[S] Change in coreboot[main]: mb/google/nissa/var/yavilla: Add 1.2V enable pin in VCM

[Felix Held (Code Review)]

Felix Held has submitted this change. ( https://review.coreboot.org/c/coreboot/+/84211?usp=email )

Change subject: mb/google/nissa/var/yavilla: Add 1.2V enable pin in VCM
......................................................................

mb/google/nissa/var/yavilla: Add 1.2V enable pin in VCM

Add control for the 1.2V enable pin in VCM to comply the mipi camera
power sequence.

2.8V enable --> 1.2V enable --> reset

BUG=b:362386165
TEST=Run ITS test

Change-Id: I495b2e266ee3d24ed3334bb9c173b3993d095e8e
Signed-off-by: Wisley Chen 
Reviewed-on: https://review.coreboot.org/c/coreboot/+/84211
Reviewed-by: Subrata Banik 
Tested-by: build bot (Jenkins) 
Reviewed-by: Eric Lai 
---
M src/mainboard/google/brya/variants/yavilla/overridetree.cb
1 file changed, 7 insertions(+), 4 deletions(-)

Approvals:
  build bot (Jenkins): Verified
  Eric Lai: Looks good to me, approved
  Subrata Banik: Looks good to me, approved

diff --git a/src/mainboard/google/brya/variants/yavilla/overridetree.cb b/src/mainboard/google/brya/variants/yavilla/overridetree.cb
index ee5a3b6..973a16b 100644
--- a/src/mainboard/google/brya/variants/yavilla/overridetree.cb
+++ b/src/mainboard/google/brya/variants/yavilla/overridetree.cb
@@ -404,17 +404,20 @@

#Controls
    			register "gpio_panel.gpio[0].gpio_num" = "GPP_D15"  # EN_PP2800_WCAM_X
-				register "gpio_panel.gpio[1].gpio_num" = "GPP_D3"   # WCAM_RST_L
+				register "gpio_panel.gpio[1].gpio_num" = "GPP_D16"  # EN_PP1800_PP1200_WCAM_X
+				register "gpio_panel.gpio[2].gpio_num" = "GPP_D3"   # WCAM_RST_L

#_ON
-				register "on_seq.ops_cnt" = "2"
+				register "on_seq.ops_cnt" = "3"
    			register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 5)"
    			register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(1, 5)"
+				register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(2, 5)"

#_OFF
-				register "off_seq.ops_cnt" = "2"
+				register "off_seq.ops_cnt" = "3"
+				register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(2, 0)"
    			register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)"
-				register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"
+				register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)"

device i2c 0C on
    				probe WFC WFC_MIPI_OVTI8856