[L] Change in coreboot[main]: mb/google/var/riven: Optimize the stop delay for touchsreen
Kapil Porwal has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/85039?usp=email )
Change subject: mb/google/var/riven: Optimize the stop delay for touchsreen ......................................................................
mb/google/var/riven: Optimize the stop delay for touchsreen
Reduce stop delay for touchscreen based on the latest spec. This will optimize the touch response time to keep the S0ix resume time under 500ms.
BUG=b:378012214 TEST=Verify improvement in resume time on Riven.
Change-Id: Id7dcbc393bfae9bb62b5700bb9042a543152e968 Signed-off-by: Kapil Porwal kapilporwal@google.com --- M src/mainboard/google/brya/variants/riven/overridetree.cb A src/mainboard/google/brya/variants/riven/overridetree.cb.orig 2 files changed, 666 insertions(+), 2 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/39/85039/1
diff --git a/src/mainboard/google/brya/variants/riven/overridetree.cb b/src/mainboard/google/brya/variants/riven/overridetree.cb index 00947c4..9f62d27 100644 --- a/src/mainboard/google/brya/variants/riven/overridetree.cb +++ b/src/mainboard/google/brya/variants/riven/overridetree.cb @@ -243,7 +243,7 @@ register "generic.reset_delay_ms" = "20" register "generic.reset_off_delay_ms" = "2" register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" - register "generic.stop_delay_ms" = "280" + register "generic.stop_delay_ms" = "180" register "generic.stop_off_delay_ms" = "2" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "1" @@ -260,7 +260,7 @@ register "generic.reset_delay_ms" = "20" register "generic.reset_off_delay_ms" = "2" register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" - register "generic.stop_delay_ms" = "280" + register "generic.stop_delay_ms" = "180" register "generic.stop_off_delay_ms" = "2" register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" register "generic.enable_delay_ms" = "1" diff --git a/src/mainboard/google/brya/variants/riven/overridetree.cb.orig b/src/mainboard/google/brya/variants/riven/overridetree.cb.orig new file mode 100644 index 0000000..00947c4 --- /dev/null +++ b/src/mainboard/google/brya/variants/riven/overridetree.cb.orig @@ -0,0 +1,664 @@ +fw_config + field DB_USB 0 1 + option DB_NONE 0 + option DB_1C_1A 1 + option DB_1C_LTE 2 + end + field STYLUS 2 + option STYLUS_ABSENT 0 + option STYLUS_PRESENT 1 + end + field WIFI_SAR_ID 4 6 + option ID_0 0 + option ID_1 1 + end + field WIFI_TYPE 7 + option WIFI_CNVI 0 + option WIFI_PCIE 1 + end + field WFC 9 10 + option WFC_ABSENT 0 + option WFC_MIPI_OVTI5675 1 + option WFC_MIPI_OVTI8856 2 + end +end + +chip soc/intel/alderlake + # Acoustic settings + register "acoustic_noise_mitigation" = "1" + register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_4" + register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_4" + register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1" + register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1" + + register "sagv" = "SaGv_Enabled" + + # EMMC Tx CMD Delay + # Refer to EDS-Vol2-42.3.7. + # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-42.3.8. + # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. + # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-42.3.9. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. + # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-42.3.10. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. + # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F3C" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-42.3.12. + # [17:16] stands for Rx Clock before Output Buffer, + # 00: Rx clock after output buffer, + # 01: Rx clock before output buffer, + # 10: Automatic selection based on working mode. + # 11: Reserved + # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10023" + + # EMMC Rx Strobe Delay + # Refer to EDS-Vol2-42.3.11. + # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. + # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515" + + # SOC Aux orientation override: + # This is a bitfield that corresponds to up to 4 TCSS ports. + # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. + # TcssAuxOri = 0101b + # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports + # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the + # motherboard to USBC connector + register "tcss_aux_ori" = "5" + + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" + + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN + register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN + + # Enable the Cnvi BT Audio Offload + register "cnvi_bt_audio_offload" = "1" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| I2C0 | TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C1 | Touchscreen | + #| I2C2 | Sub-board(PSensor)/WCAM | + #| I2C3 | Audio | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .early_init = 1, + .speed = I2C_SPEED_FAST_PLUS, + .speed_config[0] = { + .speed = I2C_SPEED_FAST_PLUS, + .scl_lcnt = 55, + .scl_hcnt = 30, + .sda_hold = 7, + } + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 30, + } + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 40, + } + }, + }" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""Memory"" + register "options.tsr[1].desc" = ""Charger"" + register "options.tsr[2].desc" = ""Ambient"" + + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 5500, + .max_power = 6000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 28 * MSECS_PER_SEC, + .granularity = 200 + }, + .pl2 = { + .min_power = 25000, + .max_power = 25000, + .time_window_min = 1, + .time_window_max = 1, + .granularity = 1000 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + device generic 0 on end + end + end + device ref ipu on + chip drivers/intel/mipi_camera + register "acpi_uid" = "0x50000" + register "acpi_name" = ""IPU0"" + register "device_type" = "INTEL_ACPI_CAMERA_CIO2" + + register "cio2_num_ports" = "1" + register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used + register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" + register "cio2_prt[0]" = "1" + device generic 0 on end + end + probe WFC WFC_MIPI_OVTI5675 + probe WFC WFC_MIPI_OVTI8856 + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "enable_cnvi_ddr_rfim" = "true" + device generic 0 on + probe WIFI_TYPE WIFI_CNVI + end + end + end + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9004"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "280" + register "generic.stop_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9004"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "280" + register "generic.stop_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 16 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""GTCH7503"" + register "generic.desc" = ""G2 Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 40 on end + end + chip drivers/generic/gpio_keys + register "name" = ""PENH"" + register "gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_F13)" + register "key.wake_gpe" = "GPE0_DW2_15" + register "key.wakeup_route" = "WAKEUP_ROUTE_SCI" + register "key.wakeup_event_action" = "EV_ACT_DEASSERTED" + register "key.dev_name" = ""EJCT"" + register "key.linux_code" = "SW_PEN_INSERTED" + register "key.linux_input_type" = "EV_SW" + register "key.label" = ""pen_eject"" + device generic 0 on + probe STYLUS STYLUS_PRESENT + end + end + end + device ref i2c2 on + chip drivers/intel/mipi_camera + register "acpi_hid" = ""OVTI5675"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM0"" + register "chip_name" = ""Ov 5675 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + + register "ssdb.lanes_used" = "2" + register "ssdb.link_used" = "1" + register "ssdb.vcm_type" = "0x0C" + register "vcm_name" = ""VCM0"" + register "num_freq_entries" = "1" + register "link_freq[0]" = "DEFAULT_LINK_FREQ" + register "remote_name" = ""IPU0"" + + register "has_power_resource" = "1" + register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" + + #Controls + register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" + register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" + + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X + register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X + register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L + + #_ON + register "on_seq.ops_cnt" = "5" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" + register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" + + #_OFF + register "off_seq.ops_cnt" = "4" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 36 on + probe WFC WFC_MIPI_OVTI5675 + end + end + chip drivers/intel/mipi_camera + register "acpi_hid" = ""OVTI8856"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM0"" + register "chip_name" = ""Ov 8856 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + register "has_power_resource" = "1" + register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" + + register "ssdb.lanes_used" = "2" + register "ssdb.link_used" = "1" + register "ssdb.vcm_type" = "0x0C" + register "vcm_name" = ""VCM0"" + register "num_freq_entries" = "2" + register "link_freq[0]" = "720000000" + register "link_freq[1]" = "360000000" + register "remote_name" = ""IPU0"" + + #Controls + register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" + register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" + + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X + register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" # EN_PP1800_PP1200_WCAM_X + register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" # WCAM_RST_L + + #_ON + register "on_seq.ops_cnt" = "5" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" + register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" + + #_OFF + register "off_seq.ops_cnt" = "4" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 10 on + probe WFC WFC_MIPI_OVTI8856 + end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "3" + register "acpi_name" = ""VCM0"" + register "chip_name" = ""DW AF DAC"" + register "device_type" = "INTEL_ACPI_CAMERA_VCM" + + register "vcm_compat" = ""dongwoon,dw9714"" + register "has_power_resource" = "1" + register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" + + #Controls + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" # EN_PP2800_WCAM_X + + #_ON + register "on_seq.ops_cnt" = "1" + register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + + #_OFF + register "off_seq.ops_cnt" = "1" + register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 0C on + probe WFC WFC_MIPI_OVTI5675 + probe WFC WFC_MIPI_OVTI8856 + end + end + chip drivers/intel/mipi_camera + register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" + register "acpi_uid" = "1" + register "acpi_name" = ""NVM0"" + register "chip_name" = ""GT24C08"" + register "device_type" = "INTEL_ACPI_CAMERA_NVM" + + register "nvm_size" = "0x2000" + register "nvm_pagesize" = "1" + register "nvm_readonly" = "1" + register "nvm_width" = "0x10" + register "nvm_compat" = ""atmel,24c08"" + + device i2c 50 on + probe WFC WFC_MIPI_OVTI5675 + probe WFC WFC_MIPI_OVTI8856 + end + end + end + device ref i2c3 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + chip drivers/generic/alc1015 + register "hid" = ""RTL1019"" + register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + device generic 0 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "detect" = "1" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""SYNA0000"" + register "generic.cid" = ""ACPI0C50"" + register "generic.desc" = ""Synaptics Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.detect" = "1" + register "hid_desc_reg_offset" = "0x20" + device i2c 0x2c on end + end + end + device ref hda on + chip drivers/sof + register "spkr_tplg" = "rt1019" + register "jack_tplg" = "rt5682" + register "mic_tplg" = "_2ch_pdm0" + device generic 0 on end + end + end + device ref pcie_rp4 on + probe WIFI_TYPE WIFI_PCIE + # Enable wlan PCIe 4 using clk 2 + register "pch_pcie_rp[PCH_RP(4)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + chip drivers/wifi/generic + register "wake" = "GPE0_DW1_03" + register "add_acpi_dma_property" = "true" + use usb2_port8 as bluetooth_companion + device pci 00.0 on + probe WIFI_TYPE WIFI_PCIE + end + end + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)" + register "srcclk_pin" = "2" + device generic 0 on + probe WIFI_TYPE WIFI_PCIE + end + end + end + device ref pcie_rp7 off end # PCIE7 no SD card + device ref emmc on + probe STORAGE STORAGE_UNKNOWN + probe STORAGE STORAGE_EMMC + end + device ref ish on + chip drivers/intel/ish + register "add_acpi_dma_property" = "true" + device generic 0 on end + end + probe STORAGE STORAGE_UNKNOWN + probe STORAGE STORAGE_UFS + end + device ref ufs on + probe STORAGE STORAGE_UNKNOWN + probe STORAGE STORAGE_UFS + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port2 as usb2_port + use tcss_usb3_port2 as usb3_port + device generic 1 alias conn1 on + probe DB_USB DB_1C_1A + probe DB_USB DB_1C_LTE + end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port2 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port2 on + probe DB_USB DB_1C_1A + probe DB_USB DB_1C_LTE + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb2_port4 on + probe DB_USB DB_1C_1A + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port4 on + probe DB_USB DB_1C_LTE + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port8 on + probe WIFI_TYPE WIFI_PCIE + end + end + chip drivers/usb/acpi + register "desc" = ""CNVI Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on + probe WIFI_TYPE WIFI_CNVI + end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb3_port2 on + probe DB_USB DB_1C_1A + end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port2 on + probe DB_USB DB_1C_LTE + end + end + end + end + end + end +end
-
Kapil Porwal (Code Review)