[coreboot-gerrit] Change in coreboot[master]: mb/siemens/mc_apl1: do UART pad configuration at board-level

[Michael Niewöhner (Code Review)]

Michael Niewöhner has submitted this change. ( https://review.coreboot.org/c/coreboot/+/49442 )

Change subject: mb/siemens/mc_apl1: do UART pad configuration at board-level
......................................................................

mb/siemens/mc_apl1: do UART pad configuration at board-level

UART pad configuration should not be done in common code, because that
may cause short circuits, when the user sets a wrong UART index. Thus,
add the corresponding pads to the early UART gpio table for the board as
a first step. Common UART pad config code then gets dropped in CB:48829.

Also switch to `bootblock_mainboard_early_init` to configure the pads in
early bootblock before console initialization, to make the console work
as early as possible. The board does not do any other gpio configuration
in bootblock, so this should not influence behaviour in a negative way
(e.g. breaking overrides).

Change-Id: Iac8a6e386b708ae5c4dbf0677bfe05f1358bf8fd
Signed-off-by: Michael Niewöhner 
Reviewed-on: https://review.coreboot.org/c/coreboot/+/49442
Tested-by: siemens-bot
Tested-by: build bot (Jenkins) 
Reviewed-by: Mario Scheithauer 
Reviewed-by: Uwe Poeche 
Reviewed-by: Angel Pons 
---
M src/mainboard/siemens/mc_apl1/bootblock.c
M src/mainboard/siemens/mc_apl1/variants/baseboard/gpio.c
2 files changed, 4 insertions(+), 1 deletion(-)

Approvals:
  build bot (Jenkins): Verified
  siemens-bot: Verified
  Mario Scheithauer: Looks good to me, approved
  Angel Pons: Looks good to me, approved
  Uwe Poeche: Looks good to me, but someone else must approve

diff --git a/src/mainboard/siemens/mc_apl1/bootblock.c b/src/mainboard/siemens/mc_apl1/bootblock.c
index 01c8e93..a858f1b 100644
--- a/src/mainboard/siemens/mc_apl1/bootblock.c
+++ b/src/mainboard/siemens/mc_apl1/bootblock.c
@@ -4,7 +4,7 @@
 #include <bootblock_common.h>
 #include <intelblocks/gpio.h>

-void bootblock_mainboard_init(void)
+void bootblock_mainboard_early_init(void)
 {
    const struct pad_config *pads;
    size_t num;
diff --git a/src/mainboard/siemens/mc_apl1/variants/baseboard/gpio.c b/src/mainboard/siemens/mc_apl1/variants/baseboard/gpio.c
index 2edd92e..6a3b859 100644
--- a/src/mainboard/siemens/mc_apl1/variants/baseboard/gpio.c
+++ b/src/mainboard/siemens/mc_apl1/variants/baseboard/gpio.c
@@ -356,6 +356,9 @@

/* GPIOs needed prior to ramstage. */
 static const struct pad_config early_gpio_table[] = {
+	/* UART */
+	PAD_CFG_NF(GPIO_46, NATIVE, DEEP, NF1),				/* LPSS_UART2_RXD */
+	PAD_CFG_NF_IOSSTATE(GPIO_47, NATIVE, DEEP, NF1, Tx1RxDCRx0),	/* LPSS_UART2_TXD */

/* Debug tracing. */
    PAD_CFG_GPI(GPIO_0, DN_20K, DEEP),	/* TRACE_0_CLK_VNN */