Fabian Kunkel (fabi@adv.bruhnspace.com) just uploaded a new patch set to gerrit, which you can find at http://review.coreboot.org/10288
-gerrit
commit 1d9c7c5da78f7c3680c2a30093dab0883b3881dd Author: Fabian Kunkel fabi@adv.bruhnspace.com Date: Mon May 25 17:08:17 2015 +0200
mainboard/bap: Add support for BAP ODE E20XX
Adding new board based on AMD Kabini. Most of the code is copied from gizmosphere/gizmo2 Board is developed by BAP - Bruhnspace Advanced Projects: http://www.unibap.com/ (Site is under construction) Special on this board is: -Soldered down memory -SuperIO Fintek F81866D Known bugs: -S3 doesnt work -Serial ports only works for the first boot. Needs power cut. Tested with: -SeaBios as Payload -Linux OS - Lubuntu 14.10 32/64Bit, Kernel 3.19 - 4.1 -Windows 8 64Bit
Change-Id: I7e2b306620dd152a9f01ab6ccf2a0a880a068adb Signed-off-by: Fabian Kunkel fabi@adv.bruhnspace.com --- src/mainboard/bap/Kconfig | 24 +- src/mainboard/bap/ode_e20XX/BAP_Q7.spd.hex | 283 +++++++++++++++++++++ src/mainboard/bap/ode_e20XX/Kconfig | 1 + src/mainboard/bap/ode_e20XX/Makefile.inc | 2 +- .../bap/ode_e20XX/Micron_MT41J128M16JT.spd.hex | 235 ----------------- src/mainboard/bap/ode_e20XX/PlatformGnbPcie.c | 26 +- src/mainboard/bap/ode_e20XX/acpi/superio.asl | 34 ++- src/mainboard/bap/ode_e20XX/devicetree.cb | 67 ++++- src/mainboard/bap/ode_e20XX/romstage.c | 14 +- 9 files changed, 419 insertions(+), 267 deletions(-)
diff --git a/src/mainboard/bap/Kconfig b/src/mainboard/bap/Kconfig index 17b85bf..d72f131 100644 --- a/src/mainboard/bap/Kconfig +++ b/src/mainboard/bap/Kconfig @@ -1,13 +1,33 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2015 BAP - Bruhnspace Advanced Projects +## (Written by Fabian Kunkel fabi@adv.bruhnspace.com for BAP) +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; version 2 of the License. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc. +## if VENDOR_BAP
choice prompt "Mainboard model"
-source "src/mainboard/bap/*/Kconfig.name" +config BOARD_ODE_E20XX + bool "ODE_E20XX"
endchoice
-source "src/mainboard/bap/*/Kconfig" +source "src/mainboard/bap/ode_e20XX/Kconfig"
config MAINBOARD_VENDOR string diff --git a/src/mainboard/bap/ode_e20XX/BAP_Q7.spd.hex b/src/mainboard/bap/ode_e20XX/BAP_Q7.spd.hex new file mode 100644 index 0000000..e2558ba --- /dev/null +++ b/src/mainboard/bap/ode_e20XX/BAP_Q7.spd.hex @@ -0,0 +1,283 @@ +## +## This file is part of the coreboot project. +## +## Copyright (C) 2014 Sage Electronic Engineering, LLC. +## Copyright (C) 2015 BAP - Bruhnspace Advanced Projects +## (Written by Fabian Kunkel fabi@adv.bruhnspace.com for BAP) +## +## This program is free software; you can redistribute it and/or modify +## it under the terms of the GNU General Public License as published by +## the Free Software Foundation; either version 2 of the License. +## +## This program is distributed in the hope that it will be useful, +## but WITHOUT ANY WARRANTY; without even the implied warranty of +## MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +## GNU General Public License for more details. +## +## You should have received a copy of the GNU General Public License +## along with this program; if not, write to the Free Software +## Foundation, Inc. +## + +# BAP ODE E20XX has 2GB ram soldered down on the Q7 + +# 0 Number of SPD Bytes used / Total SPD Size / CRC Coverage +# bits[3:0]: 1 = 128 SPD Bytes Used +# bits[6:4]: 1 = 256 SPD Bytes Total +# bit7 : 0 = CRC covers bytes 0 ~ 125 +92 + +# 1 SPD Revision - +# 0x10 = Revision 1.0 +12 + +# 2 Key Byte / DRAM Device Type +# bits[7:0]: 0x0b = DDR3 SDRAM +0B + +# 3 Key Byte / Module Type +# bits[3:0]: 3 = SO-DIMM +# bits[7:4]: reserved +03 + +# 4 SDRAM CHIP Density and Banks +# bits[3:0]: 3 = 2 Gigabits Total SDRAM capacity per chip +# bits[6:4]: 0 = 3 (8 banks) +# bit7 : reserved +04 + +# 5 SDRAM Addressing +# bits[2:0]: 1 = 10 Column Address Bits +# bits[5:3]: 2 = 14 Row Address Bits +# bits[7:6]: reserved +19 + +# 6 Module Nominal Voltage, VDD +# bit0 : 0 = 1.5 V operable +# bit1 : 0 = NOT 1.35 V operable +# bit2 : 0 = NOT 1.25 V operable +# bits[7:3]: reserved +00 + +# 7 Module Organization +# bits[2:0]: 2 = 16 bits +# bits[5:3]: 0 = 1 Rank +# bits[7:6]: reserved +02 + +# 8 Module Memory Bus Width +# bits[2:0]: 3 = Primary bus width is 64 bits +# bits[4:3]: 0 = 0 bits (no bus width extension) +# bits[7:5]: reserved +08 + +# 9 Fine Timebase (FTB) Dividend / Divisor +# bits[3:0]: 0x02 divisor +# bits[7:4]: 0x05 dividend +# 5/2 = 2.5ps +52 + +# 10 Medium Timebase (MTB) Dividend +# 11 Medium Timebase (MTB) Divisor +# 1 / 8 = .125 ns - used for clock freq of 400 through 1066 MHz +01 08 + +# 12 SDRAM Minimum Cycle Time (tCKmin) +# 0x0a = tCKmin of 1.25 ns = DDR3-1600 (800 MHz clock) +0C + +# 13 Reserved +00 + +# 14 CAS Latencies Supported, Least Significant Byte +# 15 CAS Latencies Supported, Most Significant Byte +# Cas Latencies of 11 - 5 are supported +7E 00 + +# 16 Minimum CAS Latency Time (tAAmin) +# 0x6E = 13.75ns - DDR3-1600K +69 + +# 17 Minimum Write Recovery Time (tWRmin) +# 0x78 = tWR of 15ns - All DDR3 speed grades +78 + +# 18 Minimum RAS# to CAS# Delay Time (tRCDmin) +# 0x6E = 13.75ns - DDR3-1600K +69 + +# 19 Minimum Row Active to Row Active Delay Time (tRRDmin) +# 0x3C = 7.5ns +3C + +# 20 Minimum Row Precharge Delay Time (tRPmin) +# 0x6E = 13.75ns - DDR3-1600K +69 + +# 21 Upper Nibbles for tRAS and tRC +# bits[3:0]: tRAS most significant nibble = 1 (see byte 22) +# bits[7:4]: tRC most significant nibble = 1 (see byte 23) +11 + +# 22 Minimum Active to Precharge Delay Time (tRASmin), LSB +# 0x118 = 35ns - DDR3-1600 (see byte 21) +20 + +# 23 Minimum Active to Active/Refresh Delay Time (tRCmin), LSB +# 0x186 = 48.75ns - DDR3-1600K +89 + +# 24 Minimum Refresh Recovery Delay Time (tRFCmin), LSB +# 25 Minimum Refresh Recovery Delay Time (tRFCmin), MSB +# 0x500 = 160ns - for 2 Gigabit chips +20 08 + +# 26 Minimum Internal Write to Read Command Delay Time (tWTRmin) +# 0x3c = 7.5 ns - All DDR3 SDRAM speed bins +3C + +# 27 Minimum Internal Read to Precharge Command Delay Time (tRTPmin) +# 0x3c = 7.5ns - All DDR3 SDRAM speed bins +3C + +# 28 Upper Nibble for tFAWmin +# 29 Minimum Four Activate Window Delay Time (tFAWmin) +# 0x0140 = 40ns - DDR3-1600, 2 KB page size +01 68 + +# 30 SDRAM Optional Feature +# bit0 : 1= RZQ/6 supported +# bit1 : 1 = RZQ/7 supported +# bits[6:2]: reserved +# bit7 : 1 = DLL Off mode supported +83 + +# 31 SDRAM Thermal and Refresh Options +# bit0 : 1 = Temp up to 95c supported +# bit1 : 0 = 85-95c uses 2x refresh rate +# bit2 : 1 = Auto Self Refresh supported +# bit3 : 0 = no on die thermal sensor +# bits[6:4]: reserved +# bit7 : 0 = partial self refresh supported +01 + +# 32 Module Thermal Sensor +# 0 = Thermal sensor not incorporated onto this assembly +00 + +# 33 SDRAM Device Type +# bits[1:0]: 0 = Signal Loading not specified +# bits[3:2]: reserved +# bits[6:4]: 0 = Die count not specified +# bit7 : 0 = Standard Monolithic DRAM Device +00 + +# 34 Fine Offset for SDRAM Minimum Cycle Time (tCKmin) +# 35 Fine Offset for Minimum CAS Latency Time (tAAmin) +# 36 Fine Offset for Minimum RAS# to CAS# Delay Time (tRCDmin) +# 37 Fine Offset for Minimum Row Precharge Delay Time (tRPmin) +# 38 Fine Offset for Minimum Active to Active/Refresh Delay (tRCmin) +00 00 00 00 00 + +# 39 - 59 (reserved) +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 + +# 60 Raw Card Extension, Module Nominal Height +# bits[4:0]: 0 = <= 15mm tall +# bits[7:5]: 0 = raw card revision 0-3 +0f + +# 61 Module Maximum Thickness +# bits[3:0]: 0 = thickness front <= 1mm +# bits[7:4]: 0 = thinkness back <= 1mm +11 + +# 62 Reference Raw Card Used +# bits[4:0]: 0 = Reference Raw card A used +# bits[6:5]: 0 = revision 0 +# bit7 : 0 = Reference raw cards A through AL +22 + +# 63 Address Mapping from Edge Connector to DRAM +# bit0 : 0 = standard mapping (not mirrored) +# bits[7:1]: reserved +00 + +# 64 - 116 (reserved) +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 00 00 00 +00 00 00 00 00 + +# 117 - 118 Module ID: Module Manufacturers JEDEC ID Code +# 0x0001 = AMD +80 AD + +# 119 Module ID: Module Manufacturing Location - oem specified +# 120 Module ID: Module Manufacture Year in BCD +# 0x13 = 2013 +01 00 + +# 121 Module ID: Module Manufacture week +# 0x12 = 12th week +00 + +# 122 - 125: Module Serial Number +00 00 00 00 + +# 126 - 127: Cyclical Redundancy Code +D4 51 + +# Coreboot is only interested in the first 128 values +#128 - 135 +48 4d 54 34 32 35 53 36 + +#136 - 143 +4d 46 52 36 43 2d 48 39 + +#144 - 151 +20 20 4e 30 80 ad 00 00 + +#152 - 159 +00 00 00 00 00 00 00 00 + +#160 - 167 +00 00 00 00 00 00 00 00 + +#168 - 175 +00 00 00 00 00 00 00 00 + +#176 - 183 +00 00 00 00 00 00 00 00 + +#184 - 191 +00 00 00 00 00 00 00 00 + +#192 - 199 +00 00 00 00 00 00 00 00 + +#200 - 207 +00 00 00 00 00 00 00 00 + +#208 - 215 +00 00 00 00 00 00 00 00 + +#216 - 223 +00 00 00 00 00 00 00 00 + +#224 - 231 +00 00 00 00 00 00 00 00 + +#232 - 239 +00 00 00 00 00 00 00 00 + +#240 - 247 +00 00 00 00 00 00 00 00 + +#248 - 255 +00 00 00 00 00 00 00 00 \ No newline at end of file diff --git a/src/mainboard/bap/ode_e20XX/Kconfig b/src/mainboard/bap/ode_e20XX/Kconfig index 94ad97b..15face5 100644 --- a/src/mainboard/bap/ode_e20XX/Kconfig +++ b/src/mainboard/bap/ode_e20XX/Kconfig @@ -31,6 +31,7 @@ config BOARD_SPECIFIC_OPTIONS # dummy select HAVE_ACPI_TABLES select BOARD_ROMSIZE_KB_4096 select GFXUMA + select SUPERIO_FINTEK_F81866D select SPD_CACHE
config MAINBOARD_DIR diff --git a/src/mainboard/bap/ode_e20XX/Makefile.inc b/src/mainboard/bap/ode_e20XX/Makefile.inc index 6bbb85a..13523dd 100644 --- a/src/mainboard/bap/ode_e20XX/Makefile.inc +++ b/src/mainboard/bap/ode_e20XX/Makefile.inc @@ -30,7 +30,7 @@ ramstage-y += PlatformGnbPcie.c SPD_BIN = $(obj)/spd.bin
# Order of names in SPD_SOURCES is important! -SPD_SOURCES = Micron_MT41J128M16JT +SPD_SOURCES = BAP_Q7
SPD_DEPS := $(foreach f, $(SPD_SOURCES), src/mainboard/$(MAINBOARDDIR)/$(f).spd.hex)
diff --git a/src/mainboard/bap/ode_e20XX/Micron_MT41J128M16JT.spd.hex b/src/mainboard/bap/ode_e20XX/Micron_MT41J128M16JT.spd.hex deleted file mode 100644 index 08736f6..0000000 --- a/src/mainboard/bap/ode_e20XX/Micron_MT41J128M16JT.spd.hex +++ /dev/null @@ -1,235 +0,0 @@ -# -# This file is part of the coreboot project. -# -# Copyright (C) 2014 Sage Electronic Engineering, LLC. -# -# This program is free software; you can redistribute it and/or modify -# it under the terms of the GNU General Public License as published by -# the Free Software Foundation; version 2 of the License. -# -# This program is distributed in the hope that it will be useful, -# but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the -# GNU General Public License for more details. -# -# You should have received a copy of the GNU General Public License -# along with this program; if not, write to the Free Software -# Foundation, Inc. - -# Gizmo2 has 1GB using 4 Micron_MT41J128M16JT-125 chips -# The datasheet is available at: -# http://download.micron.com/pdf/datasheets/dram/ddr3/2Gb_DDR3_SDRAM.pdf - -# SPD contents for Gizmo2 2GB DDR3 (1600MHz PC3-12800) soldered down - -# 0 Number of SPD Bytes used / Total SPD Size / CRC Coverage -# bits[3:0]: 1 = 128 SPD Bytes Used -# bits[6:4]: 1 = 256 SPD Bytes Total -# bit7 : 0 = CRC covers bytes 0 ~ 125 -11 - -# 1 SPD Revision - -# 0x10 = Revision 1.0 -10 - -# 2 Key Byte / DRAM Device Type -# bits[7:0]: 0x0b = DDR3 SDRAM -0B - -# 3 Key Byte / Module Type -# bits[3:0]: 3 = SO-DIMM -# bits[7:4]: reserved -03 - -# 4 SDRAM CHIP Density and Banks -# bits[3:0]: 3 = 2 Gigabits Total SDRAM capacity per chip -# bits[6:4]: 0 = 3 (8 banks) -# bit7 : reserved -03 - -# 5 SDRAM Addressing -# bits[2:0]: 1 = 10 Column Address Bits -# bits[5:3]: 2 = 14 Row Address Bits -# bits[7:6]: reserved -11 - -# 6 Module Nominal Voltage, VDD -# bit0 : 0 = 1.5 V operable -# bit1 : 0 = NOT 1.35 V operable -# bit2 : 0 = NOT 1.25 V operable -# bits[7:3]: reserved -00 - -# 7 Module Organization -# bits[2:0]: 2 = 16 bits -# bits[5:3]: 0 = 1 Rank -# bits[7:6]: reserved -02 - -# 8 Module Memory Bus Width -# bits[2:0]: 3 = Primary bus width is 64 bits -# bits[4:3]: 0 = 0 bits (no bus width extension) -# bits[7:5]: reserved -03 - -# 9 Fine Timebase (FTB) Dividend / Divisor -# bits[3:0]: 0x02 divisor -# bits[7:4]: 0x05 dividend -# 5/2 = 2.5ps -52 - -# 10 Medium Timebase (MTB) Dividend -# 11 Medium Timebase (MTB) Divisor -# 1 / 8 = .125 ns - used for clock freq of 400 through 1066 MHz -01 08 - -# 12 SDRAM Minimum Cycle Time (tCKmin) -# 0x0a = tCKmin of 1.25 ns = DDR3-1600 (800 MHz clock) -0A - -# 13 Reserved -00 - -# 14 CAS Latencies Supported, Least Significant Byte -# 15 CAS Latencies Supported, Most Significant Byte -# Cas Latencies of 11 - 5 are supported -FE 00 - -# 16 Minimum CAS Latency Time (tAAmin) -# 0x6E = 13.75ns - DDR3-1600K -6E - -# 17 Minimum Write Recovery Time (tWRmin) -# 0x78 = tWR of 15ns - All DDR3 speed grades -78 - -# 18 Minimum RAS# to CAS# Delay Time (tRCDmin) -# 0x6E = 13.75ns - DDR3-1600K -6E - -# 19 Minimum Row Active to Row Active Delay Time (tRRDmin) -# 0x3C = 7.5ns -3C - -# 20 Minimum Row Precharge Delay Time (tRPmin) -# 0x6E = 13.75ns - DDR3-1600K -6E - -# 21 Upper Nibbles for tRAS and tRC -# bits[3:0]: tRAS most significant nibble = 1 (see byte 22) -# bits[7:4]: tRC most significant nibble = 1 (see byte 23) -11 - -# 22 Minimum Active to Precharge Delay Time (tRASmin), LSB -# 0x118 = 35ns - DDR3-1600 (see byte 21) -18 - -# 23 Minimum Active to Active/Refresh Delay Time (tRCmin), LSB -# 0x186 = 48.75ns - DDR3-1600K -86 - -# 24 Minimum Refresh Recovery Delay Time (tRFCmin), LSB -# 25 Minimum Refresh Recovery Delay Time (tRFCmin), MSB -# 0x500 = 160ns - for 2 Gigabit chips -00 05 - -# 26 Minimum Internal Write to Read Command Delay Time (tWTRmin) -# 0x3c = 7.5 ns - All DDR3 SDRAM speed bins -3C - -# 27 Minimum Internal Read to Precharge Command Delay Time (tRTPmin) -# 0x3c = 7.5ns - All DDR3 SDRAM speed bins -3C - -# 28 Upper Nibble for tFAWmin -# 29 Minimum Four Activate Window Delay Time (tFAWmin) -# 0x0140 = 40ns - DDR3-1600, 2 KB page size -01 40 - -# 30 SDRAM Optional Feature -# bit0 : 1= RZQ/6 supported -# bit1 : 1 = RZQ/7 supported -# bits[6:2]: reserved -# bit7 : 1 = DLL Off mode supported -83 - -# 31 SDRAM Thermal and Refresh Options -# bit0 : 1 = Temp up to 95c supported -# bit1 : 0 = 85-95c uses 2x refresh rate -# bit2 : 1 = Auto Self Refresh supported -# bit3 : 0 = no on die thermal sensor -# bits[6:4]: reserved -# bit7 : 0 = partial self refresh supported -05 - -# 32 Module Thermal Sensor -# 0 = Thermal sensor not incorporated onto this assembly -00 - -# 33 SDRAM Device Type -# bits[1:0]: 0 = Signal Loading not specified -# bits[3:2]: reserved -# bits[6:4]: 0 = Die count not specified -# bit7 : 0 = Standard Monolithic DRAM Device -00 - -# 34 Fine Offset for SDRAM Minimum Cycle Time (tCKmin) -# 35 Fine Offset for Minimum CAS Latency Time (tAAmin) -# 36 Fine Offset for Minimum RAS# to CAS# Delay Time (tRCDmin) -# 37 Fine Offset for Minimum Row Precharge Delay Time (tRPmin) -# 38 Fine Offset for Minimum Active to Active/Refresh Delay (tRCmin) -00 00 00 00 00 - -# 39 - 59 (reserved) -00 00 00 00 00 00 00 00 -00 00 00 00 00 00 00 00 -00 00 00 00 00 - -# 60 Raw Card Extension, Module Nominal Height -# bits[4:0]: 0 = <= 15mm tall -# bits[7:5]: 0 = raw card revision 0-3 -00 - -# 61 Module Maximum Thickness -# bits[3:0]: 0 = thickness front <= 1mm -# bits[7:4]: 0 = thinkness back <= 1mm -00 - -# 62 Reference Raw Card Used -# bits[4:0]: 0 = Reference Raw card A used -# bits[6:5]: 0 = revision 0 -# bit7 : 0 = Reference raw cards A through AL -00 - -# 63 Address Mapping from Edge Connector to DRAM -# bit0 : 0 = standard mapping (not mirrored) -# bits[7:1]: reserved -00 - -# 64 - 116 (reserved) -00 00 00 00 00 00 00 00 -00 00 00 00 00 00 00 00 -00 00 00 00 00 00 00 00 -00 00 00 00 00 00 00 00 -00 00 00 00 00 00 00 00 -00 00 00 00 00 00 00 00 -00 00 00 00 00 - -# 117 - 118 Module ID: Module Manufacturers JEDEC ID Code -# 0x0001 = AMD -00 01 - -# 119 Module ID: Module Manufacturing Location - oem specified -# 120 Module ID: Module Manufacture Year in BCD -# 0x13 = 2013 -00 13 - -# 121 Module ID: Module Manufacture week -# 0x12 = 12th week -12 - -# 122 - 125: Module Serial Number -53 41 47 45 - -# 126 - 127: Cyclical Redundancy Code -00 00 diff --git a/src/mainboard/bap/ode_e20XX/PlatformGnbPcie.c b/src/mainboard/bap/ode_e20XX/PlatformGnbPcie.c index 66bebc2..8a49af5 100644 --- a/src/mainboard/bap/ode_e20XX/PlatformGnbPcie.c +++ b/src/mainboard/bap/ode_e20XX/PlatformGnbPcie.c @@ -32,20 +32,20 @@ static const PCIe_PORT_DESCRIPTOR PortList [] = { 0, PCIE_ENGINE_DATA_INITIALIZER (PciePortEngine, 3, 3), PCIE_PORT_DATA_INITIALIZER_V2 (PortEnabled, ChannelTypeExt6db, 2, 5, - HotplugDisabled, + HotplugBasic, PcieGenMaxSupported, PcieGenMaxSupported, - AspmDisabled, 0x01, 0) + AspmL0sL1, 0x01, 0) }, /* Initialize Port descriptor (PCIe port, Lanes 1, PCI Device Number 2, ...) */ { 0, PCIE_ENGINE_DATA_INITIALIZER (PciePortEngine, 2, 2), PCIE_PORT_DATA_INITIALIZER_V2 (PortEnabled, ChannelTypeExt6db, 2, 4, - HotplugDisabled, + HotplugBasic, PcieGenMaxSupported, PcieGenMaxSupported, - AspmDisabled, 0x02, 0) + AspmL0sL1, 0x02, 0) }, /* Initialize Port descriptor (PCIe port, Lanes 2, PCI Device Number 2, ...) */ { @@ -55,7 +55,7 @@ static const PCIe_PORT_DESCRIPTOR PortList [] = { HotplugDisabled, PcieGenMaxSupported, PcieGenMaxSupported, - AspmDisabled, 0x03, 0) + AspmL0sL1, 0x03, 0) }, /* Initialize Port descriptor (PCIe port, Lanes 3, PCI Device Number 2, ...) */ { @@ -65,32 +65,32 @@ static const PCIe_PORT_DESCRIPTOR PortList [] = { HotplugDisabled, PcieGenMaxSupported, PcieGenMaxSupported, - AspmDisabled, 0x04, 0) + AspmL0sL1, 0x04, 0) }, /* Initialize Port descriptor (PCIe port, Lanes 4-7, PCI Device Number 4, ...) */ { - DESCRIPTOR_TERMINATE_LIST, + DESCRIPTOR_TERMINATE_LIST, //Descriptor flags !!!IMPORTANT!!! Terminate last element of array PCIE_ENGINE_DATA_INITIALIZER (PciePortEngine, 4, 7), PCIE_PORT_DATA_INITIALIZER_V2 (PortEnabled, ChannelTypeExt6db, 2, 1, - HotplugDisabled, + HotplugBasic, PcieGenMaxSupported, PcieGenMaxSupported, - AspmDisabled, 0x05, 0) + AspmL0sL1, 0x05, 0) } };
static const PCIe_DDI_DESCRIPTOR DdiList [] = { - /* DP0 to HDMI0/DP */ + /* DP0 to LVDS*/ { 0, PCIE_ENGINE_DATA_INITIALIZER (PcieDdiEngine, 8, 11), - PCIE_DDI_DATA_INITIALIZER (ConnectorTypeHDMI, Aux1, Hdp1) + PCIE_DDI_DATA_INITIALIZER (ConnectorTypeDP, Aux1, Hdp1) }, - /* DP1 to high-speed edge connector */ + /* DP1 to HDMI */ { DESCRIPTOR_TERMINATE_LIST, PCIE_ENGINE_DATA_INITIALIZER (PcieDdiEngine, 12, 15), - PCIE_DDI_DATA_INITIALIZER (ConnectorTypeDP, Aux2, Hdp2) + PCIE_DDI_DATA_INITIALIZER (ConnectorTypeHDMI, Aux2, Hdp2) }, };
diff --git a/src/mainboard/bap/ode_e20XX/acpi/superio.asl b/src/mainboard/bap/ode_e20XX/acpi/superio.asl index 97304f9..1c5b3cd 100644 --- a/src/mainboard/bap/ode_e20XX/acpi/superio.asl +++ b/src/mainboard/bap/ode_e20XX/acpi/superio.asl @@ -2,6 +2,8 @@ * This file is part of the coreboot project. * * Copyright (C) 2013 Sage Electronic Engineering, LLC + * Copyright (C) 2015 BAP - Bruhnspace Advanced Projects + * (Written by Fabian Kunkel fabi@adv.bruhnspace.com for BAP) * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -17,4 +19,34 @@ * Foundation, Inc. */
-/* No Super I/O device or functionality yet */ +/* SuperIO support for Windows */ + +Device (UAR1) { + Name (_HID, EISAID ("PNP0501")) + Name (_UID, 1) + Name (_CRS, ResourceTemplate () + { + IO (Decode16, 0x03F8, 0x03F8, 0x08, 0x08) + IRQNoFlags () {4} + }) + Name (_PRS, ResourceTemplate () + { + IO (Decode16, 0x03F8, 0x03F8, 0x08, 0x08) + IRQNoFlags () {4} + }) +} + +Device (UAR2) { + Name (_HID, EISAID ("PNP0501")) + Name (_UID, 2) + Name (_CRS, ResourceTemplate () + { + IO (Decode16, 0x02F8, 0x02F8, 0x08, 0x08) + IRQNoFlags () {3} + }) + Name (_PRS, ResourceTemplate () + { + IO (Decode16, 0x02F8, 0x02F8, 0x08, 0x08) + IRQNoFlags () {3} + }) +} diff --git a/src/mainboard/bap/ode_e20XX/devicetree.cb b/src/mainboard/bap/ode_e20XX/devicetree.cb index 34c2fd4..93f5e73 100644 --- a/src/mainboard/bap/ode_e20XX/devicetree.cb +++ b/src/mainboard/bap/ode_e20XX/devicetree.cb @@ -9,7 +9,7 @@ # # This program is distributed in the hope that it will be useful, # but WITHOUT ANY WARRANTY; without even the implied warranty of -# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the # GNU General Public License for more details. # # You should have received a copy of the GNU General Public License @@ -32,11 +32,11 @@ chip northbridge/amd/agesa/family16kb/root_complex device pci 1.0 on end # Internal Graphics P2P bridge 0x9835 device pci 1.1 on end # Internal Multimedia device pci 2.0 on end # PCIe Host Bridge - device pci 2.1 on end # PCIe GFX Bridge - device pci 2.2 on end # PCIe GPP mini PCIe - device pci 2.3 on end # PCIe LAN - device pci 2.4 on end # PCIe x2 to high speed edge connector - device pci 2.5 on end # PCIe x2 to high speed edge connector + device pci 2.1 on end # x4 PCIe Slot + device pci 2.2 on end # PCIe Q7 Realtek GBit LAN + device pci 2.3 on end # PCIe CB Realtek GBit LAN + device pci 2.4 on end # PCIe BAP FPGA + device pci 2.5 on end # PCIe BAP FPGA (unused, for 050T) end #chip northbridge/amd/agesa/family16kb
chip southbridge/amd/agesa/hudson # it is under NB/SB Link, but on the same pci bus @@ -48,7 +48,60 @@ chip northbridge/amd/agesa/family16kb/root_complex device pci 13.2 on end # USB device pci 14.0 on end # SM device pci 14.2 on end # HDA 0x4383 - device pci 14.3 on end # LPC 0x439d + device pci 14.3 on # LPC 0x439d + chip superio/fintek/f81866d + register "hwm_amd_tsi_addr" = "0x98" # Set to AMD + register "hwm_amd_tsi_control" = "0x02" # Set to AMD + register "hwm_fan_select" = "0xC0" # Sets Fan2 to PWM + register "hwm_fan_mode" = "0xD5" # Sets FAN1-3 to Auto RPM mode + register "hwm_fan3_control" = "0x00" # Fan control 23kHz + register "hwm_fan2_temp_map_select" = "0x1E" # Fan control 23kHz + register "hwm_fan2_bound1" = "0x3C" # 60°C + register "hwm_fan2_bound2" = "0x32" # 50°C + register "hwm_fan2_bound3" = "0x28" # 40°C + register "hwm_fan2_bound4" = "0x1E" # 30°C + register "hwm_fan2_seg1_speed" = "0xFF" # 100% + register "hwm_fan2_seg2_speed" = "0xD9" # 85% + register "hwm_fan2_seg3_speed" = "0xB2" # 70% + register "hwm_fan2_seg4_speed" = "0x99" # 60% + register "hwm_fan2_seg5_speed" = "0x80" # 50% + register "hwm_temp_sens_type" = "0x04" # Sets temp sensor 1 type to to thermistor + device pnp 4e.0 off # Floppy + io 0x60 = 0x3f0 + irq 0x70 = 6 + drq 0x74 = 2 + end + device pnp 4e.3 off end # Parallel Port + device pnp 4e.4 on # Hardware Monitor + io 0x60 = 0x295 + irq 0x70 = 0 + end + device pnp 4e.5 off # Keyboard + io 0x60 = 0x60 + io 0x62 = 0x64 + irq 0x70 = 1 + end + device pnp 4e.6 off end # GPIO + device pnp 4e.7 on end # WDT + device pnp 4e.a off end # PME + device pnp 4e.10 on # COM1 + io 0x60 = 0x3f8 + irq 0x70 = 4 + end + device pnp 4e.11 on # COM2 + io 0x60 = 0x2f8 + irq 0x70 = 3 + end + device pnp 4e.12 off # COM3 + end + device pnp 4e.13 off # COM4 + end + device pnp 4e.14 off # COM5 + end + device pnp 4e.15 off # COM6 + end + end # f81866d + end #LPC device pci 14.7 on end # SD end #chip southbridge/amd/hudson
diff --git a/src/mainboard/bap/ode_e20XX/romstage.c b/src/mainboard/bap/ode_e20XX/romstage.c index 4cfca8e..2c2c4f1 100644 --- a/src/mainboard/bap/ode_e20XX/romstage.c +++ b/src/mainboard/bap/ode_e20XX/romstage.c @@ -2,6 +2,8 @@ * This file is part of the coreboot project. * * Copyright (C) 2012 Advanced Micro Devices, Inc. + * Copyright (C) 2015 BAP - Bruhnspace Advanced Projects + * (Written by Fabian Kunkel fabi@adv.bruhnspace.com for BAP) * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by @@ -35,21 +37,16 @@ #include <cpu/x86/lapic.h> #include <southbridge/amd/agesa/hudson/hudson.h> #include <cpu/amd/agesa/s3_resume.h> +#include <superio/fintek/common/fintek.h> +#include <superio/fintek/f81866d/f81866d.h> #include "cbmem.h"
+#define SERIAL_DEV1 PNP_DEV(0x4e, F81866D_SP1)
void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) { u32 val;
- /* In Hudson RRG, PMIOxD2[5:4] is "Drive strength control for - * LpcClk[1:0]". To be consistent with Parmer, setting to 4mA - * even though the register is not documented in the Kabini BKDG. - * Otherwise the serial output is bad code. - */ - outb(0xD2, 0xcd6); - outb(0x00, 0xcd7); - amd_initmmio();
/* Set LPC decode enables. */ @@ -62,6 +59,7 @@ void cache_as_ram_main(unsigned long bist, unsigned long cpu_init_detectedx) post_code(0x30);
post_code(0x31); + fintek_enable_serial(SERIAL_DEV1, CONFIG_TTYS0_BASE); console_init(); }
-
Fabian Kunkel