCI device 00:1d.3 (vd=8086:27cb c=0c03) 01.378: PCI device 00:1d.7 (vd=8086:27cc c=0c03) 01.378: PCI device 00:1e.0 (vd=8086:2448 c=0604) 01.378: PCI device 00:1f.0 (vd=8086:27b9 c=0601) 01.378: PCI device 00:1f.1 (vd=8086:27df c=0101) 01.378: PCI device 00:1f.2 (vd=8086:27c5 c=0106) 01.378: PCI device 00:1f.3 (vd=8086:27da c=0c05) 01.378: PCI device 01:00.0 (vd=8086:109a c=0200) 01.378: PCI device 02:00.0 (vd=8086:4227 c=0280) 01.378: PCI device 05:00.0 (vd=1180:0476 c=0607) 01.378: PCI device 05:00.1 (vd=1180:0552 c=0c00) 01.378: PCI device 05:00.2 (vd=1180:0822 c=0805) 01.378: Found 23 PCI devices (max PCI bus is 06) 01.379: Relocating coreboot bios tables 01.380: Copying SMBIOS entry point from 0x7f7cc000 to 0x000f18d0 01.379: Copying ACPI RSDP from 0x7f7cd000 to 0x000f18a0 01.380: Copying MPTABLE from 0x7f7d9000/7f7d9010 to 0x000f16d0 01.380: rsdp=0x000f18a0 01.380: rsdt=0x7f7cd030 01.380: fadt=0x7f7d0510 01.380: pm_tmr_blk=508 01.380: Using pmtimer, ioport 0x508 01.380: Scan for VGA option rom 01.380: Attempting to init PCI bdf 00:02.0 (vd 8086:27a2) 01.380: Copying data 65536@0xffe007b8 to 65536@0x000c0000 01.413: Running option rom at c000:0003 01.460: unimplemented handle_155fXX:26: 01.461: a=80005f34 b=0000078f c=00000002 d=00000002 ds=0000 es=c000 ss=e000 01.461: si=00000994 di=00000080 bp=50a06e0c sp=0000ffe8 cs=c000 ip=4a6e f=0046 01.507: Turning on vga text mode console 01.539: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 01.539: Machine UUID c09ecb7b-2a1f-dc11-b88a-942d40962902 01.539: /7f677000\ Start thread 01.539: |7f677000| init usb 01.539: |7f677000| EHCI init on dev 00:1d.7 (regs=0xe4444020) 01.539: /7f675000\ Start thread 01.539: init ps2port 01.540: /7f674000\ Start thread 01.540: |7f674000| Copying data 8@0xffe27978 to 8@0x7f674fc8 01.541: /7f673000\ Start thread 01.541: init lpt 01.541: Found 0 lpt ports 01.541: init serial 01.541: Found 1 serial ports 01.541: init hard drives 01.541: ATA controller 1 at 1f0/3f4/0 (irq 14 dev f9) 01.541: /7f672000\ Start thread 01.541: /7f671000\ Start thread 01.542: ATA controller 2 at 170/374/0 (irq 15 dev f9) 01.541: /7f670000\ Start thread 01.541: |7f670000| powerup IDE floating 01.541: |7f670000| powerup IDE floating 01.541: |7f670000| powerup IDE floating 01.541: |7f670000| powerup IDE floating 01.541: \7f670000/ End thread 01.541: /7f670000\ Start thread 01.542: \7f671000/ End thread 01.541: \7f673000/ End thread 01.542: init ahci 01.541: AHCI controller at 1f.2, iobase e4444400, irq 0 01.541: AHCI: cap 0xdf12ff03, ports_impl 0x1 01.541: /7f673000\ Start thread 01.541: |7f673000| AHCI/0: probing 01.542: /7f671000\ Start thread 01.542: |7f673000| AHCI/0: link up 01.542: |7f672000| DVD/CD [ata0-0: DVD/CDRW UJDA775 ATAPI-5 DVD/CD] 01.542: |7f672000| Searching bootorder for: /pci@i0cf8/*@1f,1/drive@0/disk@0 01.543: |7f672000| Registering bootable: DVD/CD [ata0-0: DVD/CDRW UJDA775 ATAPI-5 DVD/CD] (type:3 prio:102 data:f1660) 01.542: \7f672000/ End thread 01.542: |7f674000| Got ps2 nak (status=51) 01.542: |7f674000| ps2 command 2ff failed (aux=0) 01.542: /7f672000\ Start thread 01.542: \7f671000/ End thread 01.542: \7f670000/ End thread 01.542: /7f671000\ Start thread 01.542: /7f670000\ Start thread 01.543: |7f674000| Got ps2 nak (status=51) 01.543: |7f674000| ps2 command 2ff failed (aux=0) 01.543: /7f66f000\ Start thread 01.544: \7f672000/ End thread 01.545: |7f674000| Got ps2 nak (status=51) 01.545: |7f674000| ps2 command 2ff failed (aux=0) 01.545: \7f670000/ End thread 01.548: |7f674000| Got ps2 nak (status=51) 01.548: |7f674000| ps2 command 2ff failed (aux=0) 01.548: \7f66f000/ End thread 01.548: |7f674000| Got ps2 nak (status=51) 01.549: |7f674000| ps2 command 2ff failed (aux=0) 01.551: |7f674000| Got ps2 nak (status=51) 01.551: |7f674000| ps2 command 2ff failed (aux=0) 01.554: |7f674000| Got ps2 nak (status=51) 01.554: |7f674000| ps2 command 2ff failed (aux=0) 01.555: |7f674000| Got ps2 nak (status=51) 01.555: |7f674000| ps2 command 2ff failed (aux=0) 01.557: |7f674000| Got ps2 nak (status=51) 01.558: |7f674000| ps2 command 2ff failed (aux=0) 01.560: |7f674000| Got ps2 nak (status=51) 01.560: |7f674000| ps2 command 2ff failed (aux=0) 01.560: |7f671000| set_address 0x7f676fb0 01.560: |7f677000| UHCI init on dev 00:1d.0 (io=5000) 01.560: /7f672000\ Start thread 01.560: /7f670000\ Start thread 01.560: \7f670000/ End thread 01.560: |7f671000| ehci_control 0x7f676350 (dir=0 cmd=8 data=0) 01.560: |7f677000| UHCI init on dev 00:1d.1 (io=5020) 01.560: /7f670000\ Start thread 01.560: /7f66f000\ Start thread 01.560: \7f66f000/ End thread 01.560: /7f66f000\ Start thread 01.560: \7f66f000/ End thread 01.560: |7f674000| Got ps2 nak (status=51) 01.561: |7f674000| ps2 command 2ff failed (aux=0) 01.561: |7f677000| UHCI init on dev 00:1d.2 (io=5040) 01.561: /7f66f000\ Start thread 01.561: /7f66e000\ Start thread 01.561: \7f66e000/ End thread 01.561: /7f66e000\ Start thread 01.561: \7f66e000/ End thread 01.561: |7f671000| config_usb: 0x7f676350 01.561: |7f671000| ehci_control 0x7f676350 (dir=128 cmd=8 data=8) 01.561: |7f677000| UHCI init on dev 00:1d.3 (io=5060) 01.561: /7f66d000\ Start thread 01.561: /7f66c000\ Start thread 01.561: \7f66c000/ End thread 01.561: /7f66c000\ Start thread 01.561: \7f66c000/ End thread 01.561: \7f672000/ End thread 01.562: |7f671000| device rev=0200 cls=09 sub=00 proto=02 size=64 01.561: |7f671000| ehci_control 0x7f676350 (dir=128 cmd=8 data=9) 01.561: \7f677000/ End thread 01.561: /7f66c000\ Start thread 01.561: \7f66c000/ End thread 01.561: \7f670000/ End thread 01.562: |7f671000| ehci_control 0x7f676350 (dir=128 cmd=8 data=41) 01.561: |7f674000| Got ps2 nak (status=51) 01.561: |7f674000| ps2 command 2ff failed (aux=0) 01.562: \7f66f000/ End thread 01.562: |7f671000| ehci_control 0x7f676350 (dir=0 cmd=8 data=0) 01.562: \7f66d000/ End thread 01.562: |7f671000| ehci_control 0x7f676350 (dir=128 cmd=8 data=7) 01.562: /7f672000\ Start thread 01.562: |7f672000| ehci_control 0x7f676350 (dir=0 cmd=8 data=0) 01.563: |7f674000| Got ps2 nak (status=51) 01.562: |7f674000| ps2 command 2ff failed (aux=0) 01.564: /7f670000\ Start thread 01.564: /7f66f000\ Start thread 01.564: |7f66f000| ehci_control 0x7f676350 (dir=0 cmd=8 data=0) 01.563: /7f66e000\ Start thread 01.563: |7f670000| ehci_control 0x7f676350 (dir=0 cmd=8 data=0) 01.563: |7f674000| Got ps2 nak (status=51) 01.564: |7f674000| ps2 command 2ff failed (aux=0) 01.564: |7f66e000| ehci_control 0x7f676350 (dir=0 cmd=8 data=0) 01.565: |7f674000| Got ps2 nak (status=51) 01.565: |7f674000| ps2 command 2ff failed (aux=0) 01.566: |7f674000| Got ps2 nak (status=51) 01.567: |7f674000| ps2 command 2ff failed (aux=0) 01.568: |7f674000| Got ps2 nak (status=51) 01.570: |7f674000| ps2 command 2ff failed (aux=0) 01.572: |7f674000| Got ps2 nak (status=51) 01.573: |7f674000| ps2 command 2ff failed (aux=0) 01.575: |7f674000| Got ps2 nak (status=51) 01.575: |7f674000| ps2 command 2ff failed (aux=0) 01.576: |7f674000| Got ps2 nak (status=51) 01.577: |7f674000| ps2 command 2ff failed (aux=0) 01.578: |7f674000| Got ps2 nak (status=51) 01.579: |7f674000| ps2 command 2ff failed (aux=0) 01.580: |7f674000| Got ps2 nak (status=51) 01.581: |7f674000| ps2 command 2ff failed (aux=0) 01.581: |7f672000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.582: |7f674000| Got ps2 nak (status=51) 01.582: |7f674000| ps2 command 2ff failed (aux=0) 01.583: |7f66f000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.583: |7f672000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.583: |7f674000| Got ps2 nak (status=51) 01.583: |7f674000| ps2 command 2ff failed (aux=0) 01.584: |7f66e000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.584: |7f66f000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.584: |7f674000| Got ps2 nak (status=51) 01.584: |7f674000| ps2 command 2ff failed (aux=0) 01.584: |7f670000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.585: |7f672000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.584: |7f66e000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.584: |7f674000| Got ps2 nak (status=51) 01.584: |7f674000| ps2 command 2ff failed (aux=0) 01.584: |7f66f000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.585: |7f670000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.585: |7f672000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.585: |7f674000| Got ps2 nak (status=51) 01.586: |7f674000| ps2 command 2ff failed (aux=0) 01.586: |7f66e000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.586: |7f66f000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.587: |7f674000| Got ps2 nak (status=51) 01.586: |7f674000| ps2 command 2ff failed (aux=0) 01.586: |7f670000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.587: |7f672000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.587: \7f672000/ End thread 01.587: |7f674000| Got ps2 nak (status=51) 01.587: |7f674000| ps2 command 2ff failed (aux=0) 01.587: |7f66e000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.588: \7f66e000/ End thread 01.587: |7f66f000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.588: \7f66f000/ End thread 01.588: |7f670000| ehci_control 0x7f676350 (dir=128 cmd=8 data=4) 01.588: |7f674000| Got ps2 nak (status=51) 01.588: |7f674000| ps2 command 2ff failed (aux=0) 01.588: \7f670000/ End thread 01.588: |7f671000| Initialized USB HUB (0 ports used) 01.589: \7f671000/ End thread 01.590: |7f674000| Got ps2 nak (status=51) 01.591: |7f674000| ps2 command 2ff failed (aux=0) 01.591: \7f675000/ End thread 01.592: |7f674000| Got ps2 nak (status=51) 01.593: |7f674000| ps2 command 2ff failed (aux=0) 01.596: |7f674000| Got ps2 nak (status=51) 01.597: |7f674000| ps2 command 2ff failed (aux=0) 01.600: |7f674000| Got ps2 nak (status=51) 01.601: |7f674000| ps2 command 2ff failed (aux=0) 01.604: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.660: |7f674000| ps2 command 2ff failed (aux=0) 01.660: |7f674000| Got ps2 nak (status=51) 01.661: |7f674000| ps2 command 2ff failed (aux=0) 01.662: |7f674000| Got ps2 nak (status=51) 01.663: |7f674000| ps2 command 2ff failed (aux=0) 01.665: |7f674000| Got ps2 nak (status=51) 01.665: |7f674000| ps2 command 2ff failed (aux=0) 01.667: |7f674000| Got ps2 nak (status=51) 01.667: |7f674000| ps2 command 2ff failed (aux=0) 01.669: |7f674000| Got ps2 nak (status=51) 01.670: |7f674000| ps2 command 2ff failed (aux=0) 01.671: |7f674000| Got ps2 nak (status=51) 01.672: |7f674000| ps2 command 2ff failed (aux=0) 01.674: |7f674000| Got ps2 nak (status=51) 01.674: |7f674000| ps2 command 2ff failed (aux=0) 01.677: |7f674000| Got ps2 nak (status=51) 01.677: |7f674000| ps2 command 2ff failed (aux=0) 01.680: |7f674000| Got ps2 nak (status=51) 01.681: |7f674000| ps2 command 2ff failed (aux=0) 01.682: |7f674000| Got ps2 nak (status=51) 01.683: |7f674000| ps2 command 2ff failed (aux=0) 01.684: |7f674000| Got ps2 nak (status=51) 01.685: |7f674000| ps2 command 2ff failed (aux=0) 01.686: |7f674000| Got ps2 nak (status=51) 01.687: |7f674000| ps2 command 2ff failed (aux=0) 01.689: |7f674000| Got ps2 nak (status=51) 01.689: |7f674000| ps2 command 2ff failed (aux=0) 01.692: |7f674000| Got ps2 nak (status=51) 01.692: |7f674000| ps2 command 2ff failed (aux=0) 01.695: |7f674000| Got ps2 nak (status=51) 01.695: |7f674000| ps2 command 2ff failed (aux=0) 01.697: |7f674000| Got ps2 nak (status=51) 01.697: |7f674000| ps2 command 2ff failed (aux=0) 01.699: |7f674000| Got ps2 nak (status=51) 01.700: |7f674000| ps2 command 2ff failed (aux=0) 01.701: |7f674000| Got ps2 nak (status=51) 01.702: |7f674000| ps2 command 2ff failed (aux=0) 01.703: |7f674000| Got ps2 nak (status=51) 01.704: |7f674000| ps2 command 2ff failed (aux=0) 01.705: |7f674000| Got ps2 nak (status=51) 01.706: |7f674000| ps2 command 2ff failed (aux=0) 01.708: |7f674000| Got ps2 nak (status=51) 01.709: |7f674000| ps2 command 2ff failed (aux=0) 01.710: |7f674000| Got ps2 nak (status=51) 01.711: |7f674000| ps2 command 2ff failed (aux=0) 01.712: |7f674000| Got ps2 nak (status=51) 01.713: |7f674000| ps2 command 2ff failed (aux=0) 01.715: |7f674000| Got ps2 nak (status=51) 01.715: |7f674000| ps2 command 2ff failed (aux=0) 01.716: |7f674000| Got ps2 nak (status=51) 01.717: |7f674000| ps2 command 2ff failed (aux=0) 01.719: |7f674000| Got ps2 nak (status=51) 01.720: |7f674000| ps2 command 2ff failed (aux=0) 01.721: |7f674000| Discarding ps2 data aa (status=13) 02.334: |7f674000| PS2 keyboard initialized 02.334: \7f674000/ End thread 32.700: |7f673000| WARNING - Timeout at ahci_port_setup:466! 32.700: |7f673000| AHCI/0: device not ready (tf 0x80 cmd=6016 stat=113 ctl=0 err=4050002) 33.201: |7f673000| WARNING - Timeout at ahci_port_reset:336! 33.201: \7f673000/ End thread 33.201: All threads complete. 33.201: Scan for option roms 33.201: Attempting to init PCI bdf 00:00.0 (vd 8086:27a0) 33.201: Attempting to init PCI bdf 00:02.1 (vd 8086:27a6) 33.201: Attempting to init PCI bdf 00:1b.0 (vd 8086:27d8) 33.201: Attempting to init PCI bdf 00:1c.0 (vd 8086:27d0) 33.201: Attempting to init PCI bdf 00:1c.1 (vd 8086:27d2) 33.201: Attempting to init PCI bdf 00:1c.2 (vd 8086:27d4) 33.201: Attempting to init PCI bdf 00:1c.3 (vd 8086:27d6) 33.201: Attempting to init PCI bdf 00:1d.0 (vd 8086:27c8) 33.201: Attempting to init PCI bdf 00:1d.1 (vd 8086:27c9) 33.201: Attempting to init PCI bdf 00:1d.2 (vd 8086:27ca) 33.201: Attempting to init PCI bdf 00:1d.3 (vd 8086:27cb) 33.201: Attempting to init PCI bdf 00:1d.7 (vd 8086:27cc) 33.201: Attempting to init PCI bdf 00:1e.0 (vd 8086:2448) 33.201: Attempting to init PCI bdf 00:1f.0 (vd 8086:27b9) 33.201: Attempting to init PCI bdf 00:1f.2 (vd 8086:27c5) 33.201: Attempting to init PCI bdf 00:1f.3 (vd 8086:27da) 33.201: Attempting to init PCI bdf 01:00.0 (vd 8086:109a) 33.201: Attempting to init PCI bdf 02:00.0 (vd 8086:4227) 33.201: Attempting to init PCI bdf 05:00.0 (vd 1180:0476) 33.201: Attempting to init PCI bdf 05:00.1 (vd 1180:0552) 33.201: Attempting to init PCI bdf 05:00.2 (vd 1180:0822) 33.200: 33.200: Press F12 for boot menu. 33.201: 33.201: Checking for bootsplash 35.766: Searching bootorder for: HALT 35.767: Mapping cd drive 0x000f1660 35.767: finalize PMM 35.766: malloc finalize 35.767: Space available for UMB: cf000-ee800, f0000-f1630 35.767: Returned 262144 bytes of ZoneHigh 35.767: e820 map has 6 items: 35.767: 0: 0000000000000000 - 000000000009fc00 = 1 RAM 35.767: 1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED 35.767: 2: 00000000000f0000 - 0000000000100000 = 2 RESERVED 35.767: 3: 0000000000100000 - 000000007f6c4000 = 1 RAM 35.767: 4: 000000007f6c4000 - 0000000080000000 = 2 RESERVED 35.767: 5: 00000000f0000000 - 00000000f4000000 = 2 RESERVED 35.767: Jump to int19 35.768: enter handle_19: 35.767: NULL 35.767: Booting from DVD/CD... 35.768: Device reports MEDIUM NOT PRESENT 35.769: scsi_is_ready returned -1 35.769: Boot failed: Could not read from CDROM (code 0003) 35.769: enter handle_18: 35.769: NULL 35.769: Booting from Floppy... 35.770: invalid handle_legacy_disk:696: 35.769: a=00000201 b=00000000 c=00000001 d=00000000 ds=0000 es=07c0 ss=e000 35.769: si=00000000 di=00000000 bp=00000000 sp=0000ffe8 cs=f000 ip=d066 f=0202 35.769: Boot failed: could not read the boot disk 35.769: 35.769: enter handle_18: 35.769: NULL 35.769: Booting from Hard Disk... 35.769: invalid handle_legacy_disk:696: 35.769: a=00000201 b=00000000 c=00000001 d=00000080 ds=0000 es=07c0 ss=e000 35.769: si=00000000 di=00000000 bp=00000000 sp=0000ffe8 cs=f000 ip=d066 f=0202 35.769: Boot failed: could not read the boot disk 35.769: 35.769: enter handle_18: 35.769: NULL 35.769: No bootable device. Retrying in 60 seconds. 49.082: In resume (status=0) 49.082: In 32bit resume 49.082: Attempting a hard reboot 49.308: <00> 49.748: <00> 50.483: Changing serial settings was 0/0 now 3/0 50.483: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 50.483: Attempting to find coreboot table 50.484: Found coreboot table forwarder. 50.484: Now attempting to find coreboot memory map 50.484: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 50.483: Found coreboot cbmem console @ 7f7de000 50.483: Found mainboard Lenovo ThinkPad X60 / X60s 50.483: malloc preinit 50.483: Relocating init from 0x000e6af0 to 0x7f679140 (size 44544) 50.483: malloc init 50.483: Found CBFS header at 0xfffffa50 50.483: Add romfile: cmos_layout.bin (size=1828) 50.483: Add romfile: pci8086,27a2.rom (size=65536) 50.483: Add romfile: cmos.default (size=256) 50.483: Add romfile: cpu_microcode_blob.bin (size=94208) 50.483: Add romfile: etc/ps2-keyboard-spinup (size=8) 50.483: Add romfile: config (size=4221) 50.483: Add romfile: (size=29976) 50.483: Add romfile: fallback/romstage (size=50939) 50.483: Add romfile: fallback/ramstage (size=68308) 50.483: Add romfile: fallback/payload (size=55704) 50.484: Add romfile: (size=1723864) 50.483: init ivt 50.483: init bda 50.484: init bios32 50.484: init PMM 50.484: init PNPBIOS table 50.484: init keyboard 50.484: init mouse 50.484: init pic 50.484: math cp init 50.485: CPU Mhz=1665 50.485: init timer 50.486: PCI probe 50.485: PCI device 00:00.0 (vd=8086:27a0 c=0600) 50.485: PCI device 00:02.0 (vd=8086:27a2 c=0300) 50.485: PCI device 00:02.1 (vd=8086:27a6 c=0380) 50.486: PCI device 00:1b.0 (vd=8086:27d8 c=0403) 50.486: PCI device 00:1c.0 (vd=8086:27d0 c=0604) 50.486: PCI device 00:1c.1 (vd=8086:27d2 c=0604) 50.486: PCI device 00:1c.2 (vd=8086:27d4 c=0604) 50.486: PCI device 00:1c.3 (vd=8086:27d6 c=0604) 50.486: PCI device 00:1d.0 (vd=8086:27c8 c=0c03) 50.486: PCI device 00:1d.1 (vd=8086:27c9 c=0c03) 50.486: PCI device 00:1d.2 (vd=8086:27ca c=0c03) 50.486: PCI device 00:1d.3 (vd=8086:27cb c=0c03) 50.486: PCI device 00:1d.7 (vd=8086:27cc c=0c03) 50.486: PCI device 00:1e.0 (vd=8086:2448 c=0604) 50.486: PCI device 00:1f.0 (vd=8086:27b9 c=0601) 50.486: PCI device 00:1f.1 (vd=8086:27df c=0101) 50.486: PCI device 00:1f.2 (vd=8086:27c5 c=0106) 50.486: PCI device 00:1f.3 (vd=8086:27da c=0c05) 50.486: PCI device 01:00.0 (vd=8086:109a c=0200) 50.486: PCI device 02:00.0 (vd=8086:4227 c=0280) 50.486: PCI device 05:00.0 (vd=1180:0476 c=0607) 50.486: PCI device 05:00.1 (vd=1180:0552 c=0c00) 50.486: PCI device 05:00.2 (vd=1180:0822 c=0805) 50.486: Found 23 PCI devices (max PCI bus is 06) 50.486: Relocating coreboot bios tables 50.487: Copying SMBIOS entry point from 0x7f7cc000 to 0x000f18d0 50.487: Copying ACPI RSDP from 0x7f7cd000 to 0x000f18a0 50.487: Copying MPTABLE from 0x7f7d9000/7f7d9010 to 0x000f16d0 50.488: rsdp=0x000f18a0 50.488: rsdt=0x7f7cd030 50.488: fadt=0x7f7d0510 50.488: pm_tmr_blk=508 50.488: Using pmtimer, ioport 0x508 50.488: Scan for VGA option rom 50.488: Attempting to init PCI bdf 00:02.0 (vd 8086:27a2) 50.488: Copying data 65536@0xffe007b8 to 65536@0x000c0000 50.522: Running option rom at c000:0003 50.568: unimplemented handle_155fXX:26: 50.568: a=80005f34 b=0000078f c=00000002 d=00000002 ds=0000 es=c000 ss=e000 50.569: si=00000994 di=00000080 bp=50a06e0c sp=0000ffe8 cs=c000 ip=4a6e f=0046 50.615: Turning on vga text mode console 50.646: SeaBIOS (version rel-1.7.5-41-g4c32a80-20140919_084257-lenovo-x60t) 50.647: Machine UUID c09ecb7b-2a1f-dc11-b88a-942d40962902 50.647: /7f677000\ Start thread 50.647: |7f677000| init usb 50.647: |7f677000| EHCI init on dev 00:1d.7 (regs=0xe4444020) 50.647: /7f675000\ Start thread 50.647: init ps2port 50.647: /7f674000\ Start thread 50.648: |7f674000| Copying data 8@0xffe27978 to 8@0x7f674fc8 50.648: /7f673000\ Start thread 50.648: init lpt 50.648: Found 0 lpt ports 50.648: init serial 50.648: Found 1 serial ports 50.648: init hard drives 50.648: ATA controller 1 at 1f0/3f4/0 (irq 14 dev f9) 50.649: /7f672000\ Start thread 50.649: /7f671000\ Start thread 50.649: ATA controller 2 at 170/374/0 (irq 15 dev f9) 50.648: /7f670000\ Start thread 50.648: |7f670000| powerup IDE floating 50.648: |7f670000| powerup IDE floating 50.648: |7f670000| powerup IDE floating 50.648: |7f670000| powerup IDE floating 50.648: \7f670000/ End thread 50.649: /7f670000\ Start thread 50.649: \7f671000/ End thread 50.649: \7f673000/ End thread 50.649: init ahci 50.649: AHCI controller at 1f.2, iobase e4444400, irq 0 50.649: AHCI: cap 0xdf12ff03, ports_impl 0x1 50.649: /7f673000\ Start thread 50.649: |7f673000| AHCI/0: probing 50.650: /7f671000\ Start thread 50.650: \7f670000/ End thread 50.650: |7f673000| AHCI/0: link up 50.649: |7f673000| AHCI/0: device ready (tf 0x150 cmd=6016 stat=113 ctl=0 err=0) 50.649: |7f672000| DVD/CD [ata0-0: DVD/CDRW UJDA775 ATAPI-5 DVD/CD] 50.650: |7f672000| Searching bootorder for: /pci@i0cf8/*@1f,1/drive@0/disk@0 50.649: |7f672000| Registering bootable: DVD/CD [ata0-0: DVD/CDRW UJDA775 ATAPI-5 DVD/CD] (type:3 prio:102 data:f1660) 50.650: \7f672000/ End thread 50.650: /7f672000\ Start thread 50.650: \7f671000/ End thread 50.650: |7f673000| AHCI/0: ... finished, status 0x51, ERROR 0x4 50.649: /7f671000\ Start thread 50.650: |7f673000| Searching bootorder for: /pci@i0cf8/*@1f,2/drive@0/disk@0 50.650: /7f670000\ Start thread 50.650: |7f673000| AHCI/0: registering: "AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes)" 50.650: |7f673000| Registering bootable: AHCI/0: M4-CT256M4SSD2 ATA-9 Hard-Disk (238 GiBytes) (type:2 prio:103 data:f1610) 50.650: \7f673000/ End thread 50.650: /7f673000\ Start thread 50.650: \7f670000/ End thread 50.650: \7f672000/ End thread 50.665: \7f673000/ End thread 50.698: |7f671000| set_address 0x7f676fb0 50.698: |7f677000| UHCI init on dev 00:1d.0 (io=5000) 50.698: /7f673000\ Start thread 50.698: /7f672000\ Start thread 50.698: \7f672000/ End thread 50.698: |7f671000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 50.698: |7f677000| UHCI init on dev 00:1d.1 (io=5020) 50.698: /7f672000\ Start thread 50.698: /7f670000\ Start thread 50.698: \7f670000/ End thread 50.698: /7f670000\ Start thread 50.698: \7f670000/ End thread 50.698: |7f677000| UHCI init on dev 00:1d.2 (io=5040) 50.698: /7f670000\ Start thread 50.698: /7f66f000\ Start thread 50.698: \7f66f000/ End thread 50.698: /7f66f000\ Start thread 50.698: \7f66f000/ End thread 50.698: |7f671000| config_usb: 0x7f676ad0 50.698: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=8) 50.699: |7f677000| UHCI init on dev 00:1d.3 (io=5060) 50.698: /7f66f000\ Start thread 50.698: /7f66e000\ Start thread 50.698: \7f66e000/ End thread 50.698: /7f66e000\ Start thread 50.698: \7f66e000/ End thread 50.699: \7f673000/ End thread 50.698: |7f671000| device rev=0200 cls=09 sub=00 proto=02 size=64 50.698: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=9) 50.698: \7f677000/ End thread 50.698: /7f673000\ Start thread 50.698: \7f673000/ End thread 50.699: \7f672000/ End thread 50.698: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=41) 50.699: \7f670000/ End thread 50.699: |7f671000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 50.699: \7f66f000/ End thread 50.698: |7f671000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=7) 50.698: /7f673000\ Start thread 50.699: |7f673000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 50.699: /7f672000\ Start thread 50.699: /7f670000\ Start thread 50.699: |7f670000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 50.699: /7f66f000\ Start thread 50.699: |7f672000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 50.699: |7f66f000| ehci_control 0x7f676ad0 (dir=0 cmd=8 data=0) 50.780: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.783: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.784: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: |7f673000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: \7f673000/ End thread 50.784: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: |7f670000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: \7f670000/ End thread 50.785: |7f672000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: \7f672000/ End thread 50.785: |7f66f000| ehci_control 0x7f676ad0 (dir=128 cmd=8 data=4) 50.785: \7f66f000/ End thread 50.785: |7f671000| Initialized USB HUB (0 ports used) 50.785: \7f671000/ End thread 50.788: \7f675000/ End thread 50.937: |7f674000| PS2 keyboard initialized 50.937: \7f674000/ End thread 50.937: All threads complete. 50.937: Scan for option roms 50.937: Attempting to init PCI bdf 00:00.0 (vd 8086:27a0) 50.938: Attempting to init PCI bdf 00:02.1 (vd 8086:27a6) 50.938: Attempting to init PCI bdf 00:1b.0 (vd 8086:27d8) 50.938: Attempting to init PCI bdf 00:1c.0 (vd 8086:27d0) 50.937: Attempting to init PCI bdf 00:1c.1 (vd 8086:27d2) 50.937: Attempting to init PCI bdf 00:1c.2 (vd 8086:27d4) 50.938: Attempting to init PCI bdf 00:1c.3 (vd 8086:27d6) 50.937: Attempting to init PCI bdf 00:1d.0 (vd 8086:27c8) 50.937: Attempting to init PCI bdf 00:1d.1 (vd 8086:27c9) 50.937: Attempting to init PCI bdf 00:1d.2 (vd 8086:27ca) 50.937: Attempting to init PCI bdf 00:1d.3 (vd 8086:27cb) 50.938: Attempting to init PCI bdf 00:1d.7 (vd 8086:27cc) 50.937: Attempting to init PCI bdf 00:1e.0 (vd 8086:2448) 50.937: Attempting to init PCI bdf 00:1f.0 (vd 8086:27b9) 50.937: Attempting to init PCI bdf 00:1f.2 (vd 8086:27c5) 50.937: Attempting to init PCI bdf 00:1f.3 (vd 8086:27da) 50.937: Attempting to init PCI bdf 01:00.0 (vd 8086:109a) 50.938: Attempting to init PCI bdf 02:00.0 (vd 8086:4227) 50.937: Attempting to init PCI bdf 05:00.0 (vd 1180:0476) 50.937: Attempting to init PCI bdf 05:00.1 (vd 1180:0552) 50.938: Attempting to init PCI bdf 05:00.2 (vd 1180:0822) 50.938: 50.938: Press F12 for boot menu. 50.937: 50.937: Checking for bootsplash 53.465: Searching bootorder for: HALT 53.466: Mapping cd drive 0x000f1660 53.466: Mapping hd drive 0x000f1610 to 0 53.466: drive 0x000f1610: PCHS=16383/16/63 translation=lba LCHS=1024/255/63 s=500118192 53.466: finalize PMM 53.466: malloc finalize 53.466: Space available for UMB: cf000-ee800, f0000-f15e0 53.466: Returned 253952 bytes of ZoneHigh 53.466: e820 map has 6 items: 53.466: 0: 0000000000000000 - 000000000009fc00 = 1 RAM 53.466: 1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED 53.465: 2: 00000000000f0000 - 0000000000100000 = 2 RESERVED 53.466: 3: 0000000000100000 - 000000007f6c2000 = 1 RAM 53.466: 4: 000000007f6c2000 - 0000000080000000 = 2 RESERVED 53.466: 5: 00000000f0000000 - 00000000f4000000 = 2 RESERVED 53.467: Jump to int19 53.466: enter handle_19: 53.466: NULL 53.466: Booting from DVD/CD... 53.467: Device reports MEDIUM NOT PRESENT 53.468: scsi_is_ready returned -1 53.468: Boot failed: Could not read from CDROM (code 0003) 53.468: enter handle_18: 53.468: NULL 53.468: Booting from Hard Disk... 53.468: Booting from 0000:7c00