Edward O'Callaghan has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/42675 )
Change subject: util/mb/google/tmpl/puff: Import overridetree.cb copy ......................................................................
util/mb/google/tmpl/puff: Import overridetree.cb copy
BUG=b:154071868 BRANCH=none TEST=none
Change-Id: I40faa5f80e78cd73ba5ef977574f7f662c0ab8a1 Signed-off-by: Edward O'Callaghan quasisec@google.com --- M util/mainboard/google/puff/template/overridetree.cb 1 file changed, 400 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/75/42675/1
diff --git a/util/mainboard/google/puff/template/overridetree.cb b/util/mainboard/google/puff/template/overridetree.cb index abbcaaa..ededac4 100644 --- a/util/mainboard/google/puff/template/overridetree.cb +++ b/util/mainboard/google/puff/template/overridetree.cb @@ -1,6 +1,406 @@ chip soc/intel/cannonlake + # Enable heci communication + register "HeciEnabled" = "1" + + # Auto-switch between X4 NVMe and X2 NVMe. + register "TetonGlacierMode" = "1" + + register "SerialIoDevMode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoDisabled, + [PchSerialIoIndexI2C1] = PchSerialIoDisabled, + [PchSerialIoIndexI2C2] = PchSerialIoPci, + [PchSerialIoIndexI2C3] = PchSerialIoPci, + [PchSerialIoIndexI2C4] = PchSerialIoPci, + [PchSerialIoIndexI2C5] = PchSerialIoPci, + [PchSerialIoIndexSPI0] = PchSerialIoPci, + [PchSerialIoIndexSPI1] = PchSerialIoPci, + [PchSerialIoIndexSPI2] = PchSerialIoDisabled, + [PchSerialIoIndexUART0] = PchSerialIoSkipInit, + [PchSerialIoIndexUART1] = PchSerialIoDisabled, + [PchSerialIoIndexUART2] = PchSerialIoDisabled, + }" + + # USB configuration + # NOTE: This only applies to Puff, + # usb2_ports[1] and usb2_ports[3] were swapped on + # reference schematics after Puff has been built. + register "usb2_ports[0]" = "{ + .enable = 1, + .ocpin = OC2, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_11P25MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 2 + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port + register "usb2_ports[2]" = "{ + .enable = 1, + .ocpin = OC3, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 3 + register "usb2_ports[3]" = "{ + .enable = 1, + .ocpin = OC1, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 1 + register "usb2_ports[4]" = "{ + .enable = 1, + .ocpin = OC_SKIP, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 4 + register "usb2_ports[5]" = "{ + .enable = 1, + .ocpin = OC0, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A port 0 + register "usb2_ports[6]" = "USB2_PORT_EMPTY" + register "usb2_ports[7]" = "USB2_PORT_EMPTY" + register "usb2_ports[8]" = "USB2_PORT_EMPTY" + register "usb2_ports[9]" = "{ + .enable = 1, + .ocpin = OC_SKIP, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # BT + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port 2 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port 3 + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port 1 + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C + register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port 0 + register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Port 4 + + # Enable eMMC HS400 + register "ScsEmmcHs400Enabled" = "1" + + # EMMC Tx CMD Delay + # Refer to EDS-Vol2-14.3.7. + # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-14.3.8. + # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. + # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x911" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-14.3.9. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. + # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C262828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-14.3.10. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. + # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C16583b" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-14.3.12. + # [17:16] stands for Rx Clock before Output Buffer, + # 00: Rx clock after output buffer, + # 01: Rx clock before output buffer, + # 10: Automatic selection based on working mode. + # 11: Reserved + # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1001D" + + # EMMC Rx Strobe Delay + # Refer to EDS-Vol2-14.3.11. + # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. + # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1515" + + # Intel HDA - disable I2S Audio SSP1 and DMIC0 as puff variant does not have them. + register "PchHdaAudioLinkSsp1" = "0" + register "PchHdaAudioLinkDmic0" = "0" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI0 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| | before memory is up | + #| I2C0 | RFU | + #| I2C2 | PS175 | + #| I2C3 | MST | + #| I2C4 | Audio | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .gspi[0] = { + .speed_mhz = 1, + .early_init = 1, + }, + .i2c[0] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 0, + .fall_time_ns = 0, + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 60, + .fall_time_ns = 60, + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 60, + .fall_time_ns = 60, + }, + .i2c[4] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 60, + .fall_time_ns = 60, + }, + }" + + # PCIe port 7 for LAN + register "PcieRpEnable[6]" = "1" + register "PcieRpLtrEnable[6]" = "1" + # PCIe port 11 (x2) for NVMe hybrid storage devices + register "PcieRpEnable[10]" = "1" + register "PcieRpLtrEnable[10]" = "1" + # Uses CLK SRC 0 + register "PcieClkSrcUsage[0]" = "6" + register "PcieClkSrcClkReq[0]" = "0" + + # GPIO for SD card detect + register "sdcard_cd_gpio" = "vSD3_CD_B" + + # SATA port 1 Gen3 Strength + # Port1 Tx De-Emphasis = 20*log(0x20/64) = -6dB + register "sata_port[1].TxGen3DeEmphEnable" = "1" + register "sata_port[1].TxGen3DeEmph" = "0x20"
device domain 0 on + device pci 14.0 on + chip drivers/usb/acpi + device usb 0.0 on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Front Left"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(0, 0)" + device usb 2.0 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port Rear"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 3)" + device usb 2.1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Front Right"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(0, 1)" + device usb 2.2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Rear Right"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device usb 2.3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Rear Middle"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device usb 2.4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Rear Left"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 0)" + device usb 2.5 on end + end + chip drivers/usb/acpi + device usb 2.6 off end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Front Left"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(0, 0)" + device usb 3.0 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Front Right"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(0, 1)" + device usb 3.1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Rear Right"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device usb 3.2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Rear"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 3)" + device usb 3.3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Rear Left"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 0)" + device usb 3.4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Rear Middle"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device usb 3.5 on end + end + end + end + end # USB xHCI + device pci 15.0 off + # RFU - Reserved for Future Use. + end # I2C #0 + device pci 15.1 off end # I2C #1 + device pci 15.2 on + chip drivers/i2c/generic + register "hid" = ""1AF80175"" + register "name" = ""PS17"" + register "desc" = ""Parade PS175"" + device i2c 4a on end + end + end # I2C #2, PCON PS175. + device pci 15.3 on + chip drivers/i2c/generic + register "hid" = ""10EC2142"" + register "name" = ""RTD2"" + register "desc" = ""Realtek RTD2142"" + device i2c 4a on end + end + end # I2C #3, Realtek RTD2142. + device pci 19.0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Realtek RT5682"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)" + register "property_count" = "1" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + end #I2C #4 + device pci 1a.0 on end # eMMC + device pci 1c.6 on + chip drivers/net + register "customized_leds" = "0x05af" + register "wake" = "GPE0_DW1_07" # GPP_C7 + register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A18)" + register "stop_delay_ms" = "12" # NIC needs time to quiesce + register "stop_off_delay_ms" = "1" + register "has_power_resource" = "1" + register "device_index" = "0" + device pci 00.0 on end + end + end # RTL8111H Ethernet NIC + device pci 1d.2 on end # PCI Express Port 11 (X2 NVMe) + device pci 1e.3 off end # GSPI #1 end
+ # VR Settings Configuration for 4 Domains + #+----------------+-------+-------+-------+-------+ + #| Domain/Setting | SA | IA | GTUS | GTS | + #+----------------+-------+-------+-------+-------+ + #| Psi1Threshold | 20A | 20A | 20A | 20A | + #| Psi2Threshold | 5A | 5A | 5A | 5A | + #| Psi3Threshold | 1A | 1A | 1A | 1A | + #| Psi3Enable | 1 | 1 | 1 | 1 | + #| Psi4Enable | 1 | 1 | 1 | 1 | + #| ImonSlope | 0 | 0 | 0 | 0 | + #| ImonOffset | 0 | 0 | 0 | 0 | + #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | + #| AcLoadline | 10.04 | 1.81 | 3.19 | 3.19 | + #| DcLoadline | 10.04 | 1.81 | 3.19 | 3.19 | + #+----------------+-------+-------+-------+-------+ + #Note: IccMax settings are moved to SoC code + register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 1004, + .dc_loadline = 1004, + }" + + register "domain_vr_config[VR_IA_CORE]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 181, + .dc_loadline = 181, + }" + + register "domain_vr_config[VR_GT_UNSLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 319, + .dc_loadline = 319, + }" + + register "domain_vr_config[VR_GT_SLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 319, + .dc_loadline = 319, + }" + end
Sam McNally has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42675 )
Change subject: util/mb/google/tmpl/puff: Import overridetree.cb copy ......................................................................
Patch Set 1: Code-Review+2
Paul Fagerburg has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42675 )
Change subject: util/mb/google/tmpl/puff: Import overridetree.cb copy ......................................................................
Patch Set 1: Code-Review+2
That seems like a really large overridetree.cb.
My CR+2 assumes that there isn't a clean way to have most of that in puff and then have the variants just override little bits from puff instead of hatch. Similar to how ec.h now includes puff/ec.h instead of baseboard/ec.h.
Edward O'Callaghan has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42675 )
Change subject: util/mb/google/tmpl/puff: Import overridetree.cb copy ......................................................................
Patch Set 1:
Patch Set 1: Code-Review+2
That seems like a really large overridetree.cb.
My CR+2 assumes that there isn't a clean way to have most of that in puff and then have the variants just override little bits from puff instead of hatch. Similar to how ec.h now includes puff/ec.h instead of baseboard/ec.h.
That is correct. Unfortunately devicetree overrides do not support multi-layer inheritance were, in our case we have `hatch > puff > variant` and so we actually are overriding hatch directly in the case of dt and so `hatch > variant (copy from puff dt)`. Long term it would be nice to add this multi-layer support to dt however that is the current limitation and is a small price to pay to allow us to allow a sister stream puff to hatch to share the same mainboard/ directory. As with all theses thing, somewhere along the way a compromise needs to be taken and this ended up being ours.
Edward O'Callaghan has submitted this change. ( https://review.coreboot.org/c/coreboot/+/42675 )
Change subject: util/mb/google/tmpl/puff: Import overridetree.cb copy ......................................................................
util/mb/google/tmpl/puff: Import overridetree.cb copy
BUG=b:154071868 BRANCH=none TEST=none
Change-Id: I40faa5f80e78cd73ba5ef977574f7f662c0ab8a1 Signed-off-by: Edward O'Callaghan quasisec@google.com Reviewed-on: https://review.coreboot.org/c/coreboot/+/42675 Tested-by: build bot (Jenkins) no-reply@coreboot.org Reviewed-by: Sam McNally sammc@google.com Reviewed-by: Paul Fagerburg pfagerburg@chromium.org --- M util/mainboard/google/puff/template/overridetree.cb 1 file changed, 400 insertions(+), 0 deletions(-)
Approvals: build bot (Jenkins): Verified Paul Fagerburg: Looks good to me, approved Sam McNally: Looks good to me, approved
diff --git a/util/mainboard/google/puff/template/overridetree.cb b/util/mainboard/google/puff/template/overridetree.cb index abbcaaa..ededac4 100644 --- a/util/mainboard/google/puff/template/overridetree.cb +++ b/util/mainboard/google/puff/template/overridetree.cb @@ -1,6 +1,406 @@ chip soc/intel/cannonlake + # Enable heci communication + register "HeciEnabled" = "1" + + # Auto-switch between X4 NVMe and X2 NVMe. + register "TetonGlacierMode" = "1" + + register "SerialIoDevMode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoDisabled, + [PchSerialIoIndexI2C1] = PchSerialIoDisabled, + [PchSerialIoIndexI2C2] = PchSerialIoPci, + [PchSerialIoIndexI2C3] = PchSerialIoPci, + [PchSerialIoIndexI2C4] = PchSerialIoPci, + [PchSerialIoIndexI2C5] = PchSerialIoPci, + [PchSerialIoIndexSPI0] = PchSerialIoPci, + [PchSerialIoIndexSPI1] = PchSerialIoPci, + [PchSerialIoIndexSPI2] = PchSerialIoDisabled, + [PchSerialIoIndexUART0] = PchSerialIoSkipInit, + [PchSerialIoIndexUART1] = PchSerialIoDisabled, + [PchSerialIoIndexUART2] = PchSerialIoDisabled, + }" + + # USB configuration + # NOTE: This only applies to Puff, + # usb2_ports[1] and usb2_ports[3] were swapped on + # reference schematics after Puff has been built. + register "usb2_ports[0]" = "{ + .enable = 1, + .ocpin = OC2, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_11P25MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 2 + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # Type-C Port + register "usb2_ports[2]" = "{ + .enable = 1, + .ocpin = OC3, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 3 + register "usb2_ports[3]" = "{ + .enable = 1, + .ocpin = OC1, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 1 + register "usb2_ports[4]" = "{ + .enable = 1, + .ocpin = OC_SKIP, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A Port 4 + register "usb2_ports[5]" = "{ + .enable = 1, + .ocpin = OC0, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # Type-A port 0 + register "usb2_ports[6]" = "USB2_PORT_EMPTY" + register "usb2_ports[7]" = "USB2_PORT_EMPTY" + register "usb2_ports[8]" = "USB2_PORT_EMPTY" + register "usb2_ports[9]" = "{ + .enable = 1, + .ocpin = OC_SKIP, + .tx_bias = USB2_BIAS_0MV, + .tx_emp_enable = USB2_PRE_EMP_ON, + .pre_emp_bias = USB2_BIAS_28P15MV, + .pre_emp_bit = USB2_HALF_BIT_PRE_EMP, + }" # BT + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC2)" # Type-A Port 2 + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC3)" # Type-A Port 3 + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC1)" # Type-A Port 1 + register "usb3_ports[3]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-C + register "usb3_ports[4]" = "USB3_PORT_DEFAULT(OC0)" # Type-A Port 0 + register "usb3_ports[5]" = "USB3_PORT_DEFAULT(OC_SKIP)" # Type-A Port 4 + + # Enable eMMC HS400 + register "ScsEmmcHs400Enabled" = "1" + + # EMMC Tx CMD Delay + # Refer to EDS-Vol2-14.3.7. + # [14:8] steps of delay for DDR mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for SDR mode, each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_tx_cmd_cntl" = "0x505" + + # EMMC TX DATA Delay 1 + # Refer to EDS-Vol2-14.3.8. + # [14:8] steps of delay for HS400, each 125ps, range: 0 - 78. + # [6:0] steps of delay for SDR104/HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl1" = "0x911" + + # EMMC TX DATA Delay 2 + # Refer to EDS-Vol2-14.3.9. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 79. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 -79. + # [6:0] steps of delay for SDR12, each 125ps. Range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_tx_data_cntl2" = "0x1C262828" + + # EMMC RX CMD/DATA Delay 1 + # Refer to EDS-Vol2-14.3.10. + # [30:24] steps of delay for SDR50, each 125ps, range: 0 - 119. + # [22:16] steps of delay for DDR50, each 125ps, range: 0 - 78. + # [14:8] steps of delay for SDR25/HS50, each 125ps, range: 0 - 119. + # [6:0] steps of delay for SDR12, each 125ps, range: 0 - 119. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl1" = "0x1C16583b" + + # EMMC RX CMD/DATA Delay 2 + # Refer to EDS-Vol2-14.3.12. + # [17:16] stands for Rx Clock before Output Buffer, + # 00: Rx clock after output buffer, + # 01: Rx clock before output buffer, + # 10: Automatic selection based on working mode. + # 11: Reserved + # [14:8] steps of delay for Auto Tuning Mode, each 125ps, range: 0 - 39. + # [6:0] steps of delay for HS200, each 125ps, range: 0 - 79. + register "common_soc_config.emmc_dll.emmc_rx_cmd_data_cntl2" = "0x1001D" + + # EMMC Rx Strobe Delay + # Refer to EDS-Vol2-14.3.11. + # [14:8] Rx Strobe Delay DLL 1(HS400 Mode), each 125ps, range: 0 - 39. + # [6:0] Rx Strobe Delay DLL 2(HS400 Mode), each 125ps, range: 0 - 39. + register "common_soc_config.emmc_dll.emmc_rx_strobe_cntl" = "0x1515" + + # Intel HDA - disable I2S Audio SSP1 and DMIC0 as puff variant does not have them. + register "PchHdaAudioLinkSsp1" = "0" + register "PchHdaAudioLinkDmic0" = "0" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI0 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| | before memory is up | + #| I2C0 | RFU | + #| I2C2 | PS175 | + #| I2C3 | MST | + #| I2C4 | Audio | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .gspi[0] = { + .speed_mhz = 1, + .early_init = 1, + }, + .i2c[0] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 0, + .fall_time_ns = 0, + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 60, + .fall_time_ns = 60, + }, + .i2c[3] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 60, + .fall_time_ns = 60, + }, + .i2c[4] = { + .speed = I2C_SPEED_FAST, + .rise_time_ns = 60, + .fall_time_ns = 60, + }, + }" + + # PCIe port 7 for LAN + register "PcieRpEnable[6]" = "1" + register "PcieRpLtrEnable[6]" = "1" + # PCIe port 11 (x2) for NVMe hybrid storage devices + register "PcieRpEnable[10]" = "1" + register "PcieRpLtrEnable[10]" = "1" + # Uses CLK SRC 0 + register "PcieClkSrcUsage[0]" = "6" + register "PcieClkSrcClkReq[0]" = "0" + + # GPIO for SD card detect + register "sdcard_cd_gpio" = "vSD3_CD_B" + + # SATA port 1 Gen3 Strength + # Port1 Tx De-Emphasis = 20*log(0x20/64) = -6dB + register "sata_port[1].TxGen3DeEmphEnable" = "1" + register "sata_port[1].TxGen3DeEmph" = "0x20"
device domain 0 on + device pci 14.0 on + chip drivers/usb/acpi + device usb 0.0 on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Front Left"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(0, 0)" + device usb 2.0 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port Rear"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 3)" + device usb 2.1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Front Right"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(0, 1)" + device usb 2.2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Rear Right"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device usb 2.3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Rear Middle"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device usb 2.4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Rear Left"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 0)" + device usb 2.5 on end + end + chip drivers/usb/acpi + device usb 2.6 off end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Front Left"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(0, 0)" + device usb 3.0 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Front Right"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(0, 1)" + device usb 3.1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Rear Right"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device usb 3.2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Rear"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 3)" + device usb 3.3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Rear Left"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 0)" + device usb 3.4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Rear Middle"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device usb 3.5 on end + end + end + end + end # USB xHCI + device pci 15.0 off + # RFU - Reserved for Future Use. + end # I2C #0 + device pci 15.1 off end # I2C #1 + device pci 15.2 on + chip drivers/i2c/generic + register "hid" = ""1AF80175"" + register "name" = ""PS17"" + register "desc" = ""Parade PS175"" + device i2c 4a on end + end + end # I2C #2, PCON PS175. + device pci 15.3 on + chip drivers/i2c/generic + register "hid" = ""10EC2142"" + register "name" = ""RTD2"" + register "desc" = ""Realtek RTD2142"" + device i2c 4a on end + end + end # I2C #3, Realtek RTD2142. + device pci 19.0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Realtek RT5682"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_H0)" + register "property_count" = "1" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + end #I2C #4 + device pci 1a.0 on end # eMMC + device pci 1c.6 on + chip drivers/net + register "customized_leds" = "0x05af" + register "wake" = "GPE0_DW1_07" # GPP_C7 + register "stop_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A18)" + register "stop_delay_ms" = "12" # NIC needs time to quiesce + register "stop_off_delay_ms" = "1" + register "has_power_resource" = "1" + register "device_index" = "0" + device pci 00.0 on end + end + end # RTL8111H Ethernet NIC + device pci 1d.2 on end # PCI Express Port 11 (X2 NVMe) + device pci 1e.3 off end # GSPI #1 end
+ # VR Settings Configuration for 4 Domains + #+----------------+-------+-------+-------+-------+ + #| Domain/Setting | SA | IA | GTUS | GTS | + #+----------------+-------+-------+-------+-------+ + #| Psi1Threshold | 20A | 20A | 20A | 20A | + #| Psi2Threshold | 5A | 5A | 5A | 5A | + #| Psi3Threshold | 1A | 1A | 1A | 1A | + #| Psi3Enable | 1 | 1 | 1 | 1 | + #| Psi4Enable | 1 | 1 | 1 | 1 | + #| ImonSlope | 0 | 0 | 0 | 0 | + #| ImonOffset | 0 | 0 | 0 | 0 | + #| VrVoltageLimit | 1.52V | 1.52V | 1.52V | 1.52V | + #| AcLoadline | 10.04 | 1.81 | 3.19 | 3.19 | + #| DcLoadline | 10.04 | 1.81 | 3.19 | 3.19 | + #+----------------+-------+-------+-------+-------+ + #Note: IccMax settings are moved to SoC code + register "domain_vr_config[VR_SYSTEM_AGENT]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 1004, + .dc_loadline = 1004, + }" + + register "domain_vr_config[VR_IA_CORE]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 181, + .dc_loadline = 181, + }" + + register "domain_vr_config[VR_GT_UNSLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 319, + .dc_loadline = 319, + }" + + register "domain_vr_config[VR_GT_SLICED]" = "{ + .vr_config_enable = 1, + .psi1threshold = VR_CFG_AMP(20), + .psi2threshold = VR_CFG_AMP(5), + .psi3threshold = VR_CFG_AMP(1), + .psi3enable = 1, + .psi4enable = 1, + .imon_slope = 0x0, + .imon_offset = 0x0, + .icc_max = 0, + .voltage_limit = 1520, + .ac_loadline = 319, + .dc_loadline = 319, + }" + end
-
Edward O'Callaghan (Code Review) -
Paul Fagerburg (Code Review)
-
Sam McNally (Code Review)