Matt DeVillier has submitted this change. ( https://review.coreboot.org/c/coreboot/+/39964 )
Change subject: mb/google/cyan: convert to overridetree ......................................................................
mb/google/cyan: convert to overridetree
Simply cyan variants by converting to overridetree format.
A few differences were ignored as there appears to be no reason behind them:
- cyan had PCIe RP2 enabled, but nothing is attached to it - kefka had the SPI 1 device disabled - reks, relm, and ultima had HSUART 1 disabled - edgar had I2C1 UPD disabled
Test: build/boot cyan and edgar variants, verify everything still works
Change-Id: I9928cc59adcfda4661ddfdfa95f53a7820053b4a Signed-off-by: Matt DeVillier matt.devillier@gmail.com Reviewed-on: https://review.coreboot.org/c/coreboot/+/39964 Reviewed-by: Angel Pons th3fanbus@gmail.com Tested-by: build bot (Jenkins) no-reply@coreboot.org --- M src/mainboard/google/cyan/Kconfig R src/mainboard/google/cyan/devicetree.cb D src/mainboard/google/cyan/variants/banon/devicetree.cb A src/mainboard/google/cyan/variants/banon/overridetree.cb D src/mainboard/google/cyan/variants/celes/devicetree.cb A src/mainboard/google/cyan/variants/celes/overridetree.cb D src/mainboard/google/cyan/variants/cyan/devicetree.cb A src/mainboard/google/cyan/variants/cyan/overridetree.cb D src/mainboard/google/cyan/variants/edgar/devicetree.cb A src/mainboard/google/cyan/variants/edgar/overridetree.cb D src/mainboard/google/cyan/variants/kefka/devicetree.cb A src/mainboard/google/cyan/variants/kefka/overridetree.cb D src/mainboard/google/cyan/variants/reks/devicetree.cb A src/mainboard/google/cyan/variants/reks/overridetree.cb D src/mainboard/google/cyan/variants/relm/devicetree.cb A src/mainboard/google/cyan/variants/relm/overridetree.cb D src/mainboard/google/cyan/variants/setzer/devicetree.cb A src/mainboard/google/cyan/variants/setzer/overridetree.cb A src/mainboard/google/cyan/variants/terra/overridetree.cb D src/mainboard/google/cyan/variants/ultima/devicetree.cb A src/mainboard/google/cyan/variants/ultima/overridetree.cb D src/mainboard/google/cyan/variants/wizpig/devicetree.cb A src/mainboard/google/cyan/variants/wizpig/overridetree.cb 23 files changed, 216 insertions(+), 1,455 deletions(-)
Approvals: build bot (Jenkins): Verified Angel Pons: Looks good to me, approved
diff --git a/src/mainboard/google/cyan/Kconfig b/src/mainboard/google/cyan/Kconfig index 4561054..92bafee 100644 --- a/src/mainboard/google/cyan/Kconfig +++ b/src/mainboard/google/cyan/Kconfig @@ -68,9 +68,9 @@ default "Ultima" if BOARD_GOOGLE_ULTIMA default "Wizpig" if BOARD_GOOGLE_WIZPIG
-config DEVICETREE +config OVERRIDE_DEVICETREE string - default "variants/$(CONFIG_VARIANT_DIR)/devicetree.cb" + default "variants/$(CONFIG_VARIANT_DIR)/overridetree.cb"
config CBFS_SIZE hex diff --git a/src/mainboard/google/cyan/variants/terra/devicetree.cb b/src/mainboard/google/cyan/devicetree.cb similarity index 74% rename from src/mainboard/google/cyan/variants/terra/devicetree.cb rename to src/mainboard/google/cyan/devicetree.cb index d7d0f1f..328a608 100644 --- a/src/mainboard/google/cyan/variants/terra/devicetree.cb +++ b/src/mainboard/google/cyan/devicetree.cb @@ -27,12 +27,12 @@ register "PcdEnableLpe" = "1" register "PcdEnableDma0" = "1" register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "0" - register "PcdEnableI2C1" = "1" + register "PcdEnableI2C0" = "0" # Touchscreen + register "PcdEnableI2C1" = "1" # PMIC (or Maxim Audio) register "PcdEnableI2C2" = "0" register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" + register "PcdEnableI2C4" = "1" # Realtek Audio + register "PcdEnableI2C5" = "1" # Touchpad register "PcdEnableI2C6" = "0" register "PunitPwrConfigDisable" = "0" # Enable SVID register "ChvSvidConfig" = "SVID_PMIC_CONFIG" @@ -67,13 +67,14 @@ register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" register "PcdSataInterfaceSpeed" = "3" register "PcdPchSsicEnable" = "1" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM + register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM register "PMIC_I2CBus" = "1" register "ISPEnable" = "0" # Disable IUNIT register "ISPPciDevConfig" = "3" register "PcdSdDetectChk" = "0" # Disable SD card detect + register "I2C0Frequency" = "1" - register "I2C1Frequency" = "2" # Set the PMIC clock speed to 1Mhz + register "I2C1Frequency" = "2" # Set the PMIC clock speed to 1Mhz register "I2C2Frequency" = "1" register "I2C3Frequency" = "1" register "I2C4Frequency" = "1" @@ -100,37 +101,37 @@ end device domain 0 on # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display + device pci 00.0 on end # 8086 2280 - SoC transaction router + device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port + device pci 0b.0 on end # 8086 22dc - Signal Processing Controller + device pci 10.0 on end # 8086 2294 - MMC Port device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port + device pci 12.0 on end # 8086 0F16 - SD Port device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio + device pci 14.0 on end # 8086 22b5 - USB XHCI + device pci 15.0 on end # 8086 22a8 - LP Engine Audio device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 off end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 + device pci 18.0 on end # 8086 22c0 - SIO - DMA + device pci 18.1 off end # 8086 22c1 - I2C Port 1: Touchscreen + device pci 18.2 on end # 8086 22c2 - I2C Port 2: PMIC device pci 18.3 off end # 8086 22c3 - I2C Port 3 device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 + device pci 18.5 on end # 8086 22c5 - I2C Port 5: Realtek Audio + device pci 18.6 on end # 8086 22c6 - I2C Port 6: Touchpad device pci 18.7 off end # 8086 22c7 - I2C Port 7 device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA + device pci 1b.0 on end # 8086 2284 - HD Audio + device pci 1c.0 on end # 8086 22c8 - PCIe Root Port 1 + device pci 1c.1 off end # 8086 22ca - PCIe Root Port 2 + device pci 1c.2 on end # 8086 22cc - PCIe Root Port 3: WiFi + device pci 1c.3 off end # 8086 22ce - PCIe Root Port 4 + device pci 1e.0 on end # 8086 2286 - SIO - DMA device pci 1e.1 off end # 8086 0F08 - PWM 1 device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 + device pci 1e.3 on end # 8086 228a - HSUART 1 device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 + device pci 1e.5 on end # 8086 228e - SPI 1 device pci 1e.6 off end # 8086 2290 - SPI 2 device pci 1e.7 off end # 8086 22ac - SPI 3 device pci 1f.0 on # 8086 229c - LPC bridge diff --git a/src/mainboard/google/cyan/variants/banon/devicetree.cb b/src/mainboard/google/cyan/variants/banon/devicetree.cb deleted file mode 100644 index 60076c2..0000000 --- a/src/mainboard/google/cyan/variants/banon/devicetree.cb +++ /dev/null @@ -1,146 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "0" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "6" - register "Usb2Port0IUsbTxEmphasisEn" = "3" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "6" - register "Usb2Port1IUsbTxEmphasisEn" = "3" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "6" - register "Usb2Port2IUsbTxEmphasisEn" = "3" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "6" - register "Usb2Port3IUsbTxEmphasisEn" = "3" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "6" - register "Usb2Port4IUsbTxEmphasisEn" = "3" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "1" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - register "I2C0Frequency" = "1" - register "I2C1Frequency" = "2" # Set the PMIC clock speed to 1Mhz - register "I2C2Frequency" = "1" - register "I2C3Frequency" = "1" - register "I2C4Frequency" = "1" - register "I2C5Frequency" = "1" - register "I2C6Frequency" = "1" - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 off end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/banon/overridetree.cb b/src/mainboard/google/cyan/variants/banon/overridetree.cb new file mode 100644 index 0000000..32f0dc6 --- /dev/null +++ b/src/mainboard/google/cyan/variants/banon/overridetree.cb @@ -0,0 +1,26 @@ +chip soc/intel/braswell + + register "Usb2Port0PerPortPeTxiSet" = "7" + register "Usb2Port0PerPortTxiSet" = "6" + register "Usb2Port0IUsbTxEmphasisEn" = "3" + register "Usb2Port0PerPortTxPeHalf" = "1" + register "Usb2Port1PerPortPeTxiSet" = "7" + register "Usb2Port1PerPortTxiSet" = "6" + register "Usb2Port1IUsbTxEmphasisEn" = "3" + register "Usb2Port1PerPortTxPeHalf" = "1" + register "Usb2Port2PerPortPeTxiSet" = "7" + register "Usb2Port2PerPortTxiSet" = "6" + register "Usb2Port2IUsbTxEmphasisEn" = "3" + register "Usb2Port2PerPortTxPeHalf" = "1" + register "Usb2Port3PerPortPeTxiSet" = "7" + register "Usb2Port3PerPortTxiSet" = "6" + register "Usb2Port3IUsbTxEmphasisEn" = "3" + register "Usb2Port3PerPortTxPeHalf" = "1" + register "Usb2Port4PerPortPeTxiSet" = "7" + register "Usb2Port4PerPortTxiSet" = "6" + register "Usb2Port4IUsbTxEmphasisEn" = "3" + register "Usb2Port4PerPortTxPeHalf" = "1" + + device domain 0 on end + +end diff --git a/src/mainboard/google/cyan/variants/celes/devicetree.cb b/src/mainboard/google/cyan/variants/celes/devicetree.cb deleted file mode 100644 index a1ab510..0000000 --- a/src/mainboard/google/cyan/variants/celes/devicetree.cb +++ /dev/null @@ -1,140 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "0" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "3" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "3" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "0" - register "PcdPchUsbHsicPort" = "0" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 off end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/celes/overridetree.cb b/src/mainboard/google/cyan/variants/celes/overridetree.cb new file mode 100644 index 0000000..1eabd8e --- /dev/null +++ b/src/mainboard/google/cyan/variants/celes/overridetree.cb @@ -0,0 +1,8 @@ +chip soc/intel/braswell + + register "PcdPchSsicEnable" = "0" + register "PcdPchUsbHsicPort" = "0" + + device domain 0 on end + +end diff --git a/src/mainboard/google/cyan/variants/cyan/devicetree.cb b/src/mainboard/google/cyan/variants/cyan/devicetree.cb deleted file mode 100644 index dd9b05e..0000000 --- a/src/mainboard/google/cyan/variants/cyan/devicetree.cb +++ /dev/null @@ -1,139 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "0" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "1" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "0" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_CONFIG1" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "3" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "3" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "1" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "0" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 on end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 off end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 2284 - HD Audio - device pci 1c.0 on end # 8086 22c8 - PCIe Root Port 1 - device pci 1c.1 on end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 22cc - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/cyan/overridetree.cb b/src/mainboard/google/cyan/variants/cyan/overridetree.cb new file mode 100644 index 0000000..10df7ab --- /dev/null +++ b/src/mainboard/google/cyan/variants/cyan/overridetree.cb @@ -0,0 +1,18 @@ +chip soc/intel/braswell + + register "PcdCaMirrorEn" = "0" + + register "PcdEnableI2C0" = "1" # Touchscreen + register "PcdEnableI2C4" = "0" # No Realtek Audio + + register "ChvSvidConfig" = "SVID_CONFIG1" + + register "PMIC_I2CBus" = "0" + + register "I2C1Frequency" = "1" + + device domain 0 on + device pci 18.1 on end # 8086 22c1 - I2C Port 1: Touchscreen + device pci 18.5 off end # 8086 22c5 - I2C Port 5: Realtek Audio + end +end diff --git a/src/mainboard/google/cyan/variants/edgar/devicetree.cb b/src/mainboard/google/cyan/variants/edgar/devicetree.cb deleted file mode 100644 index 0ba221e..0000000 --- a/src/mainboard/google/cyan/variants/edgar/devicetree.cb +++ /dev/null @@ -1,140 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_DISABLED" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "0" - register "PcdEnableI2C1" = "0" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "3" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "6" - register "Usb2Port3IUsbTxEmphasisEn" = "3" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "0" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "0" - register "PcdPchUsbHsicPort" = "0" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 off end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 off end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/edgar/overridetree.cb b/src/mainboard/google/cyan/variants/edgar/overridetree.cb new file mode 100644 index 0000000..48b1013 --- /dev/null +++ b/src/mainboard/google/cyan/variants/edgar/overridetree.cb @@ -0,0 +1,32 @@ +chip soc/intel/braswell + + register "PcdSdcardMode" = "PCH_DISABLED" + + register "Usb2Port0PerPortPeTxiSet" = "7" + register "Usb2Port0PerPortTxiSet" = "5" + register "Usb2Port0IUsbTxEmphasisEn" = "2" + register "Usb2Port0PerPortTxPeHalf" = "1" + register "Usb2Port1PerPortPeTxiSet" = "7" + register "Usb2Port1PerPortTxiSet" = "3" + register "Usb2Port1IUsbTxEmphasisEn" = "2" + register "Usb2Port1PerPortTxPeHalf" = "1" + register "Usb2Port2PerPortPeTxiSet" = "7" + register "Usb2Port2PerPortTxiSet" = "3" + register "Usb2Port2IUsbTxEmphasisEn" = "2" + register "Usb2Port2PerPortTxPeHalf" = "1" + register "Usb2Port3PerPortPeTxiSet" = "7" + register "Usb2Port3PerPortTxiSet" = "6" + register "Usb2Port3IUsbTxEmphasisEn" = "3" + register "Usb2Port3PerPortTxPeHalf" = "1" + register "Usb2Port4PerPortPeTxiSet" = "7" + register "Usb2Port4PerPortTxiSet" = "0" + register "Usb2Port4IUsbTxEmphasisEn" = "2" + register "Usb2Port4PerPortTxPeHalf" = "1" + + register "PcdPchSsicEnable" = "0" + register "PcdPchUsbHsicPort" = "0" + + device domain 0 on + device pci 12.0 off end # 8086 0F16 - SD Port + end +end diff --git a/src/mainboard/google/cyan/variants/kefka/devicetree.cb b/src/mainboard/google/cyan/variants/kefka/devicetree.cb deleted file mode 100644 index 807dbcb..0000000 --- a/src/mainboard/google/cyan/variants/kefka/devicetree.cb +++ /dev/null @@ -1,146 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "1" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "3" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "3" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "1" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - register "I2C0Frequency" = "1" - register "I2C1Frequency" = "2" # Set the PMIC clock speed to 1Mhz - register "I2C2Frequency" = "1" - register "I2C3Frequency" = "1" - register "I2C4Frequency" = "1" - register "I2C5Frequency" = "1" - register "I2C6Frequency" = "1" - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 on end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 off end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/kefka/overridetree.cb b/src/mainboard/google/cyan/variants/kefka/overridetree.cb new file mode 100644 index 0000000..41908e0 --- /dev/null +++ b/src/mainboard/google/cyan/variants/kefka/overridetree.cb @@ -0,0 +1,8 @@ +chip soc/intel/braswell + + register "PcdEnableI2C0" = "1" # Touchscreen + + device domain 0 on + device pci 18.1 on end # 8086 22c1 - I2C Port 1: Touchscreen + end +end diff --git a/src/mainboard/google/cyan/variants/reks/devicetree.cb b/src/mainboard/google/cyan/variants/reks/devicetree.cb deleted file mode 100644 index 302f2da..0000000 --- a/src/mainboard/google/cyan/variants/reks/devicetree.cb +++ /dev/null @@ -1,137 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "1" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "7" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "3" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "1" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 on end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 off end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/reks/overridetree.cb b/src/mainboard/google/cyan/variants/reks/overridetree.cb new file mode 100644 index 0000000..9b10656 --- /dev/null +++ b/src/mainboard/google/cyan/variants/reks/overridetree.cb @@ -0,0 +1,29 @@ +chip soc/intel/braswell + + register "PcdEnableI2C0" = "1" # Touchscreen + + register "Usb2Port0PerPortPeTxiSet" = "7" + register "Usb2Port0PerPortTxiSet" = "5" + register "Usb2Port0IUsbTxEmphasisEn" = "2" + register "Usb2Port0PerPortTxPeHalf" = "1" + register "Usb2Port1PerPortPeTxiSet" = "7" + register "Usb2Port1PerPortTxiSet" = "7" + register "Usb2Port1IUsbTxEmphasisEn" = "2" + register "Usb2Port1PerPortTxPeHalf" = "1" + register "Usb2Port2PerPortPeTxiSet" = "7" + register "Usb2Port2PerPortTxiSet" = "3" + register "Usb2Port2IUsbTxEmphasisEn" = "2" + register "Usb2Port2PerPortTxPeHalf" = "1" + register "Usb2Port3PerPortPeTxiSet" = "7" + register "Usb2Port3PerPortTxiSet" = "3" + register "Usb2Port3IUsbTxEmphasisEn" = "2" + register "Usb2Port3PerPortTxPeHalf" = "1" + register "Usb2Port4PerPortPeTxiSet" = "7" + register "Usb2Port4PerPortTxiSet" = "3" + register "Usb2Port4IUsbTxEmphasisEn" = "2" + register "Usb2Port4PerPortTxPeHalf" = "1" + + device domain 0 on + device pci 18.1 on end # 8086 22c1 - I2C Port 1: Touchscreen + end +end diff --git a/src/mainboard/google/cyan/variants/relm/devicetree.cb b/src/mainboard/google/cyan/variants/relm/devicetree.cb deleted file mode 100644 index e1bbb0a..0000000 --- a/src/mainboard/google/cyan/variants/relm/devicetree.cb +++ /dev/null @@ -1,146 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "1" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "3" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "3" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "1" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - register "I2C0Frequency" = "1" - register "I2C1Frequency" = "2" # Set the PMIC clock speed to 1Mhz - register "I2C2Frequency" = "1" - register "I2C3Frequency" = "1" - register "I2C4Frequency" = "1" - register "I2C5Frequency" = "1" - register "I2C6Frequency" = "1" - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 on end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 off end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/relm/overridetree.cb b/src/mainboard/google/cyan/variants/relm/overridetree.cb new file mode 100644 index 0000000..41908e0 --- /dev/null +++ b/src/mainboard/google/cyan/variants/relm/overridetree.cb @@ -0,0 +1,8 @@ +chip soc/intel/braswell + + register "PcdEnableI2C0" = "1" # Touchscreen + + device domain 0 on + device pci 18.1 on end # 8086 22c1 - I2C Port 1: Touchscreen + end +end diff --git a/src/mainboard/google/cyan/variants/setzer/devicetree.cb b/src/mainboard/google/cyan/variants/setzer/devicetree.cb deleted file mode 100644 index f0b2c6f..0000000 --- a/src/mainboard/google/cyan/variants/setzer/devicetree.cb +++ /dev/null @@ -1,146 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "1" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "3" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "3" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "0" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - register "I2C0Frequency" = "1" - register "I2C1Frequency" = "2" # Set the PMIC clock speed to 1Mhz - register "I2C2Frequency" = "1" - register "I2C3Frequency" = "1" - register "I2C4Frequency" = "1" - register "I2C5Frequency" = "1" - register "I2C6Frequency" = "1" - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 on end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/setzer/overridetree.cb b/src/mainboard/google/cyan/variants/setzer/overridetree.cb new file mode 100644 index 0000000..d3d7f8d --- /dev/null +++ b/src/mainboard/google/cyan/variants/setzer/overridetree.cb @@ -0,0 +1,10 @@ +chip soc/intel/braswell + + register "PcdEnableI2C0" = "1" # Touchscreen + + register "PcdPchSsicEnable" = "0" + + device domain 0 on + device pci 18.1 on end # 8086 22c1 - I2C Port 1: Touchscreen + end +end diff --git a/src/mainboard/google/cyan/variants/terra/overridetree.cb b/src/mainboard/google/cyan/variants/terra/overridetree.cb new file mode 100644 index 0000000..8b6b007 --- /dev/null +++ b/src/mainboard/google/cyan/variants/terra/overridetree.cb @@ -0,0 +1,5 @@ +chip soc/intel/braswell + + device domain 0 on end + +end diff --git a/src/mainboard/google/cyan/variants/ultima/devicetree.cb b/src/mainboard/google/cyan/variants/ultima/devicetree.cb deleted file mode 100644 index d4ed38b..0000000 --- a/src/mainboard/google/cyan/variants/ultima/devicetree.cb +++ /dev/null @@ -1,140 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "0" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "1" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "5" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "3" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "3" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "3" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "0" - register "PcdPchUsbHsicPort" = "0" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 on end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 2284 - HD Audio - device pci 1c.0 on end # 8086 22c8 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 22cc - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 off end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/ultima/overridetree.cb b/src/mainboard/google/cyan/variants/ultima/overridetree.cb new file mode 100644 index 0000000..b5aa652 --- /dev/null +++ b/src/mainboard/google/cyan/variants/ultima/overridetree.cb @@ -0,0 +1,11 @@ +chip soc/intel/braswell + + register "PcdEnableI2C0" = "1" # Touchscreen + + register "PcdPchSsicEnable" = "0" + register "PcdPchUsbHsicPort" = "0" + + device domain 0 on + device pci 18.1 on end # 8086 22c1 - I2C Port 1: Touchscreen + end +end diff --git a/src/mainboard/google/cyan/variants/wizpig/devicetree.cb b/src/mainboard/google/cyan/variants/wizpig/devicetree.cb deleted file mode 100644 index 7be7a0f..0000000 --- a/src/mainboard/google/cyan/variants/wizpig/devicetree.cb +++ /dev/null @@ -1,147 +0,0 @@ -chip soc/intel/braswell - - ############################################################ - # Set the parameters for MemoryInit - ############################################################ - - register "PcdMrcInitTsegSize" = "8" # SMM Region size in MiB - - register "PcdMrcInitMmioSize" = "0x0800" - register "PcdMrcInitSpdAddr1" = "0xa0" - register "PcdMrcInitSpdAddr2" = "0xa2" - register "PcdIgdDvmt50PreAlloc" = "1" - register "PcdApertureSize" = "2" - register "PcdGttSize" = "1" - register "PcdDvfsEnable" = "1" - register "PcdCaMirrorEn" = "1" - - ############################################################ - # Set the parameters for SiliconInit - ############################################################ - - register "PcdSdcardMode" = "PCH_ACPI_MODE" - register "PcdEnableHsuart0" = "0" - register "PcdEnableHsuart1" = "1" - register "PcdEnableAzalia" = "1" - register "PcdEnableXhci" = "1" - register "PcdEnableLpe" = "1" - register "PcdEnableDma0" = "1" - register "PcdEnableDma1" = "1" - register "PcdEnableI2C0" = "1" - register "PcdEnableI2C1" = "1" - register "PcdEnableI2C2" = "0" - register "PcdEnableI2C3" = "0" - register "PcdEnableI2C4" = "1" - register "PcdEnableI2C5" = "1" - register "PcdEnableI2C6" = "0" - register "PunitPwrConfigDisable" = "0" # Enable SVID - register "ChvSvidConfig" = "SVID_PMIC_CONFIG" - register "PcdEmmcMode" = "PCH_ACPI_MODE" - register "PcdUsb3ClkSsc" = "1" - register "PcdDispClkSsc" = "1" - register "PcdSataClkSsc" = "1" - register "PcdEnableSata" = "0" # Disable SATA - register "Usb2Port0PerPortPeTxiSet" = "7" - register "Usb2Port0PerPortTxiSet" = "0" - register "Usb2Port0IUsbTxEmphasisEn" = "2" - register "Usb2Port0PerPortTxPeHalf" = "1" - register "Usb2Port1PerPortPeTxiSet" = "7" - register "Usb2Port1PerPortTxiSet" = "0" - register "Usb2Port1IUsbTxEmphasisEn" = "2" - register "Usb2Port1PerPortTxPeHalf" = "1" - register "Usb2Port2PerPortPeTxiSet" = "7" - register "Usb2Port2PerPortTxiSet" = "0" - register "Usb2Port2IUsbTxEmphasisEn" = "2" - register "Usb2Port2PerPortTxPeHalf" = "1" - register "Usb2Port3PerPortPeTxiSet" = "7" - register "Usb2Port3PerPortTxiSet" = "0" - register "Usb2Port3IUsbTxEmphasisEn" = "2" - register "Usb2Port3PerPortTxPeHalf" = "1" - register "Usb2Port4PerPortPeTxiSet" = "7" - register "Usb2Port4PerPortTxiSet" = "3" - register "Usb2Port4IUsbTxEmphasisEn" = "2" - register "Usb2Port4PerPortTxPeHalf" = "1" - register "Usb3Lane0Ow2tapgen2deemph3p5" = "0x3a" - register "Usb3Lane1Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane2Ow2tapgen2deemph3p5" = "0x64" - register "Usb3Lane3Ow2tapgen2deemph3p5" = "0x3a" - register "PcdSataInterfaceSpeed" = "3" - register "PcdPchSsicEnable" = "0" - register "PcdPchUsbHsicPort" = "0" - register "PcdRtcLock" = "0" # Disable RTC access locking to NVRAM - register "PMIC_I2CBus" = "1" - register "ISPEnable" = "0" # Disable IUNIT - register "ISPPciDevConfig" = "3" - register "PcdSdDetectChk" = "0" # Disable SD card detect - register "I2C0Frequency" = "1" - register "I2C1Frequency" = "2" # Set the PMIC clock speed to 1Mhz - register "I2C2Frequency" = "1" - register "I2C3Frequency" = "1" - register "I2C4Frequency" = "1" - register "I2C5Frequency" = "1" - register "I2C6Frequency" = "1" - - # LPE audio codec settings - register "lpe_codec_clk_src" = "LPE_CLK_SRC_XTAL" # 19.2MHz clock - - # Enable devices in ACPI mode - register "lpss_acpi_mode" = "1" - register "emmc_acpi_mode" = "1" - register "sd_acpi_mode" = "1" - register "lpe_acpi_mode" = "1" - - # Disable SLP_X stretching after SUS power well fail. - register "disable_slp_x_stretch_sus_fail" = "1" - - # Allow PCIe devices to wake system from suspend - register "pcie_wake_enable" = "1" - - device cpu_cluster 0 on - device lapic 0 on end - end - device domain 0 on - # EDS Table 24-4, Figure 24-5 - device pci 00.0 on end # 8086 2280 - SoC transaction router - device pci 02.0 on end # 8086 22b0/22b1 - B1/C0 stepping Graphics and Display - device pci 03.0 off end # 8086 22b8 - Camera and Image Processor - device pci 0b.0 on end # 8086 22dc - ? - device pci 10.0 on end # 8086 2294 - MMC Port - device pci 11.0 off end # 8086 0F15 - SDIO Port - device pci 12.0 on end # 8086 0F16 - SD Port - device pci 13.0 off end # 8086 22a3 - Sata controller - device pci 14.0 on end # 8086 22b5 - USB XHCI - Only 1 USB controller at a time - device pci 15.0 on end # 8086 22a8 - LP Engine Audio - device pci 16.0 off end # 8086 22b7 - USB device - device pci 18.0 on end # 8086 22c0 - SIO - DMA - device pci 18.1 on end # 8086 22c1 - I2C Port 1 - device pci 18.2 on end # 8086 22c2 - I2C Port 2 - device pci 18.3 off end # 8086 22c3 - I2C Port 3 - device pci 18.4 off end # 8086 22c4 - I2C Port 4 - device pci 18.5 on end # 8086 22c5 - I2C Port 5 - device pci 18.6 on end # 8086 22c6 - I2C Port 6 - device pci 18.7 off end # 8086 22c7 - I2C Port 7 - device pci 1a.0 off end # 8086 0F18 - Trusted Execution Engine - device pci 1b.0 on end # 8086 0F04 - HD Audio - device pci 1c.0 on end # 8086 0000 - PCIe Root Port 1 - device pci 1c.1 off end # 8086 0000 - PCIe Root Port 2 - device pci 1c.2 on end # 8086 0000 - PCIe Root Port 3 - device pci 1c.3 off end # 8086 0000 - PCIe Root Port 4 - device pci 1e.0 on end # 8086 2286 - SIO - DMA - device pci 1e.1 off end # 8086 0F08 - PWM 1 - device pci 1e.2 off end # 8086 0F09 - PWM 2 - device pci 1e.3 on end # 8086 228a - HSUART 1 - device pci 1e.4 off end # 8086 228c - HSUART 2 - device pci 1e.5 on end # 8086 228e - SPI 1 - device pci 1e.6 off end # 8086 2290 - SPI 2 - device pci 1e.7 off end # 8086 22ac - SPI 3 - device pci 1f.0 on # 8086 229c - LPC bridge - chip drivers/pc80/tpm - device pnp 0c31.0 on end - end - chip ec/google/chromeec - device pnp 0c09.0 on end - end - end # LPC Bridge - device pci 1f.3 off end # 8086 0F12 - SMBus 0 - end -end diff --git a/src/mainboard/google/cyan/variants/wizpig/overridetree.cb b/src/mainboard/google/cyan/variants/wizpig/overridetree.cb new file mode 100644 index 0000000..5923462 --- /dev/null +++ b/src/mainboard/google/cyan/variants/wizpig/overridetree.cb @@ -0,0 +1,32 @@ +chip soc/intel/braswell + + register "PcdEnableI2C0" = "1" # Touchscreen + + register "Usb2Port0PerPortPeTxiSet" = "7" + register "Usb2Port0PerPortTxiSet" = "0" + register "Usb2Port0IUsbTxEmphasisEn" = "2" + register "Usb2Port0PerPortTxPeHalf" = "1" + register "Usb2Port1PerPortPeTxiSet" = "7" + register "Usb2Port1PerPortTxiSet" = "0" + register "Usb2Port1IUsbTxEmphasisEn" = "2" + register "Usb2Port1PerPortTxPeHalf" = "1" + register "Usb2Port2PerPortPeTxiSet" = "7" + register "Usb2Port2PerPortTxiSet" = "0" + register "Usb2Port2IUsbTxEmphasisEn" = "2" + register "Usb2Port2PerPortTxPeHalf" = "1" + register "Usb2Port3PerPortPeTxiSet" = "7" + register "Usb2Port3PerPortTxiSet" = "0" + register "Usb2Port3IUsbTxEmphasisEn" = "2" + register "Usb2Port3PerPortTxPeHalf" = "1" + register "Usb2Port4PerPortPeTxiSet" = "7" + register "Usb2Port4PerPortTxiSet" = "3" + register "Usb2Port4IUsbTxEmphasisEn" = "2" + register "Usb2Port4PerPortTxPeHalf" = "1" + + register "PcdPchSsicEnable" = "0" + register "PcdPchUsbHsicPort" = "0" + + device domain 0 on + device pci 18.1 on end # 8086 22c1 - I2C Port 1: Touchscreen + end +end