Attention is currently required from: Pranava Y N, Subrata Banik.
Jérémy Compostella has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/84407?usp=email )
Change subject: mb/google/fatcat: Add override tree ......................................................................
mb/google/fatcat: Add override tree
BUG=b:348678529 TEST=Boot on google fatcat board
Change-Id: I914f73ff06bfb801fc319b45b23d7ce4cb7a6d53 Signed-off-by: Jeremy Compostella jeremy.compostella@intel.com --- M src/mainboard/google/fatcat/Kconfig A src/mainboard/google/fatcat/variants/fatcat/overridetree.cb 2 files changed, 682 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/07/84407/1
diff --git a/src/mainboard/google/fatcat/Kconfig b/src/mainboard/google/fatcat/Kconfig index a519802..a47a2a4 100644 --- a/src/mainboard/google/fatcat/Kconfig +++ b/src/mainboard/google/fatcat/Kconfig @@ -128,6 +128,9 @@ string default "fatcat" if BOARD_GOOGLE_MODEL_FATCAT
+config OVERRIDE_DEVICETREE + default "variants/$(CONFIG_VARIANT_DIR)/overridetree.cb" + config VBOOT select VBOOT_LID_SWITCH
diff --git a/src/mainboard/google/fatcat/variants/fatcat/overridetree.cb b/src/mainboard/google/fatcat/variants/fatcat/overridetree.cb new file mode 100644 index 0000000..fc406a2 --- /dev/null +++ b/src/mainboard/google/fatcat/variants/fatcat/overridetree.cb @@ -0,0 +1,679 @@ +chip soc/intel/pantherlake + + # GPE configuration + # Note that GPE events called out in ASL code rely on this + # route. i.e. If this route changes then the affected GPE + # offset bits also need to be changed. + register "pmc_gpe0_dw0" = "GPP_B" + register "pmc_gpe0_dw1" = "GPP_D" + register "pmc_gpe0_dw2" = "GPP_E" + + # FSP configuration + + # Enable CNVi BT + register "cnvi_bt_core" = "true" + + # Enable CNVi WiFi + register "cnvi_wifi_core" = "true" + + register "usb2_ports[0]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C0 + register "usb2_ports[1]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C1 + register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C2 + register "usb2_ports[3]" = "USB2_PORT_TYPE_C(OC_SKIP)" # USB2_C3 + register "usb2_ports[4]" = "USB2_PORT_MID(OC0)" # Type-A Port A0 + register "usb2_ports[5]" = "USB2_PORT_MID(OC0)" # Type-A Port A1 & WWAN with rework + register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # FPS connector + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # CNVi BT or discrete BT + + register "usb2_port_reset_msg_en[0]" = "1" + register "usb2_port_reset_msg_en[1]" = "1" + register "usb2_port_reset_msg_en[2]" = "1" + register "usb2_port_reset_msg_en[3]" = "1" + + register "usb3_ports[0]" = "USB3_PORT_DEFAULT(OC0)" # USB3.2_Type-A1 / M.2 WWAN + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC0)" # USB3.2_Type-A0 / USB Flex Connector + + register "tcss_ports[0]" = "TCSS_PORT_DEFAULT(OC_SKIP)" + register "tcss_ports[1]" = "TCSS_PORT_DEFAULT(OC_SKIP)" + register "tcss_ports[2]" = "TCSS_PORT_DEFAULT(OC_SKIP)" + register "tcss_ports[3]" = "TCSS_PORT_DEFAULT(OC_SKIP)" + + register "tcss_cap_policy[0]" = "7" + register "tcss_cap_policy[1]" = "7" + register "tcss_cap_policy[2]" = "7" + register "tcss_cap_policy[3]" = "7" + + # EC host command ranges are in 0x800-0x8ff & 0x200-0x20f + register "gen1_dec" = "0x00fc0801" + register "gen2_dec" = "0x000c0201" + # EC memory map range is 0x900-0x9ff + register "gen3_dec" = "0x00fc0901" + + # This disabled autonomous GPIO power management for early PO + register "gpio_override_pm" = "1" + register "gpio_pm[COMM_0]" = "0" + register "gpio_pm[COMM_1]" = "0" + register "gpio_pm[COMM_3]" = "0" + register "gpio_pm[COMM_4]" = "0" + register "gpio_pm[COMM_5]" = "0" + + # Enable EDP in PortA + register "ddi_port_A_config" = "1" + register "ddi_ports_config" = "{ + [DDI_PORT_A] = DDI_ENABLE_HPD | DDI_ENABLE_DDC, + }" + + # TCSS USB3 + register "tcss_aux_ori" = "1" + + # Enable s0ix + register "s0ix_enable" = "1" + + register "dptf_enable" = "0" + + register "serial_io_i2c_mode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoPci, + [PchSerialIoIndexI2C1] = PchSerialIoPci, + [PchSerialIoIndexI2C2] = PchSerialIoPci, + [PchSerialIoIndexI2C3] = PchSerialIoPci, + [PchSerialIoIndexI2C4] = PchSerialIoPci, + [PchSerialIoIndexI2C5] = PchSerialIoPci, + }" + + register "serial_io_gspi_mode" = "{ + [PchSerialIoIndexGSPI0] = PchSerialIoPci, + [PchSerialIoIndexGSPI1] = PchSerialIoPci, + }" + + register "serial_io_gspi_cs_mode" = "{ + [PchSerialIoIndexGSPI0] = PchSerialIoDisabled, + [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, + }" + + register "serial_io_gspi_cs_state" = "{ + [PchSerialIoIndexGSPI0] = PchSerialIoDisabled, + [PchSerialIoIndexGSPI1] = PchSerialIoDisabled, + }" + + register "serial_io_uart_mode" = "{ + [PchSerialIoIndexUART0] = PchSerialIoPci, + [PchSerialIoIndexUART1] = PchSerialIoDisabled, + [PchSerialIoIndexUART2] = PchSerialIoDisabled, + }" + + # HD Audio + register "pch_hda_dsp_enable" = "1" + register "pch_hda_idisp_link_tmode" = "HDA_TMODE_8T" + register "pch_hda_idisp_link_frequency" = "HDA_LINKFREQ_96MHZ" + register "pch_hda_idisp_codec_enable" = "1" + + #register "pch_hda_sdi_enable[0]" = "1" + #register "pch_hda_sdi_enable[1]" = "0" + register "cnvi_bt_audio_offload" = "true" + + # Intel Common SoC Config + register "common_soc_config" = "{ + .chipset_lockdown = CHIPSET_LOCKDOWN_COREBOOT, + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[3] = { + .early_init = 1, + .speed = I2C_SPEED_FAST, + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + }, + }" + + device domain 0 on + device ref igpu on end + device ref ipu on + chip drivers/intel/mipi_camera + register "acpi_uid" = "0x50000" + register "acpi_name" = ""IPU0"" + register "device_type" = "INTEL_ACPI_CAMERA_CIO2" + register "cio2_num_ports" = "2" + register "cio2_lanes_used" = "{4,2}" + register "cio2_lane_endpoint[0]" = ""^I2C1.CAM0"" + register "cio2_lane_endpoint[1]" = ""^I2C2.CAM1"" + register "cio2_prt[0]" = "0" + register "cio2_prt[1]" = "2" + device generic 0 on end + end + end + device ref dtt off end + device ref npu on end + device ref iaa off end + + device ref heci1 on end + + device ref thc0 on end + device ref thc1 off end + + device ref tbt_pcie_rp0 on end + device ref tbt_pcie_rp1 on end + device ref tbt_pcie_rp2 on end + device ref tbt_pcie_rp3 on end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(4, 2)" + device ref tcss_usb3_port0 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 2)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C2"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(2, 2)" + device ref tcss_usb3_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C3"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref tcss_usb3_port3 on end + end + end + end + end + + device ref tcss_dma0 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)" + use tcss_usb3_port0 as dfp[0].typec_port + device generic 0 on end + end + chip drivers/intel/usb4/retimer + register "dfp[1].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)" + use tcss_usb3_port1 as dfp[1].typec_port + device generic 0 on end + end + end + device ref tcss_dma1 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)" + use tcss_usb3_port2 as dfp[0].typec_port + device generic 0 on end + end + chip drivers/intel/usb4/retimer + register "dfp[1].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B21)" + use tcss_usb3_port3 as dfp[1].typec_port + device generic 0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + use usb2_port1 as usb2_port + use tcss_usb3_port0 as usb3_port + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port2 as usb2_port + use tcss_usb3_port1 as usb3_port + device generic 1 alias conn1 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port3 as usb2_port + use tcss_usb3_port2 as usb3_port + device generic 2 alias conn2 on end + end + chip drivers/intel/pmc_mux/conn + use usb2_port4 as usb2_port + use tcss_usb3_port3 as usb3_port + device generic 3 alias conn3 on end + end + end + end + end + + device ref pcie_rp1 off + # register "pcie_rp[PCIE_RP(1)]" = "{ + # .clk_src = 3, + # .clk_req = 3, + # .flags = PCIE_RP_CLK_REQ_DETECT | PCIE_RP_LTR | PCIE_RP_AER, + # }" + end # Gbe + device ref pcie_rp2 on + register "pcie_rp[PCIE_RP(2)]" = "{ + .clk_src = 5, + .clk_req = 5, + .flags = PCIE_RP_CLK_REQ_DETECT | PCIE_RP_LTR | PCIE_RP_AER, + }" + end # WWAN + device ref pcie_rp3 on + # Enable PCH PCIE x1 slot using CLK 3 + register "pcie_rp[PCIE_RP(3)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_CLK_REQ_DETECT | PCIE_RP_LTR | PCIE_RP_AER, + }" + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A08)" + register "enable_delay_ms" = "100" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D19)" + register "reset_delay_ms" = "20" + register "srcclk_pin" = "2" + device generic 0 on end + end + end # PCIE x1 slot + device ref pcie_rp4 on + register "pcie_rp[PCH_RP(4)]" = "{ + .clk_src = 4, + .clk_req = 4, + .flags = PCIE_RP_CLK_REQ_DETECT | PCIE_RP_LTR | PCIE_RP_AER, + }" + chip soc/intel/common/block/pcie/rtd3 + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A11)" + register "srcclk_pin" = "4" + device pci 00.0 on end + end + end # discrete WLAN + device ref pcie_rp5 on + register "pcie_rp[PCIE_RP(5)]" = "{ + .clk_src = 6, + .clk_req = 6, + .flags = PCIE_RP_CLK_REQ_DETECT | PCIE_RP_LTR | PCIE_RP_AER, + }" + chip soc/intel/common/block/pcie/rtd3 + register "is_storage" = "true" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B10)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B09)" + register "srcclk_pin" = "6" + device generic 0 on end + end + end # Gen4 M.2 SSD + device ref pcie_rp6 off end + device ref pcie_rp7 off end + device ref pcie_rp8 off end + device ref pcie_rp9 on + register "pcie_rp[PCIE_RP(9)]" = "{ + .clk_src = 1, + .clk_req = 1, + .flags = PCIE_RP_CLK_REQ_DETECT | PCIE_RP_LTR | PCIE_RP_AER, + }" + chip soc/intel/common/block/pcie/rtd3 + register "is_storage" = "true" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B16)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E03)" + register "srcclk_pin" = "1" + device generic 0 on end + end + end # Gen5 M.2 SSD / x4 PCIe slot + device ref pcie_rp10 off end + device ref pcie_rp11 on + register "pcie_rp[PCIE_RP(11)]" = "{ + .clk_src = 0, + .clk_req = 0, + .flags = PCIE_RP_CLK_REQ_DETECT | PCIE_RP_LTR | PCIE_RP_AER, + }" + end # x8 CEM slot + + device ref ish off + chip drivers/intel/ish + register "firmware_name" = ""lnlrvp_ish.bin"" + device generic 0 off end + end + end + + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port 1"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port 2"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port 3"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port 4"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port 5"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(5, 1)" + device ref usb2_port5 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port 6"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(6, 1)" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port 7"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(7, 1)" + device ref usb2_port7 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_A16)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port 1"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port 2"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(2, 2)" + device ref usb3_port2 on end + end + end + end + end + + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + register "add_acpi_dma_property" = "true" + register "enable_cnvi_ddr_rfim" = "true" + device generic 0 on end + end + end # CNVi + device ref cnvi_bluetooth on end # CNVi BT + + device ref i2c0 on end + device ref i2c1 on + chip drivers/intel/mipi_camera + register "acpi_hid" = ""OVTIDB10"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM0"" + register "chip_name" = ""Ov 13b10 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + + register "ssdb.vcm_type" = "0x0C" + register "vcm_name" = ""VCM1"" + + register "ssdb.lanes_used" = "4" + register "num_freq_entries" = "1" + register "link_freq[0]" = "560000000" + register "remote_name" = ""IPU0"" + + register "has_power_resource" = "1" + #Controls + register "clk_panel.clks[0].clknum" = "0" + register "clk_panel.clks[0].freq" = "1" #19.2 Mhz + register "gpio_panel.gpio[0].gpio_num" = "GPP_C05" #power_enable + register "gpio_panel.gpio[1].gpio_num" = "GPP_E10" #reset + + #_ON + register "on_seq.ops_cnt" = "4" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 2)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 1)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 1)" + + #_OFF + register "off_seq.ops_cnt" = "3" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 36 on end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "3" + register "acpi_name" = ""VCM1"" + register "chip_name" = ""DW AF VCM"" + register "device_type" = "INTEL_ACPI_CAMERA_VCM" + + register "pr0" = ""\_SB.PCI0.I2C1.CAM0.PRIC"" + register "vcm_compat" = ""dongwoon,dw9714"" + + device i2c 0C on end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "1" + register "acpi_name" = ""NVM1"" + register "chip_name" = ""BRCA016GWZ"" + register "device_type" = "INTEL_ACPI_CAMERA_NVM" + + register "pr0" = ""\_SB.PCI0.I2C1.CAM0.PRIC"" + register "nvm_compat" = ""atmel,24c16"" + + register "nvm_size" = "0x800" + register "nvm_pagesize" = "0x01" + register "nvm_readonly" = "0x01" + register "nvm_width" = "0x08" + + device i2c 50 on end + end + end + device ref i2c2 on + chip drivers/intel/mipi_camera + register "acpi_hid" = ""OVTIDB10"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM1"" + register "chip_name" = ""Ov 13b10 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + + register "ssdb.vcm_type" = "0x0C" + register "vcm_name" = ""VCM1"" + + register "ssdb.lanes_used" = "2" + register "num_freq_entries" = "1" + register "link_freq[0]" = "560000000" + register "remote_name" = ""IPU0"" + + register "has_power_resource" = "1" + #Controls + register "clk_panel.clks[0].clknum" = "1" + register "clk_panel.clks[0].freq" = "1" #19.2 Mhz + register "gpio_panel.gpio[0].gpio_num" = "GPP_C08" #power_enable + register "gpio_panel.gpio[1].gpio_num" = "GPP_E01" #reset + + #_ON + register "on_seq.ops_cnt" = "4" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 2)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 1)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_ENABLE(1, 1)" + + #_OFF + register "off_seq.ops_cnt" = "3" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 36 on end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "3" + register "acpi_name" = ""VCM1"" + register "chip_name" = ""DW AF VCM"" + register "device_type" = "INTEL_ACPI_CAMERA_VCM" + + register "pr0" = ""\_SB.PCI0.I2C2.CAM1.PRIC"" + register "vcm_compat" = ""dongwoon,dw9714"" + + device i2c 0C on end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "1" + register "acpi_name" = ""NVM1"" + register "chip_name" = ""BRCA016GWZ"" + register "device_type" = "INTEL_ACPI_CAMERA_NVM" + + register "pr0" = ""\_SB.PCI0.I2C2.CAM1.PRIC"" + register "nvm_compat" = ""atmel,24c16"" + + register "nvm_size" = "0x800" + register "nvm_pagesize" = "0x01" + register "nvm_readonly" = "0x01" + register "nvm_width" = "0x08" + + device i2c 50 on end + end + end + device ref i2c3 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F17)" + register "probed" = "1" + # jd_src RT5668_JD1 = 1, RT5682_JD_NULL = 0 + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_F17)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on end + end + + # Ref config #5 for Chrome, transducer card config 5A + #+-------------------+-------------------+ + #| Speaker Amp | Assignment | + #+-------------------+-------------------+ + #| SPK 0 | left | + #| SPK 1 | right | + #| SPK 2 | top left | + #| SPK 3 | top right | + #+-------------------+-------------------+ + chip drivers/i2c/generic + register "hid" = ""10EC1019"" + register "desc" = ""Realtek SPK AMP L"" + register "uid" = "0" + device i2c 28 on end + end + chip drivers/i2c/generic + register "hid" = ""10EC1019"" + register "desc" = ""Realtek SPK AMP R"" + register "uid" = "1" + device i2c 29 on end + end + chip drivers/i2c/generic + register "hid" = ""10EC1019"" + register "desc" = ""Realtek SPK AMP TL"" + register "uid" = "2" + device i2c 2a on end + end + chip drivers/i2c/generic + register "hid" = ""10EC1019"" + register "desc" = ""Realtek SPK AMP TR"" + register "uid" = "3" + device i2c 2b on end + end + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_D15_IRQ)" + device i2c 50 on end + end + end #i2c3 + device ref i2c4 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN6918"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E18_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E16)" + register "generic.reset_delay_ms" = "20" + register "generic.reset_off_delay_ms" = "2" + register "generic.enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_F08)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 16 on end + end + end + device ref i2c5 on + chip drivers/i2c/hid + register "generic.hid" = ""HFW68H"" + register "generic.desc" = ""Hynitron TOUCHPAD"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F18_IRQ)" + register "generic.uid" = "5" + register "generic.detect" = "1" + register "hid_desc_reg_offset" = "0x20" + device i2c 2c on end + end + end # i2c5 + + device ref uart0 on end + device ref uart1 off end + device ref uart2 off end + + device ref gspi0 on end + device ref gspi1 on end + + device ref smbus on end + device ref gbe off end + device ref npk on end + device ref soc_espi on + chip ec/google/chromeec + device pnp 0c09.0 on end + end + end + device ref hda on + chip drivers/intel/soundwire + device generic 0 on + chip drivers/soundwire/alc711 + # SoundWire Link 1 ID 1 + register "desc" = ""Headset Codec"" + device generic 1.1 on end + end + end + end + chip drivers/generic/max98357a + register "hid" = ""MX98357A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E19)" + register "sdmode_delay" = "5" + device generic 0 on end + end + chip drivers/generic/max98357a + register "hid" = ""MX98360A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E19)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end + + end +end
-
Jérémy Compostella (Code Review)