New subject: Change in coreboot[master]: vendorcode/intel/fsp: Add Jasper Lake FSP headers for FSP v1433

6 Dec 2019

Aamir Bohra has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/37559 )
Change subject: vendorcode/intel/fsp: Add Jasperlake FSP headers for FSP v1433
......................................................................
vendorcode/intel/fsp: Add Jasperlake FSP headers for FSP v1433
Change-Id: Iacb44204c3f7220a20ab3edc2163c97188014bbf
Signed-off-by: Aamir Bohra aamir.bohra@intel.com
---
A src/vendorcode/intel/fsp/fsp2_0/jasperlake/FirmwareVersionInfoHob.h
A src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspUpd.h
A src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspmUpd.h
A src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspsUpd.h
A src/vendorcode/intel/fsp/fsp2_0/jasperlake/FsptUpd.h
A src/vendorcode/intel/fsp/fsp2_0/jasperlake/MemInfoHob.h
6 files changed, 1,869 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/59/37559/1

diff --git a/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FirmwareVersionInfoHob.h b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FirmwareVersionInfoHob.h
new file mode 100644
index 0000000..98a16d7
--- /dev/null
+++ b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FirmwareVersionInfoHob.h
@@ -0,0 +1,68 @@
+/** @file
+  Header file for Firmware Version Information
+
+ @copyright
+  Copyright (c) 2015 - 2018, Intel Corporation. All rights reserved.<BR>
+
+  This program and the accompanying materials are licensed and made available under
+  the terms and conditions of the BSD License which accompanies this distribution.
+  The full text of the license may be found at
+  http://opensource.org/licenses/bsd-license.php
+
+  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+**/
+
+#ifndef _FIRMWARE_VERSION_INFO_HOB_H_
+#define _FIRMWARE_VERSION_INFO_HOB_H_
+
+#include <Uefi/UefiMultiPhase.h>
+#include <Pi/PiBootMode.h>
+#include <Pi/PiHob.h>
+
+#pragma pack(1)
+///
+/// Firmware Version Structure
+///
+typedef struct {
+  UINT8                          MajorVersion;
+  UINT8                          MinorVersion;
+  UINT8                          Revision;
+  UINT16                         BuildNumber;
+} FIRMWARE_VERSION;
+
+///
+/// Firmware Version Information Structure
+///
+typedef struct {
+  UINT8                          ComponentNameIndex;        ///< Offset 0   Index of Component Name
+  UINT8                          VersionStringIndex;        ///< Offset 1   Index of Version String
+  FIRMWARE_VERSION               Version;                   ///< Offset 2-6 Firmware version
+} FIRMWARE_VERSION_INFO;
+
+#ifndef __SMBIOS_STANDARD_H__
+///
+/// The Smbios structure header.
+///
+typedef struct {
+  UINT8                          Type;
+  UINT8                          Length;
+  UINT16                         Handle;
+} SMBIOS_STRUCTURE;
+#endif
+
+///
+/// Firmware Version Information HOB Structure
+///
+typedef struct {
+  EFI_HOB_GUID_TYPE              Header;                    ///< Offset 0-23  The header of FVI HOB
+  SMBIOS_STRUCTURE               SmbiosData;                ///< Offset 24-27  The SMBIOS header of FVI HOB
+  UINT8                          Count;                     ///< Offset 28    Number of FVI elements included.
+///
+/// FIRMWARE_VERSION_INFO structures followed by the null terminated string buffer
+///
+} FIRMWARE_VERSION_INFO_HOB;
+#pragma pack()
+
+#endif // _FIRMWARE_VERSION_INFO_HOB_H_
diff --git a/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspUpd.h b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspUpd.h
new file mode 100644
index 0000000..b28ba78
--- /dev/null
+++ b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspUpd.h
@@ -0,0 +1,48 @@
+/** @file
+
+Copyright (c) 2019, Intel Corporation. All rights reserved.<BR>
+
+Redistribution and use in source and binary forms, with or without modification,
+are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright notice, this
+  list of conditions and the following disclaimer.
+* Redistributions in binary form must reproduce the above copyright notice, this
+  list of conditions and the following disclaimer in the documentation and/or
+  other materials provided with the distribution.
+* Neither the name of Intel Corporation nor the names of its contributors may
+  be used to endorse or promote products derived from this software without
+  specific prior written permission.
+
+  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+  THE POSSIBILITY OF SUCH DAMAGE.
+
+  This file is automatically generated. Please do NOT modify !!!
+
+**/
+
+#ifndef __FSPUPD_H__
+#define __FSPUPD_H__
+
+#include <FspEas.h>
+
+#pragma pack(1)
+
+#define FSPT_UPD_SIGNATURE               0x545F4450554C534A        /* 'JSLUPD_T' */
+
+#define FSPM_UPD_SIGNATURE               0x4D5F4450554C534A        /* 'JSLUPD_M' */
+
+#define FSPS_UPD_SIGNATURE               0x535F4450554C534A        /* 'JSLUPD_S' */
+
+#pragma pack()
+
+#endif
diff --git a/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspmUpd.h b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspmUpd.h
new file mode 100644
index 0000000..cce959c
--- /dev/null
+++ b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspmUpd.h
@@ -0,0 +1,637 @@
+/** @file
+
+Copyright (c) 2019, Intel Corporation. All rights reserved.<BR>
+
+Redistribution and use in source and binary forms, with or without modification,
+are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright notice, this
+  list of conditions and the following disclaimer.
+* Redistributions in binary form must reproduce the above copyright notice, this
+  list of conditions and the following disclaimer in the documentation and/or
+  other materials provided with the distribution.
+* Neither the name of Intel Corporation nor the names of its contributors may
+  be used to endorse or promote products derived from this software without
+  specific prior written permission.
+
+  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+  THE POSSIBILITY OF SUCH DAMAGE.
+
+  This file is automatically generated. Please do NOT modify !!!
+
+**/
+
+#ifndef __FSPMUPD_H__
+#define __FSPMUPD_H__
+
+#include <FspUpd.h>
+
+#pragma pack(1)
+
+
+#include <MemInfoHob.h>
+
+///
+/// The ChipsetInit Info structure provides the information of ME ChipsetInit CRC and BIOS ChipsetInit CRC.
+///
+typedef struct {
+  UINT8             Revision;         ///< Chipset Init Info Revision
+  UINT8             Rsvd[3];          ///< Reserved
+  UINT16            MeChipInitCrc;    ///< 16 bit CRC value of MeChipInit Table
+  UINT16            BiosChipInitCrc;  ///< 16 bit CRC value of PchChipInit Table
+} CHIPSET_INIT_INFO;
+
+
+/** Fsp M Configuration
+**/
+typedef struct {
+
+/** Offset 0x0040 - Reserved
+**/
+  UINT8                      Reserved0[8];
+
+/** Offset 0x0048 - SPD Data Length
+  Length of SPD Data
+  0x100:256 Bytes, 0x200:512 Bytes
+**/
+  UINT16                      MemorySpdDataLen;
+
+/** Offset 0x004A - Reserved
+**/
+  UINT8                       Reserved1[2];
+
+/** Offset 0x004C - Memory SPD Pointer Channel 0 Dimm 0
+  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
+**/
+  UINT32                      MemorySpdPtr00;
+
+/** Offset 0x0050 - Reserved
+**/
+  UINT8                      Reserved2[4];
+
+/** Offset 0x0054 - Memory SPD Pointer Channel 1 Dimm 0
+  Pointer to SPD data, will be used only when SpdAddressTable SPD Address are marked as 00
+**/
+  UINT32                      MemorySpdPtr10;
+
+/** Offset 0x0058 - Reserved
+**/
+  UINT8                      Reserved3[4];
+
+/** Offset 0x005C - Dq Byte Map CH0
+  Dq byte mapping between CPU and DRAM, Channel 0: board-dependent
+**/
+  UINT8                       DqByteMapCh0[12];
+
+/** Offset 0x0068 - Dq Byte Map CH1
+  Dq byte mapping between CPU and DRAM, Channel 1: board-dependent
+**/
+  UINT8                       DqByteMapCh1[12];
+
+/** Offset 0x0074 - Dqs Map CPU to DRAM CH 0
+  Set Dqs mapping relationship between CPU and DRAM, Channel 0: board-dependent
+**/
+  UINT8                       DqsMapCpu2DramCh0[8];
+
+/** Offset 0x007C - Dqs Map CPU to DRAM CH 1
+  Set Dqs mapping relationship between CPU and DRAM, Channel 1: board-dependent
+**/
+  UINT8                       DqsMapCpu2DramCh1[8];
+
+/** Offset 0x0084 - RcompResister settings
+  Indicates  RcompReister settings: Board-dependent
+**/
+  UINT16                      RcompResistor[3];
+
+/** Offset 0x008A - RcompTarget settings
+  RcompTarget settings: board-dependent
+**/
+  UINT16                      RcompTarget[5];
+
+/** Offset 0x0094 - Dqs Pins Interleaved Setting
+  Indicates DqPinsInterleaved setting: board-dependent
+  $EN_DIS
+**/
+  UINT8                       DqPinsInterleaved;
+
+/** Offset 0x0095 - VREF_CA
+  CA Vref routing: board-dependent
+  0:VREF_CA goes to both CH_A and CH_B, 1: VREF_CA to CH_A and VREF_DQ_A to CH_B,
+  2:VREF_CA to CH_A and VREF_DQ_B to CH_B
+**/
+  UINT8                       CaVrefConfig;
+
+/** Offset 0x0096 - Reserved
+**/
+  UINT8                       Reserved4[6];
+
+/** Offset 0x009C - Intel Enhanced Debug
+  Intel Enhanced Debug (IED): 0=Disabled, 0x400000=Enabled and 4MB SMRAM occupied
+  0 : Disable, 0x400000 : Enable
+**/
+  UINT32                      IedSize;
+
+/** Offset 0x00A0 - Tseg Size
+  Size of SMRAM memory reserved. 0x400000 for Release build and 0x1000000 for Debug build
+  0x0400000:4MB, 0x01000000:16MB
+**/
+  UINT32                      TsegSize;
+
+/** Offset 0x00A4 - Reserved
+**/
+  UINT8                      Reserved5[6];
+
+/** Offset 0x00AA - Enable SMBus
+  Enable/disable SMBus controller.
+  $EN_DIS
+**/
+  UINT8                       SmbusEnable;
+
+/** Offset 0x00AB - Spd Address Tabl
+  Specify SPD Address table for CH0D0/CH0D1/CH1D0&CH1D1. MemorySpdPtr will be used
+  if SPD Address is 00
+**/
+  UINT8                       SpdAddressTable[4];
+
+/** Offset 0x00AF - Platform Debug Consent
+  To 'opt-in' for debug, please select 'Enabled' with the desired debug probe type.
+  Enabling this BIOS option may alter the default value of other debug-related BIOS
+  options.\Manual: Do not use Platform Debug Consent to override other debug-relevant
+  policies, but the user must set each debug option manually, aimed at advanced users.\n
+  Note: DCI OOB (aka BSSB) uses CCA probe.
+  0:Disabled, 2:Enabled (DCI OOB), 3:Enabled (USB3 DbC), 4:Enabled (XDP/MIPI60), 5:Enabled
+  (USB2 DbC), 6:Enable (2-wire DCI OOB), 7:Manual
+**/
+  UINT8                       PlatformDebugConsent;
+
+/** Offset 0x00B0 - Reserved
+**/
+  UINT8                       Reserved6[2];
+
+/** Offset 0x00B2 - Enable DCI ModPHY Pwoer Gate
+  Enable ModPHY Pwoer Gate when DCI is enabled
+  $EN_DIS
+**/
+  UINT8                       DciModphyPg;
+
+/** Offset 0x00B3 - Reserved
+**/
+  UINT8                       Reserved7;
+
+/** Offset 0x00B4 - PCH Trace Hub Mode
+  Select 'Host Debugger' if Trace Hub is used with host debugger tool or 'Target Debugger'
+  if Trace Hub is used by target debugger software or 'Disable' trace hub functionality.
+  0: Disable, 1: Target Debugger Mode, 2: Host Debugger Mode
+**/
+  UINT8                       PchTraceHubMode;
+
+/** Offset 0x00B5 - Reserved
+**/
+  UINT8                       Reserved8[47];
+
+/** Offset 0x00E4 - Disable VT-d
+  0=Enable/FALSE(VT-d enabled), 1=Disable/TRUE (VT-d disabled)
+  $EN_DIS
+**/
+  UINT8                       VtdDisable;
+
+/** Offset 0x00E5 - Reserved
+**/
+  UINT8                       Reserved9[3];
+
+/** Offset 0x00E8 - Internal Graphics Pre-allocated Memory
+  Size of memory preallocated for internal graphics.
+  0x00:0MB, 0x01:32MB, 0x02:64MB, 0x03:96MB, 0x04:128MB, 0x05:160MB, 0xF0:4MB, 0xF1:8MB,
+  0xF2:12MB, 0xF3:16MB, 0xF4:20MB, 0xF5:24MB, 0xF6:28MB, 0xF7:32MB, 0xF8:36MB, 0xF9:40MB,
+  0xFA:44MB, 0xFB:48MB, 0xFC:52MB, 0xFD:56MB, 0xFE:60MB
+**/
+  UINT8                       IgdDvmt50PreAlloc;
+
+/** Offset 0x00E9 - Internal Graphics
+  Enable/disable internal graphics.
+  $EN_DIS
+**/
+  UINT8                       InternalGfx;
+
+/** Offset 0x00EA - Reserved
+**/
+  UINT8                       Reserved10;
+
+/** Offset 0x00EB - Board Type
+  MrcBoardType, Options are 0=Mobile/Mobile Halo, 1=Desktop/DT Halo, 5=ULT/ULX/Mobile
+  Halo, 7=UP Server
+  0:Mobile/Mobile Halo, 1:Desktop/DT Halo, 5:ULT/ULX/Mobile Halo, 7:UP Server
+**/
+  UINT8                       UserBd;
+
+/** Offset 0x00EC - Reserved
+**/
+  UINT8                      Reserved11[2];
+
+/** Offset 0x00EE - SA GV
+  System Agent dynamic frequency support and when enabled memory will be training
+  at three different frequencies.
+  0:Disabled, 1:FixedLow, 2:FixedMid, 3:FixedHigh, 4:Enabled
+**/
+  UINT8                       SaGv;
+
+/** Offset 0x00EF - Reserved
+**/
+  UINT8                       Reserved12[5];
+
+/** Offset 0x00F4 - Rank Margin Tool
+  Enable/disable Rank Margin Tool.
+  $EN_DIS
+**/
+  UINT8                       RMT;
+
+/** Offset 0x00F5 - Reserved
+**/
+  UINT8                       Reserved13[24];
+
+/** Offset 0x010D - Memory Reference Clock
+  100MHz, 133MHz.
+  0:133MHz, 1:100MHz
+**/
+  UINT8                       RefClk;
+
+/** Offset 0x010E - Reserved
+**/
+  UINT8                      Reserved14[26];
+
+/** Offset 0x0128 - Enable Intel HD Audio (Azalia)
+  0: Disable, 1: Enable (Default) Azalia controller
+  $EN_DIS
+**/
+  UINT8                       PchHdaEnable;
+
+/** Offset 0x0129 - CPU Trace Hub Mode
+  Select 'Host Debugger' if Trace Hub is used with host debugger tool or 'Target Debugger'
+  if Trace Hub is used by target debugger software or 'Disable' trace hub functionality.
+  0: Disable, 1:Target Debugger Mode, 2:Host Debugger Mode
+**/
+  UINT8                       CpuTraceHubMode;
+
+/** Offset 0x012A - Reserved
+**/
+  UINT8                       Reserved15[98];
+
+/** Offset 0x018C - Program GPIOs for LFP on DDI port-A device
+  0=Disabled,1(Default)=eDP, 2=MIPI DSI
+  0:Disabled, 1:eDP, 2:MIPI DSI
+**/
+  UINT8                       DdiPortAConfig;
+
+/** Offset 0x018D - Reserved
+**/
+  UINT8                       Reserved16[2];
+
+/** Offset 0x018F - Enable or disable HPD of DDI port B
+  0=Disable, 1(Default)=Enable
+  $EN_DIS
+**/
+  UINT8                       DdiPortBHpd;
+
+/** Offset 0x0190 - Enable or disable HPD of DDI port C
+  0(Default)=Disable, 1=Enable
+  $EN_DIS
+**/
+  UINT8                       DdiPortCHpd;
+
+/** Offset 0x0191 - Reserved
+**/
+  UINT8                       Reserved17[5];
+
+/** Offset 0x0196 - Enable or disable DDC of DDI port B
+  0=Disable, 1(Default)=Enable
+  $EN_DIS
+**/
+  UINT8                       DdiPortBDdc;
+
+/** Offset 0x0197 - Enable or disable DDC of DDI port C
+  0(Default)=Disable, 1=Enable
+  $EN_DIS
+**/
+  UINT8                       DdiPortCDdc;
+
+/** Offset 0x0198 - Reserved
+**/
+  UINT8                       Reserved18[165];
+
+/** Offset 0x023D - C6DRAM power gating feature
+  This policy indicates whether or not BIOS should allocate PRMRR memory for C6DRAM
+  power gating feature.- 0: Don't allocate any PRMRR memory for C6DRAM power gating
+  feature.- <b>1: Allocate PRMRR memory for C6DRAM power gating feature</b>.
+  $EN_DIS
+**/
+  UINT8                       EnableC6Dram;
+
+/** Offset 0x023E - Reserved
+**/
+  UINT8                       Reserved19[7];
+
+/** Offset 0x0245 - CPU ratio value
+  CPU ratio value. Valid Range 0 to 63
+**/
+  UINT8                       CpuRatio;
+
+/** Offset 0x0246 - Reserved
+**/
+  UINT8                       Reserved20[4];
+
+/** Offset 0x024A - Enable or Disable VMX
+  Enable or Disable VMX; 0: Disable; <b>1: Enable</b>.
+  $EN_DIS
+**/
+  UINT8                       VmxEnable;
+
+/** Offset 0x024B - Reserved
+**/
+  UINT8                       Reserved21[31];
+
+/** Offset 0x026A - BiosGuard
+  Enable/Disable. 0: Disable, Enable/Disable BIOS Guard feature, 1: enable
+  $EN_DIS
+**/
+  UINT8                       BiosGuard;
+
+/** Offset 0x026B - Reserved
+**/
+  UINT8                       Reserved22[5];
+
+/** Offset 0x0270 - PrmrrSize
+  Enable/Disable. 0: Disable, define default value of PrmrrSize , 1: enable
+**/
+  UINT32                      PrmrrSize;
+
+/** Offset 0x0274 - SinitMemorySize
+  Enable/Disable. 0: Disable, define default value of SinitMemorySize , 1: enable
+**/
+  UINT32                      SinitMemorySize;
+
+/** Offset 0x0278 - Reserved
+**/
+  UINT8                      Reserved23[543];
+
+/** Offset 0x0497 - Usage type for ClkSrc
+  0-23: PCH rootport, 0x40-0x43: PEG port, 0x70:LAN, 0x80: unspecified but in use
+  (free running), 0xFF: not used
+**/
+  UINT8                       PcieClkSrcUsage[16];
+
+/** Offset 0x04A7 - ClkReq-to-ClkSrc mapping
+  Number of ClkReq signal assigned to ClkSrc
+**/
+  UINT8                       PcieClkSrcClkReq[16];
+
+/** Offset 0x04B7 - Reserved
+**/
+  UINT8                       Reserved24[5];
+
+/** Offset 0x04BC - Enable PCIE RP Mask
+  Enable/disable PCIE Root Ports. 0: disable, 1: enable. One bit for each port, bit0
+  for port1, bit1 for port2, and so on.
+**/
+  UINT32                      PcieRpEnableMask;
+
+/** Offset 0x04C0 - Debug Interfaces
+  Debug Interfaces. BIT0-RAM, BIT1-UART, BIT3-USB3, BIT4-Serial IO, BIT5-TraceHub,
+  BIT2 - Not used.
+**/
+  UINT8                       PcdDebugInterfaceFlags;
+
+/** Offset 0x04C1 - Serial Io Uart Debug Controller Number
+  Select SerialIo Uart Controller for debug. Note: If UART0 is selected as CNVi BT
+  Core interface, it cannot be used for debug purpose.
+  0:SerialIoUart0, 1:SerialIoUart1, 2:SerialIoUart2
+**/
+  UINT8                       SerialIoUartDebugControllerNumber;
+
+/** Offset 0x04C2 - Reserved
+**/
+  UINT8                       Reserved25[22];
+
+/** Offset 0x04D8 - Early Command Training
+  Enables/Disable Early Command Training
+  $EN_DIS
+**/
+  UINT8                       ECT;
+
+/** Offset 0x04D9 - Reserved
+**/
+  UINT8                       Reserved26[2];
+
+/** Offset 0x04DB - Read MPR Training
+  Enables/Disable Read MPR Training
+  $EN_DIS
+**/
+  UINT8                       RDMPRT;
+
+/** Offset 0x04DC - Reserved
+**/
+  UINT8                       Reserved27[7];
+
+/** Offset 0x04E3 - Dimm ODT Training
+  Enables/Disable Dimm ODT Training
+  $EN_DIS
+**/
+  UINT8                       DIMMODTT;
+
+/** Offset 0x04E4 - DIMM RON Training
+  Enables/Disable DIMM RON Training
+  $EN_DIS
+**/
+  UINT8                       DIMMRONT;
+
+/** Offset 0x04E5 - Reserved
+**/
+  UINT8                       Reserved28;
+
+/** Offset 0x04E6 - Write Slew Rate Training
+  Enables/Disable Write Slew Rate Training
+  $EN_DIS
+**/
+  UINT8                       WRSRT;
+
+/** Offset 0x04E7 - Read ODT Training
+  Enables/Disable Read ODT Training
+  $EN_DIS
+**/
+  UINT8                       RDODTT;
+
+/** Offset 0x04E8 - Read Equalization Training
+  Enables/Disable Read Equalization Training
+  $EN_DIS
+**/
+  UINT8                       RDEQT;
+
+/** Offset 0x04E9 - Read Amplifier Training
+  Enables/Disable Read Amplifier Training
+  $EN_DIS
+**/
+  UINT8                       RDAPT;
+
+/** Offset 0x04EA - Reserved
+**/
+  UINT8                       Reserved29[3];
+
+/** Offset 0x04ED - Read Voltage Centering 2D
+  Enables/Disable Read Voltage Centering 2D
+  $EN_DIS
+**/
+  UINT8                       RDVC2D;
+
+/** Offset 0x04EE - Reserved
+**/
+  UINT8                       Reserved30[3];
+
+/** Offset 0x04F1 - Turn Around Timing Training
+  Enables/Disable Turn Around Timing Training
+  $EN_DIS
+**/
+  UINT8                       TAT;
+
+/** Offset 0x04F2 - Reserved
+**/
+  UINT8                       Reserved31[6];
+
+/** Offset 0x04F8 - Receive Enable Centering 1D
+  Enables/Disable Receive Enable Centering 1D
+  $EN_DIS
+**/
+  UINT8                       RCVENC1D;
+
+/** Offset 0x04F9 - Retrain Margin Check
+  Enables/Disable Retrain Margin Check
+  $EN_DIS
+**/
+  UINT8                       RMC;
+
+/** Offset 0x04FA - Reserved
+**/
+  UINT8                       Reserved32[60];
+
+/** Offset 0x0536 - RAPL PL 1 WindowX
+  Power PL 1 time window X value, (1/1024)*(1+(x/4))*(2^y) (0=Def)
+**/
+  UINT8                       RaplLim1WindX;
+
+/** Offset 0x0537 - RAPL PL 1 WindowY
+  Power PL 1 time window Y value, (1/1024)*(1+(x/4))*(2^y) (0=Def)
+**/
+  UINT8                       RaplLim1WindY;
+
+/** Offset 0x0538 - Reserved
+**/
+  UINT8                      Reserved33[2];
+
+/** Offset 0x053A - RAPL PL 1 Power
+  range[0;2^14-1]= [2047.875;0]in W, (224= Def)
+**/
+  UINT16                      RaplLim1Pwr;
+
+/** Offset 0x053C - Reserved
+**/
+  UINT8                       Reserved34[68];
+
+/** Offset 0x0580 - LpDdrDqDqsReTraining
+  Enables/Disable LpDdrDqDqsReTraining
+  $EN_DIS
+**/
+  UINT8                       LpDdrDqDqsReTraining;
+
+/** Offset 0x0581 - Reserved
+**/
+  UINT8                       Reserved35[172];
+
+/** Offset 0x062D - Enable HD Audio Link
+  Enable/disable HD Audio Link. Muxed with SSP0/SSP1/SNDW1.
+  $EN_DIS
+**/
+  UINT8                       PchHdaAudioLinkHdaEnable;
+
+/** Offset 0x062E - Reserved
+**/
+  UINT8                       Reserved36[3];
+
+/** Offset 0x0631 - Enable HD Audio DMIC_N Link
+  Enable/disable HD Audio DMIC1 link. Muxed with SNDW3.
+**/
+  UINT8                       PchHdaAudioLinkDmicEnable[2];
+
+/** Offset 0x0633 - Reserved
+**/
+  UINT8                       Reserved37[17];
+
+/** Offset 0x0644 - Enable HD Audio DSP
+  Enable/disable HD Audio DSP feature.
+  $EN_DIS
+**/
+  UINT8                       PchHdaDspEnable;
+
+/** Offset 0x0645 - Reserved
+**/
+  UINT8                       Reserved38[11];
+
+/** Offset 0x0650 - Enable HD Audio SSP0 Link
+  Enable/disable HD Audio SSP_N/I2S link. Muxed with HDA. N-number 0-5
+**/
+  UINT8                       PchHdaAudioLinkSspEnable[6];
+
+/** Offset 0x0656 - Enable HD Audio SoundWire#N Link
+  Enable/disable HD Audio SNDW#N link. Muxed with HDA.
+**/
+  UINT8                       PchHdaAudioLinkSndwEnable[4];
+
+/** Offset 0x065A - Reserved
+**/
+  UINT8                       Reserved39[7];
+
+/** Offset 0x0661 - Skip MBP HOB
+  Test, 0: disable, 1: enable, Enable/Disable MOB HOB.
+  $EN_DIS
+**/
+  UINT8                       SkipMbpHob;
+
+/** Offset 0x0662 - Reserved
+**/
+  UINT8                       Reserved40[22];
+} FSP_M_CONFIG;
+
+/** Fsp M UPD Configuration
+**/
+typedef struct {
+
+/** Offset 0x0000
+**/
+  FSP_UPD_HEADER              FspUpdHeader;
+
+/** Offset 0x0020
+**/
+  FSPM_ARCH_UPD               FspmArchUpd;
+
+/** Offset 0x0040
+**/
+  FSP_M_CONFIG                FspmConfig;
+
+/** Offset 0x0678
+**/
+  UINT8                       UnusedUpdSpace19[6];
+
+/** Offset 0x067E
+**/
+  UINT16                      UpdTerminator;
+} FSPM_UPD;
+
+#pragma pack()
+
+#endif
diff --git a/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspsUpd.h b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspsUpd.h
new file mode 100644
index 0000000..d01ae6a
--- /dev/null
+++ b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FspsUpd.h
@@ -0,0 +1,656 @@
+/** @file
+
+Copyright (c) 2019, Intel Corporation. All rights reserved.<BR>
+
+Redistribution and use in source and binary forms, with or without modification,
+are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright notice, this
+  list of conditions and the following disclaimer.
+* Redistributions in binary form must reproduce the above copyright notice, this
+  list of conditions and the following disclaimer in the documentation and/or
+  other materials provided with the distribution.
+* Neither the name of Intel Corporation nor the names of its contributors may
+  be used to endorse or promote products derived from this software without
+  specific prior written permission.
+
+  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+  THE POSSIBILITY OF SUCH DAMAGE.
+
+  This file is automatically generated. Please do NOT modify !!!
+
+**/
+
+#ifndef __FSPSUPD_H__
+#define __FSPSUPD_H__
+
+#include <FspUpd.h>
+
+#pragma pack(1)
+
+
+///
+/// Azalia Header structure
+///
+typedef struct {
+  UINT16 VendorId;           ///< Codec Vendor ID
+  UINT16 DeviceId;           ///< Codec Device ID
+  UINT8  RevisionId;         ///< Revision ID of the codec. 0xFF matches any revision.
+  UINT8  SdiNum;             ///< SDI number, 0xFF matches any SDI.
+  UINT16 DataDwords;         ///< Number of data DWORDs pointed by the codec data buffer.
+  UINT32 Reserved;           ///< Reserved for future use. Must be set to 0.
+} AZALIA_HEADER;
+
+///
+/// Audio Azalia Verb Table structure
+///
+typedef struct {
+  AZALIA_HEADER Header;      ///< AZALIA PCH header
+  UINT32        *Data;       ///< Pointer to the data buffer. Its length is specified in the header
+} AUDIO_AZALIA_VERB_TABLE;
+
+///
+/// Refer to the definition of PCH_INT_PIN
+///
+typedef enum {
+  SiPchNoInt,        ///< No Interrupt Pin
+  SiPchIntA,
+  SiPchIntB,
+  SiPchIntC,
+  SiPchIntD
+} SI_PCH_INT_PIN;
+///
+/// The PCH_DEVICE_INTERRUPT_CONFIG block describes interrupt pin, IRQ and interrupt mode for PCH device.
+///
+typedef struct {
+  UINT8        Device;                  ///< Device number
+  UINT8        Function;                ///< Device function
+  UINT8        IntX;                    ///< Interrupt pin: INTA-INTD (see SI_PCH_INT_PIN)
+  UINT8        Irq;                     ///< IRQ to be set for device.
+} SI_PCH_DEVICE_INTERRUPT_CONFIG;
+
+#define SI_PCH_MAX_DEVICE_INTERRUPT_CONFIG  64       ///< Number of all PCH devices
+
+
+/** Fsp S Configuration
+**/
+typedef struct {
+
+/** Offset 0x0020 - Reserved
+**/
+  UINT8                      Reserved0[16];
+
+/** Offset 0x0030 - Graphics Configuration Ptr
+  Points to VBT
+**/
+  UINT32                      GraphicsConfigPtr;
+
+/** Offset 0x0034 - Enable Device 4
+  Enable/disable Device 4
+  $EN_DIS
+**/
+  UINT8                       Device4Enable;
+
+/** Offset 0x0035 - Enable eMMC Controller
+  Enable/disable eMMC Controller.
+  $EN_DIS
+**/
+  UINT8                       ScsEmmcEnabled;
+
+/** Offset 0x0036 - Enable eMMC HS400 Mode
+  Enable eMMC HS400 Mode.
+  $EN_DIS
+**/
+  UINT8                       ScsEmmcHs400Enabled;
+
+/** Offset 0x0037 - Use DLL values from policy
+  Set if FSP should use HS400 DLL values from policy
+  $EN_DIS
+**/
+  UINT8                       EmmcUseCustomDlls;
+
+/** Offset 0x0038 - Emmc Tx CMD Delay control register value
+  Please see Tx CMD Delay Control register definition for help
+**/
+  UINT32                      EmmcTxCmdDelayRegValue;
+
+/** Offset 0x003C - Emmc Tx DATA Delay control 1 register value
+  Please see Tx DATA Delay control 1 register definition for help
+**/
+  UINT32                      EmmcTxDataDelay1RegValue;
+
+/** Offset 0x0040 - Emmc Tx DATA Delay control 2 register value
+  Please see Tx DATA Delay control 2 register definition for help
+**/
+  UINT32                      EmmcTxDataDelay2RegValue;
+
+/** Offset 0x0044 - Emmc Rx CMD + DATA Delay control 1 register value
+  Please see Rx CMD + DATA Delay control 1 register definition for help
+**/
+  UINT32                      EmmcRxCmdDataDelay1RegValue;
+
+/** Offset 0x0048 - Emmc Rx CMD + DATA Delay control 2 register value
+  Please see Rx CMD + DATA Delay control 2 register definition for help
+**/
+  UINT32                      EmmcRxCmdDataDelay2RegValue;
+
+/** Offset 0x004C - Emmc Rx Strobe Delay control register value
+  Please see Rx Strobe Delay control register definition for help
+**/
+  UINT32                      EmmcRxStrobeDelayRegValue;
+
+/** Offset 0x0050 - Enable SdCard Controller
+  Enable/disable SD Card Controller.
+  $EN_DIS
+**/
+  UINT8                       ScsSdCardEnabled;
+
+/** Offset 0x0051 - SdCard power enable polarity
+  Choose SD_PWREN# polarity
+  0: Active low, 1: Active high
+**/
+  UINT8                       SdCardPowerEnableActiveHigh;
+
+/** Offset 0x0052 - Reserved
+**/
+  UINT8                       Reserved1[34];
+
+/** Offset 0x0074 - SdCard Command Pad Termination
+  0x0: Hardware default, 0x1: None, 0x13: 1kOhm weak pull-up, 0x15: 5kOhm weak pull-up,
+  0x19: 20kOhm weak pull-up
+**/
+  UINT8                       SdCardGpioCmdPadTermination;
+
+/** Offset 0x0075 - Reserved
+**/
+  UINT8                       Reserved2[136];
+
+/** Offset 0x00FD - Enable SATA SALP Support
+  Enable/disable SATA Aggressive Link Power Management.
+  $EN_DIS
+**/
+  UINT8                       SataSalpSupport;
+
+/** Offset 0x00FE - Enable SATA ports
+  Enable/disable SATA ports. One byte for each port, byte0 for port0, byte1 for port1,
+  and so on.
+**/
+  UINT8                       SataPortsEnable[8];
+
+/** Offset 0x0106 - Enable SATA DEVSLP Feature
+  Enable/disable SATA DEVSLP per port. 0 is disable, 1 is enable. One byte for each
+  port, byte0 for port0, byte1 for port1, and so on.
+**/
+  UINT8                       SataPortsDevSlp[8];
+
+/** Offset 0x010E - Enable USB2 ports
+  Enable/disable per USB2 ports. One byte for each port, byte0 for port0, byte1 for
+  port1, and so on.
+**/
+  UINT8                       PortUsb20Enable[16];
+
+/** Offset 0x011E - Enable USB3 ports
+  Enable/disable per USB3 ports. One byte for each port, byte0 for port0, byte1 for
+  port1, and so on.
+**/
+  UINT8                       PortUsb30Enable[10];
+
+/** Offset 0x0128 - Enable xDCI controller
+  Enable/disable to xDCI controller.
+  $EN_DIS
+**/
+  UINT8                       XdciEnable;
+
+/** Offset 0x0129 - Reserved
+**/
+  UINT8                       Reserved3[28];
+
+/** Offset 0x0145 - Enable SATA
+  Enable/disable SATA controller.
+  $EN_DIS
+**/
+  UINT8                       SataEnable;
+
+/** Offset 0x0146 - SATA Mode
+  Select SATA controller working mode.
+  0:AHCI, 1:RAID
+**/
+  UINT8                       SataMode;
+
+/** Offset 0x0147 - SPIn Device Mode
+  Selects SPI operation mode. N represents controller index: SPI0, SPI1, ... Available
+  modes: 0:SerialIoSpiDisabled, 1:SerialIoSpiPci, 2:SerialIoSpiHidden
+**/
+  UINT8                       SerialIoSpiMode[7];
+
+/** Offset 0x014E - SPI<N> Chip Select Polarity
+  Sets polarity for each chip Select. Available options: 0:SerialIoSpiCsActiveLow,
+  1:SerialIoSpiCsActiveHigh
+**/
+  UINT8                       SerialIoSpiCsPolarity[14];
+
+/** Offset 0x015C - Reserved
+**/
+  UINT8                       Reserved4[21];
+
+/** Offset 0x0171 - SPIn Default Chip Select Mode HW/SW
+  Sets Default CS Mode Hardware or Software. N represents controller index: SPI0,
+  SPI1, ... Available options: 0:HW, 1:SW
+**/
+  UINT8                       SerialIoSpiCsMode[7];
+
+/** Offset 0x0178 - SPIn Default Chip Select State Low/High
+  Sets Default CS State Low or High. N represents controller index: SPI0, SPI1, ...
+  Available options: 0:Low, 1:High
+**/
+  UINT8                       SerialIoSpiCsState[7];
+
+/** Offset 0x017F - UARTn Device Mode
+  Selects Uart operation mode. N represents controller index: Uart0, Uart1, ... Available
+  modes: 0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
+  4:SerialIoUartSkipInit
+**/
+  UINT8                       SerialIoUartMode[7];
+
+/** Offset 0x0186 - Reserved
+**/
+  UINT8                       Reserved5[186];
+
+/** Offset 0x0240 - UART Number For Debug Purpose
+  UART number for debug purpose. 0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5,
+  6:UART6. Note: If UART0 is selected as CNVi BT Core interface, it cannot be used
+  for debug purpose.
+   0:UART0, 1:UART1, 2:UART2, 3:UART3, 4:UART4, 5:UART5, 6:UART6
+**/
+  UINT8                       SerialIoDebugUartNumber;
+
+/** Offset 0x0241 - Reserved
+**/
+  UINT8                       Reserved6[7];
+
+/** Offset 0x0248 - I2Cn Device Mode
+  Selects I2c operation mode. N represents controller index: I2c0, I2c1, ... Available
+  modes: 0:SerialIoI2cDisabled, 1:SerialIoI2cPci, 2:SerialIoI2cHidden
+**/
+  UINT8                       SerialIoI2cMode[8];
+
+/** Offset 0x0250 - Reserved
+**/
+  UINT8                      Reserved7[72];
+
+/** Offset 0x0298 - USB Per Port HS Preemphasis Bias
+  USB Per Port HS Preemphasis Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
+  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV. One byte for each port.
+**/
+  UINT8                       Usb2PhyPetxiset[16];
+
+/** Offset 0x02A8 - USB Per Port HS Transmitter Bias
+  USB Per Port HS Transmitter Bias. 000b-0mV, 001b-11.25mV, 010b-16.9mV, 011b-28.15mV,
+  100b-28.15mV, 101b-39.35mV, 110b-45mV, 111b-56.3mV, One byte for each port.
+**/
+  UINT8                       Usb2PhyTxiset[16];
+
+/** Offset 0x02B8 - USB Per Port HS Transmitter Emphasis
+  USB Per Port HS Transmitter Emphasis. 00b - Emphasis OFF, 01b - De-emphasis ON,
+  10b - Pre-emphasis ON, 11b - Pre-emphasis & De-emphasis ON. One byte for each port.
+**/
+  UINT8                       Usb2PhyPredeemp[16];
+
+/** Offset 0x02C8 - USB Per Port Half Bit Pre-emphasis
+  USB Per Port Half Bit Pre-emphasis. 1b - half-bit pre-emphasis, 0b - full-bit pre-emphasis.
+  One byte for each port.
+**/
+  UINT8                       Usb2PhyPehalfbit[16];
+
+/** Offset 0x02D8 - Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment
+  Enable the write to USB 3.0 TX Output -3.5dB De-Emphasis Adjustment. Each value
+  in arrary can be between 0-1. One byte for each port.
+**/
+  UINT8                       Usb3HsioTxDeEmphEnable[10];
+
+/** Offset 0x02E2 - USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting
+  USB 3.0 TX Output -3.5dB De-Emphasis Adjustment Setting, HSIO_TX_DWORD5[21:16],
+  <b>Default = 29h</b> (approximately -3.5dB De-Emphasis). One byte for each port.
+**/
+  UINT8                       Usb3HsioTxDeEmph[10];
+
+/** Offset 0x02EC - Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment
+  Enable the write to USB 3.0 TX Output Downscale Amplitude Adjustment, Each value
+  in arrary can be between 0-1. One byte for each port.
+**/
+  UINT8                       Usb3HsioTxDownscaleAmpEnable[10];
+
+/** Offset 0x02F6 - USB 3.0 TX Output Downscale Amplitude Adjustment
+  USB 3.0 TX Output Downscale Amplitude Adjustment, HSIO_TX_DWORD8[21:16], <b>Default
+  = 00h</b>. One byte for each port.
+**/
+  UINT8                       Usb3HsioTxDownscaleAmp[10];
+
+/** Offset 0x0300 - Enable LAN
+  Enable/disable LAN controller.
+  $EN_DIS
+**/
+  UINT8                       PchLanEnable;
+
+/** Offset 0x0301 - Reserved
+**/
+  UINT8                       Reserved8[83];
+
+/** Offset 0x0354 - External V1P05 Voltage Value that will be used in S0i2/S0i3 states
+  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
+**/
+  UINT16                      PchFivrExtV1p05RailVoltage;
+
+/** Offset 0x0356 - External V1P05 Icc Max Value
+  Granularity of this setting is 1mA and maximal possible value is 200mA
+**/
+  UINT8                       PchFivrExtV1p05RailIccMax;
+
+/** Offset 0x0357 - Reserved
+**/
+  UINT8                       Reserved9;
+
+/** Offset 0x0358 - External Vnn Voltage Value that will be used in S0ix/Sx states
+  Value is given in 2.5mV increments (0=0mV, 1=2.5mV, 2=5mV...)
+**/
+  UINT16                      PchFivrExtVnnRailVoltage;
+
+/** Offset 0x035A - External Vnn Icc Max Value that will be used in S0ix/Sx states
+  Granularity of this setting is 1mA and maximal possible value is 200mA
+**/
+  UINT8                       PchFivrExtVnnRailIccMax;
+
+/** Offset 0x035B - Reserved
+**/
+  UINT8                       Reserved10;
+
+/** Offset 0x035C - External Vnn Voltage Value that will be used in Sx states
+  Use only if Ext Vnn Rail config is different in Sx. Value is given in 2.5mV increments
+  (0=0mV, 1=2.5mV, 2=5mV...)
+**/
+  UINT16                      PchFivrExtVnnRailSxVoltage;
+
+/** Offset 0x035E - External Vnn Icc Max Value that will be used in Sx states
+  Use only if Ext Vnn Rail config is different in Sx. Granularity of this setting
+  is 1mA and maximal possible value is 200mA
+**/
+  UINT8                       PchFivrExtVnnRailSxIccMax;
+
+/** Offset 0x035F - Reserved
+**/
+  UINT8                       Reserved11[3];
+
+/** Offset 0x0362 - Transition time in microseconds from Off (0V) to High Current Mode Voltage
+  This field has 1us resolution. When value is 0 Transition to 0V is disabled.
+**/
+  UINT16                      PchFivrVccinAuxOffToHighCurModeVolTranTime;
+
+/** Offset 0x0364 - Reserved
+**/
+  UINT8                      Reserved12[22];
+
+/** Offset 0x037A - CNVi BT Audio Offload
+  Enable/Disable BT Audio Offload, Default is DISABLE. 0: DISABLE, 1: ENABLE
+  $EN_DIS
+**/
+  UINT8                       CnviBtAudioOffload;
+
+/** Offset 0x037B - Reserved
+**/
+  UINT8                       Reserved13;
+
+/** Offset 0x037C - CNVi RF_RESET pin muxing
+  Select CNVi RF_RESET# pin depending on board routing. ICP-N: GPP_H12 = 0x2746E40C(default)
+  or GPP_H1 = 0x3746E401. Refer to GPIO_*_MUXING_CNVI_RF_RESET_* in GpioPins*.h.
+**/
+  UINT32                      CnviRfResetPinMux;
+
+/** Offset 0x0380 - CNVi CLKREQ pin muxing
+  Select CNVi CLKREQ pin depending on board routing. ICP-N: GPP_H13 = 0x2746E60D(default)
+  or GPP_H2 = 0x3746E602. Refer to GPIO_*_MUXING_CNVI_MODEM_CLKREQ_* in GpioPins*.h.
+**/
+  UINT32                      CnviClkreqPinMux;
+
+/** Offset 0x0384 - Reserved
+**/
+  UINT8                       Reserved14[6];
+
+/** Offset 0x038A - HECI3 state
+  The HECI3 state from Mbp for reference in S3 path or when MbpHob is not installed.
+  0: disable, 1: enable
+  $EN_DIS
+**/
+  UINT8                       Heci3Enabled;
+
+/** Offset 0x038B - Reserved
+**/
+  UINT8                       Reserved15[141];
+
+/** Offset 0x0418 - CdClock Frequency selection
+  0: (Default) Auto (Max based on reference clock frequency), 1: 172.8 Mhz, 2: 180
+  Mhz, 3: 190 Mhz, 4: 307.2 Mhz, 5: 312 Mhz, 6: 552 Mhz, 7: 556.8 Mhz, 8: 648 Mhz,
+  9: 652.8 Mhz
+  0: Auto (Max based on reference clock frequency), 1: 172.8 Mhz, 2: 180 Mhz, 3: 190
+  Mhz, 4: 307.2 Mhz, 5: 312 Mhz, 6: 552 Mhz, 7: 556.8 Mhz, 8: 648 Mhz, 9: 652.8 Mhz
+**/
+  UINT8                       CdClock;
+
+/** Offset 0x0419 - Enable/Disable PeiGraphicsPeimInit
+  Enable: Enable PeiGraphicsPeimInit, Disable(Default): Disable PeiGraphicsPeimInit
+  $EN_DIS
+**/
+  UINT8                       PeiGraphicsPeimInit;
+
+/** Offset 0x041A - Reserved
+**/
+  UINT8                       Reserved16[160];
+
+/** Offset 0x04BA - Skip Multi-Processor Initialization
+  When this is skipped, boot loader must initialize processors before SilicionInit
+  API. </b>0: Initialize; <b>1: Skip
+  $EN_DIS
+**/
+  UINT8                       SkipMpInit;
+
+/** Offset 0x04BB - Reserved
+**/
+  UINT8                       Reserved17[9];
+
+/** Offset 0x04C4 - CpuMpPpi
+  Pointer for CpuMpPpi
+**/
+  UINT32                      CpuMpPpi;
+
+/** Offset 0x04C8 - Reserved
+**/
+  UINT8                      Reserved18[86];
+
+/** Offset 0x051E - RTC Cmos Memory Lock
+  Enable RTC lower and upper 128 byte Lock bits to lock Bytes 38h-3Fh in the upper
+  and and lower 128-byte bank of RTC RAM.
+  $EN_DIS
+**/
+  UINT8                       RtcMemoryLock;
+
+/** Offset 0x051F - Reserved
+**/
+  UINT8                       Reserved19[24];
+
+/** Offset 0x0537 - Enable PCIE RP Pm Sci
+  Indicate whether the root port power manager SCI is enabled.
+**/
+  UINT8                       PcieRpPmSci[24];
+
+/** Offset 0x054F - Reserved
+**/
+  UINT8                       Reserved20[24];
+
+/** Offset 0x0567 - Enable PCIE RP Clk Req Detect
+  Probe CLKREQ# signal before enabling CLKREQ# based power management.
+**/
+  UINT8                       PcieRpClkReqDetect[24];
+
+/** Offset 0x057F - Reserved
+**/
+  UINT8                       Reserved21[455];
+
+/** Offset 0x0746 - PCH Pm Slp S3 Min Assert
+  SLP_S3 Minimum Assertion Width Policy. Default is PchSlpS350ms.
+**/
+  UINT8                       PchPmSlpS3MinAssert;
+
+/** Offset 0x0747 - Reserved
+**/
+  UINT8                       Reserved22;
+
+/** Offset 0x0748 - PCH Pm Slp Sus Min Assert
+  SLP_SUS Minimum Assertion Width Policy. Default is PchSlpSus4s.
+**/
+  UINT8                       PchPmSlpSusMinAssert;
+
+/** Offset 0x0749 - PCH Pm Slp A Min Assert
+  SLP_A Minimum Assertion Width Policy. Default is PchSlpA2s.
+**/
+  UINT8                       PchPmSlpAMinAssert;
+
+/** Offset 0x074A - Reserved
+**/
+  UINT8                       Reserved23[11];
+
+/** Offset 0x0755 - PCH Sata Pwr Opt Enable
+  SATA Power Optimizer on PCH side.
+  $EN_DIS
+**/
+  UINT8                       SataPwrOptEnable;
+
+/** Offset 0x0756 - Reserved
+**/
+  UINT8                       Reserved24[146];
+
+/** Offset 0x07E8 - USB2 Port Over Current Pin
+  Describe the specific over current pin number of USB 2.0 Port N.
+**/
+  UINT8                       Usb2OverCurrentPin[16];
+
+/** Offset 0x07F8 - USB3 Port Over Current Pin
+  Describe the specific over current pin number of USB 3.0 Port N.
+**/
+  UINT8                       Usb3OverCurrentPin[10];
+
+/** Offset 0x0802 - Enable 8254 Static Clock Gating
+  Set 8254CGE=1 is required for SLP_S0 support. However, set 8254CGE=1 in POST time
+  might fail to boot legacy OS using 8254 timer. Make sure it is disabled to support
+  legacy OS using 8254 timer. Also enable this while S0ix is enabled.
+  $EN_DIS
+**/
+  UINT8                       Enable8254ClockGating;
+
+/** Offset 0x0803 - Enable 8254 Static Clock Gating On S3
+  This is only applicable when Enable8254ClockGating is disabled. FSP will do the
+  8254 CGE programming on S3 resume when Enable8254ClockGatingOnS3 is enabled. This
+  avoids the SMI requirement for the programming.
+  $EN_DIS
+**/
+  UINT8                       Enable8254ClockGatingOnS3;
+
+/** Offset 0x0804 - Reserved
+**/
+  UINT8                       Reserved25[531];
+
+/** Offset 0x0A17 - Enable/Disable IGFX PmSupport
+  Enable(Default): Enable IGFX PmSupport, Disable: Disable IGFX PmSupport
+  $EN_DIS
+**/
+  UINT8                       PmSupport;
+
+/** Offset 0x0A18 - Reserved
+**/
+  UINT8                       Reserved26[32];
+
+/** Offset 0x0A38 - TCC Activation Offset
+  TCC Activation Offset. Offset from factory set TCC activation temperature at which
+  the Thermal Control Circuit must be activated. TCC will be activated at TCC Activation
+  Temperature, in volts.For SKL Y SKU, the recommended default for this policy is
+  <b>10</b>, For all other SKUs the recommended default are <b>0</b>
+**/
+  UINT8                       TccActivationOffset;
+
+/** Offset 0x0A39 - Reserved
+**/
+  UINT8                       Reserved27[34];
+
+/** Offset 0x0A5B - Enable or Disable CPU power states (C-states)
+  Enable or Disable CPU power states (C-states). 0: Disable; <b>1: Enable</b>
+  $EN_DIS
+**/
+  UINT8                       Cx;
+
+/** Offset 0x0A5C - Reserved
+**/
+  UINT8                       Reserved28[74];
+
+/** Offset 0x0AA6 - Platform Power Pmax
+  PCODE MMIO Mailbox: Platform Power Pmax. <b>0 - Auto</b> Specified in 1/8 Watt increments.
+  Range 0-1024 Watts. Value of 800 = 100W
+**/
+  UINT16                      PsysPmax;
+
+/** Offset 0x0AA8 - Reserved
+**/
+  UINT8                      Reserved29[116];
+
+/** Offset 0x0B1C - End of Post message
+  Test, Send End of Post message. Disable(0x0): Disable EOP message, Send in PEI(0x1):
+  EOP send in PEI, Send in DXE(0x2)(Default): EOP send in DXE
+  0:Disable, 1:Send in PEI, 2:Send in DXE, 3:Reserved
+**/
+  UINT8                       EndOfPostMessage;
+
+/** Offset 0x0B1D - Reserved
+**/
+  UINT8                       Reserved30[3];
+
+/** Offset 0x0B20 - Unlock all GPIO pads
+  Force all GPIO pads to be unlocked for debug purpose.
+  $EN_DIS
+**/
+  UINT8                       PchUnlockGpioPads;
+
+/** Offset 0x0B21 - Reserved
+**/
+  UINT8                       Reserved31[447];
+} FSP_S_CONFIG;
+
+/** Fsp S UPD Configuration
+**/
+typedef struct {
+
+/** Offset 0x0000
+**/
+  FSP_UPD_HEADER              FspUpdHeader;
+
+/** Offset 0x0020
+**/
+  FSP_S_CONFIG                FspsConfig;
+
+/** Offset 0x0CE0
+**/
+  UINT8                       UnusedUpdSpace37[6];
+
+/** Offset 0x0CE6
+**/
+  UINT16                      UpdTerminator;
+} FSPS_UPD;
+
+#pragma pack()
+
+#endif
diff --git a/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FsptUpd.h b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FsptUpd.h
new file mode 100644
index 0000000..508705c
--- /dev/null
+++ b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/FsptUpd.h
@@ -0,0 +1,186 @@
+/** @file
+
+Copyright (c) 2019, Intel Corporation. All rights reserved.<BR>
+
+Redistribution and use in source and binary forms, with or without modification,
+are permitted provided that the following conditions are met:
+
+* Redistributions of source code must retain the above copyright notice, this
+  list of conditions and the following disclaimer.
+* Redistributions in binary form must reproduce the above copyright notice, this
+  list of conditions and the following disclaimer in the documentation and/or
+  other materials provided with the distribution.
+* Neither the name of Intel Corporation nor the names of its contributors may
+  be used to endorse or promote products derived from this software without
+  specific prior written permission.
+
+  THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+  ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+  LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+  CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+  SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+  INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+  CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+  ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF
+  THE POSSIBILITY OF SUCH DAMAGE.
+
+  This file is automatically generated. Please do NOT modify !!!
+
+**/
+
+#ifndef __FSPTUPD_H__
+#define __FSPTUPD_H__
+
+#include <FspUpd.h>
+
+#pragma pack(1)
+
+
+/** Fsp T Core UPD
+**/
+typedef struct {
+
+/** Offset 0x0020
+**/
+  UINT32                      MicrocodeRegionBase;
+
+/** Offset 0x0024
+**/
+  UINT32                      MicrocodeRegionSize;
+
+/** Offset 0x0028
+**/
+  UINT32                      CodeRegionBase;
+
+/** Offset 0x002C
+**/
+  UINT32                      CodeRegionSize;
+
+/** Offset 0x0030
+**/
+  UINT8                       Reserved[16];
+} FSPT_CORE_UPD;
+
+/** Fsp T Configuration
+**/
+typedef struct {
+
+/** Offset 0x0040 - PcdSerialIoUartDebugEnable
+  Enable SerialIo Uart debug library with/without initializing SerialIo Uart device in FSP.
+  0:Disable, 1:Enable and Initialize, 2:Enable without Initializing
+**/
+  UINT8                       PcdSerialIoUartDebugEnable;
+
+/** Offset 0x0041 - PcdSerialIoUartNumber - FSPT
+  Select SerialIo Uart Controller for debug. Note: If UART0 is selected as CNVi BT
+  Core interface, it cannot be used for debug purpose.
+  0:SerialIoUart0, 1:SerialIoUart1, 2:SerialIoUart2
+**/
+  UINT8                       PcdSerialIoUartNumber;
+
+/** Offset 0x0042 - PcdSerialIoUartMode - FSPT
+  Select SerialIo Uart Controller mode
+  0:SerialIoUartDisabled, 1:SerialIoUartPci, 2:SerialIoUartHidden, 3:SerialIoUartCom,
+  4:SerialIoUartSkipInit
+**/
+  UINT8                       PcdSerialIoUartMode;
+
+/** Offset 0x0043
+**/
+  UINT8                       UnusedUpdSpace0;
+
+/** Offset 0x0044 - PcdSerialIoUartBaudRate - FSPT
+  Set default BaudRate Supported from 0 - default to 6000000
+**/
+  UINT32                      PcdSerialIoUartBaudRate;
+
+/** Offset 0x0048 - Pci Express Base Address
+  Base address to be programmed for Pci Express
+**/
+  UINT64                      PcdPciExpressBaseAddress;
+
+/** Offset 0x0050 - Pci Express Region Length
+  Region Length to be programmed for Pci Express
+**/
+  UINT32                      PcdPciExpressRegionLength;
+
+/** Offset 0x0054 - PcdSerialIoUartParity - FSPT
+  Set default Parity.
+  0: DefaultParity, 1: NoParity, 2: EvenParity, 3: OddParity
+**/
+  UINT8                       PcdSerialIoUartParity;
+
+/** Offset 0x0055 - PcdSerialIoUartDataBits - FSPT
+  Set default word length. 0: Default, 5,6,7,8
+**/
+  UINT8                       PcdSerialIoUartDataBits;
+
+/** Offset 0x0056 - PcdSerialIoUartStopBits - FSPT
+  Set default stop bits.
+  0: DefaultStopBits, 1: OneStopBit, 2: OneFiveStopBits, 3: TwoStopBits
+**/
+  UINT8                       PcdSerialIoUartStopBits;
+
+/** Offset 0x0057 - PcdSerialIoUartAutoFlow - FSPT
+  Enables UART hardware flow control, CTS and RTS lines.
+  0: Disable, 1:Enable
+**/
+  UINT8                       PcdSerialIoUartAutoFlow;
+
+/** Offset 0x0058 - PcdSerialIoUartRxPinMux - FSPT
+  Select RX pin muxing for SerialIo UART used for debug
+**/
+  UINT32                      PcdSerialIoUartRxPinMux;
+
+/** Offset 0x005C - PcdSerialIoUartTxPinMux - FSPT
+  Select TX pin muxing for SerialIo UART used for debug
+**/
+  UINT32                      PcdSerialIoUartTxPinMux;
+
+/** Offset 0x0060 - PcdSerialIoUartRtsPinMux - FSPT
+  Select SerialIo Uart used for debug Rts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_RTS*
+  for possible values.
+**/
+  UINT32                      PcdSerialIoUartRtsPinMux;
+
+/** Offset 0x0064 - PcdSerialIoUartCtsPinMux - FSPT
+  Select SerialIo Uart used for debug Cts pin muxing. Refer to GPIO_*_MUXING_SERIALIO_UARTx_CTS*
+  for possible values.
+**/
+  UINT32                      PcdSerialIoUartCtsPinMux;
+
+/** Offset 0x0068
+**/
+  UINT8                       ReservedFsptUpd1[24];
+} FSP_T_CONFIG;
+
+/** Fsp T UPD Configuration
+**/
+typedef struct {
+
+/** Offset 0x0000
+**/
+  FSP_UPD_HEADER              FspUpdHeader;
+
+/** Offset 0x0020
+**/
+  FSPT_CORE_UPD               FsptCoreUpd;
+
+/** Offset 0x0040
+**/
+  FSP_T_CONFIG                FsptConfig;
+
+/** Offset 0x0080
+**/
+  UINT8                       UnusedUpdSpace1[6];
+
+/** Offset 0x0086
+**/
+  UINT16                      UpdTerminator;
+} FSPT_UPD;
+
+#pragma pack()
+
+#endif
diff --git a/src/vendorcode/intel/fsp/fsp2_0/jasperlake/MemInfoHob.h b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/MemInfoHob.h
new file mode 100644
index 0000000..f1ca44f
--- /dev/null
+++ b/src/vendorcode/intel/fsp/fsp2_0/jasperlake/MemInfoHob.h
@@ -0,0 +1,274 @@
+/** @file
+  This file contains definitions required for creation of
+  Memory S3 Save data, Memory Info data and Memory Platform
+  data hobs.
+
+  @copyright
+  Copyright (c) 1999 - 2019, Intel Corporation. All rights reserved.<BR>
+  This program and the accompanying materials are licensed and made available under
+  the terms and conditions of the BSD License that accompanies this distribution.
+  The full text of the license may be found at
+  http://opensource.org/licenses/bsd-license.php.
+  THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS,
+
+  WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED.
+
+@par Specification Reference:
+**/
+#ifndef _MEM_INFO_HOB_H_
+#define _MEM_INFO_HOB_H_
+
+#include <Uefi/UefiMultiPhase.h>
+#include <Pi/PiBootMode.h>
+#include <Pi/PiHob.h>
+
+#pragma pack (push, 1)
+
+extern EFI_GUID gSiMemoryS3DataGuid;
+extern EFI_GUID gSiMemoryInfoDataGuid;
+extern EFI_GUID gSiMemoryPlatformDataGuid;
+
+#define MAX_NODE        1
+#define MAX_CH          2
+#define MAX_DIMM        2
+
+///
+/// Host reset states from MRC.
+///
+#define  WARM_BOOT        2
+
+#define R_MC_CHNL_RANK_PRESENT  0x7C
+#define   B_RANK0_PRS           BIT0
+#define   B_RANK1_PRS           BIT1
+#define   B_RANK2_PRS           BIT4
+#define   B_RANK3_PRS           BIT5
+
+///
+/// Defines taken from MRC so avoid having to include MrcInterface.h
+///
+
+//
+// Matches MAX_SPD_SAVE define in MRC
+//
+#ifndef MAX_SPD_SAVE
+#define MAX_SPD_SAVE 29
+#endif
+
+//
+// MRC version description.
+//
+typedef struct {
+  UINT8  Major;     ///< Major version number
+  UINT8  Minor;     ///< Minor version number
+  UINT8  Rev;       ///< Revision number
+  UINT8  Build;     ///< Build number
+} SiMrcVersion;
+
+//
+// Matches MrcChannelSts enum in MRC
+//
+#ifndef CHANNEL_NOT_PRESENT
+#define CHANNEL_NOT_PRESENT     0  // There is no channel present on the controller.
+#endif
+#ifndef CHANNEL_DISABLED
+#define CHANNEL_DISABLED     1  // There is a channel present but it is disabled.
+#endif
+#ifndef CHANNEL_PRESENT
+#define CHANNEL_PRESENT     2  // There is a channel present and it is enabled.
+#endif
+
+//
+// Matches MrcDimmSts enum in MRC
+//
+#ifndef DIMM_ENABLED
+#define DIMM_ENABLED     0  // DIMM/rank Pair is enabled, presence will be detected.
+#endif
+#ifndef DIMM_DISABLED
+#define DIMM_DISABLED    1  // DIMM/rank Pair is disabled, regardless of presence.
+#endif
+#ifndef DIMM_PRESENT
+#define DIMM_PRESENT     2  // There is a DIMM present in the slot/rank pair and it will be used.
+#endif
+#ifndef DIMM_NOT_PRESENT
+#define DIMM_NOT_PRESENT 3  // There is no DIMM present in the slot/rank pair.
+#endif
+
+//
+// Matches MrcBootMode enum in MRC
+//
+#ifndef bmCold
+#define bmCold 0            // Cold boot
+#endif
+#ifndef bmWarm
+#define bmWarm 1            // Warm boot
+#endif
+#ifndef bmS3
+#define bmS3   2            // S3 resume
+#endif
+#ifndef bmFast
+#define bmFast 3            // Fast boot
+#endif
+
+//
+// Matches MrcDdrType enum in MRC
+//
+#ifndef MRC_DDR_TYPE_DDR4
+#define MRC_DDR_TYPE_DDR4     0
+#endif
+#ifndef MRC_DDR_TYPE_DDR3
+#define MRC_DDR_TYPE_DDR3     1
+#endif
+#ifndef MRC_DDR_TYPE_LPDDR3
+#define MRC_DDR_TYPE_LPDDR3   2
+#endif
+#ifndef CPU_CFL//CNL
+#ifndef MRC_DDR_TYPE_LPDDR4
+#define MRC_DDR_TYPE_LPDDR4   3
+#endif
+#else//CFL
+#ifndef MRC_DDR_TYPE_UNKNOWN
+#define MRC_DDR_TYPE_UNKNOWN  3
+#endif
+#endif//CPU_CFL-endif
+
+#define MAX_PROFILE_NUM     4 // number of memory profiles supported
+#define MAX_XMP_PROFILE_NUM 2 // number of XMP profiles supported
+
+//
+// DIMM timings
+//
+typedef struct {
+  UINT32 tCK;       ///< Memory cycle time, in femtoseconds.
+  UINT16 NMode;     ///< Number of tCK cycles for the channel DIMM's command rate mode.
+  UINT16 tCL;       ///< Number of tCK cycles for the channel DIMM's CAS latency.
+  UINT16 tCWL;      ///< Number of tCK cycles for the channel DIMM's minimum CAS write latency time.
+  UINT16 tFAW;      ///< Number of tCK cycles for the channel DIMM's minimum four activate window delay time.
+  UINT16 tRAS;      ///< Number of tCK cycles for the channel DIMM's minimum active to precharge delay time.
+  UINT16 tRCDtRP;   ///< Number of tCK cycles for the channel DIMM's minimum RAS# to CAS# delay time and Row Precharge delay time.
+  UINT16 tREFI;     ///< Number of tCK cycles for the channel DIMM's minimum Average Periodic Refresh Interval.
+  UINT16 tRFC;      ///< Number of tCK cycles for the channel DIMM's minimum refresh recovery delay time.
+  UINT16 tRFCpb;    ///< Number of tCK cycles for the channel DIMM's minimum per bank refresh recovery delay time.
+  UINT16 tRFC2;     ///< Number of tCK cycles for the channel DIMM's minimum refresh recovery delay time.
+  UINT16 tRFC4;     ///< Number of tCK cycles for the channel DIMM's minimum refresh recovery delay time.
+  UINT16 tRPab;     ///< Number of tCK cycles for the channel DIMM's minimum row precharge delay time for all banks.
+  UINT16 tRRD;      ///< Number of tCK cycles for the channel DIMM's minimum row active to row active delay time.
+  UINT16 tRRD_L;    ///< Number of tCK cycles for the channel DIMM's minimum row active to row active delay time for same bank groups.
+  UINT16 tRRD_S;    ///< Number of tCK cycles for the channel DIMM's minimum row active to row active delay time for different bank groups.
+  UINT16 tRTP;      ///< Number of tCK cycles for the channel DIMM's minimum internal read to precharge command delay time.
+  UINT16 tWR;       ///< Number of tCK cycles for the channel DIMM's minimum write recovery time.
+  UINT16 tWTR;      ///< Number of tCK cycles for the channel DIMM's minimum internal write to read command delay time.
+  UINT16 tWTR_L;    ///< Number of tCK cycles for the channel DIMM's minimum internal write to read command delay time for same bank groups.
+  UINT16 tWTR_S;    ///< Number of tCK cycles for the channel DIMM's minimum internal write to read command delay time for different bank groups.
+  UINT16 tCCD_L;  ///< Number of tCK cycles for the channel DIMM's minimum CAS-to-CAS delay for same bank group.
+} MRC_CH_TIMING;
+
+typedef struct {
+  UINT8 SG;         ///< Number of tCK cycles between transactions in the same bank group.
+  UINT8 DG;         ///< Number of tCK cycles between transactions when switching bank groups.
+  UINT8 DR;         ///< Number of tCK cycles between transactions when switching between Ranks (in the same DIMM).
+  UINT8 DD;         ///< Number of tCK cycles between transactions when switching between DIMMs.
+} MRC_TA_TIMING;
+
+///
+/// Memory SMBIOS & OC Memory Data Hob
+///
+typedef struct {
+  UINT8            Status;                  ///< See MrcDimmStatus for the definition of this field.
+  UINT8            DimmId;
+  UINT32           DimmCapacity;            ///< DIMM size in MBytes.
+  UINT16           MfgId;
+  UINT8            ModulePartNum[20];       ///< Module part number for DDR3 is 18 bytes however for DRR4 20 bytes as per JEDEC Spec, so reserving 20 bytes
+  UINT8            RankInDimm;              ///< The number of ranks in this DIMM.
+  UINT8            SpdDramDeviceType;       ///< Save SPD DramDeviceType information needed for SMBIOS structure creation.
+  UINT8            SpdModuleType;           ///< Save SPD ModuleType information needed for SMBIOS structure creation.
+  UINT8            SpdModuleMemoryBusWidth; ///< Save SPD ModuleMemoryBusWidth information needed for SMBIOS structure creation.
+  UINT8            SpdSave[MAX_SPD_SAVE];   ///< Save SPD Manufacturing information needed for SMBIOS structure creation.
+  UINT16           Speed;                   ///< The maximum capable speed of the device, in MHz.
+} DIMM_INFO;
+
+typedef struct {
+  UINT8            Status;                  ///< Indicates whether this channel should be used.
+  UINT8            ChannelId;
+  UINT8            DimmCount;               ///< Number of valid DIMMs that exist in the channel.
+  MRC_CH_TIMING    Timing[MAX_PROFILE_NUM]; ///< The channel timing values.
+  DIMM_INFO        DimmInfo[MAX_DIMM];      ///< Save the DIMM output characteristics.
+  MRC_TA_TIMING    tRd2Rd;                  ///< Read-to-Read   Turn Around Timings
+  MRC_TA_TIMING    tRd2Wr;                  ///< Read-to-Write  Turn Around Timings
+  MRC_TA_TIMING    tWr2Rd;                  ///< Write-to-Read  Turn Around Timings
+  MRC_TA_TIMING    tWr2Wr;                  ///< Write-to-Write Turn Around Timings
+} CHANNEL_INFO;
+
+typedef struct {
+  UINT8             Status;                  ///< Indicates whether this controller should be used.
+  UINT16            DeviceId;                ///< The PCI device id of this memory controller.
+  UINT8             RevisionId;              ///< The PCI revision id of this memory controller.
+  UINT8             ChannelCount;            ///< Number of valid channels that exist on the controller.
+  CHANNEL_INFO      ChannelInfo[MAX_CH];     ///< The following are channel level definitions.
+  MRC_TA_TIMING    tRd2Rd;                   ///< Deprecated and moved to CHANNEL_INFO. Read-to-Read   Turn Around Timings
+  MRC_TA_TIMING    tRd2Wr;                   ///< Deprecated and moved to CHANNEL_INFO. Read-to-Write  Turn Around Timings
+  MRC_TA_TIMING    tWr2Rd;                   ///< Deprecated and moved to CHANNEL_INFO. Write-to-Read  Turn Around Timings
+  MRC_TA_TIMING    tWr2Wr;                   ///< Deprecated and moved to CHANNEL_INFO. Write-to-Write Turn Around Timings
+} CONTROLLER_INFO;
+
+typedef struct {
+  UINT8             Revision;
+  UINT16            DataWidth;              ///< Data width, in bits, of this memory device
+  /** As defined in SMBIOS 3.0 spec
+    Section 7.18.2 and Table 75
+  **/
+  UINT8             MemoryType;             ///< DDR type: DDR3, DDR4, or LPDDR3
+  UINT16            MaximumMemoryClockSpeed;///< The maximum capable speed of the device, in megahertz (MHz)
+  UINT16            ConfiguredMemoryClockSpeed; ///< The configured clock speed to the memory device, in megahertz (MHz)
+  /** As defined in SMBIOS 3.0 spec
+    Section 7.17.3 and Table 72
+  **/
+  UINT8             ErrorCorrectionType;
+
+  SiMrcVersion      Version;
+  BOOLEAN           EccSupport;
+  UINT8             MemoryProfile;
+  UINT32            TotalPhysicalMemorySize;
+  UINT32            DefaultXmptCK[MAX_XMP_PROFILE_NUM];///< Stores the tCK value read from SPD XMP profiles if they exist.
+  UINT8             XmpProfileEnable;                  ///< If XMP capable DIMMs are detected, this will indicate which XMP Profiles are common among all DIMMs.
+  UINT8             Ratio;
+  UINT8             RefClk;
+  UINT32            VddVoltage[MAX_PROFILE_NUM];
+  CONTROLLER_INFO   Controller[MAX_NODE];
+} MEMORY_INFO_DATA_HOB;
+
+/**
+  Memory Platform Data Hob
+
+  <b>Revision 1:</b>
+  - Initial version.
+  <b>Revision 2:</b>
+  - Added TsegBase, PrmrrSize, PrmrrBase, Gttbase, MmioSize, PciEBaseAddress fields
+**/
+typedef struct {
+  UINT8             Revision;
+  UINT8             Reserved[3];
+  UINT32            BootMode;
+  UINT32            TsegSize;
+  UINT32            TsegBase;
+  UINT32            PrmrrSize;
+  UINT32            PrmrrBase;
+  UINT32            GttBase;
+  UINT32            MmioSize;
+  UINT32            PciEBaseAddress;
+#ifdef CPU_CFL
+  UINT32            GdxcIotBase;
+  UINT32            GdxcIotSize;
+  UINT32            GdxcMotBase;
+  UINT32            GdxcMotSize;
+#endif //CPU_CFL
+} MEMORY_PLATFORM_DATA;
+
+typedef struct {
+  EFI_HOB_GUID_TYPE    EfiHobGuidType;
+  MEMORY_PLATFORM_DATA Data;
+  UINT8                *Buffer;
+} MEMORY_PLATFORM_DATA_HOB;
+
+#pragma pack (pop)
+
+#endif // _MEM_INFO_HOB_H_
-- 
To view, visit https://review.coreboot.org/c/coreboot/+/37559
To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings

Gerrit-Project: coreboot
Gerrit-Branch: master
Gerrit-Change-Id: Iacb44204c3f7220a20ab3edc2163c97188014bbf
Gerrit-Change-Number: 37559
Gerrit-PatchSet: 1
Gerrit-Owner: Aamir Bohra aamir.bohra@intel.com
Gerrit-Reviewer: Aamir Bohra aamir.bohra@intel.com
Gerrit-Reviewer: Patrick Rudolph siro@das-labor.org
Gerrit-MessageType: newchange



    

Change in coreboot[master]: vendorcode/intel/fsp: Add Jasperlake FSP headers for FSP v1433