[L] Change in coreboot[main]: mb/google/nissa/var/dirks: Add initial override devicetree
Ivy Jian has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/85991?usp=email )
Change subject: mb/google/nissa/var/dirks: Add initial override devicetree ......................................................................
mb/google/nissa/var/dirks: Add initial override devicetree
Add initial override devicetree for riven based on the latest schematic (0W4_TWL_A_MB_0113.pdf).
- Add eMMC DLL tuning value (copy from riven) - Configure I2C buses - Configure USB ports - Configure audio codec - Configure WIFI6(CNVi) and WIFI7(PCIe)
USB Ports for dirks: (FRONT) USBA 10G x 3 (REAR) USBA 10G x 2 + USBC 10G x 1 Note : repurpose the TCSS port 1 to USB3.2 Gen2x1 Type-A
BUG=b:388117663 TEST=none.
Change-Id: Ib227995cde8d871ff58c89ccb09221226640a7e6 Signed-off-by: Ivy Jian ivy.jian@quanta.corp-partner.google.com --- M src/mainboard/google/brya/variants/dirks/Makefile.mk M src/mainboard/google/brya/variants/dirks/overridetree.cb 2 files changed, 346 insertions(+), 2 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/91/85991/1
diff --git a/src/mainboard/google/brya/variants/dirks/Makefile.mk b/src/mainboard/google/brya/variants/dirks/Makefile.mk index d38141c..bc39984 100644 --- a/src/mainboard/google/brya/variants/dirks/Makefile.mk +++ b/src/mainboard/google/brya/variants/dirks/Makefile.mk @@ -4,3 +4,4 @@ romstage-y += gpio.c
ramstage-y += gpio.c +ramstage-y += ramstage.c diff --git a/src/mainboard/google/brya/variants/dirks/overridetree.cb b/src/mainboard/google/brya/variants/dirks/overridetree.cb index 4f2c04a..2295418 100644 --- a/src/mainboard/google/brya/variants/dirks/overridetree.cb +++ b/src/mainboard/google/brya/variants/dirks/overridetree.cb @@ -1,6 +1,349 @@ chip soc/intel/alderlake
- device domain 0 on - end + register "sagv" = "SaGv_Enabled"
+ # EMMC Tx CMD Delay + # Refer to EDS-Vol2-42.3.7. + # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-42.3.8. + # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. + # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-42.3.9. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. + # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-42.3.10. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. + # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F3C" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-42.3.12. + # [17:16] stands for Rx Clock before Output Buffer, + # 00: Rx clock after output buffer, + # 01: Rx clock before output buffer, + # 10: Automatic selection based on working mode. + # 11: Reserved + # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10023" + + # EMMC Rx Strobe Delay + # Refer to EDS-Vol2-42.3.11. + # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. + # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515" + + # SOC Aux orientation override: + # This is a bitfield that corresponds to up to 4 TCSS ports. + # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. + # TcssAuxOri = 0101b + # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports + # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the + # motherboard to USBC connector + register "tcss_aux_ori" = "0x1" + + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C0 + register "usb2_ports[1]" = "USB2_PORT_MID(OC0)" # USB2_A0 + register "usb2_ports[2]" = "USB2_PORT_MID(OC1)" # USB2_A1 + register "usb2_ports[3]" = "USB2_PORT_MID(OC2)" # USB2_A2 + register "usb2_ports[4]" = "USB2_PORT_MID(OC3)" # USB2_A3 + register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # USB2_A4 + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN + register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A1 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A2 + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A3 + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A4 + + register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC_SKIP)" # USB3_C0 + register "tcss_ports[1]" = "TCSS_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A0 + + register "serial_io_i2c_mode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoPci, + [PchSerialIoIndexI2C1] = PchSerialIoDisabled, + [PchSerialIoIndexI2C2] = PchSerialIoDisabled, + [PchSerialIoIndexI2C3] = PchSerialIoPci, + [PchSerialIoIndexI2C4] = PchSerialIoDisabled, + [PchSerialIoIndexI2C5] = PchSerialIoDisabled, + }" + + # Enable the Cnvi BT Audio Offload + register "cnvi_bt_audio_offload" = "1" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| I2C0 | TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C3 | Audio | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .early_init = 1, + .speed = I2C_SPEED_FAST_PLUS, + .speed_config[0] = { + .speed = I2C_SPEED_FAST_PLUS, + .scl_lcnt = 55, + .scl_hcnt = 30, + .sda_hold = 7, + } + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + }" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""Memory"" + register "options.tsr[1].desc" = ""Charger"" + register "options.tsr[2].desc" = ""Ambient"" + + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 5500, + .max_power = 6000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 28 * MSECS_PER_SEC, + .granularity = 200 + }, + .pl2 = { + .min_power = 25000, + .max_power = 25000, + .time_window_min = 1, + .time_window_max = 1, + .granularity = 1000 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + device generic 0 on end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "enable_cnvi_ddr_rfim" = "true" + device generic 0 on end + end + end + device ref i2c3 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + end + device ref hda on + chip drivers/sof + register "jack_tplg" = "rt5682" + device generic 0 on end + end + end + device ref pcie_rp11 on + # Enable wlan PCIe 11 using clk 2 + register "pch_pcie_rp[PCH_RP(10)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + chip drivers/wifi/generic + register "wake" = "GPE0_DW1_03" + register "add_acpi_dma_property" = "true" + use usb2_port8 as bluetooth_companion + device pci 00.0 on end + end + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)" + register "srcclk_pin" = "2" + device generic 0 on end + end + end + device ref emmc on end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port2 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(BACK, RIGHT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, RIGHT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A1"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(2, 3))" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A2"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, CENTER, ACPI_PLD_GROUP(1, 2))" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A3"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, LEFT, ACPI_PLD_GROUP(1, 3))" + device ref usb2_port5 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A4"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, CENTER, ACPI_PLD_GROUP(2, 2))" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""CNVI Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A1"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, LEFT, ACPI_PLD_GROUP(2, 3)))" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A2"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, CENTER, ACPI_PLD_GROUP(1, 2))" + device ref usb3_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A3"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(FRONT, LEFT, ACPI_PLD_GROUP(1, 3))" + device ref usb3_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A4"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(BACK, CENTER, ACPI_PLD_GROUP(2, 2))" + device ref usb3_port4 on end + end + end + end + end + end end
-
Ivy Jian (Code Review)