Leo Chou has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/81653?usp=email )
Change subject: mb/google/nissa/variant/sundance: Update devicetree settings ......................................................................
mb/google/nissa/variant/sundance: Update devicetree settings
Based on schematic and gpio table of sundance, generate overridetree.cb settings for sundance.
BUG=b:328505938 TEST=FW_NAME=sundance emerge-nissa coreboot chromeos-bootimage
Change-Id: I857be7bc7f98281cac57fef85bf9f3cef2ec14e9 Signed-off-by: Leo Chou leo.chou@lcfc.corp-partner.google.com --- M src/mainboard/google/brya/Kconfig M src/mainboard/google/brya/variants/sundance/overridetree.cb 2 files changed, 343 insertions(+), 2 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/53/81653/1
diff --git a/src/mainboard/google/brya/Kconfig b/src/mainboard/google/brya/Kconfig index 160d12a..732a9ea 100644 --- a/src/mainboard/google/brya/Kconfig +++ b/src/mainboard/google/brya/Kconfig @@ -384,6 +384,7 @@
config BOARD_GOOGLE_SUNDANCE select BOARD_GOOGLE_BASEBOARD_NISSA + select DRIVERS_GENERIC_GPIO_KEYS
config BOARD_GOOGLE_QUANDISO select BOARD_GOOGLE_BASEBOARD_NISSA diff --git a/src/mainboard/google/brya/variants/sundance/overridetree.cb b/src/mainboard/google/brya/variants/sundance/overridetree.cb index 4f2c04a..c8d8f26 100644 --- a/src/mainboard/google/brya/variants/sundance/overridetree.cb +++ b/src/mainboard/google/brya/variants/sundance/overridetree.cb @@ -1,6 +1,346 @@ chip soc/intel/alderlake + # Acoustic settings + register "acoustic_noise_mitigation" = "1" + register "slow_slew_rate[VR_DOMAIN_IA]" = "SLEW_FAST_8" + register "slow_slew_rate[VR_DOMAIN_GT]" = "SLEW_FAST_8" + register "fast_pkg_c_ramp_disable[VR_DOMAIN_IA]" = "1" + register "fast_pkg_c_ramp_disable[VR_DOMAIN_GT]" = "1" + register "PreWake" = "100"
- device domain 0 on - end + register "sagv" = "SaGv_Enabled"
+ # EMMC Tx CMD Delay + # Refer to EDS-Vol2-42.3.7. + # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-42.3.8. + # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. + # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x909" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-42.3.9. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. + # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C2A2828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-42.3.10. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. + # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C1B4F1B" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-42.3.12. + # [17:16] stands for Rx Clock before Output Buffer, + # 00: Rx clock after output buffer, + # 01: Rx clock before output buffer, + # 10: Automatic selection based on working mode. + # 11: Reserved + # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x10023" + + # EMMC Rx Strobe Delay + # Refer to EDS-Vol2-42.3.11. + # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. + # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x11515" + + # SOC Aux orientation override: + # This is a bitfield that corresponds to up to 4 TCSS ports. + # Bits (0,1) allocated for TCSS Port1 configuration and Bits (2,3)for TCSS Port2. + # TcssAuxOri = 0101b + # Bit0,Bit2 set to "1" indicates no retimer on USBC Ports + # Bit1,Bit3 set to "0" indicates Aux lines are not swapped on the + # motherboard to USBC connector + register "tcss_aux_ori" = "5" + + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + register "typec_aux_bias_pads[1]" = "{.pad_auxp_dc = GPP_A21, .pad_auxn_dc = GPP_A22}" + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C0 + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C1 + register "usb2_ports[4]" = "USB2_PORT_MID(OC_SKIP)" # WWAN + register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # WFC Camera + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for PCIe WLAN + register "usb2_ports[9]" = "USB2_PORT_MID(OC_SKIP)" # Bluetooth port for CNVi WLAN + + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3 port for WWAN + + # Configure external V1P05/Vnn/VnnSx Rails for Sundance + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 1, + .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX & ~FIVR_ENABLE_S0, + .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, + .vnn_sx_enable_bitmap = FIVR_ENABLE_ALL_SX, + .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL, + .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_MIN_ACTIVE, + .v1p05_voltage_mv = 1050, + .vnn_voltage_mv = 780, + .vnn_sx_voltage_mv = 1050, + .v1p05_icc_max_ma = 500, + .vnn_icc_max_ma = 500, + }" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| I2C0 | TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C1 | Touchscreen | + #| I2C3 | Audio | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .early_init = 1, + .speed = I2C_SPEED_FAST_PLUS, + .speed_config[0] = { + .speed = I2C_SPEED_FAST_PLUS, + .scl_lcnt = 55, + .scl_hcnt = 30, + .sda_hold = 7, + } + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 157, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + .speed_config[0] = { + .speed = I2C_SPEED_FAST, + .scl_lcnt = 158, + .scl_hcnt = 79, + .sda_hold = 7, + } + }, + }" + + device domain 0 on + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN901C"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "280" + register "generic.stop_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""PARA3406"" + register "generic.desc" = ""Parade Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "280" + register "generic.stop_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 24 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""GTCH7503"" + register "generic.desc" = ""G2TOUCH Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.detect" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "50" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 40 on end + end + end + device ref i2c3 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + chip drivers/generic/alc1015 + register "hid" = ""RTL1019"" + register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + device generic 0 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "detect" = "1" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""SYNA0000"" + register "generic.cid" = ""ACPI0C50"" + register "generic.desc" = ""Synaptics Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.detect" = "1" + register "hid_desc_reg_offset" = "0x20" + device i2c 0x2c on end + end + end + device ref pcie_rp4 on + # PCIe 4 WLAN + register "pch_pcie_rp[PCH_RP(4)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + chip drivers/wifi/generic + register "wake" = "GPE0_DW1_03" + register "add_acpi_dma_property" = "true" + device pci 00.0 on end + end + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port2 as usb2_port + use tcss_usb3_port2 as usb3_port + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" + device ref tcss_usb3_port2 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(LEFT, LEFT, ACPI_PLD_GROUP(1, 1))" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "use_custom_pld" = "true" + register "custom_pld" = "ACPI_PLD_TYPE_C(RIGHT, LEFT, ACPI_PLD_GROUP(2, 1))" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port5 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 UFC"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 WFC"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port7 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""CNVi Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port3 on end + end + end + end + end + end end