[coreboot-gerrit] Change in coreboot[master]: nipperkin: Set eSPI alert as dedicated open drain

[Rob Barnes (Code Review)]

Rob Barnes has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/57313 )

Change subject: nipperkin: Set eSPI alert as dedicated open drain
......................................................................

nipperkin: Set eSPI alert as dedicated open drain

Nipperkin boards use a dedicated eSPI alert#. Must be open drain to
prevent power leaks.

BUG=b:198409370
TEST=Build nipperkin
BRANCH=None

Change-Id: I4b23bfc6a1167aebfde5acd524fda043b63163dc
Signed-off-by: Rob Barnes 
---
M src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
1 file changed, 39 insertions(+), 0 deletions(-)

git pull ssh://review.coreboot.org:29418/coreboot refs/changes/13/57313/1

diff --git a/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb b/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
index c182265..6b6be7e 100644
--- a/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
+++ b/src/mainboard/google/guybrush/variants/nipperkin/overridetree.cb
@@ -4,4 +4,43 @@
    device domain 0 on

end # domain
+
+	# eSPI Configuration
+	register "common_config.espi_config" = "{
+		.std_io_decode_bitmap = ESPI_DECODE_IO_0x80_EN | ESPI_DECODE_IO_0X60_0X64_EN,
+		.generic_io_range[0] = {
+			.base = 0x62,
+			/*
+			 * Only 0x62 and 0x66 are required. But, this is not supported by
+			 * standard IO decodes and there are only 4 generic I/O windows
+			 * available. Hence, open a window from 0x62-0x67.
+			 */
+			.size = 5,
+		},
+		.generic_io_range[1] = {
+			.base = 0x800,   /* EC_HOST_CMD_REGION0 */
+			.size = 256,     /* EC_HOST_CMD_REGION_SIZE * 2 */
+		},
+		.generic_io_range[2] = {
+			.base = 0x900,   /* EC_LPC_ADDR_MEMMAP */
+			.size = 255,     /* EC_MEMMAP_SIZE */
+		},
+		.generic_io_range[3] = {
+			.base = 0x200,   /* EC_LPC_ADDR_HOST_DATA */
+			.size = 8,       /* 0x200 - 0x207 */
+		},
+
+		.io_mode = ESPI_IO_MODE_QUAD,
+		.op_freq_mhz = ESPI_OP_FREQ_33_MHZ,
+		.crc_check_enable = 1,
+
+		.alert_pin = ESPI_ALERT_PIN_OPEN_DRAIN,
+		.periph_ch_en = 1,
+		.vw_ch_en = 1,
+		.oob_ch_en = 0,
+		.flash_ch_en = 0,
+
+		.vw_irq_polarity = ESPI_VW_IRQ_LEVEL_HIGH(1),
+	}"
+
 end	# chip soc/amd/cezanne