Amanda Hwang has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/82714?usp=email )
Change subject: mb/google/trulo/var/orisa: Add overridetree ......................................................................
mb/google/trulo/var/orisa: Add overridetree
Add override devicetree based on schematics
BUG=b:333486830 BRANCH=firmware-nissa-15217.B TEST=emerge-nissa coreboot
Change-Id: Id3ceff41fdb8e4a57bd6dab6247b622a5d13587d Signed-off-by: Amanda Huang amanda_hwang@compal.corp-partner.google.com --- M src/mainboard/google/brya/Kconfig M src/mainboard/google/brya/variants/orisa/overridetree.cb 2 files changed, 522 insertions(+), 3 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/14/82714/1
diff --git a/src/mainboard/google/brya/Kconfig b/src/mainboard/google/brya/Kconfig index 366d2dd..9f6a026 100644 --- a/src/mainboard/google/brya/Kconfig +++ b/src/mainboard/google/brya/Kconfig @@ -687,7 +687,8 @@
config TPM_TIS_ACPI_INTERRUPT int - default 13 if !BOARD_GOOGLE_BASEBOARD_HADES # GPE0_DW0_13 (GPP_A13_IRQ) + default 13 if !BOARD_GOOGLE_BASEBOARD_HADES && !BOARD_GOOGLE_ORISA # GPE0_DW0_13 (GPP_A13_IRQ) + default 17 if BOARD_GOOGLE_ORISA # GPE0_DW0_17 (GPP_A17_IRQ) default 20 if BOARD_GOOGLE_BASEBOARD_HADES # GPE0_DW0_20 (GPP_A20_IRQ)
config OVERRIDE_DEVICETREE diff --git a/src/mainboard/google/brya/variants/orisa/overridetree.cb b/src/mainboard/google/brya/variants/orisa/overridetree.cb index 4f2c04a..0d20a3a 100644 --- a/src/mainboard/google/brya/variants/orisa/overridetree.cb +++ b/src/mainboard/google/brya/variants/orisa/overridetree.cb @@ -1,6 +1,524 @@ +fw_config + field THERMAL_SOLUTION 0 0 + option THERMAL_SOLUTION_6W 0 + option THERMAL_SOLUTION_15W 1 + end +end + chip soc/intel/alderlake + register "sagv" = "SaGv_Enabled"
- device domain 0 on - end + # GPE configuration + register "pmc_gpe0_dw1" = "GPP_B"
+ # S0ix enable + register "s0ix_enable" = "1" + + # DPTF enable + register "dptf_enable" = "1" + + register "tcc_offset" = "10" # TCC of 90 + + # Enable CNVi BT + register "cnvi_bt_core" = "true" + + # eMMC HS400 + register "emmc_enable_hs400_mode" = "1" + + #eMMC DLL tuning parameters + # EMMC Tx CMD Delay + # Refer to EDS-Vol2-42.3.7. + # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-42.3.8. + # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. + # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-42.3.9. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. + # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-42.3.10. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. + # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-42.3.12. + # [17:16] stands for Rx Clock before Output Buffer, + # 00: Rx clock after output buffer, + # 01: Rx clock before output buffer, + # 10: Automatic selection based on working mode. + # 11: Reserved + # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1004E" + + # EMMC Rx Strobe Delay + # Refer to EDS-Vol2-42.3.11. + # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. + # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x01515" + + register "usb2_ports[0]" = "USB2_PORT_MID(OC_SKIP)" # USB2_A0 + register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)" # USB2_A1 + register "usb2_ports[2]" = "USB2_PORT_MID(OC_SKIP)" # M.2 Camera + register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable USB2 Port 4 + register "usb2_ports[4]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C0 + register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN + register "usb2_ports[6]" = "USB2_PORT_EMPTY" # Disable USB2 Port 7 + register "usb2_ports[7]" = "USB2_PORT_EMPTY" # Disable USB2 Port 8 + register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A0 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A port A1 + + register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC_SKIP)" + + # Bit 0 - C0 has no redriver, so enable SBU muxing in the SoC. + # Bit 2 - C1 has a redriver which does SBU muxing. + # Bit 1,3 - AUX lines are not swapped on the motherboard for either C0 or C1. + register "tcss_aux_ori" = "0" + + # Configure external V1P05/Vnn/VnnSx Rails + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 1, + .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, + .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, + .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, + .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, + .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE, + .v1p05_voltage_mv = 1050, + .vnn_voltage_mv = 780, + .vnn_sx_voltage_mv = 1050, + .v1p05_icc_max_ma = 500, + .vnn_icc_max_ma = 500, + }" + + + register "serial_io_i2c_mode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoPci, + [PchSerialIoIndexI2C1] = PchSerialIoPci, + [PchSerialIoIndexI2C2] = PchSerialIoDisabled, + [PchSerialIoIndexI2C3] = PchSerialIoDisabled, + [PchSerialIoIndexI2C4] = PchSerialIoDisabled, + [PchSerialIoIndexI2C5] = PchSerialIoPci, + }" + + register "serial_io_gspi_mode" = "{ + [PchSerialIoIndexGSPI0] = PchSerialIoDisabled, + [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, + }" + + register "serial_io_uart_mode" = "{ + [PchSerialIoIndexUART0] = PchSerialIoPci, + [PchSerialIoIndexUART1] = PchSerialIoDisabled, + [PchSerialIoIndexUART2] = PchSerialIoDisabled, + }" + + # FIXME: To be enabled in future based on PNP impact data. + # Disable Package C-state demotion for nissa baseboard. + register "disable_package_c_state_demotion" = "1" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| I2C0 | TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C1 | Trackpad | + #| I2C5 | Touchscreen | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .early_init = 1, + .speed = I2C_SPEED_FAST_PLUS, + .speed_config[0] = { + .speed = I2C_SPEED_FAST_PLUS, + .scl_lcnt = 55, + .scl_hcnt = 30, + .sda_hold = 7, + } + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + }" + + register "power_limits_config[ADL_N_041_6W_CORE]" = "{ + .tdp_pl1_override = 20, + .tdp_pl2_override = 25, + .tdp_pl4 = 78, + }" + + register "power_limits_config[ADL_N_081_15W_CORE]" = "{ + .tdp_pl1_override = 20, + .tdp_pl2_override = 35, + .tdp_pl4 = 83, + }" + + device domain 0 on + device ref igpu on end + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DDR"" + register "options.tsr[1].desc" = ""charger"" + register "options.tsr[2].desc" = ""ambient"" + + ## Active Policy + register "policies.active" = "{ + [0] = { + .target = DPTF_CPU, + .thresholds = { + TEMP_PCT(70, 100), + TEMP_PCT(60, 65), + TEMP_PCT(42, 60), + TEMP_PCT(39, 55), + TEMP_PCT(38, 50), + TEMP_PCT(35, 43), + TEMP_PCT(31, 30), + } + }, + [1] = { + .target = DPTF_TEMP_SENSOR_0, + .thresholds = { + TEMP_PCT(60, 100), + TEMP_PCT(55, 65), + TEMP_PCT(52, 60), + TEMP_PCT(50, 55), + TEMP_PCT(48, 50), + TEMP_PCT(45, 43), + TEMP_PCT(41, 30), + } + } + }" + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 70, 5000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 70, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 70, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 95, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 95, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 95, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 6000, + .max_power = 20000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 28 * MSECS_PER_SEC, + .granularity = 500 + }, + .pl2 = { + .min_power = 25000, + .max_power = 25000, + .time_window_min = 32 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 500 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + ## Fan Performance Control (Percent, Speed, Noise, Power) + register "controls.fan_perf" = "{ + [0] = { 100, 6000, 220, 2200, }, + [1] = { 92, 5500, 180, 1800, }, + [2] = { 85, 5000, 145, 1450, }, + [3] = { 70, 4400, 115, 1150, }, + [4] = { 56, 3900, 90, 900, }, + [5] = { 45, 3300, 55, 550, }, + [6] = { 38, 3000, 30, 300, }, + [7] = { 33, 2900, 15, 150, }, + [8] = { 10, 800, 10, 100, }, + [9] = { 0, 0, 0, 50, } + }" + + ## Fan options + register "options.fan.fine_grained_control" = "1" + register "options.fan.step_size" = "2" + + device generic 0 on + probe THERMAL_SOLUTION THERMAL_SOLUTION_6W + end + end + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DDR"" + register "options.tsr[1].desc" = ""charger"" + register "options.tsr[2].desc" = ""ambient"" + + ## Active Policy + register "policies.active" = "{ + [0] = { + .target = DPTF_CPU, + .thresholds = { + TEMP_PCT(70, 100), + TEMP_PCT(60, 65), + TEMP_PCT(42, 58), + TEMP_PCT(39, 53), + TEMP_PCT(38, 47), + TEMP_PCT(35, 43), + TEMP_PCT(31, 30), + } + }, + [1] = { + .target = DPTF_TEMP_SENSOR_0, + .thresholds = { + TEMP_PCT(60, 100), + TEMP_PCT(55, 65), + TEMP_PCT(52, 58), + TEMP_PCT(50, 53), + TEMP_PCT(48, 47), + TEMP_PCT(45, 43), + TEMP_PCT(41, 30), + } + } + }" + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 70, 5000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 70, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 70, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 100, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 95, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 95, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 95, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 15000, + .max_power = 20000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 28 * MSECS_PER_SEC, + .granularity = 500 + }, + .pl2 = { + .min_power = 35000, + .max_power = 35000, + .time_window_min = 32 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 500 + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + ## Fan Performance Control (Percent, Speed, Noise, Power) + register "controls.fan_perf" = "{ + [0] = { 100, 6000, 220, 2200, }, + [1] = { 92, 5500, 180, 1800, }, + [2] = { 85, 5000, 145, 1450, }, + [3] = { 70, 4400, 115, 1150, }, + [4] = { 56, 3900, 90, 900, }, + [5] = { 45, 3300, 55, 550, }, + [6] = { 38, 3000, 30, 300, }, + [7] = { 33, 2900, 15, 150, }, + [8] = { 10, 800, 10, 100, }, + [9] = { 0, 0, 0, 50, } + }" + + ## Fan options + register "options.fan.fine_grained_control" = "1" + register "options.fan.step_size" = "2" + + device generic 1 on + probe THERMAL_SOLUTION THERMAL_SOLUTION_15W + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port1 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port5 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (DB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A13)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(LEFT, RIGHT, ACPI_PLD_GROUP(3, 1))" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A1 (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_A(RIGHT, LEFT, ACPI_PLD_GROUP(4, 1))" + device ref usb3_port2 on end + end + end + end + end + device ref shared_sram on end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + register "enable_cnvi_ddr_rfim" = "true" + register "add_acpi_dma_property" = "true" + device generic 0 on end + end + end + device ref i2c0 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A17_IRQ)" + device i2c 50 on end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_B3_IRQ)" + register "wake" = "GPE0_DW1_03" + register "detect" = "1" + device i2c 15 on end + end + end #I2C1 + device ref i2c5 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9004"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_D16_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D15)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E17)" + register "generic.enable_delay_ms" = "1" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A21)" + register "generic.stop_delay_ms" = "150" + register "generic.stop_off_delay_ms" = "2" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end #I2C5 + device ref heci1 on end + device ref pcie_rp7 off end + device ref emmc on end + device ref uart0 on end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port5 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + end + end + end + end end
-
Amanda Hwang (Code Review)