Nick Vaccaro has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/42550 )
Change subject: mb/google/volteer: add overridetree.cb for volteer ......................................................................
mb/google/volteer: add overridetree.cb for volteer
Move volteer-specific devices from baseboard's devicetree.cb into volteer's overridetree.cb file.
Adjust the other variant's overridetree.cb files to correspond to the changes made to the baseboard's devicetree.cb in this change.
BUG=b:159241303, b:154646959 TEST='emerge-volteer coreboot chromeos-bootimage', flash and boot volteer to kernel and verify that the trackpad works.
Change-Id: I30f8266ec87a7cde293c84d3e687d133207b8d59 Signed-off-by: Nick Vaccaro nvaccaro@google.com --- M src/mainboard/google/volteer/variants/baseboard/devicetree.cb M src/mainboard/google/volteer/variants/halvor/overridetree.cb M src/mainboard/google/volteer/variants/malefor/overridetree.cb M src/mainboard/google/volteer/variants/terrador/overridetree.cb M src/mainboard/google/volteer/variants/trondo/overridetree.cb M src/mainboard/google/volteer/variants/volteer/overridetree.cb 6 files changed, 334 insertions(+), 159 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/50/42550/1
diff --git a/src/mainboard/google/volteer/variants/baseboard/devicetree.cb b/src/mainboard/google/volteer/variants/baseboard/devicetree.cb index 4478a96..abd4535 100644 --- a/src/mainboard/google/volteer/variants/baseboard/devicetree.cb +++ b/src/mainboard/google/volteer/variants/baseboard/devicetree.cb @@ -303,70 +303,9 @@ register "wake" = "GPE0_PME_B0" device pci 14.3 on end # CNVi: WiFi 0xA0F0 - A0F3 end - device pci 15.0 on end # I2C #0 0xA0E8 - device pci 15.1 on - chip drivers/i2c/hid - register "generic.hid" = ""GDIX0000"" - register "generic.desc" = ""Goodix Touchscreen"" - register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - register "generic.probed" = "1" - register "generic.reset_gpio" = - "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" - register "generic.reset_delay_ms" = "120" - register "generic.reset_off_delay_ms" = "3" - register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" - register "generic.enable_delay_ms" = "12" - register "generic.has_power_resource" = "1" - register "hid_desc_reg_offset" = "0x01" - device i2c 14 on end - end - chip drivers/i2c/hid - register "generic.hid" = ""ELAN90FC"" - register "generic.desc" = ""ELAN Touchscreen"" - register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - register "generic.probed" = "1" - register "generic.reset_gpio" = - "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" - register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" - register "generic.reset_delay_ms" = "20" - register "generic.has_power_resource" = "1" - register "generic.disable_gpio_export_in_crs" = "1" - register "hid_desc_reg_offset" = "0x01" - device i2c 10 on end - end - end # I2C1 0xA0E9 - device pci 15.2 on - chip drivers/i2c/sx9310 - register "desc" = ""SAR0 Proximity Sensor"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" - register "speed" = "I2C_SPEED_FAST" - register "uid" = "0" - register "reg_prox_ctrl0" = "0x10" - register "reg_prox_ctrl1" = "0x00" - register "reg_prox_ctrl2" = "0x84" - register "reg_prox_ctrl3" = "0x0e" - register "reg_prox_ctrl4" = "0x07" - register "reg_prox_ctrl5" = "0xc6" - register "reg_prox_ctrl6" = "0x20" - register "reg_prox_ctrl7" = "0x0d" - register "reg_prox_ctrl8" = "0x8d" - register "reg_prox_ctrl9" = "0x43" - register "reg_prox_ctrl10" = "0x1f" - register "reg_prox_ctrl11" = "0x00" - register "reg_prox_ctrl12" = "0x00" - register "reg_prox_ctrl13" = "0x00" - register "reg_prox_ctrl14" = "0x00" - register "reg_prox_ctrl15" = "0x00" - register "reg_prox_ctrl16" = "0x00" - register "reg_prox_ctrl17" = "0x00" - register "reg_prox_ctrl18" = "0x00" - register "reg_prox_ctrl19" = "0x00" - register "reg_sar_ctrl0" = "0x50" - register "reg_sar_ctrl1" = "0x8a" - register "reg_sar_ctrl2" = "0x3c" - device i2c 28 on end - end - end # I2C2 0xA0EA + device pci 15.0 on end # I2C #0 0xA0E8 + device pci 15.1 on end # I2C1 0xA0E9 + device pci 15.2 on end # I2C2 0xA0EA device pci 15.3 on end # I2C3 0xA0EB
device pci 16.0 on end # HECI1 0xA0E0 @@ -379,16 +318,7 @@ device pci 17.0 on end # SATA 0xA0D3
device pci 19.0 on end # I2C4 0xA0C5 - device pci 19.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" - register "wake" = "GPE0_DW2_15" - register "probed" = "1" - device i2c 15 on end - end - end # I2C5 0xA0C6 + device pci 19.1 on end # I2C5 0xA0C6 device pci 19.2 off end # UART2 0xA0C7
device pci 1c.0 on end # RP1 0xA0B8 diff --git a/src/mainboard/google/volteer/variants/halvor/overridetree.cb b/src/mainboard/google/volteer/variants/halvor/overridetree.cb index 20a90cc..e53132a 100644 --- a/src/mainboard/google/volteer/variants/halvor/overridetree.cb +++ b/src/mainboard/google/volteer/variants/halvor/overridetree.cb @@ -46,6 +46,79 @@ device i2c 32 on end end end # I2C #0 0xA0E8 + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 device pci 1f.3 on chip drivers/generic/max98357a register "hid" = ""MX98357A"" diff --git a/src/mainboard/google/volteer/variants/malefor/overridetree.cb b/src/mainboard/google/volteer/variants/malefor/overridetree.cb index 8d4c6ea..84493f8 100644 --- a/src/mainboard/google/volteer/variants/malefor/overridetree.cb +++ b/src/mainboard/google/volteer/variants/malefor/overridetree.cb @@ -19,6 +19,47 @@ device i2c 5d on end end end # I2C1 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 end - end diff --git a/src/mainboard/google/volteer/variants/terrador/overridetree.cb b/src/mainboard/google/volteer/variants/terrador/overridetree.cb index 75422d8..4bff10d 100644 --- a/src/mainboard/google/volteer/variants/terrador/overridetree.cb +++ b/src/mainboard/google/volteer/variants/terrador/overridetree.cb @@ -1,4 +1,77 @@ chip soc/intel/tigerlake device domain 0 on + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 end end diff --git a/src/mainboard/google/volteer/variants/trondo/overridetree.cb b/src/mainboard/google/volteer/variants/trondo/overridetree.cb index 75422d8..4bff10d 100644 --- a/src/mainboard/google/volteer/variants/trondo/overridetree.cb +++ b/src/mainboard/google/volteer/variants/trondo/overridetree.cb @@ -1,4 +1,77 @@ chip soc/intel/tigerlake device domain 0 on + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 end end diff --git a/src/mainboard/google/volteer/variants/volteer/overridetree.cb b/src/mainboard/google/volteer/variants/volteer/overridetree.cb index 9e5ef4b..4bff10d 100644 --- a/src/mainboard/google/volteer/variants/volteer/overridetree.cb +++ b/src/mainboard/google/volteer/variants/volteer/overridetree.cb @@ -1,92 +1,77 @@ chip soc/intel/tigerlake device domain 0 on - device pci 15.0 on - chip drivers/i2c/generic - register "hid" = ""10EC5682"" - register "name" = ""RT58"" - register "desc" = ""Headset Codec"" - register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F8)" - # Set the jd_src to RT5668_JD1 for jack detection - register "property_count" = "1" - register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" - register "property_list[0].name" = ""realtek,jd-src"" - register "property_list[0].integer" = "1" - device i2c 1a on - probe AUDIO MAX98357_ALC5682I_I2S - probe AUDIO MAX98373_ALC5682I_I2S - end + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end end - chip drivers/i2c/max98373 - register "vmon_slot_no" = "0" - register "imon_slot_no" = "1" + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" register "uid" = "0" - register "desc" = ""Right Speaker Amp"" - register "name" = ""MAXR"" - device i2c 31 on - probe AUDIO MAX98373_ALC5682I_I2S - end + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end end - chip drivers/i2c/max98373 - register "vmon_slot_no" = "2" - register "imon_slot_no" = "3" - register "uid" = "1" - register "desc" = ""Left Speaker Amp"" - register "name" = ""MAXL"" - device i2c 32 on - probe AUDIO MAX98373_ALC5682I_I2S - end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end end - end - device pci 1f.3 on - chip drivers/generic/max98357a - register "hid" = ""MX98357A"" - register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A10)" - register "sdmode_delay" = "5" - device generic 0 on - probe AUDIO MAX98357_ALC5682I_I2S - end - end - chip drivers/intel/soundwire - device generic 0 on - probe AUDIO MAX98373_ALC5682_SNDW - chip drivers/soundwire/alc5682 - # SoundWire Link 0 ID 1 - register "desc" = ""Headset Codec"" - device generic 0.1 on end - end - chip drivers/soundwire/max98373 - # SoundWire Link 1 ID 3 - register "desc" = ""Left Speaker Amp"" - device generic 1.3 on end - end - chip drivers/soundwire/max98373 - # SoundWire Link 1 ID 7 - register "desc" = ""Right Speaker Amp"" - device generic 1.7 on end - end - end - end - end - device pci 1f.2 hidden - # The pmc_mux chip driver is a placeholder for the - # PMC.MUX device in the ACPI hierarchy. - chip drivers/intel/pmc_mux - device generic 0 on - chip drivers/intel/pmc_mux/con - register "usb2_port_number" = "9" - register "usb3_port_number" = "1" - # SBU & HSL follow CC - device generic 0 on end - end - chip drivers/intel/pmc_mux/con - register "usb2_port_number" = "4" - register "usb3_port_number" = "2" - # SBU is fixed, HSL follows CC - register "sbu_orientation" = "TYPEC_ORIENTATION_NORMAL" - device generic 1 on end - end - end - end - end # PMC + end # I2C5 0xA0C6 end end
Hello build bot (Jenkins),
I'd like you to reexamine a change. Please visit
https://review.coreboot.org/c/coreboot/+/42550
to look at the new patch set (#3).
Change subject: mb/google/volteer: add overridetree.cb for volteer ......................................................................
mb/google/volteer: add overridetree.cb for volteer
Move the following volteer-specific devices from baseboard's devicetree.cb into volteer's overridetree.cb file: - Goodix Touchscreen - ELAN Touchscreen - ELAN Touchpad - SAR0 Proximity Sensor
Adjust the other variant's overridetree.cb files to correspond to the changes made to the baseboard's devicetree.cb in this change.
BUG=b:159241303, b:154646959 TEST='emerge-volteer coreboot chromeos-bootimage', flash and boot volteer to kernel and verify that the trackpad works.
Change-Id: I30f8266ec87a7cde293c84d3e687d133207b8d59 Signed-off-by: Nick Vaccaro nvaccaro@google.com --- M src/mainboard/google/volteer/variants/baseboard/devicetree.cb M src/mainboard/google/volteer/variants/halvor/overridetree.cb M src/mainboard/google/volteer/variants/malefor/overridetree.cb M src/mainboard/google/volteer/variants/terrador/overridetree.cb M src/mainboard/google/volteer/variants/trondo/overridetree.cb M src/mainboard/google/volteer/variants/volteer/overridetree.cb 6 files changed, 334 insertions(+), 159 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/50/42550/3
William Wei has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42550 )
Change subject: mb/google/volteer: add overridetree.cb for volteer ......................................................................
Patch Set 3: Code-Review+1
LGTM on malefor side.
Frank Wu has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42550 )
Change subject: mb/google/volteer: add overridetree.cb for volteer ......................................................................
Patch Set 3: Code-Review+1
Tim Wawrzynczak has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42550 )
Change subject: mb/google/volteer: add overridetree.cb for volteer ......................................................................
Patch Set 3:
(1 comment)
https://review.coreboot.org/c/coreboot/+/42550/3//COMMIT_MSG Commit Message:
https://review.coreboot.org/c/coreboot/+/42550/3//COMMIT_MSG@7 PS3, Line 7: add overridetree.cb for volteer there already is an overridetree.cb for volteer 😊 maybe say something like, clean up baseboard devicetree or move variant-specific devices into variant trees ?
Hello Frank Wu, William Wei, build bot (Jenkins), David Wu, Caveh Jalali, Tim Wawrzynczak, Duncan Laurie,
I'd like you to reexamine a change. Please visit
https://review.coreboot.org/c/coreboot/+/42550
to look at the new patch set (#4).
Change subject: mb/google/volteer: move volteer devices to overridetree.cb ......................................................................
mb/google/volteer: move volteer devices to overridetree.cb
Move the following volteer-specific devices from baseboard's devicetree.cb into volteer's overridetree.cb file: - Goodix Touchscreen - ELAN Touchscreen - ELAN Touchpad - SAR0 Proximity Sensor
Adjust the other variant's overridetree.cb files to correspond to the changes made to the baseboard's devicetree.cb in this change.
BUG=b:159241303, b:154646959 TEST='emerge-volteer coreboot chromeos-bootimage', flash and boot volteer to kernel and verify that the trackpad works.
Change-Id: I30f8266ec87a7cde293c84d3e687d133207b8d59 Signed-off-by: Nick Vaccaro nvaccaro@google.com --- M src/mainboard/google/volteer/variants/baseboard/devicetree.cb M src/mainboard/google/volteer/variants/halvor/overridetree.cb M src/mainboard/google/volteer/variants/malefor/overridetree.cb M src/mainboard/google/volteer/variants/terrador/overridetree.cb M src/mainboard/google/volteer/variants/trondo/overridetree.cb M src/mainboard/google/volteer/variants/volteer/overridetree.cb 6 files changed, 338 insertions(+), 75 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/50/42550/4
Nick Vaccaro has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42550 )
Change subject: mb/google/volteer: move volteer devices to overridetree.cb ......................................................................
Patch Set 4:
(1 comment)
https://review.coreboot.org/c/coreboot/+/42550/3//COMMIT_MSG Commit Message:
https://review.coreboot.org/c/coreboot/+/42550/3//COMMIT_MSG@7 PS3, Line 7: add overridetree.cb for volteer
there already is an overridetree. […]
Done
Tim Wawrzynczak has posted comments on this change. ( https://review.coreboot.org/c/coreboot/+/42550 )
Change subject: mb/google/volteer: move volteer devices to overridetree.cb ......................................................................
Patch Set 4: Code-Review+2
Patrick Georgi has submitted this change. ( https://review.coreboot.org/c/coreboot/+/42550 )
Change subject: mb/google/volteer: move volteer devices to overridetree.cb ......................................................................
mb/google/volteer: move volteer devices to overridetree.cb
Move the following volteer-specific devices from baseboard's devicetree.cb into volteer's overridetree.cb file: - Goodix Touchscreen - ELAN Touchscreen - ELAN Touchpad - SAR0 Proximity Sensor
Adjust the other variant's overridetree.cb files to correspond to the changes made to the baseboard's devicetree.cb in this change.
BUG=b:159241303, b:154646959 TEST='emerge-volteer coreboot chromeos-bootimage', flash and boot volteer to kernel and verify that the trackpad works.
Change-Id: I30f8266ec87a7cde293c84d3e687d133207b8d59 Signed-off-by: Nick Vaccaro nvaccaro@google.com Reviewed-on: https://review.coreboot.org/c/coreboot/+/42550 Tested-by: build bot (Jenkins) no-reply@coreboot.org Reviewed-by: Tim Wawrzynczak twawrzynczak@chromium.org --- M src/mainboard/google/volteer/variants/baseboard/devicetree.cb M src/mainboard/google/volteer/variants/halvor/overridetree.cb M src/mainboard/google/volteer/variants/malefor/overridetree.cb M src/mainboard/google/volteer/variants/terrador/overridetree.cb M src/mainboard/google/volteer/variants/trondo/overridetree.cb M src/mainboard/google/volteer/variants/volteer/overridetree.cb 6 files changed, 338 insertions(+), 75 deletions(-)
Approvals: build bot (Jenkins): Verified Tim Wawrzynczak: Looks good to me, approved
diff --git a/src/mainboard/google/volteer/variants/baseboard/devicetree.cb b/src/mainboard/google/volteer/variants/baseboard/devicetree.cb index 9d044b9..705da1d 100644 --- a/src/mainboard/google/volteer/variants/baseboard/devicetree.cb +++ b/src/mainboard/google/volteer/variants/baseboard/devicetree.cb @@ -309,70 +309,9 @@ register "wake" = "GPE0_PME_B0" device pci 14.3 on end # CNVi: WiFi 0xA0F0 - A0F3 end - device pci 15.0 on end # I2C #0 0xA0E8 - device pci 15.1 on - chip drivers/i2c/hid - register "generic.hid" = ""GDIX0000"" - register "generic.desc" = ""Goodix Touchscreen"" - register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - register "generic.probed" = "1" - register "generic.reset_gpio" = - "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" - register "generic.reset_delay_ms" = "120" - register "generic.reset_off_delay_ms" = "3" - register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" - register "generic.enable_delay_ms" = "12" - register "generic.has_power_resource" = "1" - register "hid_desc_reg_offset" = "0x01" - device i2c 14 on end - end - chip drivers/i2c/hid - register "generic.hid" = ""ELAN90FC"" - register "generic.desc" = ""ELAN Touchscreen"" - register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" - register "generic.probed" = "1" - register "generic.reset_gpio" = - "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" - register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" - register "generic.reset_delay_ms" = "20" - register "generic.has_power_resource" = "1" - register "generic.disable_gpio_export_in_crs" = "1" - register "hid_desc_reg_offset" = "0x01" - device i2c 10 on end - end - end # I2C1 0xA0E9 - device pci 15.2 on - chip drivers/i2c/sx9310 - register "desc" = ""SAR0 Proximity Sensor"" - register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" - register "speed" = "I2C_SPEED_FAST" - register "uid" = "0" - register "reg_prox_ctrl0" = "0x10" - register "reg_prox_ctrl1" = "0x00" - register "reg_prox_ctrl2" = "0x84" - register "reg_prox_ctrl3" = "0x0e" - register "reg_prox_ctrl4" = "0x07" - register "reg_prox_ctrl5" = "0xc6" - register "reg_prox_ctrl6" = "0x20" - register "reg_prox_ctrl7" = "0x0d" - register "reg_prox_ctrl8" = "0x8d" - register "reg_prox_ctrl9" = "0x43" - register "reg_prox_ctrl10" = "0x1f" - register "reg_prox_ctrl11" = "0x00" - register "reg_prox_ctrl12" = "0x00" - register "reg_prox_ctrl13" = "0x00" - register "reg_prox_ctrl14" = "0x00" - register "reg_prox_ctrl15" = "0x00" - register "reg_prox_ctrl16" = "0x00" - register "reg_prox_ctrl17" = "0x00" - register "reg_prox_ctrl18" = "0x00" - register "reg_prox_ctrl19" = "0x00" - register "reg_sar_ctrl0" = "0x50" - register "reg_sar_ctrl1" = "0x8a" - register "reg_sar_ctrl2" = "0x3c" - device i2c 28 on end - end - end # I2C2 0xA0EA + device pci 15.0 on end # I2C #0 0xA0E8 + device pci 15.1 on end # I2C1 0xA0E9 + device pci 15.2 on end # I2C2 0xA0EA device pci 15.3 on end # I2C3 0xA0EB
device pci 16.0 on end # HECI1 0xA0E0 @@ -385,16 +324,7 @@ device pci 17.0 on end # SATA 0xA0D3
device pci 19.0 on end # I2C4 0xA0C5 - device pci 19.1 on - chip drivers/i2c/generic - register "hid" = ""ELAN0000"" - register "desc" = ""ELAN Touchpad"" - register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" - register "wake" = "GPE0_DW2_15" - register "probed" = "1" - device i2c 15 on end - end - end # I2C5 0xA0C6 + device pci 19.1 on end # I2C5 0xA0C6 device pci 19.2 off end # UART2 0xA0C7
device pci 1c.0 on end # RP1 0xA0B8 diff --git a/src/mainboard/google/volteer/variants/halvor/overridetree.cb b/src/mainboard/google/volteer/variants/halvor/overridetree.cb index 20a90cc..e53132a 100644 --- a/src/mainboard/google/volteer/variants/halvor/overridetree.cb +++ b/src/mainboard/google/volteer/variants/halvor/overridetree.cb @@ -46,6 +46,79 @@ device i2c 32 on end end end # I2C #0 0xA0E8 + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 device pci 1f.3 on chip drivers/generic/max98357a register "hid" = ""MX98357A"" diff --git a/src/mainboard/google/volteer/variants/malefor/overridetree.cb b/src/mainboard/google/volteer/variants/malefor/overridetree.cb index 8d4c6ea..84493f8 100644 --- a/src/mainboard/google/volteer/variants/malefor/overridetree.cb +++ b/src/mainboard/google/volteer/variants/malefor/overridetree.cb @@ -19,6 +19,47 @@ device i2c 5d on end end end # I2C1 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 end - end diff --git a/src/mainboard/google/volteer/variants/terrador/overridetree.cb b/src/mainboard/google/volteer/variants/terrador/overridetree.cb index 75422d8..4bff10d 100644 --- a/src/mainboard/google/volteer/variants/terrador/overridetree.cb +++ b/src/mainboard/google/volteer/variants/terrador/overridetree.cb @@ -1,4 +1,77 @@ chip soc/intel/tigerlake device domain 0 on + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 end end diff --git a/src/mainboard/google/volteer/variants/trondo/overridetree.cb b/src/mainboard/google/volteer/variants/trondo/overridetree.cb index 75422d8..4bff10d 100644 --- a/src/mainboard/google/volteer/variants/trondo/overridetree.cb +++ b/src/mainboard/google/volteer/variants/trondo/overridetree.cb @@ -1,4 +1,77 @@ chip soc/intel/tigerlake device domain 0 on + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 end end diff --git a/src/mainboard/google/volteer/variants/volteer/overridetree.cb b/src/mainboard/google/volteer/variants/volteer/overridetree.cb index 9e5ef4b..24b869c 100644 --- a/src/mainboard/google/volteer/variants/volteer/overridetree.cb +++ b/src/mainboard/google/volteer/variants/volteer/overridetree.cb @@ -37,6 +37,79 @@ end end end + device pci 15.1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.enable_delay_ms" = "12" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 14 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_EDGE_LOW(GPP_E7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C10)" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A8)" + register "generic.reset_delay_ms" = "20" + register "generic.has_power_resource" = "1" + register "generic.disable_gpio_export_in_crs" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 10 on end + end + end # I2C1 0xA0E9 + device pci 15.2 on + chip drivers/i2c/sx9310 + register "desc" = ""SAR0 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "0" + register "reg_prox_ctrl0" = "0x10" + register "reg_prox_ctrl1" = "0x00" + register "reg_prox_ctrl2" = "0x84" + register "reg_prox_ctrl3" = "0x0e" + register "reg_prox_ctrl4" = "0x07" + register "reg_prox_ctrl5" = "0xc6" + register "reg_prox_ctrl6" = "0x20" + register "reg_prox_ctrl7" = "0x0d" + register "reg_prox_ctrl8" = "0x8d" + register "reg_prox_ctrl9" = "0x43" + register "reg_prox_ctrl10" = "0x1f" + register "reg_prox_ctrl11" = "0x00" + register "reg_prox_ctrl12" = "0x00" + register "reg_prox_ctrl13" = "0x00" + register "reg_prox_ctrl14" = "0x00" + register "reg_prox_ctrl15" = "0x00" + register "reg_prox_ctrl16" = "0x00" + register "reg_prox_ctrl17" = "0x00" + register "reg_prox_ctrl18" = "0x00" + register "reg_prox_ctrl19" = "0x00" + register "reg_sar_ctrl0" = "0x50" + register "reg_sar_ctrl1" = "0x8a" + register "reg_sar_ctrl2" = "0x3c" + device i2c 28 on end + end + end # I2C2 0xA0EA + device pci 19.1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_E15_IRQ)" + register "wake" = "GPE0_DW2_15" + register "probed" = "1" + device i2c 15 on end + end + end # I2C5 0xA0C6 device pci 1f.3 on chip drivers/generic/max98357a register "hid" = ""MX98357A""
-
Frank Wu (Code Review) -
Nick Vaccaro (Code Review)
-
Patrick Georgi (Code Review)
-
Tim Wawrzynczak (Code Review)
-
William Wei (Code Review)