[coreboot-gerrit] Change in coreboot[master]: soc/intel/common/block/gpio: Configure Tx Disable in IO standby for GPIs

[Furquan Shaikh (Code Review)]

Furquan Shaikh has uploaded this change for review. ( https://review.coreboot.org/29199

Change subject: soc/intel/common/block/gpio: Configure Tx Disable in IO standby for GPIs
......................................................................

soc/intel/common/block/gpio: Configure Tx Disable in IO standby for GPIs

This change updates various PAD_CFG_GPI* macros to configure Tx as
Disabled in IO Standby state. This is done to ensure that the Tx
setting is same in IO Standby state as it was in active state i.e. Tx
disabled.

BUG=b:17553222

Change-Id: If462aee3884cc61a519fb358b84867c695ace251
Signed-off-by: Furquan Shaikh 
---
M src/soc/intel/common/block/include/intelblocks/gpio_defs.h
1 file changed, 7 insertions(+), 7 deletions(-)

git pull ssh://review.coreboot.org:29418/coreboot refs/changes/99/29199/1

diff --git a/src/soc/intel/common/block/include/intelblocks/gpio_defs.h b/src/soc/intel/common/block/include/intelblocks/gpio_defs.h
index 855659a..ae6bbfc 100644
--- a/src/soc/intel/common/block/include/intelblocks/gpio_defs.h
+++ b/src/soc/intel/common/block/include/intelblocks/gpio_defs.h
@@ -196,7 +196,7 @@
 #define PAD_CFG_GPI(pad, pull, rst) \
    _PAD_CFG_STRUCT(pad,		\
    	PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE, \
-		PAD_PULL(pull) | PAD_IOSSTATE(TxLASTRxE))
+		PAD_PULL(pull) | PAD_IOSSTATE(TxDRxE))

/* General purpose input. The following macro sets the
  * Host Software Pad Ownership to GPIO Driver mode.
@@ -204,7 +204,7 @@
 #define PAD_CFG_GPI_GPIO_DRIVER(pad, pull, rst) \
    _PAD_CFG_STRUCT(pad,		\
    	PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE, \
-		PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | PAD_IOSSTATE(TxLASTRxE))
+		PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | PAD_IOSSTATE(TxDRxE))

#define PAD_CFG_GPIO_DRIVER_HI_Z(pad, pull, rst, iosstate, iosterm) \
    _PAD_CFG_STRUCT(pad,		\
@@ -224,7 +224,7 @@
    _PAD_CFG_STRUCT(pad,		\
    	PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE |	\
    		PAD_CFG0_TRIG_##trig | PAD_CFG0_RX_POL_NONE,	\
-		PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | PAD_IOSSTATE(TxLASTRxE))
+		PAD_PULL(pull) | PAD_CFG1_GPIO_DRIVER | PAD_IOSSTATE(TxDRxE))

/* No Connect configuration for unused pad.
  * NC should be GPI with Term as PU20K, PD20K, NONE depending upon default Term
@@ -263,7 +263,7 @@
    _PAD_CFG_STRUCT(pad,		\
    	PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \
    	PAD_IRQ_CFG(IOAPIC, trig, inv), PAD_PULL(pull) | \
-		PAD_IOSSTATE(TxLASTRxE))
+		PAD_IOSSTATE(TxDRxE))
 #endif

/* General purpose input, routed to APIC - with IOStandby Config*/
@@ -292,7 +292,7 @@
    _PAD_CFG_STRUCT(pad,		\
    	PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \
    	PAD_IRQ_CFG(SMI, trig, inv), PAD_PULL(pull) | \
-		PAD_IOSSTATE(TxLASTRxE))
+		PAD_IOSSTATE(TxDRxE))

/* General purpose input, routed to SMI */
 #define PAD_CFG_GPI_SMI_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \
@@ -312,7 +312,7 @@
    _PAD_CFG_STRUCT(pad,		\
    	PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \
    	PAD_IRQ_CFG(SCI, trig, inv), PAD_PULL(pull) | \
-		PAD_IOSSTATE(TxLASTRxE))
+		PAD_IOSSTATE(TxDRxE))

/* General purpose input, routed to SCI */
 #define PAD_CFG_GPI_SCI_IOS(pad, pull, rst, trig, inv, iosstate, iosterm) \
@@ -332,6 +332,6 @@
    _PAD_CFG_STRUCT(pad,		\
    	PAD_FUNC(GPIO) | PAD_RESET(rst) | PAD_CFG0_TX_DISABLE | \
    	PAD_IRQ_CFG(NMI, trig, inv), PAD_PULL(pull) | \
-		PAD_IOSSTATE(TxLASTRxE))
+		PAD_IOSSTATE(TxDRxE))

#endif /* _SOC_BLOCK_GPIO_DEFS_H_ */