SeaBIOS September 2015

seabios@seabios.org

14 participants
18 discussions

Start a nNew thread

"bootorder" documentation change
by Maxime de Roucy 08 Sep '15

08 Sep '15

Hello, I would like to submit the patch attached, regarding the bootorder documentation. -- Regards Maxime de Roucy

3 4

Unremovable USB3 device can not be detected after reboot
by Zheng Bao 06 Sep '15

06 Sep '15

Hi, All, My test environment. Main Board: AMD Bettong SeaBIOS: 1.8.0 USB3 device: USB MSC vendor='Seagate' product='FA GoFlex Pro' rev='0210' type=0 removable=0 The device can be detected at Seabios stage only when the board is power up first time. If I press the reset button, it can not be detected. I have to unplug, plug the power cable and power up again, the usb3 device can be detected. Removable USB flash disk doesnt have that problem. Zheng

3 10

Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached when power up (Summary: not final fixed yet)
by Zheng Bao 05 Sep '15

05 Sep '15

http://review.coreboot.org/#/c/11376/Only this can be apply to Trinity. Zheng > Date: Wed, 2 Sep 2015 17:22:30 +0200 > From: vidwer(a)gmail.com > To: seabios(a)seabios.org > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached when power up (Summary: not final fixed yet) > > 2015-08-26 14:33 GMT+02:00 Zheng Bao <fishbaoz(a)hotmail.com>: > > Yes. Need test by our validation dept. > > Hello Zheng, > > Is there an estimated turnaround time for changes to be delivered? > > Would the following changesets apply to Trinity? > http://review.coreboot.org/#/c/11375/ > http://review.coreboot.org/#/c/11376/ > http://review.coreboot.org/#/c/11377/ > > Idwer > > > > > > >> Date: Wed, 26 Aug 2015 13:55:52 +0200 > >> From: vidwer(a)gmail.com > >> To: seabios(a)seabios.org > >> Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> attached when power up (Summary: not final fixed yet) > > > >> > >> 2015-08-26 10:02 GMT+02:00 Zheng Bao <fishbaoz(a)hotmail.com>: > >> > Changing the AMD register in Coreboot code can only solve the USB3 > >> > problem > >> > in OS. In SeaBIOS stage, the problem still exists. > >> > >> Will you submit a change to AGESA? > >> > >> > > >> > I will start a new thread to describe the problem. > >> > > >> > Zheng > >> > > >> > ________________________________ > >> > From: fishbaoz(a)hotmail.com > >> > To: vidwer(a)gmail.com; seabios(a)seabios.org > >> > Date: Wed, 26 Aug 2015 05:35:12 +0000 > >> > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> > attached > >> > when power up > >> > > >> > Problem solved. It is about a internal register setting. > >> > Zheng > >> > > >> > > >> > ________________________________ > >> > From: fishbaoz(a)hotmail.com > >> > To: vidwer(a)gmail.com; seabios(a)seabios.org > >> > Date: Tue, 25 Aug 2015 12:06:34 +0000 > >> > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> > attached > >> > when power up > >> > > >> > Message after power up. xhci is ok. > >> > ---------------------------- > >> > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > >> > Found coreboot cbmem console @ bffde000 > >> > Found mainboard AMD Parmer > >> > Relocating init from 0x000e7b40 to 0xbff55050 (size 40688) > >> > Found CBFS header at 0xfffffc60 > >> > CPU Mhz=2497 > >> > Found 23 PCI devices (max PCI bus is 02) > >> > Copying SMBIOS entry point from 0xbffa7000 to 0x000f1a10 > >> > Copying ACPI RSDP from 0xbffb8000 to 0x000f19e0 > >> > Copying MPTABLE from 0xbffdc000/bffdc010 to 0x000f17b0 > >> > Copying PIR from 0xbffdd000 to 0x000f1780 > >> > Using pmtimer, ioport 0x818 > >> > Scan for VGA option rom > >> > Running option rom at c000:0003 > >> > Turning on vga text mode console > >> > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > >> > /bff52000\ Start thread > >> > |bff52000| XHCI init on dev 00:10.0: regs @ 0xf0248000, 4 ports, 32 > >> > slots, > >> > 32 byte contexts > >> > |bff52000| XHCI extcap 0x1 @ f0248500 > >> > |bff52000| XHCI protocol USB 3.00, 2 ports (offset 1), def 0 > >> > |bff52000| XHCI protocol USB 2.00, 2 ports (offset 3), def 0 > >> > /bff51000\ Start thread > >> > |bff51000| configure_xhci: resetting > >> > Found 1 serial ports > >> > AHCI controller at 11.0, iobase f024d000, irq 0 > >> > AHCI: cap 0xf3309f05, ports_impl 0x3f > >> > /bff50000\ Start thread > >> > |bff50000| AHCI/0: probing > >> > |bff52000| EHCI init on dev 00:12.2 (regs=0xf024d820) > >> > /bff4f000\ Start thread > >> > /bff4d000\ Start thread > >> > |bff4d000| AHCI/1: probing > >> > |bff50000| AHCI/0: link down > >> > |bff52000| EHCI init on dev 00:13.2 (regs=0xf024d920) > >> > /bff4c000\ Start thread > >> > /bff4b000\ Start thread > >> > |bff4b000| AHCI/2: probing > >> > |bff4d000| AHCI/1: link down > >> > \bff50000/ End thread > >> > |bff52000| OHCI init on dev 00:12.0 (regs=0xf024a000) > >> > /bff50000\ Start thread > >> > /bff4a000\ Start thread > >> > /bff49000\ Start thread > >> > |bff49000| AHCI/3: probing > >> > |bff4b000| AHCI/2: link down > >> > \bff4d000/ End thread > >> > |bff52000| OHCI init on dev 00:13.0 (regs=0xf024b000) > >> > /bff4d000\ Start thread > >> > /bff48000\ Start thread > >> > /bff47000\ Start thread > >> > /bff45000\ Start thread > >> > |bff45000| AHCI/4: probing > >> > |bff49000| AHCI/3: link down > >> > \bff4b000/ End thread > >> > |bff52000| OHCI init on dev 00:14.5 (regs=0xf024c000) > >> > /bff4b000\ Start thread > >> > /bff44000\ Start thread > >> > /bff43000\ Start thread > >> > /bff42000\ Start thread > >> > |bff42000| AHCI/5: probing > >> > |bff45000| AHCI/4: link down > >> > \bff49000/ End thread > >> > \bff52000/ End thread > >> > /bff52000\ Start thread > >> > \bff52000/ End thread > >> > /bff52000\ Start thread > >> > |bff42000| AHCI/5: link down > >> > \bff45000/ End thread > >> > /bff49000\ Start thread > >> > /bff46000\ Start thread > >> > /bff45000\ Start thread > >> > \bff42000/ End thread > >> > /bff42000\ Start thread > >> > /bff41000\ Start thread > >> > /bff40000\ Start thread > >> > /bff3f000\ Start thread > >> > /bff3e000\ Start thread > >> > /bff3d000\ Start thread > >> > /bff3c000\ Start thread > >> > /bff3b000\ Start thread > >> > |bff3b000| XHCI port #2: 0x00021203, powered, enabled, pls 0, speed 4 > >> > [Super] > >> > /bff3a000\ Start thread > >> > /bff39000\ Start thread > >> > /bff38000\ Start thread > >> > /bff37000\ Start thread > >> > /bff36000\ Start thread > >> > /bff35000\ Start thread > >> > |bff3b000| xhci_alloc_pipe: usbdev 0xbff53350, ring 0xbff9e400, slotid > >> > 0, > >> > epid 1 > >> > |bff3b000| xhci_cmd_enable_slot: > >> > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 1, len 0] > >> > |bff3b000| xhci_process_events: status change port #2 > >> > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed00, evt > >> > 0xbff9ee00, type 33, eidx 1, cc 1] > >> > |bff3b000| xhci_alloc_pipe: enable slot: got slotid 1 > >> > |bff3b000| xhci_cmd_address_device: slotid 1 > >> > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 2, len 0] > >> > /bff34000\ Start thread > >> > /bff33000\ Start thread > >> > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed10, evt > >> > 0xbff9ee00, type 33, eidx 2, cc 1] > >> > |bff3b000| xhci_realloc_pipe: usbdev 0xbff53350, ring 0xbff9e400, slotid > >> > 1, > >> > epid 1 > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 1, len 8] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 2, len 8] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 3, len 0] > >> > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > >> > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e420, evt > >> > 0xbff9e500, type 32, eidx 3, cc 1] > >> > |bff3b000| xhci_realloc_pipe: usbdev 0xbff53350, ring 0xbff9e400, slotid > >> > 1, > >> > epid 1 > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 4, len 8] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 5, len 9] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 6, len 0] > >> > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > >> > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e450, evt > >> > 0xbff9e500, type 32, eidx 6, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 7, len 8] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 8, len 44] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 9, len 0] > >> > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > >> > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e480, evt > >> > 0xbff9e500, type 32, eidx 9, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 10, len 8] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 11, len 0] > >> > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > >> > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e4a0, evt > >> > 0xbff9e500, type 32, eidx 11, cc 1] > >> > |bff3b000| xhci_alloc_pipe: usbdev 0xbff53350, ring 0x000eee00, slotid > >> > 0, > >> > epid 3 > >> > |bff3b000| xhci_cmd_configure_endpoint: slotid 1, add 0x9, del 0x0 > >> > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 3, len 0] > >> > |bff3a000| usb_hid_setup 0xbff4e920 > >> > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed20, evt > >> > 0xbff9ee00, type 33, eidx 3, cc 1] > >> > |bff3b000| xhci_alloc_pipe: usbdev 0xbff53350, ring 0x000eec00, slotid > >> > 0, > >> > epid 4 > >> > |bff3b000| xhci_cmd_configure_endpoint: slotid 1, add 0x11, del 0x0 > >> > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 4, len 0] > >> > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed30, evt > >> > 0xbff9ee00, type 33, eidx 4, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 12, len 8] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 13, len 1] > >> > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 14, len 0] > >> > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > >> > |bff3a000| USB keyboard initialized > >> > \bff3a000/ End thread > >> > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e4d0, evt > >> > 0xbff9e500, type 32, eidx 14, cc 1] > >> > |bff3b000| Searching bootorder for: > >> > /pci@i0cf8/usb@10/storage@2/*@0/*@0,0 > >> > |bff3b000| Searching bootorder for: /pci@i0cf8/usb@10/usb-*@2 > >> > |bff3b000| xhci_trb_queue: ring 0x000eec00 [nidx 1, len 31] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eec00, slotid 1, epid 4 > >> > |bff3b000| xhci_process_events: ring 0x000eec00 [trb 0x000eec00, evt > >> > 0x000eed00, type 32, eidx 1, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 1, len 36] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > >> > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee00, evt > >> > 0x000eef00, type 32, eidx 1, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 2, len 13] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > >> > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee10, evt > >> > 0x000eef00, type 32, eidx 2, cc 1] > >> > |bff3b000| USB MSC vendor='Seagate' product='FA GoFlex Pro' rev='0210' > >> > type=0 removable=0 > >> > |bff3b000| xhci_trb_queue: ring 0x000eec00 [nidx 2, len 31] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eec00, slotid 1, epid 4 > >> > |bff3b000| xhci_process_events: ring 0x000eec00 [trb 0x000eec10, evt > >> > 0x000eed00, type 32, eidx 2, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 3, len 13] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > >> > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee20, evt > >> > 0x000eef00, type 32, eidx 3, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0x000eec00 [nidx 3, len 31] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eec00, slotid 1, epid 4 > >> > |bff3b000| xhci_process_events: ring 0x000eec00 [trb 0x000eec20, evt > >> > 0x000eed00, type 32, eidx 3, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 4, len 8] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > >> > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee30, evt > >> > 0x000eef00, type 32, eidx 4, cc 1] > >> > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 5, len 13] > >> > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > >> > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee40, evt > >> > 0x000eef00, type 32, eidx 5, cc 1] > >> > |bff3b000| USB MSC blksize=512 sectors=976773167 > >> > \bff3b000/ End thread > >> > \bff45000/ End thread > >> > \bff52000/ End thread > >> > \bff43000/ End thread > >> > \bff47000/ End thread > >> > \bff4a000/ End thread > >> > \bff4f000/ End thread > >> > \bff41000/ End thread > >> > \bff46000/ End thread > >> > \bff44000/ End thread > >> > \bff48000/ End thread > >> > \bff4c000/ End thread > >> > \bff39000/ End thread > >> > \bff3c000/ End thread > >> > \bff3f000/ End thread > >> > \bff42000/ End thread > >> > \bff49000/ End thread > >> > \bff50000/ End thread > >> > \bff35000/ End thread > >> > \bff38000/ End thread > >> > \bff3e000/ End thread > >> > \bff33000/ End thread > >> > \bff36000/ End thread > >> > \bff3d000/ End thread > >> > \bff40000/ End thread > >> > \bff51000/ End thread > >> > \bff4d000/ End thread > >> > \bff34000/ End thread > >> > \bff37000/ End thread > >> > \bff4b000/ End thread > >> > All threads complete. > >> > Scan for option roms > >> > Searching bootorder for: /pci@i0cf8/*@1,1 > >> > > >> > Press F12 for boot menu. > >> > > >> > > >> > Messge after cold reset. xhci is not ok. > >> > ------------------------------------------------- > >> > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > >> > Found coreboot cbmem console @ bffde000 > >> > Found mainboard AMD Parmer > >> > Relocating init from 0x000e7b40 to 0xbff55050 (size 40688) > >> > Found CBFS header at 0xfffffc60 > >> > CPU Mhz=2498 > >> > Found 23 PCI devices (max PCI bus is 02) > >> > Copying SMBIOS entry point from 0xbffa7000 to 0x000f1a10 > >> > Copying ACPI RSDP from 0xbffb8000 to 0x000f19e0 > >> > Copying MPTABLE from 0xbffdc000/bffdc010 to 0x000f17b0 > >> > Copying PIR from 0xbffdd000 to 0x000f1780 > >> > Using pmtimer, ioport 0x818 > >> > Scan for VGA option rom > >> > Running option rom at c000:0003 > >> > Turning on vga text mode console > >> > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > >> > /bff52000\ Start thread > >> > |bff52000| XHCI init on dev 00:10.0: regs @ 0xf0248000, 4 ports, 32 > >> > slots, > >> > 32 byte contexts > >> > |bff52000| XHCI extcap 0x1 @ f0248500 > >> > |bff52000| XHCI protocol USB 3.00, 2 ports (offset 1), def 0 > >> > |bff52000| XHCI protocol USB 2.00, 2 ports (offset 3), def 0 > >> > /bff51000\ Start thread > >> > |bff51000| configure_xhci: resetting > >> > Found 1 serial ports > >> > AHCI controller at 11.0, iobase f024d000, irq 0 > >> > AHCI: cap 0xf3309f05, ports_impl 0x3f > >> > /bff50000\ Start thread > >> > |bff50000| AHCI/0: probing > >> > |bff52000| EHCI init on dev 00:12.2 (regs=0xf024d820) > >> > /bff4f000\ Start thread > >> > /bff4d000\ Start thread > >> > |bff4d000| AHCI/1: probing > >> > |bff50000| AHCI/0: link down > >> > |bff52000| EHCI init on dev 00:13.2 (regs=0xf024d920) > >> > /bff4c000\ Start thread > >> > /bff4b000\ Start thread > >> > |bff4b000| AHCI/2: probing > >> > |bff4d000| AHCI/1: link down > >> > \bff50000/ End thread > >> > |bff52000| OHCI init on dev 00:12.0 (regs=0xf024a000) > >> > /bff50000\ Start thread > >> > /bff4a000\ Start thread > >> > /bff49000\ Start thread > >> > /bff47000\ Start thread > >> > |bff47000| AHCI/3: probing > >> > |bff4b000| AHCI/2: link down > >> > \bff4d000/ End thread > >> > |bff52000| OHCI init on dev 00:13.0 (regs=0xf024b000) > >> > /bff4d000\ Start thread > >> > /bff46000\ Start thread > >> > /bff45000\ Start thread > >> > /bff44000\ Start thread > >> > /bff43000\ Start thread > >> > |bff43000| AHCI/4: probing > >> > |bff47000| AHCI/3: link down > >> > \bff4b000/ End thread > >> > |bff52000| OHCI init on dev 00:14.5 (regs=0xf024c000) > >> > /bff4b000\ Start thread > >> > /bff42000\ Start thread > >> > /bff41000\ Start thread > >> > /bff40000\ Start thread > >> > /bff3f000\ Start thread > >> > |bff3f000| AHCI/5: probing > >> > |bff43000| AHCI/4: link down > >> > \bff47000/ End thread > >> > \bff52000/ End thread > >> > /bff52000\ Start thread > >> > \bff52000/ End thread > >> > /bff52000\ Start thread > >> > /bff47000\ Start thread > >> > |bff47000| xhci_hub_reset port #4: 0x000202e1, powered, pls 7, speed 0 [ > >> > - ] > >> > |bff3f000| AHCI/5: link down > >> > \bff43000/ End thread > >> > /bff43000\ Start thread > >> > /bff3e000\ Start thread > >> > /bff3d000\ Start thread > >> > \bff3f000/ End thread > >> > /bff48000\ Start thread > >> > /bff3f000\ Start thread > >> > /bff3c000\ Start thread > >> > /bff3b000\ Start thread > >> > /bff3a000\ Start thread > >> > /bff39000\ Start thread > >> > /bff38000\ Start thread > >> > /bff37000\ Start thread > >> > /bff36000\ Start thread > >> > /bff35000\ Start thread > >> > /bff34000\ Start thread > >> > /bff33000\ Start thread > >> > |bff47000| XHCI port #4: 0x00200e03, powered, enabled, pls 0, speed 3 > >> > [High] > >> > |bff47000| xhci_alloc_pipe: usbdev 0xbff538a0, ring 0xbff9e400, slotid > >> > 0, > >> > epid 1 > >> > |bff47000| xhci_cmd_enable_slot: > >> > |bff47000| xhci_trb_queue: ring 0xbff9ed00 [nidx 1, len 0] > >> > |bff47000| xhci_process_events: status change port #4 > >> > |bff47000| xhci_process_events: status change port #2 > >> > |bff47000| xhci_process_events: status change port #4 > >> > |bff47000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed00, evt > >> > 0xbff9ee00, type 33, eidx 1, cc 1] > >> > |bff47000| xhci_alloc_pipe: enable slot: got slotid 1 > >> > |bff47000| xhci_cmd_address_device: slotid 1 > >> > |bff47000| xhci_trb_queue: ring 0xbff9ed00 [nidx 2, len 0] > >> > |bff38000| usb_hid_setup 0xbff4ec10 > >> > |bff38000| USB keyboard initialized > >> > \bff38000/ End thread > >> > \bff3d000/ End thread > >> > \bff52000/ End thread > >> > \bff41000/ End thread > >> > \bff45000/ End thread > >> > \bff4a000/ End thread > >> > \bff40000/ End thread > >> > \bff49000/ End thread > >> > \bff3c000/ End thread > >> > \bff3e000/ End thread > >> > \bff42000/ End thread > >> > \bff46000/ End thread > >> > \bff4f000/ End thread > >> > \bff4c000/ End thread > >> > \bff34000/ End thread > >> > \bff37000/ End thread > >> > \bff3a000/ End thread > >> > \bff3f000/ End thread > >> > \bff43000/ End thread > >> > \bff33000/ End thread > >> > \bff35000/ End thread > >> > \bff3b000/ End thread > >> > \bff48000/ End thread > >> > \bff36000/ End thread > >> > \bff39000/ End thread > >> > \bff50000/ End thread > >> > \bff4d000/ End thread > >> > \bff4b000/ End thread > >> > |bff47000| WARNING - Timeout at xhci_event_wait:692! > >> > |bff47000| xhci_alloc_pipe: address device: failed (cc -1) > >> > \bff47000/ End thread > >> > |bff44000| XHCI port #2: 0x00021203, powered, enabled, pls 0, speed 4 > >> > [Super] > >> > |bff44000| xhci_alloc_pipe: usbdev 0xbff53250, ring 0xbff9e900, slotid > >> > 0, > >> > epid 1 > >> > |bff44000| xhci_cmd_enable_slot: > >> > |bff44000| xhci_trb_queue: ring 0xbff9ed00 [nidx 3, len 0] > >> > |bff44000| WARNING - Timeout at xhci_event_wait:692! > >> > |bff44000| xhci_alloc_pipe: enable slot: failed > >> > \bff44000/ End thread > >> > |bff51000| XHCI no devices found > >> > |bff51000| WARNING - Timeout at wait_bit:310! > >> > \bff51000/ End thread > >> > All threads complete. > >> > Scan for option roms > >> > Searching bootorder for: /pci@i0cf8/*@1,1 > >> > --------------------------- > >> > > >> > ________________________________ > >> > From: fishbaoz(a)hotmail.com > >> > To: vidwer(a)gmail.com; seabios(a)seabios.org > >> > Date: Tue, 25 Aug 2015 08:33:00 +0000 > >> > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> > attached > >> > when power up > >> > > >> > > >> > New finding. > >> > > >> > If I cold power up the board, the Hispeed USB harddrive works. > >> > If I press the reset buttong, it doesn't work. > >> > I need to unplug and plug the power cable to make it work again. > >> > > >> > Do you have any idea about that? > >> > > >> > Zheng > >> > > >> > > >> > ________________________________ > >> > From: fishbaoz(a)hotmail.com > >> > To: vidwer(a)gmail.com; seabios(a)seabios.org > >> > Date: Tue, 25 Aug 2015 06:11:53 +0000 > >> > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> > attached > >> > when power up > >> > > >> > I tried with Parmer, which I assume is close to ASUS F2A85-M, and got > >> > the > >> > same result. > >> > :( > >> > > >> > ----------------------------------- > >> > hudson_enable() > >> > PCI: 00:10.0 [1022/7812] enabled > >> > hudson_enable() > >> > ---------------------------------------------- > >> > > >> > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_015821-supersrv) > >> > Found coreboot cbmem console @ bffde000 > >> > Found mainboard AMD Parmer > >> > Relocating init from 0x000e7b40 to 0xbff55050 (size 40688) > >> > Found CBFS header at 0xfffffc60 > >> > CPU Mhz=2498 > >> > Found 23 PCI devices (max PCI bus is 02) > >> > Copying SMBIOS entry point from 0xbffa7000 to 0x000f1a10 > >> > Copying ACPI RSDP from 0xbffb8000 to 0x000f19e0 > >> > Copying MPTABLE from 0xbffdc000/bffdc010 to 0x000f17b0 > >> > Copying PIR from 0xbffdd000 to 0x000f1780 > >> > Using pmtimer, ioport 0x818 > >> > Scan for VGA option rom > >> > Running option rom at c000:0003 > >> > Turning on vga text mode console > >> > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_015821-supersrv) > >> > /bff52000\ Start thread > >> > |bff52000| XHCI init on dev 00:10.0: regs @ 0xf0248000, 4 ports, 32 > >> > slots, > >> > 32 byte contexts > >> > |bff52000| XHCI extcap 0x1 @ f0248500 > >> > |bff52000| XHCI protocol USB 3.00, 2 ports (offset 1), def 0 > >> > |bff52000| XHCI protocol USB 2.00, 2 ports (offset 3), def 0 > >> > /bff51000\ Start thread > >> > |bff51000| configure_xhci: resetting > >> > Found 1 serial ports > >> > AHCI controller at 11.0, iobase f024d000, irq 0 > >> > AHCI: cap 0xf3309f05, ports_impl 0x3f > >> > /bff50000\ Start thread > >> > |bff50000| AHCI/0: probing > >> > |bff50000| AHCI/0: link up > >> > |bff52000| EHCI init on dev 00:12.2 (regs=0xf024d820) > >> > /bff4f000\ Start thread > >> > /bff4d000\ Start thread > >> > |bff4d000| AHCI/1: probing > >> > |bff50000| AHCI/0: ... finished, status 0x51, ERROR 0x4 > >> > |bff52000| EHCI init on dev 00:13.2 (regs=0xf024d920) > >> > /bff4c000\ Start thread > >> > /bff4b000\ Start thread > >> > |bff4b000| AHCI/2: probing > >> > |bff4d000| AHCI/1: link down > >> > |bff52000| OHCI init on dev 00:12.0 (regs=0xf024a000) > >> > /bff4a000\ Start thread > >> > /bff49000\ Start thread > >> > /bff48000\ Start thread > >> > /bff46000\ Start thread > >> > |bff46000| AHCI/3: probing > >> > |bff4b000| AHCI/2: link down > >> > \bff4d000/ End thread > >> > |bff50000| Searching bootorder for: /pci@i0cf8/*@11/drive@0/disk@0 > >> > |bff52000| OHCI init on dev 00:13.0 (regs=0xf024b000) > >> > /bff4d000\ Start thread > >> > /bff45000\ Start thread > >> > /bff44000\ Start thread > >> > /bff43000\ Start thread > >> > /bff42000\ Start thread > >> > |bff42000| AHCI/4: probing > >> > |bff46000| AHCI/3: link down > >> > \bff4b000/ End thread > >> > |bff50000| AHCI/0: registering: "AHCI/0: ST3250620NS ATA-7 Hard-Disk > >> > (232 > >> > GiBytes)" > >> > \bff50000/ End thread > >> > |bff52000| OHCI init on dev 00:14.5 (regs=0xf024c000) > >> > /bff50000\ Start thread > >> > /bff4b000\ Start thread > >> > /bff41000\ Start thread > >> > /bff40000\ Start thread > >> > /bff3f000\ Start thread > >> > |bff3f000| AHCI/5: probing > >> > |bff42000| AHCI/4: link down > >> > \bff46000/ End thread > >> > \bff52000/ End thread > >> > /bff46000\ Start thread > >> > /bff3e000\ Start thread > >> > \bff3e000/ End thread > >> > /bff3e000\ Start thread > >> > /bff3d000\ Start thread > >> > |bff3d000| xhci_hub_reset port #4: 0x000202e1, powered, pls 7, speed 0 [ > >> > - ] > >> > |bff3f000| AHCI/5: link down > >> > \bff42000/ End thread > >> > /bff47000\ Start thread > >> > /bff42000\ Start thread > >> > /bff3c000\ Start thread > >> > /bff3b000\ Start thread > >> > \bff3f000/ End thread > >> > /bff3f000\ Start thread > >> > /bff3a000\ Start thread > >> > /bff39000\ Start thread > >> > /bff38000\ Start thread > >> > /bff37000\ Start thread > >> > /bff36000\ Start thread > >> > /bff35000\ Start thread > >> > /bff34000\ Start thread > >> > /bff33000\ Start thread > >> > /bff32000\ Start thread > >> > |bff3d000| XHCI port #4: 0x00200e03, powered, enabled, pls 0, speed 3 > >> > [High] > >> > |bff3d000| xhci_alloc_pipe: usbdev 0xbff52f20, ring 0xbff9be00, slotid > >> > 0, > >> > epid 1 > >> > |bff3d000| xhci_cmd_enable_slot: > >> > |bff3d000| xhci_trb_queue: ring 0xbff9ed00 [nidx 1, len 0] > >> > |bff3d000| xhci_process_events: status change port #4 > >> > |bff3d000| xhci_process_events: status change port #2 > >> > |bff3d000| xhci_process_events: status change port #4 > >> > |bff3d000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed00, evt > >> > 0xbff9ee00, type 33, eidx 1, cc 1] > >> > |bff3d000| xhci_alloc_pipe: enable slot: got slotid 1 > >> > |bff3d000| xhci_cmd_address_device: slotid 1 > >> > |bff3d000| xhci_trb_queue: ring 0xbff9ed00 [nidx 2, len 0] > >> > |bff37000| usb_hid_setup 0xbff52a40 > >> > |bff37000| USB keyboard initialized > >> > \bff37000/ End thread > >> > \bff3b000/ End thread > >> > \bff3e000/ End thread > >> > \bff41000/ End thread > >> > \bff44000/ End thread > >> > \bff49000/ End thread > >> > \bff40000/ End thread > >> > \bff48000/ End thread > >> > \bff4f000/ End thread > >> > \bff39000/ End thread > >> > \bff3c000/ End thread > >> > \bff4b000/ End thread > >> > \bff45000/ End thread > >> > \bff4c000/ End thread > >> > \bff33000/ End thread > >> > \bff36000/ End thread > >> > \bff3a000/ End thread > >> > \bff42000/ End thread > >> > \bff46000/ End thread > >> > \bff4a000/ End thread > >> > \bff32000/ End thread > >> > \bff34000/ End thread > >> > \bff3f000/ End thread > >> > \bff47000/ End thread > >> > \bff4d000/ End thread > >> > \bff35000/ End thread > >> > \bff38000/ End thread > >> > \bff50000/ End thread > >> > |bff3d000| WARNING - Timeout at xhci_event_wait:692! > >> > |bff3d000| xhci_alloc_pipe: address device: failed (cc -1) > >> > \bff3d000/ End thread > >> > |bff43000| XHCI port #2: 0x00021203, powered, enabled, pls 0, speed 4 > >> > [Super] > >> > |bff43000| xhci_alloc_pipe: usbdev 0xbff4efe0, ring 0xbff9e900, slotid > >> > 0, > >> > epid 1 > >> > |bff43000| xhci_cmd_enable_slot: > >> > |bff43000| xhci_trb_queue: ring 0xbff9ed00 [nidx 3, len 0] > >> > |bff43000| WARNING - Timeout at xhci_event_wait:692! > >> > |bff43000| xhci_alloc_pipe: enable slot: failed > >> > \bff43000/ End thread > >> > |bff51000| XHCI no devices found > >> > |bff51000| WARNING - Timeout at wait_bit:310! > >> > \bff51000/ End thread > >> > All threads complete. > >> > Scan for option roms > >> > Searching bootorder for: /pci@i0cf8/*@1,1 > >> > > >> > Press F12 for boot menu. > >> > > >> > Select boot device: > >> > > >> > 1. AHCI/0: ST3250620NS ATA-7 Hard-Disk (232 GiBytes) > >> > 2. Legacy option rom > >> > > >> > Zheng > >> > > >> > > >> >> Date: Mon, 24 Aug 2015 15:12:13 +0200 > >> >> From: vidwer(a)gmail.com > >> >> To: seabios(a)seabios.org > >> >> Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> >> attached when power up > >> >> > >> >> 2015-08-24 14:19 GMT+02:00 Zheng Bao <fishbaoz(a)hotmail.com>: > >> >> > Hi, > >> >> > Please review the debug message below. > >> >> > > >> >> > Seabios message if USB3 harddrive is plugged in USB3 port. > >> >> > -------------------------------------------- > >> >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> >> > >> >> FWIW, I'm using the version from github master, 1.8.0 > >> >> > >> >> > Found coreboot cbmem console @ affde000 > >> >> > Found mainboard AMD FP4 > >> >> > Relocating init from 0x000e6d99 to 0xaff54770 (size 42948) > >> >> > Found CBFS header at 0xfffffc60 > >> >> > CPU Mhz=2101 > >> >> > Found 26 PCI devices (max PCI bus is 01) > >> >> > Copying SMBIOS entry point from 0xaffa7000 to 0x000f1540 > >> >> > Copying ACPI RSDP from 0xaffb8000 to 0x000f1510 > >> >> > Copying MPTABLE from 0xaffdc000/affdc010 to 0x000f1340 > >> >> > Copying PIR from 0xaffdd000 to 0x000f1310 > >> >> > Using pmtimer, ioport 0x818 > >> >> > Scan for VGA option rom > >> >> > Running option rom at c000:0003 > >> >> > Turning on vga text mode console > >> >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> >> > /aff51000\ Start thread > >> >> > |aff51000| XHCI init on dev 00:10.0: regs @ 0xf0b8a000, 8 ports, 32 > >> >> > slots, > >> >> > 32 byte contexts > >> >> > |aff51000| XHCI extcap 0x1 @ f0b8a500 > >> >> > |aff51000| XHCI protocol USB 3.00, 4 ports (offset 1), def 0 > >> >> > |aff51000| XHCI protocol USB 2.00, 4 ports (offset 5), def 18 > >> >> > |aff51000| XHCI extcap 0xa @ f0b8a540 > >> >> > /aff50000\ Start thread > >> >> > >> >> > /aff4f000\ Start thread > >> >> > |aff4f000| WARNING - Timeout at i8042_flush:71! > >> >> > \aff4f000/ End thread > >> >> > >> >> Where does that belong to? > >> >> > >> >> > |aff51000| EHCI init on dev 00:12.0 (regs=0xf0b8d520) > >> >> > /aff4f000\ Start thread > >> >> > /aff4d000\ Start thread > >> >> > Found 0 lpt ports > >> >> > Found 1 serial ports > >> >> > AHCI controller at 11.0, iobase f0b8d000, irq 0 > >> >> > AHCI: cap 0xf733ff01, ports_impl 0x3 > >> >> > /aff4c000\ Start thread > >> >> > |aff4c000| AHCI/0: probing > >> >> > |aff51000| EHCI init on dev 01:00.4 (regs=0xf0818020) > >> >> > /aff4b000\ Start thread > >> >> > /aff4a000\ Start thread > >> >> > /aff49000\ Start thread > >> >> > /aff47000\ Start thread > >> >> > |aff47000| AHCI/1: probing > >> >> > |aff47000| AHCI/1: link up > >> >> > |aff4c000| AHCI/0: link down > >> >> > |aff47000| AHCI/1: ... finished, status 0x51, ERROR 0x4 > >> >> > \aff4c000/ End thread > >> >> > |aff47000| Searching bootorder for: /pci@i0cf8/*@11/drive@1/disk@0 > >> >> > \aff4a000/ End thread > >> >> > \aff49000/ End thread > >> >> > |aff47000| AHCI/1: registering: "AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 > >> >> > Hard-Disk (119 GiBytes)" > >> >> > \aff47000/ End thread > >> >> > \aff51000/ End thread > >> >> > /aff4c000\ Start thread > >> >> > /aff4a000\ Start thread > >> >> > /aff49000\ Start thread > >> >> > /aff48000\ Start thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > /aff46000\ Start thread > >> >> > \aff46000/ End thread > >> >> > /aff46000\ Start thread > >> >> > \aff46000/ End thread > >> >> > /aff46000\ Start thread > >> >> > \aff46000/ End thread > >> >> > |aff4a000| usb_hid_setup 0xaff51c50 > >> >> > |aff4b000| WARNING - Timeout at ehci_waittick:186! > >> >> > >> >> I haven't seen this before. > >> >> > >> >> > |aff4a000| USB keyboard initialized > >> >> > \aff4a000/ End thread > >> >> > \aff4b000/ End thread > >> >> > |aff47000| WARNING - Timeout at wait_bit:484! > >> >> > \aff47000/ End thread > >> >> > |aff50000| XHCI no devices found > >> >> > \aff50000/ End thread > >> >> > \aff4c000/ End thread > >> >> > \aff48000/ End thread > >> >> > \aff49000/ End thread > >> >> > |aff4d000| Initialized USB HUB (1 ports used) > >> >> > \aff4d000/ End thread > >> >> > \aff4f000/ End thread > >> >> > All threads complete. > >> >> > Scan for option roms > >> >> > > >> >> > Press F12 for boot menu. > >> >> > > >> >> > Select boot device: > >> >> > > >> >> > 1. AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 Hard-Disk (119 GiBytes > >> >> > > >> >> > > >> >> > > >> >> > Seabios message if USB3 hard drive is plugged in USB2 port. > >> >> > ------------------------------ > >> >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> >> > Found coreboot cbmem console @ affde000 > >> >> > Found mainboard AMD FP4 > >> >> > Relocating init from 0x000e6d99 to 0xaff54770 (size 42948) > >> >> > Found CBFS header at 0xfffffc60 > >> >> > CPU Mhz=2100 > >> >> > Found 26 PCI devices (max PCI bus is 01) > >> >> > Copying SMBIOS entry point from 0xaffa7000 to 0x000f1540 > >> >> > Copying ACPI RSDP from 0xaffb8000 to 0x000f1510 > >> >> > Copying MPTABLE from 0xaffdc000/affdc010 to 0x000f1340 > >> >> > Copying PIR from 0xaffdd000 to 0x000f1310 > >> >> > Using pmtimer, ioport 0x818 > >> >> > Scan for VGA option rom > >> >> > Running option rom at c000:0003 > >> >> > Turning on vga text mode console > >> >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> >> > /aff51000\ Start thread > >> >> > |aff51000| XHCI init on dev 00:10.0: regs @ 0xf0b8a000, 8 ports, 32 > >> >> > slots, > >> >> > 32 byte contexts > >> >> > |aff51000| XHCI extcap 0x1 @ f0b8a500 > >> >> > |aff51000| XHCI protocol USB 3.00, 4 ports (offset 1), def 0 > >> >> > |aff51000| XHCI protocol USB 2.00, 4 ports (offset 5), def 18 > >> >> > |aff51000| XHCI extcap 0xa @ f0b8a540 > >> >> > /aff50000\ Start thread > >> >> > /aff4f000\ Start thread > >> >> > |aff4f000| WARNING - Timeout at i8042_flush:71! > >> >> > \aff4f000/ End thread > >> >> > |aff51000| EHCI init on dev 00:12.0 (regs=0xf0b8d520) > >> >> > /aff4f000\ Start thread > >> >> > /aff4d000\ Start thread > >> >> > Found 0 lpt ports > >> >> > Found 1 serial ports > >> >> > AHCI controller at 11.0, iobase f0b8d000, irq 0 > >> >> > AHCI: cap 0xf733ff01, ports_impl 0x3 > >> >> > /aff4c000\ Start thread > >> >> > |aff4c000| AHCI/0: probing > >> >> > |aff51000| EHCI init on dev 01:00.4 (regs=0xf0818020) > >> >> > /aff4b000\ Start thread > >> >> > /aff4a000\ Start thread > >> >> > /aff49000\ Start thread > >> >> > /aff47000\ Start thread > >> >> > |aff47000| AHCI/1: probing > >> >> > |aff47000| AHCI/1: link up > >> >> > |aff4c000| AHCI/0: link down > >> >> > |aff47000| AHCI/1: ... finished, status 0x51, ERROR 0x4 > >> >> > \aff4c000/ End thread > >> >> > |aff47000| Searching bootorder for: /pci@i0cf8/*@11/drive@1/disk@0 > >> >> > \aff4a000/ End thread > >> >> > \aff49000/ End thread > >> >> > |aff47000| AHCI/1: registering: "AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 > >> >> > Hard-Disk (119 GiBytes)" > >> >> > \aff47000/ End thread > >> >> > \aff51000/ End thread > >> >> > /aff4c000\ Start thread > >> >> > /aff4a000\ Start thread > >> >> > /aff49000\ Start thread > >> >> > /aff48000\ Start thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > /aff47000\ Start thread > >> >> > \aff47000/ End thread > >> >> > |aff50000| XHCI no devices found > >> >> > \aff50000/ End thread > >> >> > |aff4b000| WARNING - Timeout at ehci_waittick:186! > >> >> > \aff4b000/ End thread > >> >> > |aff4c000| Searching bootorder for: > >> >> > /pci@i0cf8/usb@12/hub@1/storage@1/*@0/*@0,0 > >> >> > |aff4c000| Searching bootorder for: /pci@i0cf8/usb@12/hub@1/usb-*@1 > >> >> > |aff4c000| USB MSC vendor='Seagate' product='FA GoFlex Pro' > >> >> > rev='0210' > >> >> > type=0 removable=0 > >> >> > |aff4c000| USB MSC blksize=512 sectors=976773167 > >> >> > \aff4c000/ End thread > >> >> > |aff4a000| usb_hid_setup 0xaff521d0 > >> >> > |aff4a000| USB keyboard initialized > >> >> > \aff4a000/ End thread > >> >> > \aff48000/ End thread > >> >> > \aff49000/ End thread > >> >> > |aff4d000| Initialized USB HUB (2 ports used) > >> >> > \aff4d000/ End thread > >> >> > \aff4f000/ End thread > >> >> > All threads complete. > >> >> > Scan for option roms > >> >> > > >> >> > Press F12 for boot menu. > >> >> > > >> >> > Select boot device: > >> >> > > >> >> > 1. AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 Hard-Disk (119 GiBytes > >> >> > 2. USB MSC Drive Seagate FA GoFlex Pro 0210 > >> >> > > >> >> > > >> >> >> Date: Thu, 20 Aug 2015 13:14:54 +0200 > >> >> >> From: vidwer(a)gmail.com > >> >> >> To: seabios(a)seabios.org > >> >> > > >> >> >> Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> >> >> attached when power up > >> >> >> > >> >> >> 2015-08-07 23:21 GMT+02:00 Kevin O'Connor <kevin(a)koconnor.net>: > >> >> >> > On Thu, Aug 06, 2015 at 11:51:04AM +0000, Zheng Bao wrote: > >> >> >> >> Board: Bettong > >> >> >> >> USB3 controller: Hudson on Carrizo > >> >> >> >> USB3 device: Seagate USB hard drive. That is the only USB 3.0 > >> >> >> >> device > >> >> >> >> I > >> >> >> >> can get. > >> >> >> > > >> >> >> > Thanks. The problem looks very similar to one reported in the past > >> >> >> > by > >> >> >> > Idwer. Unfortunately, Idwer also didn't have access to any other > >> >> >> > USB3 > >> >> >> > devices - that would have been a great test to see if the quirky > >> >> >> > behavior was due to the controller or due to the device. > >> >> >> > >> >> >> The board I have is an Hudson-D4? board, ASUS F2A85-M with the lspci > >> >> >> ID: > >> >> >> 00:10.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] > >> >> >> FCH > >> >> >> USB XHCI Controller [1022:7812] (rev 03) > >> >> >> 00:10.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] > >> >> >> FCH > >> >> >> USB XHCI Controller [1022:7812] (rev 03) > >> >> >> > >> >> >> Zheng, can you recompile SeaBIOS with CONFIG_THREADS=y and > >> >> >> CONFIG_DEBUG_LEVEL=2 and try booting off the superspeed device > >> >> >> you're > >> >> >> using? > >> >> >> The experience I had was that, with those settings, this superspeed > >> >> >> SATA dock showed up in the device menu (press ESCape). > >> >> >> > >> >> >> If that won't make the device show up - be sure to post that > >> >> >> cbmem/console output - change USB_TIME_SIGATT in src/hw/usb.h to at > >> >> >> least 1000. > >> >> >> > >> >> >> HTH, > >> >> >> > >> >> >> Idwer > >> >> >> > >> >> >> > > >> >> >> > Can you provide the output from "lspci", "lsusb", and "lsusb -t". > >> >> >> > > >> >> >> > -Kevin > >> >> >> > > >> >> >> >> > >> >> >> >> Joe > >> >> >> >> > >> >> >> >> > Date: Wed, 5 Aug 2015 06:25:13 -0400 > >> >> >> >> > From: kevin(a)koconnor.net > >> >> >> >> > To: fishbaoz(a)hotmail.com > >> >> >> >> > CC: seabios(a)seabios.org > >> >> >> >> > Subject: Re: [SeaBIOS]: USB 3.0 port failed if a USB 3.0 device > >> >> >> >> > is > >> >> >> >> > attached when power up > >> >> >> >> > > >> >> >> >> > On Wed, Aug 05, 2015 at 07:40:50AM +0000, Zheng Bao wrote: > >> >> >> >> > > hi, Kevin, > >> >> >> >> > > I am debugging the coreboot on AMD board. > >> >> >> >> > > > >> >> >> >> > > I found if a device is populated on USB 3.0 port during > >> >> >> >> > > system > >> >> >> >> > > power up, the USB3.0 function fail after OS boot up. > >> >> >> >> > > If a USB 2.0 device is plugged, the port is OK. > >> >> >> >> > > Can you take a look at this? > >> >> >> >> > > >> >> >> >> > What board is this, what USB3 controller is it, and what USB3 > >> >> >> >> > device > >> >> >> >> > did the problem occur with? Does the problem occur with > >> >> >> >> > multiple/all > >> >> >> >> > USB3 devices or just one? > >> >> >> >> > > >> >> >> >> > -Kevin > >> >> >> >> > >> >> >> > >> >> >> _______________________________________________ > >> >> >> SeaBIOS mailing list > >> >> >> SeaBIOS(a)seabios.org > >> >> >> http://www.seabios.org/mailman/listinfo/seabios > >> >> > >> >> _______________________________________________ > >> >> SeaBIOS mailing list > >> >> SeaBIOS(a)seabios.org > >> >> http://www.seabios.org/mailman/listinfo/seabios > >> > > >> > _______________________________________________ SeaBIOS mailing list > >> > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > >> > > >> > _______________________________________________ SeaBIOS mailing list > >> > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > >> > > >> > _______________________________________________ SeaBIOS mailing list > >> > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > >> > > >> > _______________________________________________ SeaBIOS mailing list > >> > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > >> > >> _______________________________________________ > >> SeaBIOS mailing list > >> SeaBIOS(a)seabios.org > >> http://www.seabios.org/mailman/listinfo/seabios > > _______________________________________________ > SeaBIOS mailing list > SeaBIOS(a)seabios.org > http://www.seabios.org/mailman/listinfo/seabios

1 0

[PATCH] megasas: Fix outw, outl argument order
by Stefan Weil 03 Sep '15

03 Sep '15

The value is the first argument and the port is the second, but the code was using the opposite order. Cc: Hannes Reinecke <hare(a)suse.de> Signed-off-by: Stefan Weil <sw(a)weilnetz.de> --- The outw statement looks strange, because there is also an outl statement with the same arguments. Maybe both statements should either use outw or outl. Regards Stefan src/hw/megasas.c | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-) diff --git a/src/hw/megasas.c b/src/hw/megasas.c index 5a07ab3..c009951 100644 --- a/src/hw/megasas.c +++ b/src/hw/megasas.c @@ -301,9 +301,9 @@ static int megasas_transition_to_ready(struct pci_device *pci, u32 ioaddr) pci->device == PCI_DEVICE_ID_LSI_SAS2008 || pci->device == PCI_DEVICE_ID_LSI_SAS2208 || pci->device == PCI_DEVICE_ID_LSI_SAS3108) { - outl(ioaddr + MFI_DB, mfi_flags); + outl(mfi_flags, ioaddr + MFI_DB); } else { - outl(ioaddr + MFI_IDB, mfi_flags); + outl(mfi_flags, ioaddr + MFI_IDB); } break; case MFI_STATE_OPERATIONAL: @@ -312,7 +312,7 @@ static int megasas_transition_to_ready(struct pci_device *pci, u32 ioaddr) pci->device == PCI_DEVICE_ID_LSI_SAS2008 || pci->device == PCI_DEVICE_ID_LSI_SAS2208 || pci->device == PCI_DEVICE_ID_LSI_SAS3108) { - outl(ioaddr + MFI_DB, mfi_flags); + outl(mfi_flags, ioaddr + MFI_DB); if (pci->device == PCI_DEVICE_ID_LSI_SAS2208 || pci->device == PCI_DEVICE_ID_LSI_SAS3108) { int j = 0; @@ -327,7 +327,7 @@ static int megasas_transition_to_ready(struct pci_device *pci, u32 ioaddr) } } } else { - outw(ioaddr + MFI_IDB, mfi_flags); + outw(mfi_flags, ioaddr + MFI_IDB); } break; case MFI_STATE_READY: -- 2.1.4

3 2

[PATCHv2 0/6] Improve sdcard boot menu description
by Kevin O'Connor 03 Sep '15

03 Sep '15

This is a respin of a previous series to extend the sdcard boot menu description. Instead of showing the product name and card version, this series shows the product name and card capacity. The card capacity is more likely to mean something to an end-user than a manufacturer's card version. Kevin O'Connor (6): sdcard: Move sdcard_set_frequency()/sdcard_set_power() in sdcard.c sdcard: Move frequency setting into sdcard_card_setup() sdcard: Move drive registration to sdcard_card_setup() sdcard: Turn card_type into a bitmap and store if card is MMC type sdcard: Display sdcard product name in boot menu sdcard: Obtain card capacity and report it on the boot menu src/hw/sdcard.c | 219 ++++++++++++++++++++++++++++++++++---------------------- 1 file changed, 133 insertions(+), 86 deletions(-) -- 2.4.3

1 7

Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached when power up (Summary: not final fixed yet)
by Zheng Bao 02 Sep '15

02 Sep '15

Yes. Need test by our validation dept. > Date: Wed, 26 Aug 2015 13:55:52 +0200 > From: vidwer(a)gmail.com > To: seabios(a)seabios.org > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached when power up (Summary: not final fixed yet) > > 2015-08-26 10:02 GMT+02:00 Zheng Bao <fishbaoz(a)hotmail.com>: > > Changing the AMD register in Coreboot code can only solve the USB3 problem > > in OS. In SeaBIOS stage, the problem still exists. > > Will you submit a change to AGESA? > > > > > I will start a new thread to describe the problem. > > > > Zheng > > > > ________________________________ > > From: fishbaoz(a)hotmail.com > > To: vidwer(a)gmail.com; seabios(a)seabios.org > > Date: Wed, 26 Aug 2015 05:35:12 +0000 > > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached > > when power up > > > > Problem solved. It is about a internal register setting. > > Zheng > > > > > > ________________________________ > > From: fishbaoz(a)hotmail.com > > To: vidwer(a)gmail.com; seabios(a)seabios.org > > Date: Tue, 25 Aug 2015 12:06:34 +0000 > > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached > > when power up > > > > Message after power up. xhci is ok. > > ---------------------------- > > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > > Found coreboot cbmem console @ bffde000 > > Found mainboard AMD Parmer > > Relocating init from 0x000e7b40 to 0xbff55050 (size 40688) > > Found CBFS header at 0xfffffc60 > > CPU Mhz=2497 > > Found 23 PCI devices (max PCI bus is 02) > > Copying SMBIOS entry point from 0xbffa7000 to 0x000f1a10 > > Copying ACPI RSDP from 0xbffb8000 to 0x000f19e0 > > Copying MPTABLE from 0xbffdc000/bffdc010 to 0x000f17b0 > > Copying PIR from 0xbffdd000 to 0x000f1780 > > Using pmtimer, ioport 0x818 > > Scan for VGA option rom > > Running option rom at c000:0003 > > Turning on vga text mode console > > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > > /bff52000\ Start thread > > |bff52000| XHCI init on dev 00:10.0: regs @ 0xf0248000, 4 ports, 32 slots, > > 32 byte contexts > > |bff52000| XHCI extcap 0x1 @ f0248500 > > |bff52000| XHCI protocol USB 3.00, 2 ports (offset 1), def 0 > > |bff52000| XHCI protocol USB 2.00, 2 ports (offset 3), def 0 > > /bff51000\ Start thread > > |bff51000| configure_xhci: resetting > > Found 1 serial ports > > AHCI controller at 11.0, iobase f024d000, irq 0 > > AHCI: cap 0xf3309f05, ports_impl 0x3f > > /bff50000\ Start thread > > |bff50000| AHCI/0: probing > > |bff52000| EHCI init on dev 00:12.2 (regs=0xf024d820) > > /bff4f000\ Start thread > > /bff4d000\ Start thread > > |bff4d000| AHCI/1: probing > > |bff50000| AHCI/0: link down > > |bff52000| EHCI init on dev 00:13.2 (regs=0xf024d920) > > /bff4c000\ Start thread > > /bff4b000\ Start thread > > |bff4b000| AHCI/2: probing > > |bff4d000| AHCI/1: link down > > \bff50000/ End thread > > |bff52000| OHCI init on dev 00:12.0 (regs=0xf024a000) > > /bff50000\ Start thread > > /bff4a000\ Start thread > > /bff49000\ Start thread > > |bff49000| AHCI/3: probing > > |bff4b000| AHCI/2: link down > > \bff4d000/ End thread > > |bff52000| OHCI init on dev 00:13.0 (regs=0xf024b000) > > /bff4d000\ Start thread > > /bff48000\ Start thread > > /bff47000\ Start thread > > /bff45000\ Start thread > > |bff45000| AHCI/4: probing > > |bff49000| AHCI/3: link down > > \bff4b000/ End thread > > |bff52000| OHCI init on dev 00:14.5 (regs=0xf024c000) > > /bff4b000\ Start thread > > /bff44000\ Start thread > > /bff43000\ Start thread > > /bff42000\ Start thread > > |bff42000| AHCI/5: probing > > |bff45000| AHCI/4: link down > > \bff49000/ End thread > > \bff52000/ End thread > > /bff52000\ Start thread > > \bff52000/ End thread > > /bff52000\ Start thread > > |bff42000| AHCI/5: link down > > \bff45000/ End thread > > /bff49000\ Start thread > > /bff46000\ Start thread > > /bff45000\ Start thread > > \bff42000/ End thread > > /bff42000\ Start thread > > /bff41000\ Start thread > > /bff40000\ Start thread > > /bff3f000\ Start thread > > /bff3e000\ Start thread > > /bff3d000\ Start thread > > /bff3c000\ Start thread > > /bff3b000\ Start thread > > |bff3b000| XHCI port #2: 0x00021203, powered, enabled, pls 0, speed 4 > > [Super] > > /bff3a000\ Start thread > > /bff39000\ Start thread > > /bff38000\ Start thread > > /bff37000\ Start thread > > /bff36000\ Start thread > > /bff35000\ Start thread > > |bff3b000| xhci_alloc_pipe: usbdev 0xbff53350, ring 0xbff9e400, slotid 0, > > epid 1 > > |bff3b000| xhci_cmd_enable_slot: > > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 1, len 0] > > |bff3b000| xhci_process_events: status change port #2 > > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed00, evt > > 0xbff9ee00, type 33, eidx 1, cc 1] > > |bff3b000| xhci_alloc_pipe: enable slot: got slotid 1 > > |bff3b000| xhci_cmd_address_device: slotid 1 > > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 2, len 0] > > /bff34000\ Start thread > > /bff33000\ Start thread > > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed10, evt > > 0xbff9ee00, type 33, eidx 2, cc 1] > > |bff3b000| xhci_realloc_pipe: usbdev 0xbff53350, ring 0xbff9e400, slotid 1, > > epid 1 > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 1, len 8] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 2, len 8] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 3, len 0] > > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e420, evt > > 0xbff9e500, type 32, eidx 3, cc 1] > > |bff3b000| xhci_realloc_pipe: usbdev 0xbff53350, ring 0xbff9e400, slotid 1, > > epid 1 > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 4, len 8] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 5, len 9] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 6, len 0] > > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e450, evt > > 0xbff9e500, type 32, eidx 6, cc 1] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 7, len 8] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 8, len 44] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 9, len 0] > > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e480, evt > > 0xbff9e500, type 32, eidx 9, cc 1] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 10, len 8] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 11, len 0] > > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e4a0, evt > > 0xbff9e500, type 32, eidx 11, cc 1] > > |bff3b000| xhci_alloc_pipe: usbdev 0xbff53350, ring 0x000eee00, slotid 0, > > epid 3 > > |bff3b000| xhci_cmd_configure_endpoint: slotid 1, add 0x9, del 0x0 > > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 3, len 0] > > |bff3a000| usb_hid_setup 0xbff4e920 > > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed20, evt > > 0xbff9ee00, type 33, eidx 3, cc 1] > > |bff3b000| xhci_alloc_pipe: usbdev 0xbff53350, ring 0x000eec00, slotid 0, > > epid 4 > > |bff3b000| xhci_cmd_configure_endpoint: slotid 1, add 0x11, del 0x0 > > |bff3b000| xhci_trb_queue: ring 0xbff9ed00 [nidx 4, len 0] > > |bff3b000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed30, evt > > 0xbff9ee00, type 33, eidx 4, cc 1] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 12, len 8] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 13, len 1] > > |bff3b000| xhci_trb_queue: ring 0xbff9e400 [nidx 14, len 0] > > |bff3b000| xhci_xfer_kick: ring 0xbff9e400, slotid 1, epid 1 > > |bff3a000| USB keyboard initialized > > \bff3a000/ End thread > > |bff3b000| xhci_process_events: ring 0xbff9e400 [trb 0xbff9e4d0, evt > > 0xbff9e500, type 32, eidx 14, cc 1] > > |bff3b000| Searching bootorder for: /pci@i0cf8/usb@10/storage@2/*@0/*@0,0 > > |bff3b000| Searching bootorder for: /pci@i0cf8/usb@10/usb-*@2 > > |bff3b000| xhci_trb_queue: ring 0x000eec00 [nidx 1, len 31] > > |bff3b000| xhci_xfer_kick: ring 0x000eec00, slotid 1, epid 4 > > |bff3b000| xhci_process_events: ring 0x000eec00 [trb 0x000eec00, evt > > 0x000eed00, type 32, eidx 1, cc 1] > > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 1, len 36] > > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee00, evt > > 0x000eef00, type 32, eidx 1, cc 1] > > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 2, len 13] > > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee10, evt > > 0x000eef00, type 32, eidx 2, cc 1] > > |bff3b000| USB MSC vendor='Seagate' product='FA GoFlex Pro' rev='0210' > > type=0 removable=0 > > |bff3b000| xhci_trb_queue: ring 0x000eec00 [nidx 2, len 31] > > |bff3b000| xhci_xfer_kick: ring 0x000eec00, slotid 1, epid 4 > > |bff3b000| xhci_process_events: ring 0x000eec00 [trb 0x000eec10, evt > > 0x000eed00, type 32, eidx 2, cc 1] > > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 3, len 13] > > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee20, evt > > 0x000eef00, type 32, eidx 3, cc 1] > > |bff3b000| xhci_trb_queue: ring 0x000eec00 [nidx 3, len 31] > > |bff3b000| xhci_xfer_kick: ring 0x000eec00, slotid 1, epid 4 > > |bff3b000| xhci_process_events: ring 0x000eec00 [trb 0x000eec20, evt > > 0x000eed00, type 32, eidx 3, cc 1] > > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 4, len 8] > > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee30, evt > > 0x000eef00, type 32, eidx 4, cc 1] > > |bff3b000| xhci_trb_queue: ring 0x000eee00 [nidx 5, len 13] > > |bff3b000| xhci_xfer_kick: ring 0x000eee00, slotid 1, epid 3 > > |bff3b000| xhci_process_events: ring 0x000eee00 [trb 0x000eee40, evt > > 0x000eef00, type 32, eidx 5, cc 1] > > |bff3b000| USB MSC blksize=512 sectors=976773167 > > \bff3b000/ End thread > > \bff45000/ End thread > > \bff52000/ End thread > > \bff43000/ End thread > > \bff47000/ End thread > > \bff4a000/ End thread > > \bff4f000/ End thread > > \bff41000/ End thread > > \bff46000/ End thread > > \bff44000/ End thread > > \bff48000/ End thread > > \bff4c000/ End thread > > \bff39000/ End thread > > \bff3c000/ End thread > > \bff3f000/ End thread > > \bff42000/ End thread > > \bff49000/ End thread > > \bff50000/ End thread > > \bff35000/ End thread > > \bff38000/ End thread > > \bff3e000/ End thread > > \bff33000/ End thread > > \bff36000/ End thread > > \bff3d000/ End thread > > \bff40000/ End thread > > \bff51000/ End thread > > \bff4d000/ End thread > > \bff34000/ End thread > > \bff37000/ End thread > > \bff4b000/ End thread > > All threads complete. > > Scan for option roms > > Searching bootorder for: /pci@i0cf8/*@1,1 > > > > Press F12 for boot menu. > > > > > > Messge after cold reset. xhci is not ok. > > ------------------------------------------------- > > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > > Found coreboot cbmem console @ bffde000 > > Found mainboard AMD Parmer > > Relocating init from 0x000e7b40 to 0xbff55050 (size 40688) > > Found CBFS header at 0xfffffc60 > > CPU Mhz=2498 > > Found 23 PCI devices (max PCI bus is 02) > > Copying SMBIOS entry point from 0xbffa7000 to 0x000f1a10 > > Copying ACPI RSDP from 0xbffb8000 to 0x000f19e0 > > Copying MPTABLE from 0xbffdc000/bffdc010 to 0x000f17b0 > > Copying PIR from 0xbffdd000 to 0x000f1780 > > Using pmtimer, ioport 0x818 > > Scan for VGA option rom > > Running option rom at c000:0003 > > Turning on vga text mode console > > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_074224-supersrv) > > /bff52000\ Start thread > > |bff52000| XHCI init on dev 00:10.0: regs @ 0xf0248000, 4 ports, 32 slots, > > 32 byte contexts > > |bff52000| XHCI extcap 0x1 @ f0248500 > > |bff52000| XHCI protocol USB 3.00, 2 ports (offset 1), def 0 > > |bff52000| XHCI protocol USB 2.00, 2 ports (offset 3), def 0 > > /bff51000\ Start thread > > |bff51000| configure_xhci: resetting > > Found 1 serial ports > > AHCI controller at 11.0, iobase f024d000, irq 0 > > AHCI: cap 0xf3309f05, ports_impl 0x3f > > /bff50000\ Start thread > > |bff50000| AHCI/0: probing > > |bff52000| EHCI init on dev 00:12.2 (regs=0xf024d820) > > /bff4f000\ Start thread > > /bff4d000\ Start thread > > |bff4d000| AHCI/1: probing > > |bff50000| AHCI/0: link down > > |bff52000| EHCI init on dev 00:13.2 (regs=0xf024d920) > > /bff4c000\ Start thread > > /bff4b000\ Start thread > > |bff4b000| AHCI/2: probing > > |bff4d000| AHCI/1: link down > > \bff50000/ End thread > > |bff52000| OHCI init on dev 00:12.0 (regs=0xf024a000) > > /bff50000\ Start thread > > /bff4a000\ Start thread > > /bff49000\ Start thread > > /bff47000\ Start thread > > |bff47000| AHCI/3: probing > > |bff4b000| AHCI/2: link down > > \bff4d000/ End thread > > |bff52000| OHCI init on dev 00:13.0 (regs=0xf024b000) > > /bff4d000\ Start thread > > /bff46000\ Start thread > > /bff45000\ Start thread > > /bff44000\ Start thread > > /bff43000\ Start thread > > |bff43000| AHCI/4: probing > > |bff47000| AHCI/3: link down > > \bff4b000/ End thread > > |bff52000| OHCI init on dev 00:14.5 (regs=0xf024c000) > > /bff4b000\ Start thread > > /bff42000\ Start thread > > /bff41000\ Start thread > > /bff40000\ Start thread > > /bff3f000\ Start thread > > |bff3f000| AHCI/5: probing > > |bff43000| AHCI/4: link down > > \bff47000/ End thread > > \bff52000/ End thread > > /bff52000\ Start thread > > \bff52000/ End thread > > /bff52000\ Start thread > > /bff47000\ Start thread > > |bff47000| xhci_hub_reset port #4: 0x000202e1, powered, pls 7, speed 0 [ - ] > > |bff3f000| AHCI/5: link down > > \bff43000/ End thread > > /bff43000\ Start thread > > /bff3e000\ Start thread > > /bff3d000\ Start thread > > \bff3f000/ End thread > > /bff48000\ Start thread > > /bff3f000\ Start thread > > /bff3c000\ Start thread > > /bff3b000\ Start thread > > /bff3a000\ Start thread > > /bff39000\ Start thread > > /bff38000\ Start thread > > /bff37000\ Start thread > > /bff36000\ Start thread > > /bff35000\ Start thread > > /bff34000\ Start thread > > /bff33000\ Start thread > > |bff47000| XHCI port #4: 0x00200e03, powered, enabled, pls 0, speed 3 [High] > > |bff47000| xhci_alloc_pipe: usbdev 0xbff538a0, ring 0xbff9e400, slotid 0, > > epid 1 > > |bff47000| xhci_cmd_enable_slot: > > |bff47000| xhci_trb_queue: ring 0xbff9ed00 [nidx 1, len 0] > > |bff47000| xhci_process_events: status change port #4 > > |bff47000| xhci_process_events: status change port #2 > > |bff47000| xhci_process_events: status change port #4 > > |bff47000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed00, evt > > 0xbff9ee00, type 33, eidx 1, cc 1] > > |bff47000| xhci_alloc_pipe: enable slot: got slotid 1 > > |bff47000| xhci_cmd_address_device: slotid 1 > > |bff47000| xhci_trb_queue: ring 0xbff9ed00 [nidx 2, len 0] > > |bff38000| usb_hid_setup 0xbff4ec10 > > |bff38000| USB keyboard initialized > > \bff38000/ End thread > > \bff3d000/ End thread > > \bff52000/ End thread > > \bff41000/ End thread > > \bff45000/ End thread > > \bff4a000/ End thread > > \bff40000/ End thread > > \bff49000/ End thread > > \bff3c000/ End thread > > \bff3e000/ End thread > > \bff42000/ End thread > > \bff46000/ End thread > > \bff4f000/ End thread > > \bff4c000/ End thread > > \bff34000/ End thread > > \bff37000/ End thread > > \bff3a000/ End thread > > \bff3f000/ End thread > > \bff43000/ End thread > > \bff33000/ End thread > > \bff35000/ End thread > > \bff3b000/ End thread > > \bff48000/ End thread > > \bff36000/ End thread > > \bff39000/ End thread > > \bff50000/ End thread > > \bff4d000/ End thread > > \bff4b000/ End thread > > |bff47000| WARNING - Timeout at xhci_event_wait:692! > > |bff47000| xhci_alloc_pipe: address device: failed (cc -1) > > \bff47000/ End thread > > |bff44000| XHCI port #2: 0x00021203, powered, enabled, pls 0, speed 4 > > [Super] > > |bff44000| xhci_alloc_pipe: usbdev 0xbff53250, ring 0xbff9e900, slotid 0, > > epid 1 > > |bff44000| xhci_cmd_enable_slot: > > |bff44000| xhci_trb_queue: ring 0xbff9ed00 [nidx 3, len 0] > > |bff44000| WARNING - Timeout at xhci_event_wait:692! > > |bff44000| xhci_alloc_pipe: enable slot: failed > > \bff44000/ End thread > > |bff51000| XHCI no devices found > > |bff51000| WARNING - Timeout at wait_bit:310! > > \bff51000/ End thread > > All threads complete. > > Scan for option roms > > Searching bootorder for: /pci@i0cf8/*@1,1 > > --------------------------- > > > > ________________________________ > > From: fishbaoz(a)hotmail.com > > To: vidwer(a)gmail.com; seabios(a)seabios.org > > Date: Tue, 25 Aug 2015 08:33:00 +0000 > > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached > > when power up > > > > > > New finding. > > > > If I cold power up the board, the Hispeed USB harddrive works. > > If I press the reset buttong, it doesn't work. > > I need to unplug and plug the power cable to make it work again. > > > > Do you have any idea about that? > > > > Zheng > > > > > > ________________________________ > > From: fishbaoz(a)hotmail.com > > To: vidwer(a)gmail.com; seabios(a)seabios.org > > Date: Tue, 25 Aug 2015 06:11:53 +0000 > > Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is attached > > when power up > > > > I tried with Parmer, which I assume is close to ASUS F2A85-M, and got the > > same result. > > :( > > > > ----------------------------------- > > hudson_enable() > > PCI: 00:10.0 [1022/7812] enabled > > hudson_enable() > > ---------------------------------------------- > > > > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_015821-supersrv) > > Found coreboot cbmem console @ bffde000 > > Found mainboard AMD Parmer > > Relocating init from 0x000e7b40 to 0xbff55050 (size 40688) > > Found CBFS header at 0xfffffc60 > > CPU Mhz=2498 > > Found 23 PCI devices (max PCI bus is 02) > > Copying SMBIOS entry point from 0xbffa7000 to 0x000f1a10 > > Copying ACPI RSDP from 0xbffb8000 to 0x000f19e0 > > Copying MPTABLE from 0xbffdc000/bffdc010 to 0x000f17b0 > > Copying PIR from 0xbffdd000 to 0x000f1780 > > Using pmtimer, ioport 0x818 > > Scan for VGA option rom > > Running option rom at c000:0003 > > Turning on vga text mode console > > SeaBIOS (version rel-1.8.0-0-g4c59f5d-dirty-20150825_015821-supersrv) > > /bff52000\ Start thread > > |bff52000| XHCI init on dev 00:10.0: regs @ 0xf0248000, 4 ports, 32 slots, > > 32 byte contexts > > |bff52000| XHCI extcap 0x1 @ f0248500 > > |bff52000| XHCI protocol USB 3.00, 2 ports (offset 1), def 0 > > |bff52000| XHCI protocol USB 2.00, 2 ports (offset 3), def 0 > > /bff51000\ Start thread > > |bff51000| configure_xhci: resetting > > Found 1 serial ports > > AHCI controller at 11.0, iobase f024d000, irq 0 > > AHCI: cap 0xf3309f05, ports_impl 0x3f > > /bff50000\ Start thread > > |bff50000| AHCI/0: probing > > |bff50000| AHCI/0: link up > > |bff52000| EHCI init on dev 00:12.2 (regs=0xf024d820) > > /bff4f000\ Start thread > > /bff4d000\ Start thread > > |bff4d000| AHCI/1: probing > > |bff50000| AHCI/0: ... finished, status 0x51, ERROR 0x4 > > |bff52000| EHCI init on dev 00:13.2 (regs=0xf024d920) > > /bff4c000\ Start thread > > /bff4b000\ Start thread > > |bff4b000| AHCI/2: probing > > |bff4d000| AHCI/1: link down > > |bff52000| OHCI init on dev 00:12.0 (regs=0xf024a000) > > /bff4a000\ Start thread > > /bff49000\ Start thread > > /bff48000\ Start thread > > /bff46000\ Start thread > > |bff46000| AHCI/3: probing > > |bff4b000| AHCI/2: link down > > \bff4d000/ End thread > > |bff50000| Searching bootorder for: /pci@i0cf8/*@11/drive@0/disk@0 > > |bff52000| OHCI init on dev 00:13.0 (regs=0xf024b000) > > /bff4d000\ Start thread > > /bff45000\ Start thread > > /bff44000\ Start thread > > /bff43000\ Start thread > > /bff42000\ Start thread > > |bff42000| AHCI/4: probing > > |bff46000| AHCI/3: link down > > \bff4b000/ End thread > > |bff50000| AHCI/0: registering: "AHCI/0: ST3250620NS ATA-7 Hard-Disk (232 > > GiBytes)" > > \bff50000/ End thread > > |bff52000| OHCI init on dev 00:14.5 (regs=0xf024c000) > > /bff50000\ Start thread > > /bff4b000\ Start thread > > /bff41000\ Start thread > > /bff40000\ Start thread > > /bff3f000\ Start thread > > |bff3f000| AHCI/5: probing > > |bff42000| AHCI/4: link down > > \bff46000/ End thread > > \bff52000/ End thread > > /bff46000\ Start thread > > /bff3e000\ Start thread > > \bff3e000/ End thread > > /bff3e000\ Start thread > > /bff3d000\ Start thread > > |bff3d000| xhci_hub_reset port #4: 0x000202e1, powered, pls 7, speed 0 [ - ] > > |bff3f000| AHCI/5: link down > > \bff42000/ End thread > > /bff47000\ Start thread > > /bff42000\ Start thread > > /bff3c000\ Start thread > > /bff3b000\ Start thread > > \bff3f000/ End thread > > /bff3f000\ Start thread > > /bff3a000\ Start thread > > /bff39000\ Start thread > > /bff38000\ Start thread > > /bff37000\ Start thread > > /bff36000\ Start thread > > /bff35000\ Start thread > > /bff34000\ Start thread > > /bff33000\ Start thread > > /bff32000\ Start thread > > |bff3d000| XHCI port #4: 0x00200e03, powered, enabled, pls 0, speed 3 [High] > > |bff3d000| xhci_alloc_pipe: usbdev 0xbff52f20, ring 0xbff9be00, slotid 0, > > epid 1 > > |bff3d000| xhci_cmd_enable_slot: > > |bff3d000| xhci_trb_queue: ring 0xbff9ed00 [nidx 1, len 0] > > |bff3d000| xhci_process_events: status change port #4 > > |bff3d000| xhci_process_events: status change port #2 > > |bff3d000| xhci_process_events: status change port #4 > > |bff3d000| xhci_process_events: ring 0xbff9ed00 [trb 0xbff9ed00, evt > > 0xbff9ee00, type 33, eidx 1, cc 1] > > |bff3d000| xhci_alloc_pipe: enable slot: got slotid 1 > > |bff3d000| xhci_cmd_address_device: slotid 1 > > |bff3d000| xhci_trb_queue: ring 0xbff9ed00 [nidx 2, len 0] > > |bff37000| usb_hid_setup 0xbff52a40 > > |bff37000| USB keyboard initialized > > \bff37000/ End thread > > \bff3b000/ End thread > > \bff3e000/ End thread > > \bff41000/ End thread > > \bff44000/ End thread > > \bff49000/ End thread > > \bff40000/ End thread > > \bff48000/ End thread > > \bff4f000/ End thread > > \bff39000/ End thread > > \bff3c000/ End thread > > \bff4b000/ End thread > > \bff45000/ End thread > > \bff4c000/ End thread > > \bff33000/ End thread > > \bff36000/ End thread > > \bff3a000/ End thread > > \bff42000/ End thread > > \bff46000/ End thread > > \bff4a000/ End thread > > \bff32000/ End thread > > \bff34000/ End thread > > \bff3f000/ End thread > > \bff47000/ End thread > > \bff4d000/ End thread > > \bff35000/ End thread > > \bff38000/ End thread > > \bff50000/ End thread > > |bff3d000| WARNING - Timeout at xhci_event_wait:692! > > |bff3d000| xhci_alloc_pipe: address device: failed (cc -1) > > \bff3d000/ End thread > > |bff43000| XHCI port #2: 0x00021203, powered, enabled, pls 0, speed 4 > > [Super] > > |bff43000| xhci_alloc_pipe: usbdev 0xbff4efe0, ring 0xbff9e900, slotid 0, > > epid 1 > > |bff43000| xhci_cmd_enable_slot: > > |bff43000| xhci_trb_queue: ring 0xbff9ed00 [nidx 3, len 0] > > |bff43000| WARNING - Timeout at xhci_event_wait:692! > > |bff43000| xhci_alloc_pipe: enable slot: failed > > \bff43000/ End thread > > |bff51000| XHCI no devices found > > |bff51000| WARNING - Timeout at wait_bit:310! > > \bff51000/ End thread > > All threads complete. > > Scan for option roms > > Searching bootorder for: /pci@i0cf8/*@1,1 > > > > Press F12 for boot menu. > > > > Select boot device: > > > > 1. AHCI/0: ST3250620NS ATA-7 Hard-Disk (232 GiBytes) > > 2. Legacy option rom > > > > Zheng > > > > > >> Date: Mon, 24 Aug 2015 15:12:13 +0200 > >> From: vidwer(a)gmail.com > >> To: seabios(a)seabios.org > >> Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> attached when power up > >> > >> 2015-08-24 14:19 GMT+02:00 Zheng Bao <fishbaoz(a)hotmail.com>: > >> > Hi, > >> > Please review the debug message below. > >> > > >> > Seabios message if USB3 harddrive is plugged in USB3 port. > >> > -------------------------------------------- > >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> > >> FWIW, I'm using the version from github master, 1.8.0 > >> > >> > Found coreboot cbmem console @ affde000 > >> > Found mainboard AMD FP4 > >> > Relocating init from 0x000e6d99 to 0xaff54770 (size 42948) > >> > Found CBFS header at 0xfffffc60 > >> > CPU Mhz=2101 > >> > Found 26 PCI devices (max PCI bus is 01) > >> > Copying SMBIOS entry point from 0xaffa7000 to 0x000f1540 > >> > Copying ACPI RSDP from 0xaffb8000 to 0x000f1510 > >> > Copying MPTABLE from 0xaffdc000/affdc010 to 0x000f1340 > >> > Copying PIR from 0xaffdd000 to 0x000f1310 > >> > Using pmtimer, ioport 0x818 > >> > Scan for VGA option rom > >> > Running option rom at c000:0003 > >> > Turning on vga text mode console > >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> > /aff51000\ Start thread > >> > |aff51000| XHCI init on dev 00:10.0: regs @ 0xf0b8a000, 8 ports, 32 > >> > slots, > >> > 32 byte contexts > >> > |aff51000| XHCI extcap 0x1 @ f0b8a500 > >> > |aff51000| XHCI protocol USB 3.00, 4 ports (offset 1), def 0 > >> > |aff51000| XHCI protocol USB 2.00, 4 ports (offset 5), def 18 > >> > |aff51000| XHCI extcap 0xa @ f0b8a540 > >> > /aff50000\ Start thread > >> > >> > /aff4f000\ Start thread > >> > |aff4f000| WARNING - Timeout at i8042_flush:71! > >> > \aff4f000/ End thread > >> > >> Where does that belong to? > >> > >> > |aff51000| EHCI init on dev 00:12.0 (regs=0xf0b8d520) > >> > /aff4f000\ Start thread > >> > /aff4d000\ Start thread > >> > Found 0 lpt ports > >> > Found 1 serial ports > >> > AHCI controller at 11.0, iobase f0b8d000, irq 0 > >> > AHCI: cap 0xf733ff01, ports_impl 0x3 > >> > /aff4c000\ Start thread > >> > |aff4c000| AHCI/0: probing > >> > |aff51000| EHCI init on dev 01:00.4 (regs=0xf0818020) > >> > /aff4b000\ Start thread > >> > /aff4a000\ Start thread > >> > /aff49000\ Start thread > >> > /aff47000\ Start thread > >> > |aff47000| AHCI/1: probing > >> > |aff47000| AHCI/1: link up > >> > |aff4c000| AHCI/0: link down > >> > |aff47000| AHCI/1: ... finished, status 0x51, ERROR 0x4 > >> > \aff4c000/ End thread > >> > |aff47000| Searching bootorder for: /pci@i0cf8/*@11/drive@1/disk@0 > >> > \aff4a000/ End thread > >> > \aff49000/ End thread > >> > |aff47000| AHCI/1: registering: "AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 > >> > Hard-Disk (119 GiBytes)" > >> > \aff47000/ End thread > >> > \aff51000/ End thread > >> > /aff4c000\ Start thread > >> > /aff4a000\ Start thread > >> > /aff49000\ Start thread > >> > /aff48000\ Start thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > /aff46000\ Start thread > >> > \aff46000/ End thread > >> > /aff46000\ Start thread > >> > \aff46000/ End thread > >> > /aff46000\ Start thread > >> > \aff46000/ End thread > >> > |aff4a000| usb_hid_setup 0xaff51c50 > >> > |aff4b000| WARNING - Timeout at ehci_waittick:186! > >> > >> I haven't seen this before. > >> > >> > |aff4a000| USB keyboard initialized > >> > \aff4a000/ End thread > >> > \aff4b000/ End thread > >> > |aff47000| WARNING - Timeout at wait_bit:484! > >> > \aff47000/ End thread > >> > |aff50000| XHCI no devices found > >> > \aff50000/ End thread > >> > \aff4c000/ End thread > >> > \aff48000/ End thread > >> > \aff49000/ End thread > >> > |aff4d000| Initialized USB HUB (1 ports used) > >> > \aff4d000/ End thread > >> > \aff4f000/ End thread > >> > All threads complete. > >> > Scan for option roms > >> > > >> > Press F12 for boot menu. > >> > > >> > Select boot device: > >> > > >> > 1. AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 Hard-Disk (119 GiBytes > >> > > >> > > >> > > >> > Seabios message if USB3 hard drive is plugged in USB2 port. > >> > ------------------------------ > >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> > Found coreboot cbmem console @ affde000 > >> > Found mainboard AMD FP4 > >> > Relocating init from 0x000e6d99 to 0xaff54770 (size 42948) > >> > Found CBFS header at 0xfffffc60 > >> > CPU Mhz=2100 > >> > Found 26 PCI devices (max PCI bus is 01) > >> > Copying SMBIOS entry point from 0xaffa7000 to 0x000f1540 > >> > Copying ACPI RSDP from 0xaffb8000 to 0x000f1510 > >> > Copying MPTABLE from 0xaffdc000/affdc010 to 0x000f1340 > >> > Copying PIR from 0xaffdd000 to 0x000f1310 > >> > Using pmtimer, ioport 0x818 > >> > Scan for VGA option rom > >> > Running option rom at c000:0003 > >> > Turning on vga text mode console > >> > SeaBIOS (version rel-1.7.5-0-ge51488c-dirty-20150824_081102-supersrv) > >> > /aff51000\ Start thread > >> > |aff51000| XHCI init on dev 00:10.0: regs @ 0xf0b8a000, 8 ports, 32 > >> > slots, > >> > 32 byte contexts > >> > |aff51000| XHCI extcap 0x1 @ f0b8a500 > >> > |aff51000| XHCI protocol USB 3.00, 4 ports (offset 1), def 0 > >> > |aff51000| XHCI protocol USB 2.00, 4 ports (offset 5), def 18 > >> > |aff51000| XHCI extcap 0xa @ f0b8a540 > >> > /aff50000\ Start thread > >> > /aff4f000\ Start thread > >> > |aff4f000| WARNING - Timeout at i8042_flush:71! > >> > \aff4f000/ End thread > >> > |aff51000| EHCI init on dev 00:12.0 (regs=0xf0b8d520) > >> > /aff4f000\ Start thread > >> > /aff4d000\ Start thread > >> > Found 0 lpt ports > >> > Found 1 serial ports > >> > AHCI controller at 11.0, iobase f0b8d000, irq 0 > >> > AHCI: cap 0xf733ff01, ports_impl 0x3 > >> > /aff4c000\ Start thread > >> > |aff4c000| AHCI/0: probing > >> > |aff51000| EHCI init on dev 01:00.4 (regs=0xf0818020) > >> > /aff4b000\ Start thread > >> > /aff4a000\ Start thread > >> > /aff49000\ Start thread > >> > /aff47000\ Start thread > >> > |aff47000| AHCI/1: probing > >> > |aff47000| AHCI/1: link up > >> > |aff4c000| AHCI/0: link down > >> > |aff47000| AHCI/1: ... finished, status 0x51, ERROR 0x4 > >> > \aff4c000/ End thread > >> > |aff47000| Searching bootorder for: /pci@i0cf8/*@11/drive@1/disk@0 > >> > \aff4a000/ End thread > >> > \aff49000/ End thread > >> > |aff47000| AHCI/1: registering: "AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 > >> > Hard-Disk (119 GiBytes)" > >> > \aff47000/ End thread > >> > \aff51000/ End thread > >> > /aff4c000\ Start thread > >> > /aff4a000\ Start thread > >> > /aff49000\ Start thread > >> > /aff48000\ Start thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > /aff47000\ Start thread > >> > \aff47000/ End thread > >> > |aff50000| XHCI no devices found > >> > \aff50000/ End thread > >> > |aff4b000| WARNING - Timeout at ehci_waittick:186! > >> > \aff4b000/ End thread > >> > |aff4c000| Searching bootorder for: > >> > /pci@i0cf8/usb@12/hub@1/storage@1/*@0/*@0,0 > >> > |aff4c000| Searching bootorder for: /pci@i0cf8/usb@12/hub@1/usb-*@1 > >> > |aff4c000| USB MSC vendor='Seagate' product='FA GoFlex Pro' rev='0210' > >> > type=0 removable=0 > >> > |aff4c000| USB MSC blksize=512 sectors=976773167 > >> > \aff4c000/ End thread > >> > |aff4a000| usb_hid_setup 0xaff521d0 > >> > |aff4a000| USB keyboard initialized > >> > \aff4a000/ End thread > >> > \aff48000/ End thread > >> > \aff49000/ End thread > >> > |aff4d000| Initialized USB HUB (2 ports used) > >> > \aff4d000/ End thread > >> > \aff4f000/ End thread > >> > All threads complete. > >> > Scan for option roms > >> > > >> > Press F12 for boot menu. > >> > > >> > Select boot device: > >> > > >> > 1. AHCI/1: PLEXTOR PX-128M6G-2280 ATA-8 Hard-Disk (119 GiBytes > >> > 2. USB MSC Drive Seagate FA GoFlex Pro 0210 > >> > > >> > > >> >> Date: Thu, 20 Aug 2015 13:14:54 +0200 > >> >> From: vidwer(a)gmail.com > >> >> To: seabios(a)seabios.org > >> > > >> >> Subject: Re: [SeaBIOS] : USB 3.0 port failed if a USB 3.0 device is > >> >> attached when power up > >> >> > >> >> 2015-08-07 23:21 GMT+02:00 Kevin O'Connor <kevin(a)koconnor.net>: > >> >> > On Thu, Aug 06, 2015 at 11:51:04AM +0000, Zheng Bao wrote: > >> >> >> Board: Bettong > >> >> >> USB3 controller: Hudson on Carrizo > >> >> >> USB3 device: Seagate USB hard drive. That is the only USB 3.0 device > >> >> >> I > >> >> >> can get. > >> >> > > >> >> > Thanks. The problem looks very similar to one reported in the past by > >> >> > Idwer. Unfortunately, Idwer also didn't have access to any other USB3 > >> >> > devices - that would have been a great test to see if the quirky > >> >> > behavior was due to the controller or due to the device. > >> >> > >> >> The board I have is an Hudson-D4? board, ASUS F2A85-M with the lspci > >> >> ID: > >> >> 00:10.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH > >> >> USB XHCI Controller [1022:7812] (rev 03) > >> >> 00:10.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH > >> >> USB XHCI Controller [1022:7812] (rev 03) > >> >> > >> >> Zheng, can you recompile SeaBIOS with CONFIG_THREADS=y and > >> >> CONFIG_DEBUG_LEVEL=2 and try booting off the superspeed device you're > >> >> using? > >> >> The experience I had was that, with those settings, this superspeed > >> >> SATA dock showed up in the device menu (press ESCape). > >> >> > >> >> If that won't make the device show up - be sure to post that > >> >> cbmem/console output - change USB_TIME_SIGATT in src/hw/usb.h to at > >> >> least 1000. > >> >> > >> >> HTH, > >> >> > >> >> Idwer > >> >> > >> >> > > >> >> > Can you provide the output from "lspci", "lsusb", and "lsusb -t". > >> >> > > >> >> > -Kevin > >> >> > > >> >> >> > >> >> >> Joe > >> >> >> > >> >> >> > Date: Wed, 5 Aug 2015 06:25:13 -0400 > >> >> >> > From: kevin(a)koconnor.net > >> >> >> > To: fishbaoz(a)hotmail.com > >> >> >> > CC: seabios(a)seabios.org > >> >> >> > Subject: Re: [SeaBIOS]: USB 3.0 port failed if a USB 3.0 device is > >> >> >> > attached when power up > >> >> >> > > >> >> >> > On Wed, Aug 05, 2015 at 07:40:50AM +0000, Zheng Bao wrote: > >> >> >> > > hi, Kevin, > >> >> >> > > I am debugging the coreboot on AMD board. > >> >> >> > > > >> >> >> > > I found if a device is populated on USB 3.0 port during system > >> >> >> > > power up, the USB3.0 function fail after OS boot up. > >> >> >> > > If a USB 2.0 device is plugged, the port is OK. > >> >> >> > > Can you take a look at this? > >> >> >> > > >> >> >> > What board is this, what USB3 controller is it, and what USB3 > >> >> >> > device > >> >> >> > did the problem occur with? Does the problem occur with > >> >> >> > multiple/all > >> >> >> > USB3 devices or just one? > >> >> >> > > >> >> >> > -Kevin > >> >> >> > >> >> > >> >> _______________________________________________ > >> >> SeaBIOS mailing list > >> >> SeaBIOS(a)seabios.org > >> >> http://www.seabios.org/mailman/listinfo/seabios > >> > >> _______________________________________________ > >> SeaBIOS mailing list > >> SeaBIOS(a)seabios.org > >> http://www.seabios.org/mailman/listinfo/seabios > > > > _______________________________________________ SeaBIOS mailing list > > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > > > > _______________________________________________ SeaBIOS mailing list > > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > > > > _______________________________________________ SeaBIOS mailing list > > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > > > > _______________________________________________ SeaBIOS mailing list > > SeaBIOS(a)seabios.org http://www.seabios.org/mailman/listinfo/seabios > > _______________________________________________ > SeaBIOS mailing list > SeaBIOS(a)seabios.org > http://www.seabios.org/mailman/listinfo/seabios

3 2

Re: [SeaBIOS] [PATCH] rtc_setup, NMI - Seabios boot loop
by Kevin O'Connor 02 Sep '15

02 Sep '15

On Tue, Sep 01, 2015 at 08:42:00PM +0000, Tim Shearer wrote: [...] > Anyway, rtc_setup() performs several CMOS register reads/writes. The > function that triggers the reset is rtc_mask(). This is the only > routine in the RTC code that doesn't explicitly disable non-maskable > interrupts when writing to the CMOS index register. The patch below > allows everything to boot as it should. Thanks - that does look wrong. I've queued a patch (see below). [...] > This email and attachments may contain privileged or confidential > information intended only for the addressee(s) indicated. [...] Your email was sent to a public email list. -Kevin commit 3156b71a535e6617fbc60fd6aef09a229aca7327 Author: Kevin O'Connor <kevin(a)koconnor.net> Date: Tue Sep 1 19:43:08 2015 -0400 rtc: Disable NMI in rtc_mask() The rtc_mask() function should make sure the NMI disable bit is set (just as rtc_read() and rtc_write() do). Reported-by: Tim Shearer <tim.shearer(a)overturenetworks.com> Signed-off-by: Kevin O'Connor <kevin(a)koconnor.net> diff --git a/src/hw/rtc.c b/src/hw/rtc.c index 570a3ad..9649a5a 100644 --- a/src/hw/rtc.c +++ b/src/hw/rtc.c @@ -30,6 +30,7 @@ rtc_write(u8 index, u8 val) void rtc_mask(u8 index, u8 off, u8 on) { + index |= NMI_DISABLE_BIT; outb(index, PORT_CMOS_INDEX); u8 val = inb(PORT_CMOS_DATA); outb((val & ~off) | on, PORT_CMOS_DATA);

1 0

[PATCH] rtc_setup, NMI - Seabios boot loop
by Tim Shearer 01 Sep '15

01 Sep '15

Hi all, I think I may have found a bug, and would appreciate someone taking a second look. Processor is an Atom C2718, we're using Coreboot 4.0 and booting into Grub and Linux. I have found that making minor/trivial changes in Coreboot (such as configuring an additional pin as a GPIO, or adding a couple of extra lines of debut output) results in the processor rebooting during SeaBIOS' rtc_setup() call. Hard power-cycles work absolutely fine. The problem only occurs after issuing the reboot command from Linux. It's worth noting that our platform doesn't reset the power supplies, so rebooting is basically a "warm" reboot. Also, our RTC isn't battery-backed. Following the reboot, the processor resets each time it reaches rtc_setup(). My best guess so far is that my trivial code changes are subtly changing the boot timing, meaning that by the time I hit the rtc_setup, I have a pending NMI. Anyway, rtc_setup() performs several CMOS register reads/writes. The function that triggers the reset is rtc_mask(). This is the only routine in the RTC code that doesn't explicitly disable non-maskable interrupts when writing to the CMOS index register. The patch below allows everything to boot as it should. Index: src/hw/rtc.c =================================================================== --- a/src/hw/rtc.c +++ b/src/hw/rtc.c @@ -30,7 +30,7 @@ void rtc_mask(u8 index, u8 off, u8 on) { - outb(index, PORT_CMOS_INDEX); + outb(index | NMI_DISABLE_BIT, PORT_CMOS_INDEX); u8 val = inb(PORT_CMOS_DATA); outb((val & ~off) | on, PORT_CMOS_DATA); } Best, Tim This email and attachments may contain privileged or confidential information intended only for the addressee(s) indicated. The sender does not waive any of its rights, privileges or protections respecting this information. If you are not the named addressee, an employee, or agent responsible for sending this message to the named addressee (or this message was received by mistake), you are not authorized to read, print, retain, copy or disseminate this message or any part of it. If received in error, please notify us immediately by e-mail, discard any paper copies and delete all electronic files of the email. Computer viruses can be transmitted via email. The recipient should check this email and any attachments for viruses. Email transmission cannot be guaranteed to be secured or error-free as information could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, or contain viruses. The sender accepts no liability for any damage caused by any transmitted viruses or errors or omissions in the contents of this message. Overture Networks, Inc. 637 Davis Drive, Morrisville, NC USA 27560 www.overturenetworks.com

1 0

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

SeaBIOS September 2015