Furquan Shaikh has uploaded this change for review. ( https://review.coreboot.org/26971
Change subject: mb/google/octopus: Fix GPIO to GPE mappings in devicetree ......................................................................
mb/google/octopus: Fix GPIO to GPE mappings in devicetree
Change b41ae2 (mb/google/octopus: Enable wake-over-wifi for octopus variants) changed the GPE mappings to accomodate for WiFi wake pin. However, this resulted in TPM interrupt pin being removed from the GPIO to GPE mapping. Since we do not support true interrupts in coreboot, GPE_STS registers are used to identify if an interrupt has triggered. Change in GPE mapping resulted in this information to be lost when talking to TPM thus resulting in "Timeout wait for tpm irq".
This change fixes the above issue by assigning GPIO block for TPM interrupt back to DW1 and moving GPIO block for wake-over-wifi pin to DW3. DW3 was mapping to NW_31_0 which only has debug header pins and CNVI pins (none of them are used for reading GPE_STS or as wake sources).
BUG=b:109824918 TEST=Verified that there are no "Timeout wait for tpm irq" messages when talking to TPM.
Change-Id: I30768177a838a684948f7485d760c8b83c3190f7 Signed-off-by: Furquan Shaikh furquan@google.com --- M src/mainboard/google/octopus/variants/baseboard/devicetree.cb M src/mainboard/google/octopus/variants/bip/devicetree.cb 2 files changed, 23 insertions(+), 6 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/71/26971/1
diff --git a/src/mainboard/google/octopus/variants/baseboard/devicetree.cb b/src/mainboard/google/octopus/variants/baseboard/devicetree.cb index 9bd51ca..d6f0829 100644 --- a/src/mainboard/google/octopus/variants/baseboard/devicetree.cb +++ b/src/mainboard/google/octopus/variants/baseboard/devicetree.cb @@ -29,9 +29,18 @@ # route, i.e., if this route changes then the affected GPE # offset bits also need to be changed. This sets the PMC register # GPE_CFG fields. - register "gpe0_dw1" = "PMC_GPE_N_63_32" + # DW1 is used by: + # - GPIO_63 - H1_PCH_INT_ODL + # DW2 is used by: + # - GPIO_141 - EC_PCH_WAKE_ODL + # - GPIO_142 - TRACKPAD_INT2_1V8_ODL + # - GPIO_144 - PEN_EJECT_ODL + # DW3 is used by: + # - GPIO_117 - LTE_WAKE_ODL + # - GPIO_119 - WLAN_PCIE_WAKE_ODL + register "gpe0_dw1" = "PMC_GPE_NW_63_32" register "gpe0_dw2" = "PMC_GPE_N_95_64" - register "gpe0_dw3" = "PMC_GPE_NW_31_0" + register "gpe0_dw3" = "PMC_GPE_N_63_32"
# PL1 override 8000 mW: Due to error in the energy calculation for # current VR solution. Experiments show that SoC TDP max (6W) can @@ -122,7 +131,7 @@ device pci 12.0 off end # - SATA device pci 13.0 on chip drivers/intel/wifi - register "wake" = "GPE0_DW1_11" + register "wake" = "GPE0_DW3_11" device pci 00.0 on end end end # - PCIe-A 0 Onboard M2 Slot(Wifi) diff --git a/src/mainboard/google/octopus/variants/bip/devicetree.cb b/src/mainboard/google/octopus/variants/bip/devicetree.cb index 339b5bf..8f2992b 100644 --- a/src/mainboard/google/octopus/variants/bip/devicetree.cb +++ b/src/mainboard/google/octopus/variants/bip/devicetree.cb @@ -29,9 +29,17 @@ # route, i.e., if this route changes then the affected GPE # offset bits also need to be changed. This sets the PMC register # GPE_CFG fields. - register "gpe0_dw1" = "PMC_GPE_N_63_32" + # DW1 is used by: + # - GPIO_63 - H1_PCH_INT_ODL + # DW2 is used by: + # - GPIO_141 - EC_PCH_WAKE_ODL + # - GPIO_142 - TRACKPAD_INT2_1V8_ODL + # DW3 is used by: + # - GPIO_117 - LTE_WAKE_ODL + # - GPIO_119 - WLAN_PCIE_WAKE_ODL + register "gpe0_dw1" = "PMC_GPE_NW_63_32" register "gpe0_dw2" = "PMC_GPE_N_95_64" - register "gpe0_dw3" = "PMC_GPE_NW_31_0" + register "gpe0_dw3" = "PMC_GPE_N_63_32"
# PL1 override 8000 mW: Due to error in the energy calculation for # current VR solution. Experiments show that SoC TDP max (6W) can @@ -122,7 +130,7 @@ device pci 12.0 off end # - SATA device pci 13.0 on chip drivers/intel/wifi - register "wake" = "GPE0_DW1_11" + register "wake" = "GPE0_DW3_11" device pci 00.0 on end end end # - PCIe-A 0 Onboard M2 Slot(Wifi)