[coreboot-gerrit] Change in coreboot[master]: soc/intel/icelake: Make use of common thermal code for ICL

[Subrata Banik (Code Review)]

Subrata Banik has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/34649 )

Change subject: soc/intel/icelake: Make use of common thermal code for ICL
......................................................................

soc/intel/icelake: Make use of common thermal code for ICL

This patch ports CB:34522 and CB:33147 changes from CNL to ICL.

TEST=Build and boot dragonegg

Change-Id: I0b983005f16fe182e634eac63fef4f6b22197a85
Signed-off-by: Subrata Banik 
---
M src/mainboard/google/dragonegg/variants/baseboard/devicetree.cb
M src/soc/intel/icelake/Kconfig
M src/soc/intel/icelake/finalize.c
3 files changed, 14 insertions(+), 1 deletion(-)

git pull ssh://review.coreboot.org:29418/coreboot refs/changes/49/34649/1

diff --git a/src/mainboard/google/dragonegg/variants/baseboard/devicetree.cb b/src/mainboard/google/dragonegg/variants/baseboard/devicetree.cb
index b3b93f5..f49e1c9 100644
--- a/src/mainboard/google/dragonegg/variants/baseboard/devicetree.cb
+++ b/src/mainboard/google/dragonegg/variants/baseboard/devicetree.cb
@@ -148,6 +148,7 @@
    #|                   | required to set up a BAR  |
    #|                   | for TPM communication     |
    #|                   | before memory is up       |
+	#| pch_thermal_trip  | PCH Trip Temperature      |
    #+-------------------+---------------------------+

register "common_soc_config" = "{
@@ -165,6 +166,7 @@
    			.sda_hold = 36,
    		}
    	},
+		.pch_thermal_trip = "77",
    }"

# GPIO PM programming
@@ -181,7 +183,7 @@
    	device pci 00.0 on  end # Host Bridge
    	device pci 02.0 on  end # Integrated Graphics Device
    	device pci 04.0 off  end # SA Thermal device
-		device pci 12.0 off  end # Thermal Subsystem
+		device pci 12.0 on  end # Thermal Subsystem
    	device pci 12.5 off end # UFS SCS
    	device pci 12.6 off end # GSPI #2
    	device pci 14.0 on
diff --git a/src/soc/intel/icelake/Kconfig b/src/soc/intel/icelake/Kconfig
index 99000bb..3ad50cf 100644
--- a/src/soc/intel/icelake/Kconfig
+++ b/src/soc/intel/icelake/Kconfig
@@ -51,6 +51,7 @@
    select SOC_INTEL_COMMON_BLOCK_SA
    select SOC_INTEL_COMMON_BLOCK_SMM
    select SOC_INTEL_COMMON_BLOCK_SMM_IO_TRAP
+	select SOC_INTEL_COMMON_BLOCK_THERMAL
    select SOC_INTEL_COMMON_PCH_BASE
    select SOC_INTEL_COMMON_RESET
    select SSE2
diff --git a/src/soc/intel/icelake/finalize.c b/src/soc/intel/icelake/finalize.c
index c969f3b..086787d 100644
--- a/src/soc/intel/icelake/finalize.c
+++ b/src/soc/intel/icelake/finalize.c
@@ -23,6 +23,7 @@
 #include <intelblocks/lpc_lib.h>
 #include <intelblocks/pcr.h>
 #include <intelblocks/tco.h>
+#include <intelblocks/thermal.h>
 #include <reg_script.h>
 #include <spi-generic.h>
 #include <soc/p2sb.h>
@@ -63,6 +64,15 @@
    tco_lockdown();

/*
+	 * Set low maximum temp threshold value used for dynamic thermal sensor
+	 * shutdown consideration.
+	 *
+	 * If Dynamic Thermal Shutdown is enabled then PMC logic shuts down the
+	 * thermal sensor when CPU is in a C-state and DTS Temp <= LTT.
+	 */
+	pch_thermal_configuration();
+
+	/*
     * Disable ACPI PM timer based on dt policy
     *
     * Disabling ACPI PM timer is necessary for XTAL OSC shutdown.