SeaBIOS September 2024

seabios@seabios.org

3 participants
3 discussions

Extending SeaBIOS for additional USB-HID devices
by Fox, Ethan 26 Sep '24

26 Sep '24

Hello! I am a university student and I am interested in extending SeaBIOS for a project which involves requiring connecting a USB SoloKey to your computer during the boot process. Implementing this in SeaBIOS seems promising since it looks like SeaBIOS has code written to interface with USB-HID keyboard and mice. I believe that SoloKey also follows this USB-HID spec. Is it feasible to extend the USB-HID code to also interact with SoloKey, or am I going to run into some road blocks? Any advice is welcome. Thanks, Ethan Fox

1 0

[PATCH 0/2] pci: skip pci resource allocation if instructed by platform
by Abhimanyu Saini 18 Sep '24

18 Sep '24

A hypervisor may want to perform PCI resource allocation (bus numbers, io and mmio ranges) and program the resulting values into the devices itself rather than delegate this to the firmware. Introduce a new flag in fw_cfg, "etc/pci-noalloc", to instruct the firmware to skip the resource allocation phase and use whatever is already programmed in the devices. Abhimanyu Saini (2): fw/pciinit: factor out pci resource allocation pci: skip pci resource allocation if instructed by platform src/fw/pciinit.c | 40 ++++++++++++++++++++++++++-------------- 1 file changed, 26 insertions(+), 14 deletions(-) -- 2.40.1 Amazon Web Services Development Center Germany GmbH Krausenstr. 38 10117 Berlin Geschaeftsfuehrung: Christian Schlaeger, Jonathan Weiss Eingetragen am Amtsgericht Charlottenburg unter HRB 257764 B Sitz: Berlin Ust-ID: DE 365 538 597

1 2

[PATCH] esp-scsi: indicate acceptance of MESSAGE IN phase data
by Mark Cave-Ayland 04 Sep '24

04 Sep '24

When the target has sent its MESSAGE IN phase data to the initiator, it waits for the initiator to release the ACK signal before disconnecting from the bus. Send a MSG_ACC command to the ESP so that the initiator releases the ACK signal to allow the target to disconnect, and also return the ASC back to the disconnected state. Signed-off-by: Mark Cave-Ayland <mark.cave-ayland(a)ilande.co.uk> --- src/hw/esp-scsi.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) [MCA: this is required for an upcoming QEMU ESP patch series which enforces the commands that can be executed in each internal ESP state. Without this fix SeaBIOS doesn't return the ESP back to its disconnected state after the SCSI transfer, causing subsequent ESP commands to fail.] diff --git a/src/hw/esp-scsi.c b/src/hw/esp-scsi.c index 8612069f..e1bee545 100644 --- a/src/hw/esp-scsi.c +++ b/src/hw/esp-scsi.c @@ -50,6 +50,7 @@ #define ESP_CMD_RESET 0x02 #define ESP_CMD_TI 0x10 #define ESP_CMD_ICCS 0x11 +#define ESP_CMD_MSGACC 0x12 #define ESP_CMD_SELATN 0x42 #define ESP_STAT_DI 0x01 @@ -159,11 +160,12 @@ esp_scsi_process_op(struct disk_op_s *op) continue; } - /* Finally read data from the message in phase. */ + /* Finally read data from the message in phase and accept. */ if (state == 3 && (stat & ESP_STAT_MSG)) { state++; status = inb(iobase + ESP_FIFO); inb(iobase + ESP_FIFO); + outb(ESP_CMD_MSGACC, iobase + ESP_CMD); break; } usleep(5); -- 2.39.2

2 1

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

SeaBIOS September 2024