Tim Wawrzynczak has submitted this change. ( https://review.coreboot.org/c/coreboot/+/59728 )
Change subject: brya: add various ES variants ......................................................................
brya: add various ES variants
Fork multiple "4ES" variants off some brya devices to properly support ES SoC.
BRANCH=none BUG=b:201767461 TEST=emerge-brya coreboot and check the artifacts
Signed-off-by: YH Lin yueherngl@google.com Change-Id: Ic9516fec591429238bde1478eca2522d8ed10127 Reviewed-on: https://review.coreboot.org/c/coreboot/+/59728 Tested-by: build bot (Jenkins) no-reply@coreboot.org Reviewed-by: Tim Wawrzynczak twawrzynczak@chromium.org --- M src/mainboard/google/brya/Kconfig M src/mainboard/google/brya/Kconfig.name A src/mainboard/google/brya/variants/anahera4es/Makefile.inc A src/mainboard/google/brya/variants/anahera4es/fw_config.c A src/mainboard/google/brya/variants/anahera4es/gpio.c A src/mainboard/google/brya/variants/anahera4es/include/variant/ec.h A src/mainboard/google/brya/variants/anahera4es/include/variant/gpio.h A src/mainboard/google/brya/variants/anahera4es/memory/Makefile.inc A src/mainboard/google/brya/variants/anahera4es/memory/dram_id.generated.txt A src/mainboard/google/brya/variants/anahera4es/memory/mem_parts_used.txt A src/mainboard/google/brya/variants/anahera4es/overridetree.cb A src/mainboard/google/brya/variants/brya4es/Makefile.inc A src/mainboard/google/brya/variants/brya4es/fw_config.c A src/mainboard/google/brya/variants/brya4es/gpio.c A src/mainboard/google/brya/variants/brya4es/include/variant/ec.h A src/mainboard/google/brya/variants/brya4es/include/variant/gpio.h A src/mainboard/google/brya/variants/brya4es/memory/Makefile.inc A src/mainboard/google/brya/variants/brya4es/memory/dram_id.generated.txt A src/mainboard/google/brya/variants/brya4es/memory/mem_parts_used.txt A src/mainboard/google/brya/variants/brya4es/overridetree.cb A src/mainboard/google/brya/variants/brya4es/ramstage.c A src/mainboard/google/brya/variants/brya4es/variant.c A src/mainboard/google/brya/variants/gimble4es/Makefile.inc A src/mainboard/google/brya/variants/gimble4es/fw_config.c A src/mainboard/google/brya/variants/gimble4es/gpio.c A src/mainboard/google/brya/variants/gimble4es/include/variant/ec.h A src/mainboard/google/brya/variants/gimble4es/include/variant/gpio.h A src/mainboard/google/brya/variants/gimble4es/memory/Makefile.inc A src/mainboard/google/brya/variants/gimble4es/memory/dram_id.generated.txt A src/mainboard/google/brya/variants/gimble4es/memory/mem_parts_used.txt A src/mainboard/google/brya/variants/gimble4es/overridetree.cb A src/mainboard/google/brya/variants/gimble4es/variant.c A src/mainboard/google/brya/variants/primus4es/Makefile.inc A src/mainboard/google/brya/variants/primus4es/fw_config.c A src/mainboard/google/brya/variants/primus4es/gpio.c A src/mainboard/google/brya/variants/primus4es/include/variant/ec.h A src/mainboard/google/brya/variants/primus4es/include/variant/gpio.h A src/mainboard/google/brya/variants/primus4es/memory/Makefile.inc A src/mainboard/google/brya/variants/primus4es/memory/dram_id.generated.txt A src/mainboard/google/brya/variants/primus4es/memory/mem_parts_used.txt A src/mainboard/google/brya/variants/primus4es/overridetree.cb A src/mainboard/google/brya/variants/primus4es/variant.c A src/mainboard/google/brya/variants/redrix4es/Makefile.inc A src/mainboard/google/brya/variants/redrix4es/fw_config.c A src/mainboard/google/brya/variants/redrix4es/gpio.c A src/mainboard/google/brya/variants/redrix4es/include/variant/ec.h A src/mainboard/google/brya/variants/redrix4es/include/variant/gpio.h A src/mainboard/google/brya/variants/redrix4es/memory/Makefile.inc A src/mainboard/google/brya/variants/redrix4es/memory/dram_id.generated.txt A src/mainboard/google/brya/variants/redrix4es/memory/mem_parts_used.txt A src/mainboard/google/brya/variants/redrix4es/overridetree.cb A src/mainboard/google/brya/variants/redrix4es/variant.c A src/mainboard/google/brya/variants/taeko4es/Makefile.inc A src/mainboard/google/brya/variants/taeko4es/fw_config.c A src/mainboard/google/brya/variants/taeko4es/gpio.c A src/mainboard/google/brya/variants/taeko4es/include/variant/ec.h A src/mainboard/google/brya/variants/taeko4es/include/variant/gpio.h A src/mainboard/google/brya/variants/taeko4es/memory.c A src/mainboard/google/brya/variants/taeko4es/memory/Makefile.inc A src/mainboard/google/brya/variants/taeko4es/memory/dram_id.generated.txt A src/mainboard/google/brya/variants/taeko4es/memory/mem_parts_used.txt A src/mainboard/google/brya/variants/taeko4es/overridetree.cb 62 files changed, 4,936 insertions(+), 0 deletions(-)
Approvals: build bot (Jenkins): Verified Tim Wawrzynczak: Looks good to me, approved
diff --git a/src/mainboard/google/brya/Kconfig b/src/mainboard/google/brya/Kconfig index 6231762..a5ca942 100644 --- a/src/mainboard/google/brya/Kconfig +++ b/src/mainboard/google/brya/Kconfig @@ -104,26 +104,38 @@
config MAINBOARD_PART_NUMBER default "Brya" if BOARD_GOOGLE_BRYA0 + default "Brya4ES" if BOARD_GOOGLE_BRYA4ES default "Brask" if BOARD_GOOGLE_BRASK default "Primus" if BOARD_GOOGLE_PRIMUS + default "Primus4ES" if BOARD_GOOGLE_PRIMUS4ES default "Gimble" if BOARD_GOOGLE_GIMBLE + default "Gimble4ES" if BOARD_GOOGLE_GIMBLE4ES default "Redrix" if BOARD_GOOGLE_REDRIX + default "Redrix4ES" if BOARD_GOOGLE_REDRIX4ES default "Kano" if BOARD_GOOGLE_KANO default "Taeko" if BOARD_GOOGLE_TAEKO + default "Taeko4ES" if BOARD_GOOGLE_TAEKO4ES default "Felwinter" if BOARD_GOOGLE_FELWINTER default "Anahera" if BOARD_GOOGLE_ANAHERA + default "Anahera4ES" if BOARD_GOOGLE_ANAHERA4ES default "Vell" if BOARD_GOOGLE_VELL
config VARIANT_DIR default "brya0" if BOARD_GOOGLE_BRYA0 + default "brya4es" if BOARD_GOOGLE_BRYA4ES default "brask" if BOARD_GOOGLE_BRASK default "primus" if BOARD_GOOGLE_PRIMUS + default "primus4es" if BOARD_GOOGLE_PRIMUS4ES default "gimble" if BOARD_GOOGLE_GIMBLE + default "gimble4es" if BOARD_GOOGLE_GIMBLE4ES default "redrix" if BOARD_GOOGLE_REDRIX + default "redrix4es" if BOARD_GOOGLE_REDRIX4ES default "kano" if BOARD_GOOGLE_KANO default "taeko" if BOARD_GOOGLE_TAEKO + default "taeko4es" if BOARD_GOOGLE_TAEKO4ES default "felwinter" if BOARD_GOOGLE_FELWINTER default "anahera" if BOARD_GOOGLE_ANAHERA + default "anahera4es" if BOARD_GOOGLE_ANAHERA4ES default "vell" if BOARD_GOOGLE_VELL
config VBOOT diff --git a/src/mainboard/google/brya/Kconfig.name b/src/mainboard/google/brya/Kconfig.name index 92b71a8..8041171 100644 --- a/src/mainboard/google/brya/Kconfig.name +++ b/src/mainboard/google/brya/Kconfig.name @@ -10,6 +10,16 @@ select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES select SOC_INTEL_CRASHLOG
+config BOARD_GOOGLE_BRYA4ES + bool "-> Brya4ES" + select BOARD_GOOGLE_BASEBOARD_BRYA + select DRIVERS_GENESYSLOGIC_GL9755 + select DRIVERS_INTEL_MIPI_CAMERA + select HAVE_WWAN_POWER_SEQUENCE + select SOC_INTEL_COMMON_BLOCK_IPU + select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES + select SOC_INTEL_CRASHLOG + config BOARD_GOOGLE_BRASK bool "-> Brask" select BOARD_GOOGLE_BASEBOARD_BRASK @@ -24,6 +34,13 @@ select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES select HAVE_WWAN_POWER_SEQUENCE
+config BOARD_GOOGLE_PRIMUS4ES + bool "-> Primus4ES" + select BOARD_GOOGLE_BASEBOARD_BRYA + select DRIVERS_GENESYSLOGIC_GL9755 + select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES + select HAVE_WWAN_POWER_SEQUENCE + config BOARD_GOOGLE_GIMBLE bool "-> Gimble" select BOARD_GOOGLE_BASEBOARD_BRYA @@ -32,6 +49,14 @@ select DRIVERS_GENESYSLOGIC_GL9750 select DRIVERS_I2C_MAX98390
+config BOARD_GOOGLE_GIMBLE4ES + bool "-> Gimble4ES" + select BOARD_GOOGLE_BASEBOARD_BRYA + select CHROMEOS_DSM_CALIB if CHROMEOS + select CHROMEOS_DSM_PARAM_FILE_NAME if CHROMEOS + select DRIVERS_GENESYSLOGIC_GL9750 + select DRIVERS_I2C_MAX98390 + config BOARD_GOOGLE_REDRIX bool "-> Redrix" select BOARD_GOOGLE_BASEBOARD_BRYA @@ -46,6 +71,20 @@ select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES select HAVE_WWAN_POWER_SEQUENCE
+config BOARD_GOOGLE_REDRIX4ES + bool "-> Redrix4ES" + select BOARD_GOOGLE_BASEBOARD_BRYA + select CHROMEOS_DSM_CALIB if CHROMEOS + select CHROMEOS_DSM_PARAM_FILE_NAME if CHROMEOS + select DRIVERS_I2C_MAX98390 + select DRIVERS_INTEL_MIPI_CAMERA + select EC_GOOGLE_CHROMEEC_INCLUDE_SSFC_IN_FW_CONFIG + select SOC_INTEL_COMMON_BLOCK_IPU + select DRIVERS_GENESYSLOGIC_GL9755 + select DRIVERS_GFX_GENERIC + select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES + select HAVE_WWAN_POWER_SEQUENCE + config BOARD_GOOGLE_KANO bool "-> Kano" select BOARD_GOOGLE_BASEBOARD_BRYA @@ -60,6 +99,11 @@ select BOARD_GOOGLE_BASEBOARD_BRYA select DRIVERS_GENESYSLOGIC_GL9763E
+config BOARD_GOOGLE_TAEKO4ES + bool "-> Taeko4ES" + select BOARD_GOOGLE_BASEBOARD_BRYA + select DRIVERS_GENESYSLOGIC_GL9763E + config BOARD_GOOGLE_FELWINTER bool "-> Felwinter" select BOARD_GOOGLE_BASEBOARD_BRYA @@ -72,6 +116,13 @@ select DRIVERS_GFX_GENERIC select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES
+config BOARD_GOOGLE_ANAHERA4ES + bool "-> Anahera4ES" + select BOARD_GOOGLE_BASEBOARD_BRYA + select DRIVERS_GENESYSLOGIC_GL9763E + select DRIVERS_GFX_GENERIC + select SOC_INTEL_ENABLE_USB4_PCIE_RESOURCES + config BOARD_GOOGLE_VELL bool "-> Vell" select BOARD_GOOGLE_BASEBOARD_BRYA diff --git a/src/mainboard/google/brya/variants/anahera4es/Makefile.inc b/src/mainboard/google/brya/variants/anahera4es/Makefile.inc new file mode 100644 index 0000000..f2a624c --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/Makefile.inc @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0-only +bootblock-y += gpio.c + +ramstage-y += gpio.c + +ramstage-$(CONFIG_FW_CONFIG) += fw_config.c diff --git a/src/mainboard/google/brya/variants/anahera4es/fw_config.c b/src/mainboard/google/brya/variants/anahera4es/fw_config.c new file mode 100644 index 0000000..b12293f --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/fw_config.c @@ -0,0 +1,57 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <fw_config.h> +#include <gpio.h> + +static const struct pad_config dmic_enable_pads[] = { + PAD_CFG_NF(GPP_R4, NONE, DEEP, NF3), /* DMIC_CLK0 */ + PAD_CFG_NF(GPP_R5, NONE, DEEP, NF3), /* DMIC_DATA0 */ + +}; + +static const struct pad_config dmic_disable_pads[] = { + PAD_NC(GPP_R4, NONE), + PAD_NC(GPP_R5, NONE), +}; + +static const struct pad_config i2s_enable_pads[] = { + PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK */ + PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM */ + PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */ + PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */ + PAD_CFG_NF(GPP_S0, NONE, DEEP, NF4), /* I2S_SPKR_SCLK */ + PAD_CFG_NF(GPP_S1, NONE, DEEP, NF4), /* I2S_SPKR_SFRM */ + PAD_CFG_NF(GPP_S2, NONE, DEEP, NF4), /* I2S_PCH_TX_SPKR_RX */ + PAD_CFG_NF(GPP_S3, NONE, DEEP, NF4), /* I2S_PCH_RX_SPKR_TX */ +}; + +static const struct pad_config i2s_disable_pads[] = { + PAD_NC(GPP_R0, NONE), + PAD_NC(GPP_R1, NONE), + PAD_NC(GPP_R2, NONE), + PAD_NC(GPP_R3, NONE), + PAD_NC(GPP_S0, NONE), + PAD_NC(GPP_S1, NONE), + PAD_NC(GPP_S2, NONE), + PAD_NC(GPP_S3, NONE), +}; + +static void fw_config_handle(void *unused) +{ + if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) { + printk(BIOS_INFO, "Disable audio related GPIO pins.\n"); + gpio_configure_pads(i2s_disable_pads, ARRAY_SIZE(i2s_disable_pads)); + gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads)); + return; + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98360_ALC5682I_I2S)) || + fw_config_probe(FW_CONFIG(AUDIO, MAX98360_ALC5682IVS_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98390 ALC5682I.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + } +} +BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL); diff --git a/src/mainboard/google/brya/variants/anahera4es/gpio.c b/src/mainboard/google/brya/variants/anahera4es/gpio.c new file mode 100644 index 0000000..4ab457b --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/gpio.c @@ -0,0 +1,147 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/gpio.h> +#include <baseboard/variants.h> +#include <commonlib/helpers.h> +#include <soc/gpio.h> + +/* Pad configuration in ramstage */ +static const struct pad_config override_gpio_table[] = { + /* A7 : SRCCLK_OE7# ==> NC */ + PAD_NC(GPP_A7, NONE), + /* A17 : DISP_MISCC ==> NC */ + PAD_NC(GPP_A17, NONE), + /* A19 : DDSP_HPD1 ==> NC */ + PAD_NC(GPP_A19, NONE), + /* A20 : DDSP_HPD2 ==> NC */ + PAD_NC(GPP_A20, NONE), + /* A21 : DDPC_CTRCLK ==> NC */ + PAD_NC(GPP_A21, NONE), + /* A22 : DDPC_CTRLDATA ==> NC */ + PAD_NC(GPP_A22, NONE), + + /* B3 : PROC_GP2 ==> eMMC_PERST_L */ + PAD_CFG_GPO(GPP_B3, 1, DEEP), + /* B5 : ISH_I2C0_SDA ==> NC */ + PAD_NC(GPP_B5, NONE), + /* B6 : ISH_I2C0_SCL ==> NC */ + PAD_NC(GPP_B6, NONE), + /* B15 : TIME_SYNC0 ==> NC */ + PAD_NC(GPP_B15, NONE), + + /* C3 : SML0CLK ==> NC */ + PAD_NC(GPP_C3, NONE), + /* C4 : SML0DATA ==> NC */ + PAD_NC(GPP_C4, NONE), + + /* D3 : ISH_GP3 ==> NC */ + PAD_NC(GPP_D3, NONE), + /* D5 : SRCCLKREQ0# ==> NC */ + PAD_NC(GPP_D5, NONE), + /* D7 : SRCCLKREQ2# ==> NC */ + PAD_NC(GPP_D7, NONE), + /* D13 : ISH_UART0_RXD ==> NC */ + PAD_NC(GPP_D13, NONE), + /* D14 : ISH_UART0_TXD ==> NC */ + PAD_NC(GPP_D14, NONE), + /* D15 : ISH_UART0_RTS# ==> EN_WCAM_SENR_PWR */ + PAD_CFG_GPO(GPP_D15, 1, DEEP), + /* D16 : ISH_UART0_CTS# ==> NC */ + PAD_NC(GPP_D16, NONE), + /* D17 : UART1_RXD ==> NC */ + PAD_NC(GPP_D17, NONE), + + /* E0 : SATAXPCIE0 ==> WWAN_PERST_L */ + PAD_CFG_GPO(GPP_E0, 1, PLTRST), + /* E3 : PROC_GP0 ==> NC */ + PAD_NC(GPP_E3, NONE), + /* E7 : PROC_GP1 ==> NC */ + PAD_NC(GPP_E7, NONE), + /* F19 : SRCCLKREQ6# ==> EMMC_CLKREQ_ODL */ + PAD_CFG_NF(GPP_F19, NONE, DEEP, NF1), + + /* E20 : USB_C1_LSX_SOC_TX ==> EN_PP3300_eMMC */ + PAD_CFG_GPO(GPP_E20, 1, DEEP), + /* E23 : DDPA_CTRLDATA ==> NC */ + PAD_NC(GPP_E23, NONE), + + /* F20 : EXT_PWR_GATE# ==> NC */ + PAD_NC(GPP_F20, NONE), + + /* H20 : IMGCLKOUT1 ==> NC */ + PAD_NC(GPP_H20, NONE), + /* H21 : IMGCLKOUT2 ==> Privacy screen */ + PAD_CFG_GPO(GPP_H21, 0, DEEP), + /* H22 : IMGCLKOUT3 ==> NC */ + PAD_NC(GPP_H22, NONE), + /* H23 : SRCCLKREQ5# ==> NC */ + PAD_NC(GPP_H23, NONE), + + /* R6 : I2S_PCH_TX_SPKR_RX ==> NC */ + PAD_NC(GPP_R6, NONE), + /* R7 : I2S_PCH_RX_SPKR_TX ==> NC */ + PAD_NC(GPP_R7, NONE), + + /* S4 : SNDW2_CLK ==> NC */ + PAD_NC(GPP_S4, NONE), + /* S5 : SNDW2_DATA ==> NC */ + PAD_NC(GPP_S5, NONE), + /* S6 : SNDW3_CLK ==> NC */ + PAD_NC(GPP_S6, NONE), + /* S7 : SNDW3_DATA ==> NC */ + PAD_NC(GPP_S7, NONE), + +}; + +/* Early pad configuration in bootblock */ +static const struct pad_config early_gpio_table[] = { + /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */ + PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT), + /* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */ + PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2), + /* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */ + PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2), + /* + * D1 : ISH_GP1 ==> FP_RST_ODL + * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down. + * To ensure proper power sequencing for the FPMCU device, reset signal is driven low + * early on in bootblock, followed by enabling of power. Reset signal is deasserted + * later on in ramstage. Since reset signal is asserted in bootblock, it results in + * FPMCU not working after a S3 resume. This is a known issue. + */ + PAD_CFG_GPO(GPP_D1, 0, DEEP), + /* D2 : ISH_GP2 ==> EN_FP_PWR */ + PAD_CFG_GPO(GPP_D2, 1, DEEP), + /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */ + PAD_CFG_GPO(GPP_D11, 1, DEEP), + /* E0 : SATAXPCIE0 ==> WWAN_PERST_L */ + PAD_CFG_GPO(GPP_E0, 0, DEEP), + /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */ + PAD_CFG_GPI(GPP_E13, NONE, DEEP), + /* E15 : RSVD_TP ==> PCH_WP_OD */ + PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP), + /* E16 : RSVD_TP ==> WWAN_RST_L */ + PAD_CFG_GPO(GPP_E16, 0, DEEP), + /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */ + PAD_CFG_GPI(GPP_F18, NONE, DEEP), + /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */ + PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2), + /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */ + PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2), + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_CFG_GPO(GPP_H13, 1, DEEP), + /* E20 : USB_C1_LSX_SOC_TX ==> EN_PP3300_MMC */ + PAD_CFG_GPO(GPP_E20, 1, DEEP), +}; + +const struct pad_config *variant_gpio_override_table(size_t *num) +{ + *num = ARRAY_SIZE(override_gpio_table); + return override_gpio_table; +} + +const struct pad_config *variant_early_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(early_gpio_table); + return early_gpio_table; +} diff --git a/src/mainboard/google/brya/variants/anahera4es/include/variant/ec.h b/src/mainboard/google/brya/variants/anahera4es/include/variant/ec.h new file mode 100644 index 0000000..7a2a6ff --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/include/variant/ec.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __VARIANT_EC_H__ +#define __VARIANT_EC_H__ + +#include <baseboard/ec.h> + +#endif diff --git a/src/mainboard/google/brya/variants/anahera4es/include/variant/gpio.h b/src/mainboard/google/brya/variants/anahera4es/include/variant/gpio.h new file mode 100644 index 0000000..c4fe342 --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/include/variant/gpio.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef VARIANT_GPIO_H +#define VARIANT_GPIO_H + +#include <baseboard/gpio.h> + +#endif diff --git a/src/mainboard/google/brya/variants/anahera4es/memory/Makefile.inc b/src/mainboard/google/brya/variants/anahera4es/memory/Makefile.inc new file mode 100644 index 0000000..68aa2f0 --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/memory/Makefile.inc @@ -0,0 +1,11 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/anahera/memory src/mainboard/google/brya/variants/anahera/memory/mem_parts_used.txt + +SPD_SOURCES = +SPD_SOURCES += spd/lp4x/set-0/spd-4.hex # ID = 0(0b0000) Parts = MT53E1G32D2NP-046 WT:A +SPD_SOURCES += spd/lp4x/set-0/spd-1.hex # ID = 1(0b0001) Parts = H9HCNNNBKMMLXR-NEE, K4U6E3S4AA-MGCR, MT53E512M32D2NP-046 WT:E, MT53E512M32D1NP-046 WT:B +SPD_SOURCES += spd/lp4x/set-0/spd-3.hex # ID = 2(0b0010) Parts = H9HCNNNCPMMLXR-NEE, K4UBE3D4AA-MGCR, MT53E1G32D2NP-046 WT:B +SPD_SOURCES += spd/lp4x/set-0/spd-2.hex # ID = 3(0b0011) Parts = H9HCNNNFAMMLXR-NEE +SPD_SOURCES += spd/lp4x/set-0/spd-7.hex # ID = 4(0b0100) Parts = MT53E2G32D4NQ-046 WT:A diff --git a/src/mainboard/google/brya/variants/anahera4es/memory/dram_id.generated.txt b/src/mainboard/google/brya/variants/anahera4es/memory/dram_id.generated.txt new file mode 100644 index 0000000..dcc5ba3 --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/memory/dram_id.generated.txt @@ -0,0 +1,16 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/anahera/memory src/mainboard/google/brya/variants/anahera/memory/mem_parts_used.txt + +DRAM Part Name ID to assign +MT53E1G32D2NP-046 WT:A 0 (0000) +H9HCNNNBKMMLXR-NEE 1 (0001) +K4U6E3S4AA-MGCR 1 (0001) +MT53E512M32D2NP-046 WT:E 1 (0001) +H9HCNNNCPMMLXR-NEE 2 (0010) +K4UBE3D4AA-MGCR 2 (0010) +H9HCNNNFAMMLXR-NEE 3 (0011) +MT53E2G32D4NQ-046 WT:A 4 (0100) +MT53E512M32D1NP-046 WT:B 1 (0001) +MT53E1G32D2NP-046 WT:B 2 (0010) diff --git a/src/mainboard/google/brya/variants/anahera4es/memory/mem_parts_used.txt b/src/mainboard/google/brya/variants/anahera4es/memory/mem_parts_used.txt new file mode 100644 index 0000000..71bd5fd --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/memory/mem_parts_used.txt @@ -0,0 +1,10 @@ +MT53E1G32D2NP-046 WT:A +H9HCNNNBKMMLXR-NEE +K4U6E3S4AA-MGCR +MT53E512M32D2NP-046 WT:E +H9HCNNNCPMMLXR-NEE +K4UBE3D4AA-MGCR +H9HCNNNFAMMLXR-NEE +MT53E2G32D4NQ-046 WT:A +MT53E512M32D1NP-046 WT:B +MT53E1G32D2NP-046 WT:B diff --git a/src/mainboard/google/brya/variants/anahera4es/overridetree.cb b/src/mainboard/google/brya/variants/anahera4es/overridetree.cb new file mode 100644 index 0000000..dc563a4 --- /dev/null +++ b/src/mainboard/google/brya/variants/anahera4es/overridetree.cb @@ -0,0 +1,378 @@ +fw_config + field DB_SD 0 1 + option SD_ABSENT 0 + option SD_GL9750 1 + end + field KB_BL 2 2 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field AUDIO 3 5 + option AUDIO_UNKNOWN 0 + option MAX98360_ALC5682I_I2S 1 + option MAX98360_ALC5682IVS_I2S 2 + end + field DB_LTE 6 7 + option LTE_ABSENT 0 + option LTE_USB 1 + end + field EPS 10 10 + option PRIVACY_SCREEN_ABSENT 0 + option PRIVACY_SCREEN 1 + end +end +chip soc/intel/alderlake + # This disables autonomous GPIO power management, otherwise + # old cr50 FW only supports short pulses; need to clarify + # the minimum PCH IRQ pulse width with Intel, b/180111628 + register "gpio_override_pm" = "1" + register "gpio_pm[COMM_0]" = "0" + register "gpio_pm[COMM_1]" = "0" + register "gpio_pm[COMM_2]" = "0" + register "gpio_pm[COMM_3]" = "0" + register "gpio_pm[COMM_4]" = "0" + register "gpio_pm[COMM_5]" = "0" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI1 | Fingerprint MCU | + #| I2C0 | Audio | + #| I2C1 | Touchscreen | + #| I2C2 | | + #| I2C3 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[3] = { + .early_init = 1, + .speed = I2C_SPEED_FAST, + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + }, + }" + register "usb2_ports[1]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MLB Port + register "usb2_ports[6]" = "USB2_PORT_MID(OC_SKIP)" # Smart Card + register "usb3_ports[2]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port + device domain 0 on + device ref igpu on + chip drivers/gfx/generic + register "device_count" = "1" + register "device[0].name" = ""LCD"" + # Internal panel on the first port of the graphics chip + register "device[0].addr" = "0x80010400" + register "device[0].privacy.enabled" = "1" + register "device[0].privacy.gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H21)" + device generic 0 on + probe EPS PRIVACY_SCREEN + end + end + end # Integrated Graphics Device + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DRAM"" + register "options.tsr[1].desc" = ""Soc"" + register "options.tsr[2].desc" = ""Charger"" + register "options.tsr[3].desc" = ""Regulator"" + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 5000), + [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 75, 5000), + }" + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN), + }" + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 3000, + .max_power = 15000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200, + }, + .pl2 = { + .min_power = 55000, + .max_power = 55000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + device generic 0 on end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end + device ref pcie_rp6 off end + device ref pcie_rp7 on + # Enable PCIE eMMC bridge 7 using clk 6 + register "pch_pcie_rp[PCH_RP(7)]" = "{ + .clk_src = 6, + .clk_req = 6, + .flags = PCIE_RP_HOTPLUG | PCIE_RP_AER, + }" + end #PCIE7 EMMC + device ref tcss_dma0 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port1 as dfp[0].typec_port + device generic 0 on end + end + end + device ref tcss_dma1 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port3 as dfp[0].typec_port + device generic 0 on end + end + end + device ref pcie_rp8 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" + register "srcclk_pin" = "3" + device generic 0 on end + end + end #PCIE8 SD card + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO MAX98360_ALC5682I_I2S + end + end + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO MAX98360_ALC5682IVS_I2S + end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "probed" = "1" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "reset_delay_ms" = "100" + register "reset_off_delay_ms" = "5" + register "enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "enable_delay_ms" = "10" + register "enable_off_delay_ms" = "1" + register "stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "has_power_resource" = "1" + device i2c 10 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""GTCH7503"" + register "generic.desc" = ""G2TOUCH Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "50" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 40 on end + end + end + device ref i2c3 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on end + end + end + device ref hda on + chip drivers/generic/max98357a + register "hid" = ""MX98360A"" + register "sdmode_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + register "sdmode_delay" = "5" + device generic 0 on end + end + end + device ref gspi1 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" + register "wake" = "GPE0_DW2_15" + device spi 0 on end + end # FPMCU + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "1" + register "usb3_port_number" = "1" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "3" + register "usb3_port_number" = "3" + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C2 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 2)" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C2 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port (DB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port9 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(4, 2)" + device ref usb3_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port4 on end + end + end + end + end + end +end diff --git a/src/mainboard/google/brya/variants/brya4es/Makefile.inc b/src/mainboard/google/brya/variants/brya4es/Makefile.inc new file mode 100644 index 0000000..52d0398 --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/Makefile.inc @@ -0,0 +1,6 @@ +bootblock-y += gpio.c +romstage-y += gpio.c +ramstage-$(CONFIG_FW_CONFIG) += fw_config.c +ramstage-$(CONFIG_FW_CONFIG) += variant.c +ramstage-y += gpio.c +ramstage-y += ramstage.c diff --git a/src/mainboard/google/brya/variants/brya4es/fw_config.c b/src/mainboard/google/brya/variants/brya4es/fw_config.c new file mode 100644 index 0000000..17d284a --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/fw_config.c @@ -0,0 +1,130 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <fw_config.h> +#include <gpio.h> + +static const struct pad_config dmic_enable_pads[] = { + PAD_CFG_NF(GPP_S2, NONE, DEEP, NF2), /* DMIC_CLK0_R */ + PAD_CFG_NF(GPP_S3, NONE, DEEP, NF2), /* DMIC_DATA0_R */ + PAD_CFG_NF(GPP_S6, NONE, DEEP, NF2), /* DMIC_CLK1_R */ + PAD_CFG_NF(GPP_S7, NONE, DEEP, NF2), /* DMIC_DATA1_R */ +}; + +static const struct pad_config dmic_disable_pads[] = { + PAD_NC(GPP_S2, NONE), + PAD_NC(GPP_S3, NONE), + PAD_NC(GPP_S6, NONE), + PAD_NC(GPP_S7, NONE), +}; + +static const struct pad_config sndw_enable_pads[] = { + PAD_CFG_NF(GPP_S0, NONE, DEEP, NF1), /* SDW_HP_CLK_R */ + PAD_CFG_NF(GPP_S1, NONE, DEEP, NF1), /* SDW_HP_DATA_R */ + PAD_CFG_NF(GPP_S4, NONE, DEEP, NF1), /* SDW_SPKR_CLK */ + PAD_CFG_NF(GPP_S5, NONE, DEEP, NF1), /* SDW_SPKR_DATA */ +}; + +static const struct pad_config sndw_disable_pads[] = { + PAD_NC(GPP_S0, NONE), + PAD_NC(GPP_S1, NONE), + PAD_NC(GPP_S4, NONE), + PAD_NC(GPP_S5, NONE), +}; + +static const struct pad_config i2s0_enable_pads[] = { + PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK_R */ + PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM_R */ + PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */ + PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */ +}; + +static const struct pad_config i2s2_enable_pads[] = { + PAD_CFG_NF(GPP_R4, NONE, DEEP, NF2), /* I2S_SPKR_SCLK_R */ + PAD_CFG_NF(GPP_R5, NONE, DEEP, NF2), /* I2S_SPKR_SFRM_R */ + PAD_CFG_NF(GPP_R6, NONE, DEEP, NF2), /* I2S_PCH_TX_SPKR_RX_R */ + PAD_CFG_NF(GPP_R7, NONE, DEEP, NF2), /* I2S_PCH_RX_SPKR_TX */ +}; + +static const struct pad_config i2s0_disable_pads[] = { + PAD_NC(GPP_R0, NONE), + PAD_NC(GPP_R1, NONE), + PAD_NC(GPP_R2, NONE), + PAD_NC(GPP_R3, NONE), +}; + +static const struct pad_config i2s2_disable_pads[] = { + PAD_NC(GPP_R4, NONE), + PAD_NC(GPP_R5, NONE), + PAD_NC(GPP_R6, NONE), + PAD_NC(GPP_R7, NONE), +}; + +static const struct pad_config bt_i2s_enable_pads[] = { + PAD_CFG_NF(GPP_VGPIO_30, NONE, DEEP, NF3), /* BT_I2S_BCLK */ + PAD_CFG_NF(GPP_VGPIO_31, NONE, DEEP, NF3), /* BT_I2S_SYNC */ + PAD_CFG_NF(GPP_VGPIO_32, NONE, DEEP, NF3), /* BT_I2S_SDO */ + PAD_CFG_NF(GPP_VGPIO_33, NONE, DEEP, NF3), /* BT_I2S_SDI */ + PAD_CFG_NF(GPP_VGPIO_34, NONE, DEEP, NF1), /* SSP2_SCLK */ + PAD_CFG_NF(GPP_VGPIO_35, NONE, DEEP, NF1), /* SSP2_SFRM */ + PAD_CFG_NF(GPP_VGPIO_36, NONE, DEEP, NF1), /* SSP_TXD */ + PAD_CFG_NF(GPP_VGPIO_37, NONE, DEEP, NF1), /* SSP_RXD */ +}; + +static const struct pad_config bt_i2s_disable_pads[] = { + PAD_NC(GPP_VGPIO_30, NONE), + PAD_NC(GPP_VGPIO_31, NONE), + PAD_NC(GPP_VGPIO_32, NONE), + PAD_NC(GPP_VGPIO_33, NONE), + PAD_NC(GPP_VGPIO_34, NONE), + PAD_NC(GPP_VGPIO_35, NONE), + PAD_NC(GPP_VGPIO_36, NONE), + PAD_NC(GPP_VGPIO_37, NONE), +}; + +static void enable_i2s(void) +{ + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s0_enable_pads, ARRAY_SIZE(i2s0_enable_pads)); + gpio_configure_pads(i2s2_enable_pads, ARRAY_SIZE(i2s2_enable_pads)); + gpio_configure_pads(sndw_disable_pads, ARRAY_SIZE(sndw_disable_pads)); +} + +static void fw_config_handle(void *unused) +{ + if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) { + printk(BIOS_INFO, "Disable audio related GPIO pins.\n"); + gpio_configure_pads(i2s0_disable_pads, ARRAY_SIZE(i2s0_disable_pads)); + gpio_configure_pads(i2s2_disable_pads, ARRAY_SIZE(i2s2_disable_pads)); + gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads)); + gpio_configure_pads(sndw_disable_pads, ARRAY_SIZE(sndw_disable_pads)); + return; + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98373_ALC5682_SNDW))) { + printk(BIOS_INFO, "Configure audio over SoundWire with MAX98373 ALC5682.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(sndw_enable_pads, ARRAY_SIZE(sndw_enable_pads)); + printk(BIOS_INFO, "BT offload enabled\n"); + gpio_configure_pads(i2s0_enable_pads, ARRAY_SIZE(i2s0_enable_pads)); + gpio_configure_pads(i2s2_disable_pads, ARRAY_SIZE(i2s2_disable_pads)); + gpio_configure_pads(bt_i2s_enable_pads, ARRAY_SIZE(bt_i2s_enable_pads)); + } else { + printk(BIOS_INFO, "BT offload disabled\n"); + gpio_configure_pads(i2s0_disable_pads, ARRAY_SIZE(i2s0_disable_pads)); + gpio_configure_pads(i2s2_disable_pads, ARRAY_SIZE(i2s2_disable_pads)); + gpio_configure_pads(bt_i2s_disable_pads, ARRAY_SIZE(bt_i2s_disable_pads)); + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98357_ALC5682I_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98357 ALC5682I.\n"); + enable_i2s(); + } + + if (fw_config_probe(FW_CONFIG(AUDIO, ALC1019_NAU88L25B_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with ALC1019 NAU88L25B.\n"); + enable_i2s(); + } +} +BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL); diff --git a/src/mainboard/google/brya/variants/brya4es/gpio.c b/src/mainboard/google/brya/variants/brya4es/gpio.c new file mode 100644 index 0000000..c3cfc0c --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/gpio.c @@ -0,0 +1,153 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/variants.h> +#include <boardid.h> +#include <console/console.h> +#include <soc/gpio.h> +#include <string.h> + +static const struct pad_config board_id0_1_overrides[] = { + /* B2 : VRALERT# ==> NC */ + PAD_NC(GPP_B2, NONE), + /* B15 : TIME_SYNC0 ==> NC */ + PAD_NC(GPP_B15, NONE), + /* C3 : SML0CLK ==> NC */ + PAD_NC(GPP_C3, NONE), + /* C4 : SML0DATA ==> NC */ + PAD_NC(GPP_C4, NONE), + /* D13 : ISH_UART0_RXD ==> PCH_I2C_CAM_SDA */ + PAD_CFG_NF(GPP_D13, NONE, DEEP, NF3), + /* D14 : ISH_UART0_TXD ==> PCH_I2C_CAM_SCL */ + PAD_CFG_NF(GPP_D14, NONE, DEEP, NF3), + /* F19 : SRCCLKREQ6# ==> WWAN_SIM1_DET_OD */ + PAD_CFG_GPI(GPP_F19, UP_20K, DEEP), + /* F20 : EXT_PWR_GATE# ==> HPS_RST_R */ + PAD_CFG_GPO(GPP_F20, 0, DEEP), + /* F21 : EXT_PWR_GATE2# ==> WAKE_ON_WWAN_ODL */ + PAD_NC(GPP_F21, NONE), + /* H21 : IMGCLKOUT2 ==> WLAN_INT_L */ + PAD_CFG_GPI_APIC(GPP_H21, NONE, DEEP, EDGE_SINGLE, NONE), + /* GPD2: LAN_WAKE# ==> NC */ + PAD_NC(GPD2, NONE), +}; + +/* Early pad configuration in bootblock for board id < 2 */ +static const struct pad_config early_gpio_table[] = { + /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */ + PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT), + /* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */ + PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2), + /* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */ + PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2), + /* + * D1 : ISH_GP1 ==> FP_RST_ODL + * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down. + * To ensure proper power sequencing for the FPMCU device, reset signal is driven low + * early on in bootblock, followed by enabling of power. Reset signal is deasserted + * later on in ramstage. Since reset signal is asserted in bootblock, it results in + * FPMCU not working after a S3 resume. This is a known issue. + */ + PAD_CFG_GPO(GPP_D1, 0, DEEP), + /* D2 : ISH_GP2 ==> EN_FP_PWR */ + PAD_CFG_GPO(GPP_D2, 1, DEEP), + /* E0 : SATAXPCIE0 ==> WWAN_PERST_L (updated in ramstage) */ + PAD_CFG_GPO(GPP_E0, 0, DEEP), + /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */ + PAD_CFG_GPI(GPP_E13, NONE, DEEP), + /* E16 : RSVD_TP ==> WWAN_RST_L (updated in ramstage) */ + PAD_CFG_GPO(GPP_E16, 0, DEEP), + /* E15 : RSVD_TP ==> PCH_WP_OD */ + PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP), + /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */ + PAD_CFG_GPI(GPP_F18, NONE, DEEP), + /* F21 : EXT_PWR_GATE2# ==> NC */ + PAD_NC(GPP_F21, NONE), + /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */ + PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2), + /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */ + PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2), + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_NC(GPP_H13, UP_20K), +}; + +/* Early pad configuration in bootblock for board id 2 */ +static const struct pad_config early_gpio_table_id2[] = { + /* A12 : SATAXPCIE1 ==> EN_PP3300_WWAN */ + PAD_CFG_GPO(GPP_A12, 1, DEEP), + /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */ + PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT), + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 0, DEEP), + /* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */ + PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2), + /* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */ + PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2), + /* + * D1 : ISH_GP1 ==> FP_RST_ODL + * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down. + * To ensure proper power sequencing for the FPMCU device, reset signal is driven low + * early on in bootblock, followed by enabling of power. Reset signal is deasserted + * later on in ramstage. Since reset signal is asserted in bootblock, it results in + * FPMCU not working after a S3 resume. This is a known issue. + */ + PAD_CFG_GPO(GPP_D1, 0, DEEP), + /* D2 : ISH_GP2 ==> EN_FP_PWR */ + PAD_CFG_GPO(GPP_D2, 1, DEEP), + /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */ + PAD_CFG_GPO(GPP_D11, 1, DEEP), + /* E0 : SATAXPCIE0 ==> WWAN_PERST_L (updated in ramstage) */ + PAD_CFG_GPO(GPP_E0, 0, DEEP), + /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */ + PAD_CFG_GPI(GPP_E13, NONE, DEEP), + /* E16 : RSVD_TP ==> WWAN_RST_L (updated in ramstage) */ + PAD_CFG_GPO(GPP_E16, 0, DEEP), + /* E15 : RSVD_TP ==> PCH_WP_OD */ + PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP), + /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */ + PAD_CFG_GPI(GPP_F18, NONE, DEEP), + /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (updated in romstage) */ + PAD_CFG_GPO(GPP_F21, 0, DEEP), + /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */ + PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2), + /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */ + PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2), + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_NC(GPP_H13, UP_20K), +}; + +static const struct pad_config romstage_gpio_table[] = { + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 1, DEEP), + /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (set here for correct power sequencing) */ + PAD_CFG_GPO(GPP_F21, 1, DEEP), +}; + +const struct pad_config *variant_gpio_override_table(size_t *num) +{ + const uint32_t id = board_id(); + if (id == BOARD_ID_UNKNOWN || id < 2) { + *num = ARRAY_SIZE(board_id0_1_overrides); + return board_id0_1_overrides; + } + + *num = 0; + return NULL; +} + +const struct pad_config *variant_early_gpio_table(size_t *num) +{ + const uint32_t id = board_id(); + if (id == BOARD_ID_UNKNOWN || id < 2) { + *num = ARRAY_SIZE(early_gpio_table); + return early_gpio_table; + } + + *num = ARRAY_SIZE(early_gpio_table_id2); + return early_gpio_table_id2; +} + +const struct pad_config *variant_romstage_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(romstage_gpio_table); + return romstage_gpio_table; +} diff --git a/src/mainboard/google/brya/variants/brya4es/include/variant/ec.h b/src/mainboard/google/brya/variants/brya4es/include/variant/ec.h new file mode 100644 index 0000000..4fc0622 --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/include/variant/ec.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef MAINBOARD_EC_H +#define MAINBOARD_EC_H + +#include <baseboard/ec.h> + +#endif /* MAINBOARD_GPIO_H */ diff --git a/src/mainboard/google/brya/variants/brya4es/include/variant/gpio.h b/src/mainboard/google/brya/variants/brya4es/include/variant/gpio.h new file mode 100644 index 0000000..23338de --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/include/variant/gpio.h @@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __MAINBOARD_GPIO_H__ +#define __MAINBOARD_GPIO_H__ + +#include <baseboard/gpio.h> + +#define WWAN_FCPO GPP_F21 +#define WWAN_RST GPP_E16 +#define WWAN_PERST GPP_E0 +#define T1_OFF_MS 16 +#define T2_OFF_MS 2 + +#endif /* __MAINBOARD_GPIO_H__ */ diff --git a/src/mainboard/google/brya/variants/brya4es/memory/Makefile.inc b/src/mainboard/google/brya/variants/brya4es/memory/Makefile.inc new file mode 100644 index 0000000..70c8d17 --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/memory/Makefile.inc @@ -0,0 +1,10 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/brya0/memory src/mainboard/google/brya/variants/brya0/memory/mem_parts_used.txt + +SPD_SOURCES = +SPD_SOURCES += spd/lp4x/set-0/spd-1.hex # ID = 0(0b0000) Parts = MT53E512M32D2NP-046 WT:F, H9HCNNNBKMMLXR-NEE +SPD_SOURCES += spd/lp4x/set-0/spd-4.hex # ID = 1(0b0001) Parts = MT53E1G32D2NP-046 WT:A +SPD_SOURCES += spd/lp4x/set-0/spd-7.hex # ID = 2(0b0010) Parts = MT53E2G32D4NQ-046 WT:A +SPD_SOURCES += spd/lp4x/set-0/spd-3.hex # ID = 3(0b0011) Parts = H9HCNNNCPMMLXR-NEE, MT53E1G32D2NP-046 WT:B diff --git a/src/mainboard/google/brya/variants/brya4es/memory/dram_id.generated.txt b/src/mainboard/google/brya/variants/brya4es/memory/dram_id.generated.txt new file mode 100644 index 0000000..bfc1ead --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/memory/dram_id.generated.txt @@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/brya0/memory src/mainboard/google/brya/variants/brya0/memory/mem_parts_used.txt + +DRAM Part Name ID to assign +MT53E512M32D2NP-046 WT:F 0 (0000) +H9HCNNNBKMMLXR-NEE 0 (0000) +MT53E1G32D2NP-046 WT:A 1 (0001) +MT53E2G32D4NQ-046 WT:A 2 (0010) +H9HCNNNCPMMLXR-NEE 3 (0011) +MT53E1G32D2NP-046 WT:B 3 (0011) diff --git a/src/mainboard/google/brya/variants/brya4es/memory/mem_parts_used.txt b/src/mainboard/google/brya/variants/brya4es/memory/mem_parts_used.txt new file mode 100644 index 0000000..c8a24cc --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/memory/mem_parts_used.txt @@ -0,0 +1,6 @@ +MT53E512M32D2NP-046 WT:F +H9HCNNNBKMMLXR-NEE +MT53E1G32D2NP-046 WT:A +MT53E2G32D4NQ-046 WT:A +H9HCNNNCPMMLXR-NEE +MT53E1G32D2NP-046 WT:B diff --git a/src/mainboard/google/brya/variants/brya4es/overridetree.cb b/src/mainboard/google/brya/variants/brya4es/overridetree.cb new file mode 100644 index 0000000..6812f20 --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/overridetree.cb @@ -0,0 +1,742 @@ +fw_config + field DB_USB 0 3 + option USB_ABSENT 0 + option USB3_PS8815 1 + end + field DB_SD 4 5 + option SD_ABSENT 0 + option SD_GL9755S 1 + end + field KB_BL 7 7 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field AUDIO 8 10 + option AUDIO_UNKNOWN 0 + option MAX98357_ALC5682I_I2S 1 + option MAX98373_ALC5682_SNDW 2 + option MAX98373_NAU88L25B_I2S 3 + option ALC1019_NAU88L25B_I2S 4 + end + field DB_LTE 11 12 + option LTE_ABSENT 0 + option LTE_USB 1 + option LTE_PCIE 2 + end + field UFC 13 14 + option UFC_USB 0 + option UFC_MIPI_IMX208 1 + end + # Bits 15 and 16 were intended for WFC but never declared here + field HPS 17 17 + option HPS_ABSENT 0 + option HPS_PRESENT 1 + end +end + +chip soc/intel/alderlake + register "SaGv" = "SaGv_Enabled" + + register "PsysPmax" = "145" + + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MLB Port + + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port + + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + + # FIVR configurations for brya are disabled since the board doesn't have V1p05 and Vnn + # bypass rails implemented. + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 1, + }" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DRAM_SOC"" + register "options.tsr[1].desc" = ""Ambient"" + register "options.tsr[2].desc" = ""Charger"" + register "options.tsr[3].desc" = ""WWAN"" + + # TODO: below values are initial reference values only + ## Active Policy + register "policies.active" = "{ + [0] = { + .target = DPTF_CPU, + .thresholds = { + TEMP_PCT(85, 90), + TEMP_PCT(80, 80), + TEMP_PCT(75, 70), + TEMP_PCT(70, 50), + TEMP_PCT(65, 30), + } + }, + [1] = { + .target = DPTF_TEMP_SENSOR_1, + .thresholds = { + TEMP_PCT(50, 90), + TEMP_PCT(48, 70), + TEMP_PCT(46, 60), + TEMP_PCT(43, 40), + TEMP_PCT(40, 30), + } + } + }" + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 75, 5000), + [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 5000), + [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 3000, + .max_power = 15000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200, + }, + .pl2 = { + .min_power = 55000, + .max_power = 55000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + ## Fan Performance Control (Percent, Speed, Noise, Power) + register "controls.fan_perf" = "{ + [0] = { 90, 6700, 220, 2200, }, + [1] = { 80, 5800, 180, 1800, }, + [2] = { 70, 5000, 145, 1450, }, + [3] = { 60, 4900, 115, 1150, }, + [4] = { 50, 3838, 90, 900, }, + [5] = { 40, 2904, 55, 550, }, + [6] = { 30, 2337, 30, 300, }, + [7] = { 20, 1608, 15, 150, }, + [8] = { 10, 800, 10, 100, }, + [9] = { 0, 0, 0, 50, } + }" + + ## Fan options + register "options.fan.fine_grained_control" = "1" + register "options.fan.step_size" = "2" + + device generic 0 alias dptf_policy on end + end + end + device ref ipu on + chip drivers/intel/mipi_camera + register "acpi_uid" = "0x50000" + register "acpi_name" = ""IPU0"" + register "device_type" = "INTEL_ACPI_CAMERA_CIO2" + + register "cio2_num_ports" = "1" + register "cio2_lanes_used" = "{4}" # 4 CSI Camera lanes are used + register "cio2_lane_endpoint[0]" = ""^I2C0.CAM0"" + register "cio2_prt[0]" = "2" + device generic 0 on + # MIPI lanes are split between UFC and WFC depending on + # whether the UFC is USB or MIPI hence probing UFC_USB + probe UFC UFC_USB + end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "0x50000" + register "acpi_name" = ""IPU0"" + register "device_type" = "INTEL_ACPI_CAMERA_CIO2" + + register "cio2_num_ports" = "2" + register "cio2_lanes_used" = "{4,2}" # 4 and 2 CSI Camera lanes are used + register "cio2_lane_endpoint[0]" = ""^I2C0.CAM0"" + register "cio2_lane_endpoint[1]" = ""^I2C2.CAM1"" + register "cio2_prt[0]" = "2" + register "cio2_prt[1]" = "1" + device generic 1 on + probe UFC UFC_MIPI_IMX208 + end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end + device ref pcie_rp6 on + probe DB_LTE LTE_PCIE + end + device ref tcss_dma0 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port1 as dfp[0].typec_port + device generic 0 on end + end + end + device ref tcss_dma1 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port3 as dfp[0].typec_port + device generic 0 on end + end + end + device ref pcie_rp8 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" + register "srcclk_pin" = "3" + device generic 0 on end + end + end #PCIE8 SD card + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO MAX98357_ALC5682I_I2S + end + end + chip drivers/i2c/nau8825 + register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x0c" + register "sar_threshold[1]" = "0x1c" + register "sar_threshold[2]" = "0x38" + register "sar_threshold[3]" = "0x60" + register "sar_hysteresis" = "1" + register "sar_voltage" = "0" # VDDA + register "sar_compare_time" = "0" # 500ns + register "sar_sampling_time" = "0" # 2us + register "short_key_debounce" = "2" # 100ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "7" # 512ms + device i2c 1a on + probe AUDIO ALC1019_NAU88L25B_I2S + end + end + chip drivers/generic/alc1015 + register "hid" = ""RTL1019"" + register "sdb" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + device generic 1 on + probe AUDIO ALC1019_NAU88L25B_I2S + end + end + chip drivers/intel/mipi_camera + register "acpi_hid" = ""OVTI8856"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM0"" + register "chip_name" = ""Ov 8856 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + + register "ssdb.lanes_used" = "4" + register "ssdb.link_used" = "0" + register "ssdb.vcm_type" = "0x0C" + register "vcm_name" = ""VCM0"" + register "num_freq_entries" = "2" + register "link_freq[0]" = "360 * MHz" # 360 MHz + register "link_freq[1]" = "180 * MHz" # 180 MHz + register "remote_name" = ""IPU0"" + + register "has_power_resource" = "1" + #Controls + register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" + register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" + + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #power_enable_2p8 + register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" #power_enable_1p2 + register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" #reset + + #_ON + register "on_seq.ops_cnt" = "5" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" + register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" + + #_OFF + register "off_seq.ops_cnt" = "4" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 10 on end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "2" + register "acpi_name" = ""VCM0"" + register "chip_name" = ""DW9768 VCM"" + register "device_type" = "INTEL_ACPI_CAMERA_VCM" + + register "pr0" = ""\_SB.PCI0.I2C0.CAM0.PRIC"" + register "vcm_compat" = ""dongwoon,dw9768"" + + device i2c 0C on end + end + chip drivers/intel/mipi_camera + register "acpi_uid" = "1" + register "acpi_name" = ""NVM0"" + register "chip_name" = ""AT24 EEPROM"" + register "device_type" = "INTEL_ACPI_CAMERA_NVM" + + register "pr0" = ""\_SB.PCI0.I2C0.CAM0.PRIC"" + register "nvm_compat" = ""atmel,24c1024"" + + register "nvm_size" = "0x2800" + register "nvm_pagesize" = "0x01" + register "nvm_readonly" = "0x01" + register "nvm_width" = "0x10" + + device i2c 58 on end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9050"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "300" + register "generic.reset_off_delay_ms" = "1" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "6" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 0x10 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "120" + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "12" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 0x5d on end + end + chip drivers/i2c/hid + register "generic.hid" = ""SIS9815"" + register "generic.desc" = ""SIS Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_delay_ms" = "100" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "7" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x00" + device i2c 5c on end + end + end + device ref i2c2 on + chip drivers/i2c/sx9324 + register "desc" = ""SAR1 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "1" + register "reg_gnrl_ctrl0" = "0x16" + register "reg_gnrl_ctrl1" = "0x21" + register "reg_afe_ctrl0" = "0x00" + register "reg_afe_ctrl1" = "0x10" + register "reg_afe_ctrl2" = "0x00" + register "reg_afe_ctrl3" = "0x00" + register "reg_afe_ctrl4" = "0x07" + register "reg_afe_ctrl5" = "0x00" + register "reg_afe_ctrl6" = "0x00" + register "reg_afe_ctrl7" = "0x07" + register "reg_afe_ctrl8" = "0x12" + register "reg_afe_ctrl9" = "0x0f" + register "reg_prox_ctrl0" = "0x12" + register "reg_prox_ctrl1" = "0x12" + register "reg_prox_ctrl2" = "0x90" + register "reg_prox_ctrl3" = "0x60" + register "reg_prox_ctrl4" = "0x0c" + register "reg_prox_ctrl5" = "0x12" + register "reg_prox_ctrl6" = "0x3c" + register "reg_prox_ctrl7" = "0x58" + register "reg_adv_ctrl0" = "0x00" + register "reg_adv_ctrl1" = "0x00" + register "reg_adv_ctrl2" = "0x00" + register "reg_adv_ctrl3" = "0x00" + register "reg_adv_ctrl4" = "0x00" + register "reg_adv_ctrl5" = "0x05" + register "reg_adv_ctrl6" = "0x00" + register "reg_adv_ctrl7" = "0x00" + register "reg_adv_ctrl8" = "0x00" + register "reg_adv_ctrl9" = "0x00" + register "reg_adv_ctrl10" = "0x5c" + register "reg_adv_ctrl11" = "0x52" + register "reg_adv_ctrl12" = "0xb5" + register "reg_adv_ctrl13" = "0x00" + register "reg_adv_ctrl14" = "0x80" + register "reg_adv_ctrl15" = "0x0c" + register "reg_adv_ctrl16" = "0x38" + register "reg_adv_ctrl17" = "0x56" + register "reg_adv_ctrl18" = "0x33" + register "reg_adv_ctrl19" = "0xf0" + register "reg_adv_ctrl20" = "0xf0" + device i2c 28 on end + end + chip drivers/i2c/sx9324 + register "desc" = ""SAR2 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "2" + register "reg_gnrl_ctrl0" = "0x16" + register "reg_gnrl_ctrl1" = "0x21" + register "reg_afe_ctrl0" = "0x00" + register "reg_afe_ctrl1" = "0x10" + register "reg_afe_ctrl2" = "0x00" + register "reg_afe_ctrl3" = "0x00" + register "reg_afe_ctrl4" = "0x07" + register "reg_afe_ctrl5" = "0x00" + register "reg_afe_ctrl6" = "0x00" + register "reg_afe_ctrl7" = "0x07" + register "reg_afe_ctrl8" = "0x12" + register "reg_afe_ctrl9" = "0x0f" + register "reg_prox_ctrl0" = "0x12" + register "reg_prox_ctrl1" = "0x12" + register "reg_prox_ctrl2" = "0x90" + register "reg_prox_ctrl3" = "0x60" + register "reg_prox_ctrl4" = "0x0c" + register "reg_prox_ctrl5" = "0x12" + register "reg_prox_ctrl6" = "0x3c" + register "reg_prox_ctrl7" = "0x58" + register "reg_adv_ctrl0" = "0x00" + register "reg_adv_ctrl1" = "0x00" + register "reg_adv_ctrl2" = "0x00" + register "reg_adv_ctrl3" = "0x00" + register "reg_adv_ctrl4" = "0x00" + register "reg_adv_ctrl5" = "0x05" + register "reg_adv_ctrl6" = "0x00" + register "reg_adv_ctrl7" = "0x00" + register "reg_adv_ctrl8" = "0x00" + register "reg_adv_ctrl9" = "0x00" + register "reg_adv_ctrl10" = "0x5c" + register "reg_adv_ctrl11" = "0x52" + register "reg_adv_ctrl12" = "0xb5" + register "reg_adv_ctrl13" = "0x00" + register "reg_adv_ctrl14" = "0x80" + register "reg_adv_ctrl15" = "0x0c" + register "reg_adv_ctrl16" = "0x38" + register "reg_adv_ctrl17" = "0x56" + register "reg_adv_ctrl18" = "0x33" + register "reg_adv_ctrl19" = "0xf0" + register "reg_adv_ctrl20" = "0xf0" + device i2c 2C on end + end + chip drivers/intel/mipi_camera + register "acpi_hid" = ""INT3478"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM1"" + register "chip_name" = ""imx 208 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + + register "ssdb.lanes_used" = "2" + register "ssdb.link_used" = "1" + register "num_freq_entries" = "2" + register "link_freq[0]" = "384 * MHz" # 384 MHz + register "link_freq[1]" = "96 * MHz" # 96 MHz + register "remote_name" = ""IPU0"" + + register "has_power_resource" = "1" + #Controls + register "gpio_panel.gpio[0].gpio_num" = "GPP_C3" #PP3300_FCAM_X + register "gpio_panel.gpio[1].gpio_num" = "GPP_A17" #EN_UCAM_PWR + register "gpio_panel.gpio[2].gpio_num" = "GPP_F20" #reset + register "gpio_panel.gpio[3].gpio_num" = "GPP_H21" #CLK_EN + + #_ON + register "on_seq.ops_cnt" = "5" + register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(3, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" + register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" + + #_OFF + register "off_seq.ops_cnt" = "4" + register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(3, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + device i2c 10 on + probe UFC UFC_MIPI_IMX208 + end + end + chip drivers/intel/mipi_camera + register "acpi_hid" = ""INT3499"" + register "acpi_uid" = "1" + register "acpi_name" = ""NVM1"" + register "chip_name" = ""GT24C16S"" + register "device_type" = "INTEL_ACPI_CAMERA_NVM" + + register "pr0" = ""\_SB.PCI0.I2C2.CAM1.PRIC"" + + register "nvm_size" = "0x2800" + register "nvm_pagesize" = "0x01" + register "nvm_readonly" = "0x01" + register "nvm_width" = "0x0E" + + device i2c 50 on + probe UFC UFC_MIPI_IMX208 + end + end + chip drivers/i2c/generic + register "hid" = ""GOOG0020"" + register "desc" = ""Chrome OS HPS"" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E7)" # EN_HPS_PWR + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E3_IRQ)" # HPS_INT_ODL + # HPS uses I2C addresses 0x30 and 0x51. + # The address we provide here is not significant because + # neither coreboot nor Linux have a driver for HPS, + # it's only used from userspace. + device i2c 30 on + probe HPS HPS_PRESENT + end + end + end + device ref i2c3 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on end + end + end + device ref hda on + chip drivers/generic/max98357a + register "hid" = ""MX98357A"" + register "sdmode_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + register "sdmode_delay" = "5" + device generic 0 on + probe AUDIO MAX98357_ALC5682I_I2S + end + end + + chip drivers/intel/soundwire + device generic 0 on + probe AUDIO MAX98373_ALC5682_SNDW + chip drivers/soundwire/alc5682 + # SoundWire Link 0 ID 1 + register "desc" = ""Headset Codec"" + device generic 0.1 on end + end + chip drivers/soundwire/max98373 + # SoundWire Link 2 ID 3 + register "desc" = ""Left Speaker Amp"" + device generic 2.3 on end + end + chip drivers/soundwire/max98373 + # SoundWire Link 2 ID 7 + register "desc" = ""Right Speaker Amp"" + device generic 2.7 on end + end + end + end + end + device ref gspi1 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" + register "wake" = "GPE0_DW2_15" + device spi 0 on end + end # FPMCU + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + use conn2 as mux_conn[2] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "1" + register "usb3_port_number" = "1" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "2" + register "usb3_port_number" = "2" + device generic 1 alias conn1 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "3" + register "usb3_port_number" = "3" + device generic 2 alias conn2 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device ref tcss_usb3_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C2 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C2 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on + probe UFC UFC_USB + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (DB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb2_port9 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb3_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port4 on end + end + end + end + end + end +end diff --git a/src/mainboard/google/brya/variants/brya4es/ramstage.c b/src/mainboard/google/brya/variants/brya4es/ramstage.c new file mode 100644 index 0000000..06040e4 --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/ramstage.c @@ -0,0 +1,20 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/variants.h> +#include <device/pci_ids.h> + +const struct cpu_power_limits limits[] = { + /* SKU_ID, TDP (Watts), pl1_min, pl1_max, pl2_min, pl2_max, pl4 */ + /* All values are for baseline config as per bug:191906315 comment #10 */ + { PCI_DEVICE_ID_INTEL_ADL_P_ID_7, 15, 3000, 15000, 39000, 39000, 100000 }, + { PCI_DEVICE_ID_INTEL_ADL_P_ID_6, 15, 3000, 15000, 39000, 39000, 100000 }, + { PCI_DEVICE_ID_INTEL_ADL_P_ID_5, 28, 4000, 28000, 43000, 43000, 105000 }, + { PCI_DEVICE_ID_INTEL_ADL_P_ID_3, 28, 4000, 28000, 43000, 43000, 105000 }, + { PCI_DEVICE_ID_INTEL_ADL_P_ID_3, 45, 5000, 45000, 80000, 80000, 159000 }, +}; + +void variant_devtree_update(void) +{ + size_t total_entries = ARRAY_SIZE(limits); + variant_update_power_limits(limits, total_entries); +} diff --git a/src/mainboard/google/brya/variants/brya4es/variant.c b/src/mainboard/google/brya/variants/brya4es/variant.c new file mode 100644 index 0000000..8d4471b --- /dev/null +++ b/src/mainboard/google/brya/variants/brya4es/variant.c @@ -0,0 +1,10 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <chip.h> +#include <fw_config.h> +#include <baseboard/variants.h> + +void variant_update_soc_chip_config(struct soc_intel_alderlake_config *config) +{ + config->CnviBtAudioOffload = fw_config_probe(FW_CONFIG(AUDIO, MAX98373_ALC5682_SNDW)); +} diff --git a/src/mainboard/google/brya/variants/gimble4es/Makefile.inc b/src/mainboard/google/brya/variants/gimble4es/Makefile.inc new file mode 100644 index 0000000..446d113 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/Makefile.inc @@ -0,0 +1,10 @@ +# SPDX-License-Identifier: GPL-2.0-only +bootblock-y += gpio.c + +romstage-y += gpio.c + +ramstage-y += gpio.c + +ramstage-$(CONFIG_FW_CONFIG) += fw_config.c + +ramstage-y += variant.c diff --git a/src/mainboard/google/brya/variants/gimble4es/fw_config.c b/src/mainboard/google/brya/variants/gimble4es/fw_config.c new file mode 100644 index 0000000..e9d87b3 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/fw_config.c @@ -0,0 +1,89 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <fw_config.h> +#include <gpio.h> + +static const struct pad_config dmic_enable_pads[] = { + PAD_CFG_NF(GPP_R4, NONE, DEEP, NF3), /* DMIC_CLK0_R */ + PAD_CFG_NF(GPP_R5, NONE, DEEP, NF3), /* DMIC_DATA0_R */ + PAD_CFG_NF(GPP_R6, NONE, DEEP, NF3), /* DMIC_CLK1_R */ + PAD_CFG_NF(GPP_R7, NONE, DEEP, NF3), /* DMIC_DATA1_R */ +}; + +static const struct pad_config dmic_disable_pads[] = { + PAD_NC(GPP_R4, NONE), + PAD_NC(GPP_R5, NONE), + PAD_NC(GPP_R6, NONE), + PAD_NC(GPP_R7, NONE), +}; + +static const struct pad_config i2s_enable_pads[] = { + PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK_R */ + PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM_R */ + PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */ + PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */ + PAD_CFG_NF(GPP_S0, NONE, DEEP, NF4), /* I2S_SPKR_SCLK_R */ + PAD_CFG_NF(GPP_S1, NONE, DEEP, NF4), /* I2S_SPKR_SFRM_R */ + PAD_CFG_NF(GPP_S2, NONE, DEEP, NF4), /* I2S_PCH_TX_SPKR_RX_R */ + PAD_CFG_NF(GPP_S3, NONE, DEEP, NF4), /* I2S_PCH_RX_SPKR_TX */ +}; + +static const struct pad_config i2s_disable_pads[] = { + PAD_NC(GPP_R0, NONE), + PAD_NC(GPP_R1, NONE), + PAD_NC(GPP_R2, NONE), + PAD_NC(GPP_R3, NONE), + PAD_NC(GPP_S0, NONE), + PAD_NC(GPP_S1, NONE), + PAD_NC(GPP_S2, NONE), + PAD_NC(GPP_S3, NONE), +}; + +static const struct pad_config bt_i2s_enable_pads[] = { + PAD_CFG_NF(GPP_VGPIO_30, NONE, DEEP, NF3), /* BT_I2S_BCLK */ + PAD_CFG_NF(GPP_VGPIO_31, NONE, DEEP, NF3), /* BT_I2S_SYNC */ + PAD_CFG_NF(GPP_VGPIO_32, NONE, DEEP, NF3), /* BT_I2S_SDO */ + PAD_CFG_NF(GPP_VGPIO_33, NONE, DEEP, NF3), /* BT_I2S_SDI */ + PAD_CFG_NF(GPP_VGPIO_34, NONE, DEEP, NF1), /* SSP2_SCLK */ + PAD_CFG_NF(GPP_VGPIO_35, NONE, DEEP, NF1), /* SSP2_SFRM */ + PAD_CFG_NF(GPP_VGPIO_36, NONE, DEEP, NF1), /* SSP_TXD */ + PAD_CFG_NF(GPP_VGPIO_37, NONE, DEEP, NF1), /* SSP_RXD */ +}; + +static const struct pad_config bt_i2s_disable_pads[] = { + PAD_NC(GPP_VGPIO_30, NONE), + PAD_NC(GPP_VGPIO_31, NONE), + PAD_NC(GPP_VGPIO_32, NONE), + PAD_NC(GPP_VGPIO_33, NONE), + PAD_NC(GPP_VGPIO_34, NONE), + PAD_NC(GPP_VGPIO_35, NONE), + PAD_NC(GPP_VGPIO_36, NONE), + PAD_NC(GPP_VGPIO_37, NONE), +}; + +static void fw_config_handle(void *unused) +{ + if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) { + printk(BIOS_INFO, "Disable audio related GPIO pins.\n"); + gpio_configure_pads(i2s_disable_pads, ARRAY_SIZE(i2s_disable_pads)); + gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads)); + gpio_configure_pads(bt_i2s_disable_pads, ARRAY_SIZE(bt_i2s_disable_pads)); + return; + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98390_ALC5682I_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98390 ALC5682I.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98390_ALC5682I_I2S_SSP1))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98390 ALC5682I.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + gpio_configure_pads(bt_i2s_enable_pads, ARRAY_SIZE(bt_i2s_enable_pads)); + } +} +BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL); diff --git a/src/mainboard/google/brya/variants/gimble4es/gpio.c b/src/mainboard/google/brya/variants/gimble4es/gpio.c new file mode 100644 index 0000000..2ea9f90 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/gpio.c @@ -0,0 +1,176 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/gpio.h> +#include <baseboard/variants.h> +#include <commonlib/helpers.h> +#include <soc/gpio.h> + +/* Pad configuration in ramstage */ +static const struct pad_config override_gpio_table[] = { + /* A6 : ESPI_ALERT1# ==> NC */ + PAD_NC(GPP_A6, NONE), + /* A7 : SRCCLK_OE7# ==> NC */ + PAD_NC(GPP_A7, NONE), + /* A8 : SRCCLKREQ7# ==> NC */ + PAD_NC(GPP_A8, NONE), + /* A12 : SATAXPCIE1 ==> NC */ + PAD_NC(GPP_A12, NONE), + /* A14 : USB_OC1# ==> NC */ + PAD_NC(GPP_A14, NONE), + /* A15 : USB_OC2# ==> NC */ + PAD_NC(GPP_A15, NONE), + /* A18 : DDSP_HPDB ==> NC */ + PAD_NC(GPP_A18, NONE), + /* A21 : DDPC_CTRCLK ==> NC */ + PAD_NC(GPP_A21, NONE), + /* A22 : DDPC_CTRLDATA ==> NC */ + PAD_NC(GPP_A22, NONE), + + /* B3 : PROC_GP2 ==> NC */ + PAD_NC(GPP_B3, NONE), + /* B5 : ISH_I2C0_SDA ==> NC */ + PAD_NC(GPP_B5, NONE), + /* B6 : ISH_I2C0_SCL ==> NC */ + PAD_NC(GPP_B6, NONE), + + /* C3 : SML0CLK ==> NC */ + PAD_NC(GPP_C3, NONE), + /* C4 : SML0DATA ==> NC */ + PAD_NC(GPP_C4, NONE), + + /* D3 : ISH_GP3 ==> NC */ + PAD_NC(GPP_D3, NONE), + /* D5 : SRCCLKREQ0# ==> NC */ + PAD_NC(GPP_D5, NONE), + /* D9 : ISH_SPI_CS# ==> NC */ + PAD_NC(GPP_D9, NONE), + /* D15 : ISH_UART0_RTS# ==> NC */ + PAD_NC(GPP_D15, NONE), + /* D16 : ISH_UART0_CTS# ==> EN_WCAM_PWR */ + PAD_CFG_GPO(GPP_D16, 1, DEEP), + /* D17 : UART1_RXD ==> NC */ + PAD_NC(GPP_D17, NONE), + + /* E0 : SATAXPCIE0 ==> NC */ + PAD_NC(GPP_E0, NONE), + /* E3 : PROC_GP0 ==> NC */ + PAD_NC(GPP_E3, NONE), + /* E4 : SATA_DEVSLP0 ==> NC */ + PAD_NC(GPP_E4, NONE), + /* E7 : PROC_GP1 ==> NC */ + PAD_NC(GPP_E7, NONE), + /* E10 : THC0_SPI1_CS# ==> NC */ + PAD_NC(GPP_E10, NONE), + /* E16 : RSVD_TP ==> NC */ + PAD_NC(GPP_E16, NONE), + /* E17 : THC0_SPI1_INT# ==> NC */ + PAD_NC(GPP_E17, NONE), + /* E18 : DDP1_CTRLCLK ==> NC */ + PAD_NC(GPP_E18, NONE), + /* E20 : DDP2_CTRLCLK ==> NC */ + PAD_NC(GPP_E20, NONE), + + /* F6 : CNV_PA_BLANKING ==> NC */ + PAD_NC(GPP_F6, NONE), + /* F19 : SRCCLKREQ6# ==> NC */ + PAD_NC(GPP_F19, NONE), + /* F20 : EXT_PWR_GATE# ==> NC */ + PAD_NC(GPP_F20, NONE), + /* F21 : EXT_PWR_GATE2# ==> NC */ + PAD_NC(GPP_F21, NONE), + + /* H8 : I2C4_SDA ==> NC */ + PAD_NC(GPP_H8, NONE), + /* H9 : I2C4_SCL ==> NC */ + PAD_NC(GPP_H9, NONE), + /* H15 : DDPB_CTRLCLK ==> NC */ + PAD_NC(GPP_H15, NONE), + /* H17 : DDPB_CTRLDATA ==> NC*/ + PAD_NC(GPP_H17, NONE), + /* H19 : SRCCLKREQ4# ==> NC */ + PAD_NC(GPP_H19, NONE), + /* H21 : IMGCLKOUT2 ==> NC */ + PAD_NC(GPP_H21, NONE), + /* H22 : IMGCLKOUT3 ==> NC */ + PAD_NC(GPP_H22, NONE), + /* H23 : SRCCLKREQ5# ==> NC */ + PAD_NC(GPP_H23, NONE), + + /* S4 : SNDW2_CLK ==> NC */ + PAD_NC(GPP_S4, NONE), + /* S5 : SNDW2_DATA ==> NC */ + PAD_NC(GPP_S5, NONE), + /* S6 : SNDW3_CLK ==> NC */ + PAD_NC(GPP_S6, NONE), + /* S7 : SNDW3_DATA ==> NC */ + PAD_NC(GPP_S7, NONE), + + /* GPD11: LANPHYC ==> NC */ + PAD_NC(GPD11, NONE), +}; + +/* Early pad configuration in bootblock */ +static const struct pad_config early_gpio_table[] = { + /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */ + PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT), + + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 0, DEEP), + /* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */ + PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2), + /* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */ + PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2), + /* + * D1 : ISH_GP1 ==> FP_RST_ODL + * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down. + * To ensure proper power sequencing for the FPMCU device, reset signal is driven low + * early on in bootblock, followed by enabling of power. Reset signal is deasserted + * later on in ramstage. Since reset signal is asserted in bootblock, it results in + * FPMCU not working after a S3 resume. This is a known issue. + */ + PAD_CFG_GPO(GPP_D1, 0, DEEP), + /* D2 : ISH_GP2 ==> EN_FP_PWR */ + PAD_CFG_GPO(GPP_D2, 1, DEEP), + /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */ + PAD_CFG_GPO(GPP_D11, 1, DEEP), + + /* E0 : SATAXPCIE0 ==> NC */ + PAD_NC(GPP_E0, NONE), + /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */ + PAD_CFG_GPI(GPP_E13, NONE, DEEP), + /* E15 : RSVD_TP ==> PCH_WP_OD */ + PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP), + /* E16 : RSVD_TP ==> NC */ + PAD_NC(GPP_E16, NONE), + /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */ + PAD_CFG_GPI(GPP_F18, NONE, DEEP), + /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */ + PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2), + /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */ + PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2), + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_NC(GPP_H13, UP_20K), +}; + +static const struct pad_config romstage_gpio_table[] = { + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 1, DEEP), +}; + +const struct pad_config *variant_gpio_override_table(size_t *num) +{ + *num = ARRAY_SIZE(override_gpio_table); + return override_gpio_table; +} + +const struct pad_config *variant_early_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(early_gpio_table); + return early_gpio_table; +} + +const struct pad_config *variant_romstage_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(romstage_gpio_table); + return romstage_gpio_table; +} diff --git a/src/mainboard/google/brya/variants/gimble4es/include/variant/ec.h b/src/mainboard/google/brya/variants/gimble4es/include/variant/ec.h new file mode 100644 index 0000000..7a2a6ff --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/include/variant/ec.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __VARIANT_EC_H__ +#define __VARIANT_EC_H__ + +#include <baseboard/ec.h> + +#endif diff --git a/src/mainboard/google/brya/variants/gimble4es/include/variant/gpio.h b/src/mainboard/google/brya/variants/gimble4es/include/variant/gpio.h new file mode 100644 index 0000000..c4fe342 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/include/variant/gpio.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef VARIANT_GPIO_H +#define VARIANT_GPIO_H + +#include <baseboard/gpio.h> + +#endif diff --git a/src/mainboard/google/brya/variants/gimble4es/memory/Makefile.inc b/src/mainboard/google/brya/variants/gimble4es/memory/Makefile.inc new file mode 100644 index 0000000..9db9484 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/memory/Makefile.inc @@ -0,0 +1,9 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/gimble/memory src/mainboard/google/brya/variants/gimble/memory/mem_parts_used.txt + +SPD_SOURCES = +SPD_SOURCES += spd/lp4x/set-0/spd-1.hex # ID = 0(0b0000) Parts = MT53E512M32D2NP-046 WT:E, H9HCNNNBKMMLXR-NEE, K4U6E3S4AA-MGCR, MT53E512M32D1NP-046 WT:B +SPD_SOURCES += spd/lp4x/set-0/spd-3.hex # ID = 1(0b0001) Parts = H9HCNNNCPMMLXR-NEE, K4UBE3D4AA-MGCR, MT53E1G32D2NP-046 WT:B +SPD_SOURCES += spd/lp4x/set-0/spd-4.hex # ID = 2(0b0010) Parts = MT53E1G32D2NP-046 WT:A diff --git a/src/mainboard/google/brya/variants/gimble4es/memory/dram_id.generated.txt b/src/mainboard/google/brya/variants/gimble4es/memory/dram_id.generated.txt new file mode 100644 index 0000000..c3a1347 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/memory/dram_id.generated.txt @@ -0,0 +1,14 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/gimble/memory src/mainboard/google/brya/variants/gimble/memory/mem_parts_used.txt + +DRAM Part Name ID to assign +MT53E512M32D2NP-046 WT:E 0 (0000) +H9HCNNNCPMMLXR-NEE 1 (0001) +H9HCNNNBKMMLXR-NEE 0 (0000) +MT53E1G32D2NP-046 WT:A 2 (0010) +K4U6E3S4AA-MGCR 0 (0000) +K4UBE3D4AA-MGCR 1 (0001) +MT53E512M32D1NP-046 WT:B 0 (0000) +MT53E1G32D2NP-046 WT:B 1 (0001) diff --git a/src/mainboard/google/brya/variants/gimble4es/memory/mem_parts_used.txt b/src/mainboard/google/brya/variants/gimble4es/memory/mem_parts_used.txt new file mode 100644 index 0000000..568e724 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/memory/mem_parts_used.txt @@ -0,0 +1,8 @@ +MT53E512M32D2NP-046 WT:E +H9HCNNNCPMMLXR-NEE +H9HCNNNBKMMLXR-NEE +MT53E1G32D2NP-046 WT:A +K4U6E3S4AA-MGCR +K4UBE3D4AA-MGCR +MT53E512M32D1NP-046 WT:B +MT53E1G32D2NP-046 WT:B diff --git a/src/mainboard/google/brya/variants/gimble4es/overridetree.cb b/src/mainboard/google/brya/variants/gimble4es/overridetree.cb new file mode 100644 index 0000000..8b6daf2 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/overridetree.cb @@ -0,0 +1,292 @@ +fw_config + field DB_USB 0 3 + option USB_ABSENT 0 + option USB3_PS8815 1 + end + field DB_SD 4 5 + option SD_ABSENT 0 + option SD_GL9750H 1 + end + field KB_BL 7 7 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field AUDIO 8 10 + option AUDIO_UNKNOWN 0 + option MAX98390_ALC5682I_I2S 1 + option MAX98390_ALC5682I_I2S_SSP1 2 + end + field DB_LTE 11 12 + option LTE_ABSENT 0 + end +end +chip soc/intel/alderlake + # This disabled autonomous GPIO power management, otherwise + # old cr50 FW only supports short pulses; need to clarify + # the minimum PCH IRQ pulse width with Intel, b/180111628 + register "gpio_override_pm" = "1" + register "gpio_pm[COMM_0]" = "0" + register "gpio_pm[COMM_1]" = "0" + register "gpio_pm[COMM_2]" = "0" + register "gpio_pm[COMM_3]" = "0" + register "gpio_pm[COMM_4]" = "0" + register "gpio_pm[COMM_5]" = "0" + register "SaGv" = "SaGv_Enabled" + register "TcssAuxOri" = "1" + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + register "usb2_ports[1]" = "USB2_PORT_MAX(OC1)" # set MAX to USB2_C1 for eye diagram + register "usb2_ports[2]" = "USB2_PORT_EMPTY" # Disable USB2_C2 + register "usb2_ports[3]" = "USB2_PORT_EMPTY" # M.2 WWAN + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MLB Port + register "usb2_ports[8]" = "USB2_PORT_EMPTY" # Type-A DB Port + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DRAM"" + register "options.tsr[1].desc" = ""Fan"" + register "options.tsr[2].desc" = ""Charger"" + # TODO: below values are initial reference values only + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 75, 5000), + }" + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + }" + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 12000, + .max_power = 15000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200, + }, + .pl2 = { + .min_power = 55000, + .max_power = 55000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + device generic 0 alias dptf_policy on end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end + device ref pcie_rp8 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" + register "srcclk_pin" = "3" + device generic 0 on end + end + end #PCIE8 SD card + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO MAX98390_ALC5682I_I2S + end + end + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO MAX98390_ALC5682I_I2S_SSP1 + end + end + chip drivers/i2c/max98390 + register "desc" = ""MAX98390 Speaker Amp 0"" + register "uid" = "0" + register "name" = ""MXW0"" + register "r0_calib_key" = ""dsm_calib_r0_0"" + register "temperature_calib_key" = ""dsm_calib_temp_0"" + register "dsm_param_file_name" = ""dsm_param_R"" + register "vmon_slot_no" = "0" + register "imon_slot_no" = "1" + device i2c 0x38 on + end + end + chip drivers/i2c/max98390 + register "desc" = ""MAX98390 Speaker Amp 1"" + register "uid" = "1" + register "name" = ""MXW1"" + register "r0_calib_key" = ""dsm_calib_r0_1"" + register "temperature_calib_key" = ""dsm_calib_temp_1"" + register "dsm_param_file_name" = ""dsm_param_L"" + register "vmon_slot_no" = "1" + register "imon_slot_no" = "0" + device i2c 0x3c on + end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9050"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "300" + register "generic.reset_off_delay_ms" = "1" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "6" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 0x15 on end + end + end + device ref i2c3 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 0x15 on end + end + end + device ref gspi1 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" + register "wake" = "GPE0_DW2_15" + device spi 0 on end + end # FPMCU + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "1" + register "usb3_port_number" = "1" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "2" + register "usb3_port_number" = "3" + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(2, 1)" + device ref usb2_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + register "privacy_gpio" = "ACPI_GPIO_INPUT_ACTIVE_LOW(GPP_D13)" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb3_port2 on end + end + end + end + end + end +end diff --git a/src/mainboard/google/brya/variants/gimble4es/variant.c b/src/mainboard/google/brya/variants/gimble4es/variant.c new file mode 100644 index 0000000..96ccf88 --- /dev/null +++ b/src/mainboard/google/brya/variants/gimble4es/variant.c @@ -0,0 +1,17 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <sar.h> +#include <chip.h> +#include <fw_config.h> +#include <baseboard/variants.h> + +const char *get_wifi_sar_cbfs_filename(void) +{ + return "wifi_sar_0.hex"; +} + +void variant_update_soc_chip_config(struct soc_intel_alderlake_config *config) +{ + config->CnviBtAudioOffload = fw_config_probe(FW_CONFIG(AUDIO, + MAX98390_ALC5682I_I2S_SSP1)); +} diff --git a/src/mainboard/google/brya/variants/primus4es/Makefile.inc b/src/mainboard/google/brya/variants/primus4es/Makefile.inc new file mode 100644 index 0000000..725b883 --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/Makefile.inc @@ -0,0 +1,6 @@ +# SPDX-License-Identifier: GPL-2.0-only +bootblock-y += gpio.c +romstage-y += gpio.c +ramstage-y += gpio.c +ramstage-$(CONFIG_FW_CONFIG) += fw_config.c +ramstage-y += variant.c diff --git a/src/mainboard/google/brya/variants/primus4es/fw_config.c b/src/mainboard/google/brya/variants/primus4es/fw_config.c new file mode 100644 index 0000000..c9b4a38 --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/fw_config.c @@ -0,0 +1,91 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <fw_config.h> +#include <gpio.h> + +static const struct pad_config dmic_enable_pads[] = { + PAD_CFG_NF(GPP_R4, NONE, DEEP, NF3), /* DMIC_CLK0_R */ + PAD_CFG_NF(GPP_R5, NONE, DEEP, NF3), /* DMIC_DATA0_R */ + PAD_CFG_NF(GPP_R6, NONE, DEEP, NF3), /* DMIC_CLK1_R */ + PAD_CFG_NF(GPP_R7, NONE, DEEP, NF3), /* DMIC_DATA1_R */ +}; + +static const struct pad_config dmic_disable_pads[] = { + PAD_NC(GPP_R4, NONE), + PAD_NC(GPP_R5, NONE), + PAD_NC(GPP_R6, NONE), + PAD_NC(GPP_R7, NONE), +}; + +static const struct pad_config i2s_enable_pads[] = { + PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK_R */ + PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM_R */ + PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */ + PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */ + PAD_CFG_NF(GPP_S0, NONE, DEEP, NF4), /* I2S_SPKR_SCLK_R */ + PAD_CFG_NF(GPP_S1, NONE, DEEP, NF4), /* I2S_SPKR_SFRM_R */ + PAD_CFG_NF(GPP_S2, NONE, DEEP, NF4), /* I2S_PCH_TX_SPKR_RX_R */ + PAD_CFG_NF(GPP_S3, NONE, DEEP, NF4), /* I2S_PCH_RX_SPKR_TX */ +}; + +static const struct pad_config i2s_disable_pads[] = { + PAD_NC(GPP_R0, NONE), + PAD_NC(GPP_R1, NONE), + PAD_NC(GPP_R2, NONE), + PAD_NC(GPP_R3, NONE), + PAD_NC(GPP_S0, NONE), + PAD_NC(GPP_S1, NONE), + PAD_NC(GPP_S2, NONE), + PAD_NC(GPP_S3, NONE), +}; + +static const struct pad_config bt_i2s_enable_pads[] = { + PAD_CFG_NF(GPP_VGPIO_30, NONE, DEEP, NF3), /* BT_I2S_BCLK */ + PAD_CFG_NF(GPP_VGPIO_31, NONE, DEEP, NF3), /* BT_I2S_SYNC */ + PAD_CFG_NF(GPP_VGPIO_32, NONE, DEEP, NF3), /* BT_I2S_SDO */ + PAD_CFG_NF(GPP_VGPIO_33, NONE, DEEP, NF3), /* BT_I2S_SDI */ + PAD_CFG_NF(GPP_VGPIO_34, NONE, DEEP, NF1), /* SSP2_SCLK */ + PAD_CFG_NF(GPP_VGPIO_35, NONE, DEEP, NF1), /* SSP2_SFRM */ + PAD_CFG_NF(GPP_VGPIO_36, NONE, DEEP, NF1), /* SSP_TXD */ + PAD_CFG_NF(GPP_VGPIO_37, NONE, DEEP, NF1), /* SSP_RXD */ +}; + +static const struct pad_config bt_i2s_disable_pads[] = { + PAD_NC(GPP_VGPIO_30, NONE), + PAD_NC(GPP_VGPIO_31, NONE), + PAD_NC(GPP_VGPIO_32, NONE), + PAD_NC(GPP_VGPIO_33, NONE), + PAD_NC(GPP_VGPIO_34, NONE), + PAD_NC(GPP_VGPIO_35, NONE), + PAD_NC(GPP_VGPIO_36, NONE), + PAD_NC(GPP_VGPIO_37, NONE), +}; + + +static void fw_config_handle(void *unused) +{ + if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) { + printk(BIOS_INFO, "Disable audio related GPIO pins.\n"); + gpio_configure_pads(i2s_disable_pads, ARRAY_SIZE(i2s_disable_pads)); + gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads)); + gpio_configure_pads(bt_i2s_disable_pads, ARRAY_SIZE(bt_i2s_disable_pads)); + return; + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98360_ALC5682I_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98360 ALC5682I.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + gpio_configure_pads(bt_i2s_enable_pads, ARRAY_SIZE(bt_i2s_enable_pads)); + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98360_ALC5682I_VS_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98360 ALC5682I-VS.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + gpio_configure_pads(bt_i2s_enable_pads, ARRAY_SIZE(bt_i2s_enable_pads)); + } +} +BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL); diff --git a/src/mainboard/google/brya/variants/primus4es/gpio.c b/src/mainboard/google/brya/variants/primus4es/gpio.c new file mode 100644 index 0000000..df0930c --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/gpio.c @@ -0,0 +1,149 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/gpio.h> +#include <baseboard/variants.h> +#include <commonlib/helpers.h> +#include <soc/gpio.h> + +/* Pad configuration in ramstage */ +static const struct pad_config override_gpio_table[] = { + /* A6 : ESPI_ALERT1# ==> NC */ + PAD_NC(GPP_A6, NONE), + /* A7 : SRCCLK_OE7# ==> NC */ + PAD_NC(GPP_A7, NONE), + /* A14 : USB_OC1# ==> NC */ + PAD_NC(GPP_A14, NONE), + /* A15 : USB_OC2# ==> NC */ + PAD_NC(GPP_A15, NONE), + /* A21 : DDPC_CTRCLK ==> NC */ + PAD_NC(GPP_A21, NONE), + /* A22 : DDPC_CTRLDATA ==> NC */ + PAD_NC(GPP_A22, NONE), + + /* B3 : PROC_GP2 ==> eMMC_PERST_L */ + PAD_CFG_GPO(GPP_B3, 1, DEEP), + + /* C3 : SML0CLK ==> NC */ + PAD_NC(GPP_C3, NONE), + /* C4 : SML0DATA ==> NC */ + PAD_NC(GPP_C4, NONE), + + /* D3 : ISH_GP3 ==> M2_SSD_PLN_L */ + PAD_CFG_GPO(GPP_D3, 1, PLTRST), + /* D5 : SRCCLKREQ0# ==> SSD_CLKREQ_ODL */ + PAD_CFG_NF(GPP_D5, NONE, DEEP, NF1), + /* D6 : SRCCLKREQ1# ==> NC */ + PAD_NC(GPP_D6, NONE), + /* D13 : ISH_UART0_RXD ==> NC */ + PAD_NC(GPP_D13, NONE), + /* D14 : ISH_UART0_TXD ==> USB_A1_RT_RST_ODL */ + PAD_CFG_GPO(GPP_D14, 1, DEEP), + /* D18 : UART1_TXD ==> SD_PE_RST_L */ + PAD_CFG_GPO(GPP_D18, 1, PLTRST), + + /* E3 : PROC_GP0 ==> NC */ + PAD_NC(GPP_E3, NONE), + /* E7 : PROC_GP1 ==> NC */ + PAD_NC(GPP_E7, NONE), + + /* F19 : SRCCLKREQ6# ==> EMMC_CLKREQ_ODL */ + PAD_CFG_NF(GPP_F19, NONE, DEEP, NF1), + /* F20 : EXT_PWR_GATE# ==> NC */ + PAD_NC(GPP_F20, NONE), + + /* H19 : SRCCLKREQ4# ==> NC */ + PAD_NC(GPP_H19, NONE), + /* H21 : IMGCLKOUT2 ==> NC */ + PAD_NC(GPP_H21, NONE), + /* H22 : IMGCLKOUT3 ==> NC */ + PAD_NC(GPP_H22, NONE), + /* H23 : SRCCLKREQ5# ==> NC */ + PAD_NC(GPP_H23, NONE), + + /* S6 : SNDW3_CLK ==> NC */ + PAD_NC(GPP_S6, NONE), + /* S7 : SNDW3_DATA ==> NC */ + PAD_NC(GPP_S7, NONE), + + /* T2 : GPP_T2 ==> eMMC_CFG */ + PAD_CFG_GPI(GPP_T2, NONE, DEEP), + + /* GPD11: LANPHYC ==> NC */ + PAD_NC(GPD11, NONE), +}; + +/* Early pad configuration in bootblock */ +static const struct pad_config early_gpio_table[] = { + /* A12 : SATAXPCIE1 ==> EN_PPVAR_WWAN */ + PAD_CFG_GPO(GPP_A12, 1, DEEP), + /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */ + PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT), + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 0, DEEP), + /* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */ + PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2), + /* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */ + PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2), + /* + * D1 : ISH_GP1 ==> FP_RST_ODL + * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down. + * To ensure proper power sequencing for the FPMCU device, reset signal is driven low + * early on in bootblock, followed by enabling of power. Reset signal is deasserted + * later on in ramstage. Since reset signal is asserted in bootblock, it results in + * FPMCU not working after a S3 resume. This is a known issue. + */ + PAD_CFG_GPO(GPP_D1, 0, DEEP), + /* D2 : ISH_GP2 ==> EN_FP_PWR */ + PAD_CFG_GPO(GPP_D2, 1, DEEP), + /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */ + PAD_CFG_GPO(GPP_D11, 1, DEEP), + /* D18 : UART1_TXD ==> SD_PE_RST_L */ + PAD_CFG_GPO(GPP_D18, 0, PLTRST), + /* E0 : SATAXPCIE0 ==> WWAN_PERST_L (updated in ramstage)*/ + PAD_CFG_GPO(GPP_E0, 0, DEEP), + /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */ + PAD_CFG_GPI(GPP_E13, NONE, DEEP), + /* E16 : RSVD_TP ==> WWAN_RST_L (updated in ramstage)*/ + PAD_CFG_GPO(GPP_E16, 0, DEEP), + /* E15 : RSVD_TP ==> PCH_WP_OD */ + PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP), + /* E20 : USB_C1_LSX_SOC_TX ==> EN_PP3300_eMMC */ + PAD_CFG_GPO(GPP_E20, 1, DEEP), + /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (updated in romstage) */ + PAD_CFG_GPO(GPP_F21, 0, DEEP), + /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */ + PAD_CFG_GPI(GPP_F18, NONE, DEEP), + /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */ + PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2), + /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */ + PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2), + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_CFG_GPO(GPP_H13, 1, PLTRST), +}; + +static const struct pad_config romstage_gpio_table[] = { + /* A12 : SATAXPCIE1 ==> EN_PPVAR_WWAN (set here for correct power sequencing) */ + PAD_CFG_GPO(GPP_A12, 1, DEEP), + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 1, DEEP), + /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (set here for correct power sequencing) */ + PAD_CFG_GPO(GPP_F21, 1, DEEP), +}; + +const struct pad_config *variant_gpio_override_table(size_t *num) +{ + *num = ARRAY_SIZE(override_gpio_table); + return override_gpio_table; +} + +const struct pad_config *variant_early_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(early_gpio_table); + return early_gpio_table; +} + +const struct pad_config *variant_romstage_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(romstage_gpio_table); + return romstage_gpio_table; +} diff --git a/src/mainboard/google/brya/variants/primus4es/include/variant/ec.h b/src/mainboard/google/brya/variants/primus4es/include/variant/ec.h new file mode 100644 index 0000000..7309098 --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/include/variant/ec.h @@ -0,0 +1,11 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __VARIANT_EC_H__ +#define __VARIANT_EC_H__ + +#include <baseboard/ec.h> + +/* Enable PS/2 Mouse */ +#define SIO_EC_ENABLE_PS2M + +#endif diff --git a/src/mainboard/google/brya/variants/primus4es/include/variant/gpio.h b/src/mainboard/google/brya/variants/primus4es/include/variant/gpio.h new file mode 100644 index 0000000..cbf6040 --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/include/variant/gpio.h @@ -0,0 +1,13 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef VARIANT_GPIO_H +#define VARIANT_GPIO_H + +#include <baseboard/gpio.h> +#define WWAN_FCPO GPP_F21 +#define WWAN_RST GPP_E16 +#define WWAN_PERST GPP_E0 +#define T1_OFF_MS 16 +#define T2_OFF_MS 2 + +#endif diff --git a/src/mainboard/google/brya/variants/primus4es/memory/Makefile.inc b/src/mainboard/google/brya/variants/primus4es/memory/Makefile.inc new file mode 100644 index 0000000..d2fae29 --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/memory/Makefile.inc @@ -0,0 +1,9 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/primus/memory src/mainboard/google/brya/variants/primus/memory/mem_parts_used.txt + +SPD_SOURCES = +SPD_SOURCES += spd/lp4x/set-0/spd-1.hex # ID = 0(0b0000) Parts = H9HCNNNBKMMLXR-NEE, K4U6E3S4AA-MGCR, MT53E512M32D1NP-046 WT:B +SPD_SOURCES += spd/lp4x/set-0/spd-2.hex # ID = 1(0b0001) Parts = H9HCNNNFAMMLXR-NEE +SPD_SOURCES += spd/lp4x/set-0/spd-3.hex # ID = 2(0b0010) Parts = H9HCNNNCPMMLXR-NEE, MT53E1G32D2NP-046 WT:B, K4UBE3D4AA-MGCR diff --git a/src/mainboard/google/brya/variants/primus4es/memory/dram_id.generated.txt b/src/mainboard/google/brya/variants/primus4es/memory/dram_id.generated.txt new file mode 100644 index 0000000..cdaaac0 --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/memory/dram_id.generated.txt @@ -0,0 +1,13 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/primus/memory src/mainboard/google/brya/variants/primus/memory/mem_parts_used.txt + +DRAM Part Name ID to assign +H9HCNNNBKMMLXR-NEE 0 (0000) +H9HCNNNFAMMLXR-NEE 1 (0001) +H9HCNNNCPMMLXR-NEE 2 (0010) +K4U6E3S4AA-MGCR 0 (0000) +MT53E512M32D1NP-046 WT:B 0 (0000) +MT53E1G32D2NP-046 WT:B 2 (0010) +K4UBE3D4AA-MGCR 2 (0010) diff --git a/src/mainboard/google/brya/variants/primus4es/memory/mem_parts_used.txt b/src/mainboard/google/brya/variants/primus4es/memory/mem_parts_used.txt new file mode 100644 index 0000000..bb14464 --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/memory/mem_parts_used.txt @@ -0,0 +1,7 @@ +H9HCNNNBKMMLXR-NEE +H9HCNNNFAMMLXR-NEE +H9HCNNNCPMMLXR-NEE +K4U6E3S4AA-MGCR +MT53E512M32D1NP-046 WT:B +MT53E1G32D2NP-046 WT:B +K4UBE3D4AA-MGCR diff --git a/src/mainboard/google/brya/variants/primus4es/overridetree.cb b/src/mainboard/google/brya/variants/primus4es/overridetree.cb new file mode 100644 index 0000000..c12939f --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/overridetree.cb @@ -0,0 +1,390 @@ +fw_config + field DB_USB 0 3 + option USB_ABSENT 0 + option USB3_PS8811 1 + end + field DB_SD 4 5 + option SD_ABSENT 0 + option SD_GL9755S 1 + end + field KB_BL 7 7 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field AUDIO 8 10 + option AUDIO_UNKNOWN 0 + option MAX98360_ALC5682I_I2S 1 + option MAX98360_ALC5682I_VS_I2S 2 + end + field DB_LTE 11 12 + option LTE_ABSENT 0 + option LTE_USB 1 + end +end + +chip soc/intel/alderlake + # This disabled autonomous GPIO power management, otherwise + # old cr50 FW only supports short pulses; need to clarify + # the minimum PCH IRQ pulse width with Intel, b/180111628 + register "gpio_override_pm" = "1" + register "gpio_pm[COMM_0]" = "0" + register "gpio_pm[COMM_1]" = "0" + register "gpio_pm[COMM_2]" = "0" + register "gpio_pm[COMM_3]" = "0" + register "gpio_pm[COMM_4]" = "0" + register "gpio_pm[COMM_5]" = "0" + register "SaGv" = "SaGv_Enabled" + register "MaxDramSpeed" = "3733" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI1 | Fingerprint MCU | + #| I2C0 | Audio | + #| I2C1 | Touchscreen | + #| I2C2 | | + #| I2C3 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[3] = { + .early_init = 1, + .speed = I2C_SPEED_FAST, + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + }, + }" + + register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable USB2_C1 + register "usb2_ports[7]" = "USB2_PORT_MID(OC_SKIP)" # Type-A MLB Port + register "usb3_ports[1]" = "USB3_PORT_DEFAULT(OC_SKIP)" # USB3/2 Type A MLB port + register "usb3_ports[2]" = "USB3_PORT_EMPTY" + register "usb2_ports[5]" = "USB2_PORT_MID(OC_SKIP)" + + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""SSD"" + register "options.tsr[1].desc" = ""CHARGER"" + register "options.tsr[2].desc" = ""MEMORY"" + register "options.tsr[3].desc" = ""TYPEC"" + # TODO: below values are initial reference values only + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 90, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 90, 5000), + [3] = DPTF_PASSIVE(CPU, TEMP_SENSOR_2, 90, 5000), + [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 90, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 89, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 85, SHUTDOWN), + [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 3000, + .max_power = 15000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 250, + }, + .pl2 = { + .min_power = 55000, + .max_power = 55000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + device generic 0 alias dptf_policy on end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end + device ref pcie_rp3 on + chip soc/intel/common/block/pcie/rtd3 + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B3)" + register "srcclk_pin" = "6" + device generic 0 alias emmc_rtd3 on end + end + # Enable PCIe-to-eMMC bridge PCIE 3 using clk 6 + register "pch_pcie_rp[PCH_RP(3)]" = "{ + .clk_src = 6, + .clk_req = 6, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + end #PCIE3 BH799BB + device ref tcss_dma0 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port1 as dfp[0].typec_port + device generic 0 on end + end + end + device ref tcss_dma1 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port3 as dfp[0].typec_port + device generic 0 on end + end + end + device ref pcie_rp6 off end #PCIE6 WWAN + device ref pcie_rp8 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" + register "srcclk_pin" = "3" + device generic 0 on end + end + end #PCIE8 SD card + device ref pcie_rp9 on + # Enable NVMe PCIE 9 using clk 0 + register "pch_pcie_rp[PCH_RP(9)]" = "{ + .clk_src = 0, + .clk_req = 0, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + end #PCIE9-12 SSD + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a alias audio_codec on + probe AUDIO MAX98360_ALC5682I_I2S + probe AUDIO MAX98360_ALC5682I_VS_I2S + end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN9050"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "300" + register "generic.reset_off_delay_ms" = "1" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "6" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 0x10 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""GTCH7503"" + register "generic.desc" = ""G2TOUCH Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "50" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 0x40 on end + end + end + device ref i2c3 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""GXTP7288"" + register "generic.desc" = ""Goodix Touchpad"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.probed" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 2c on end + end + end + device ref hda on + chip drivers/generic/max98357a + register "hid" = ""MX98360A"" + register "sdmode_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + register "sdmode_delay" = "5" + device generic 0 on + probe AUDIO MAX98360_ALC5682I_I2S + probe AUDIO MAX98360_ALC5682I_VS_I2S + end + end + end + device ref gspi1 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" + register "wake" = "GPE0_DW2_15" + device spi 0 on end + end # FPMCU + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "1" + register "usb3_port_number" = "1" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "3" + register "usb3_port_number" = "3" + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C2 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C2 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port8 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (DB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb2_port9 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (DB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb3_port2 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port4 on end + end + end + end + end + end +end diff --git a/src/mainboard/google/brya/variants/primus4es/variant.c b/src/mainboard/google/brya/variants/primus4es/variant.c new file mode 100644 index 0000000..4c2458a --- /dev/null +++ b/src/mainboard/google/brya/variants/primus4es/variant.c @@ -0,0 +1,62 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <baseboard/variants.h> +#include <boardid.h> +#include <device/device.h> +#include <drivers/i2c/hid/chip.h> +#include <fw_config.h> +#include <gpio.h> +#include <soc/gpio.h> + +static void devtree_update_emmc_rtd3(uint32_t board_ver) +{ + struct device *emmc_rtd3 = DEV_PTR(emmc_rtd3); + if (board_ver > 1) + return; + + emmc_rtd3->enabled = 0; +} + +static void devtree_update_audio_codec(uint32_t board_ver) +{ + struct device *audio_codec = DEV_PTR(audio_codec); + struct drivers_i2c_generic_config *config = audio_codec->chip_info; + + if (board_ver <= 1) + return; + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98360_ALC5682I_VS_I2S))) + config->hid = "RTL5682"; +} + +static const struct pad_config nvme_disable_pads[] = { + PAD_NC(GPP_B2, NONE), /* B2 : VRALERT# ==> M2_SSD_PLA_L */ + PAD_NC(GPP_B4, NONE), /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_NC(GPP_D3, NONE), /* D3 : ISH_GP3 ==> M2_SSD_PLN_L */ + PAD_NC(GPP_D5, NONE), /* D5 : SRCCLKREQ0# ==> SSD_CLKREQ_ODL */ + PAD_NC(GPP_D11, NONE), /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */ +}; + +static const struct pad_config emmc_disable_pads[] = { + PAD_NC(GPP_B3, NONE), /* B3 : PROC_GP2 ==> eMMC_PERST_L */ + PAD_NC(GPP_E20, NONE), /* E20 : USB_C1_LSX_SOC_TX ==> EN_PP3300_eMMC */ + PAD_NC(GPP_F19, NONE), /* F19 : SRCCLKREQ6# ==> EMMC_CLKREQ_ODL */ +}; + +static void disable_unused_gpios(void) +{ + int emmc_detected = gpio_get(GPP_T2); + + if (emmc_detected == 1) + gpio_configure_pads(nvme_disable_pads, ARRAY_SIZE(nvme_disable_pads)); + else + gpio_configure_pads(emmc_disable_pads, ARRAY_SIZE(emmc_disable_pads)); +} + +void variant_devtree_update(void) +{ + uint32_t board_ver = board_id(); + disable_unused_gpios(); + devtree_update_emmc_rtd3(board_ver); + devtree_update_audio_codec(board_ver); +} diff --git a/src/mainboard/google/brya/variants/redrix4es/Makefile.inc b/src/mainboard/google/brya/variants/redrix4es/Makefile.inc new file mode 100644 index 0000000..446d113 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/Makefile.inc @@ -0,0 +1,10 @@ +# SPDX-License-Identifier: GPL-2.0-only +bootblock-y += gpio.c + +romstage-y += gpio.c + +ramstage-y += gpio.c + +ramstage-$(CONFIG_FW_CONFIG) += fw_config.c + +ramstage-y += variant.c diff --git a/src/mainboard/google/brya/variants/redrix4es/fw_config.c b/src/mainboard/google/brya/variants/redrix4es/fw_config.c new file mode 100644 index 0000000..ac31d99 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/fw_config.c @@ -0,0 +1,69 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <fw_config.h> +#include <gpio.h> + +static const struct pad_config dmic_enable_pads[] = { + PAD_CFG_NF(GPP_R4, NONE, DEEP, NF3), /* DMIC_CLK0_R */ + PAD_CFG_NF(GPP_R5, NONE, DEEP, NF3), /* DMIC_DATA0_R */ + +}; + +static const struct pad_config dmic_disable_pads[] = { + PAD_NC(GPP_R4, NONE), + PAD_NC(GPP_R5, NONE), +}; + +static const struct pad_config i2s_enable_pads[] = { + PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK_R */ + PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM_R */ + PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */ + PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */ + PAD_CFG_NF(GPP_S0, NONE, DEEP, NF4), /* I2S_SPKR_SCLK_R */ + PAD_CFG_NF(GPP_S1, NONE, DEEP, NF4), /* I2S_SPKR_SFRM_R */ + PAD_CFG_NF(GPP_S2, NONE, DEEP, NF4), /* I2S_PCH_TX_SPKR_RX_R */ + PAD_CFG_NF(GPP_S3, NONE, DEEP, NF4), /* I2S_PCH_RX_SPKR_TX */ +}; + +static const struct pad_config i2s_disable_pads[] = { + PAD_NC(GPP_R0, NONE), + PAD_NC(GPP_R1, NONE), + PAD_NC(GPP_R2, NONE), + PAD_NC(GPP_R3, NONE), + PAD_NC(GPP_S0, NONE), + PAD_NC(GPP_S1, NONE), + PAD_NC(GPP_S2, NONE), + PAD_NC(GPP_S3, NONE), +}; + +static const struct pad_config bt_i2s_enable_pads[] = { + PAD_CFG_NF(GPP_VGPIO_30, NONE, DEEP, NF3), /* BT_I2S_BCLK */ + PAD_CFG_NF(GPP_VGPIO_31, NONE, DEEP, NF3), /* BT_I2S_SYNC */ + PAD_CFG_NF(GPP_VGPIO_32, NONE, DEEP, NF3), /* BT_I2S_SDO */ + PAD_CFG_NF(GPP_VGPIO_33, NONE, DEEP, NF3), /* BT_I2S_SDI */ + PAD_CFG_NF(GPP_VGPIO_34, NONE, DEEP, NF1), /* SSP2_SCLK */ + PAD_CFG_NF(GPP_VGPIO_35, NONE, DEEP, NF1), /* SSP2_SFRM */ + PAD_CFG_NF(GPP_VGPIO_36, NONE, DEEP, NF1), /* SSP_TXD */ + PAD_CFG_NF(GPP_VGPIO_37, NONE, DEEP, NF1), /* SSP_RXD */ +}; + +static void fw_config_handle(void *unused) +{ + if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) { + printk(BIOS_INFO, "Disable audio related GPIO pins.\n"); + gpio_configure_pads(i2s_disable_pads, ARRAY_SIZE(i2s_disable_pads)); + gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads)); + return; + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98390_ALC5682I_I2S_4SPK))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98390 ALC5682I.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + printk(BIOS_INFO, "BT offload enabled\n"); + gpio_configure_pads(bt_i2s_enable_pads, ARRAY_SIZE(bt_i2s_enable_pads)); + } +} +BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL); diff --git a/src/mainboard/google/brya/variants/redrix4es/gpio.c b/src/mainboard/google/brya/variants/redrix4es/gpio.c new file mode 100644 index 0000000..afcb7e9 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/gpio.c @@ -0,0 +1,150 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/gpio.h> +#include <baseboard/variants.h> +#include <commonlib/helpers.h> +#include <soc/gpio.h> + +/* Pad configuration in ramstage */ +static const struct pad_config override_gpio_table[] = { + /* A17 : DISP_MISCC ==> NC */ + PAD_NC(GPP_A17, NONE), + /* A19 : DDSP_HPD1 ==> NC */ + PAD_NC(GPP_A19, NONE), + /* A20 : DDSP_HPD2 ==> NC */ + PAD_NC(GPP_A20, NONE), + /* A21 : DDPC_CTRCLK ==> NC */ + PAD_NC(GPP_A21, NONE), + /* A22 : DDPC_CTRLDATA ==> NC */ + PAD_NC(GPP_A22, NONE), + + /* B3 : PROC_GP2 ==> NC */ + PAD_NC(GPP_B3, NONE), + /* B15 : TIME_SYNC0 ==> NC */ + PAD_NC(GPP_B15, NONE), + + /* C3 : SML0CLK ==> NC */ + PAD_NC(GPP_C3, NONE), + /* C4 : SML0DATA ==> NC */ + PAD_NC(GPP_C4, NONE), + + /* D7 : SRCCLKREQ2# ==> NC */ + PAD_NC(GPP_D7, NONE), + /* D13 : ISH_UART0_RXD ==> NC */ + PAD_NC(GPP_D13, NONE), + + /* E3 : PROC_GP0 ==> NC */ + PAD_NC(GPP_E3, NONE), + /* E7 : PROC_GP1 ==> NC */ + PAD_NC(GPP_E7, NONE), + /* E16 : RSVD_TP ==> WWAN_RST_L */ + PAD_CFG_GPO(GPP_E16, 1, DEEP), + /* E20 : DDP2_CTRLCLK ==> NC */ + PAD_NC(GPP_E20, NONE), + /* E22 : DDPA_CTRLCLK ==> NC */ + PAD_NC(GPP_E22, NONE), + /* E23 : DDPA_CTRLDATA ==> NC */ + PAD_NC(GPP_E23, NONE), + /* F20 : EXT_PWR_GATE# ==> NC */ + PAD_NC(GPP_F20, NONE), + + /* H3 : SX_EXIT_HOLDOFF# ==> NC */ + PAD_NC(GPP_H3, NONE), + /* H20 : IMGCLKOUT1 ==> NC */ + PAD_NC(GPP_H20, NONE), + /* H21 : IMGCLKOUT2 ==> Privacy screen */ + PAD_CFG_GPO(GPP_H21, 0, DEEP), + + /* R6 : I2S_PCH_TX_SPKR_RX ==> NC */ + PAD_NC(GPP_R6, NONE), + /* R7 : I2S_PCH_RX_SPKR_TX ==> NC */ + PAD_NC(GPP_R7, NONE), + + /* S4 : SNDW2_CLK ==> NC */ + PAD_NC(GPP_S4, NONE), + /* S5 : SNDW2_DATA ==> NC */ + PAD_NC(GPP_S5, NONE), + /* S6 : SNDW3_CLK ==> NC */ + PAD_NC(GPP_S6, NONE), + /* S7 : SNDW3_DATA ==> NC */ + PAD_NC(GPP_S7, NONE), + /* + * E0 : SATAXPCIE0 ==> WWAN_PERST_L + * Drive high here, so that PERST_L is sequenced after RST_L + */ + PAD_CFG_GPO(GPP_E0, 1, DEEP), +}; + +/* Early pad configuration in bootblock */ +static const struct pad_config early_gpio_table[] = { + /* A12 : SATAXPCIE1 ==> EN_PP3300_WWAN */ + PAD_CFG_GPO(GPP_A12, 1, DEEP), + /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */ + PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT), + /* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */ + PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2), + /* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */ + PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2), + /* + * D1 : ISH_GP1 ==> FP_RST_ODL + * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down. + * To ensure proper power sequencing for the FPMCU device, reset signal is driven low + * early on in bootblock, followed by enabling of power. Reset signal is deasserted + * later on in ramstage. Since reset signal is asserted in bootblock, it results in + * FPMCU not working after a S3 resume. This is a known issue. + */ + PAD_CFG_GPO(GPP_D1, 0, DEEP), + /* D2 : ISH_GP2 ==> EN_FP_PWR */ + PAD_CFG_GPO(GPP_D2, 1, DEEP), + /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */ + PAD_CFG_GPO(GPP_D11, 1, DEEP), + /* E0 : SATAXPCIE0 ==> WWAN_PERST_L (updated in ramstage) */ + PAD_CFG_GPO(GPP_E0, 0, DEEP), + /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */ + PAD_CFG_GPI(GPP_E13, NONE, DEEP), + /* E15 : RSVD_TP ==> PCH_WP_OD */ + PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP), + /* E16 : RSVD_TP ==> WWAN_RST_L (updated in ramstage) */ + PAD_CFG_GPO(GPP_E16, 0, DEEP), + /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */ + PAD_CFG_GPI(GPP_F18, NONE, DEEP), + /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (updated in romstage) */ + PAD_CFG_GPO(GPP_F21, 0, DEEP), + /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */ + PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2), + /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */ + PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2), + /* + * enable EN_PP3300_SSD in bootblock, then PERST# is asserted, and + * then deassert PERST# in romstage + */ + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_CFG_GPO(GPP_H13, 1, DEEP), + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 0, DEEP), +}; + +static const struct pad_config romstage_gpio_table[] = { + /* B4 : PROC_GP3 ==> SSD_PERST_L */ + PAD_CFG_GPO(GPP_B4, 1, DEEP), + /* F21 : EXT_PWR_GATE2# ==> WWAN_FCPO_L (set here for correct power sequencing) */ + PAD_CFG_GPO(GPP_F21, 1, DEEP), +}; + +const struct pad_config *variant_gpio_override_table(size_t *num) +{ + *num = ARRAY_SIZE(override_gpio_table); + return override_gpio_table; +} + +const struct pad_config *variant_early_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(early_gpio_table); + return early_gpio_table; +} + +const struct pad_config *variant_romstage_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(romstage_gpio_table); + return romstage_gpio_table; +} diff --git a/src/mainboard/google/brya/variants/redrix4es/include/variant/ec.h b/src/mainboard/google/brya/variants/redrix4es/include/variant/ec.h new file mode 100644 index 0000000..6f104d5 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/include/variant/ec.h @@ -0,0 +1,11 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __VARIANT_EC_H__ +#define __VARIANT_EC_H__ + +#include <baseboard/ec.h> + +/* Enable EC backed Keyboard Backlight in ACPI */ +#define EC_ENABLE_KEYBOARD_BACKLIGHT + +#endif diff --git a/src/mainboard/google/brya/variants/redrix4es/include/variant/gpio.h b/src/mainboard/google/brya/variants/redrix4es/include/variant/gpio.h new file mode 100644 index 0000000..99d09b2 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/include/variant/gpio.h @@ -0,0 +1,14 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef VARIANT_GPIO_H +#define VARIANT_GPIO_H + +#include <baseboard/gpio.h> + +#define WWAN_FCPO GPP_F21 +#define WWAN_RST GPP_E16 +#define WWAN_PERST GPP_E0 +#define T1_OFF_MS 16 +#define T2_OFF_MS 2 + +#endif diff --git a/src/mainboard/google/brya/variants/redrix4es/memory/Makefile.inc b/src/mainboard/google/brya/variants/redrix4es/memory/Makefile.inc new file mode 100644 index 0000000..8590598 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/memory/Makefile.inc @@ -0,0 +1,11 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/redrix/memory src/mainboard/google/brya/variants/redrix/memory/mem_parts_used.txt + +SPD_SOURCES = +SPD_SOURCES += spd/lp4x/set-0/spd-4.hex # ID = 0(0b0000) Parts = MT53E1G32D2NP-046 WT:A +SPD_SOURCES += spd/lp4x/set-0/spd-1.hex # ID = 1(0b0001) Parts = H9HCNNNBKMMLXR-NEE, K4U6E3S4AA-MGCR, MT53E512M32D2NP-046 WT:E, MT53E512M32D1NP-046 WT:B +SPD_SOURCES += spd/lp4x/set-0/spd-3.hex # ID = 2(0b0010) Parts = H9HCNNNCPMMLXR-NEE, K4UBE3D4AA-MGCR, MT53E1G32D2NP-046 WT:B +SPD_SOURCES += spd/lp4x/set-0/spd-2.hex # ID = 3(0b0011) Parts = H9HCNNNFAMMLXR-NEE +SPD_SOURCES += spd/lp4x/set-0/spd-7.hex # ID = 4(0b0100) Parts = MT53E2G32D4NQ-046 WT:A diff --git a/src/mainboard/google/brya/variants/redrix4es/memory/dram_id.generated.txt b/src/mainboard/google/brya/variants/redrix4es/memory/dram_id.generated.txt new file mode 100644 index 0000000..296634a --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/memory/dram_id.generated.txt @@ -0,0 +1,16 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/redrix/memory src/mainboard/google/brya/variants/redrix/memory/mem_parts_used.txt + +DRAM Part Name ID to assign +MT53E1G32D2NP-046 WT:A 0 (0000) +H9HCNNNBKMMLXR-NEE 1 (0001) +K4U6E3S4AA-MGCR 1 (0001) +MT53E512M32D2NP-046 WT:E 1 (0001) +H9HCNNNCPMMLXR-NEE 2 (0010) +K4UBE3D4AA-MGCR 2 (0010) +H9HCNNNFAMMLXR-NEE 3 (0011) +MT53E2G32D4NQ-046 WT:A 4 (0100) +MT53E512M32D1NP-046 WT:B 1 (0001) +MT53E1G32D2NP-046 WT:B 2 (0010) diff --git a/src/mainboard/google/brya/variants/redrix4es/memory/mem_parts_used.txt b/src/mainboard/google/brya/variants/redrix4es/memory/mem_parts_used.txt new file mode 100644 index 0000000..71bd5fd --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/memory/mem_parts_used.txt @@ -0,0 +1,10 @@ +MT53E1G32D2NP-046 WT:A +H9HCNNNBKMMLXR-NEE +K4U6E3S4AA-MGCR +MT53E512M32D2NP-046 WT:E +H9HCNNNCPMMLXR-NEE +K4UBE3D4AA-MGCR +H9HCNNNFAMMLXR-NEE +MT53E2G32D4NQ-046 WT:A +MT53E512M32D1NP-046 WT:B +MT53E1G32D2NP-046 WT:B diff --git a/src/mainboard/google/brya/variants/redrix4es/overridetree.cb b/src/mainboard/google/brya/variants/redrix4es/overridetree.cb new file mode 100644 index 0000000..67cb7f3 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/overridetree.cb @@ -0,0 +1,523 @@ +fw_config + field DB_SD 0 1 + option SD_ABSENT 0 + option SD_GL9755S 1 + end + field KB_BL 2 2 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field AUDIO 3 5 + option AUDIO_UNKNOWN 0 + option MAX98390_ALC5682I_I2S_4SPK 1 + end + field DB_LTE 6 7 + option LTE_ABSENT 0 + option LTE_USB 1 + option LTE_PCIE 2 + end + field EPS 10 10 + option PRIVACY_SCREEN_ABSENT 0 + option PRIVACY_SCREEN 1 + end + field CAMERA_UFC 38 39 + option CAMERA_NONE 0 + option CAMERA_OV5675 1 + option CAMERA_HI556 2 + end + field TP_SOURCE 40 41 + option ELAN0000 0 + option ELAN2703 1 + end +end +chip soc/intel/alderlake + # This disables autonomous GPIO power management, otherwise + # old cr50 FW only supports short pulses; need to clarify + # the minimum PCH IRQ pulse width with Intel, b/180111628 + register "gpio_override_pm" = "1" + register "gpio_pm[COMM_0]" = "0" + register "gpio_pm[COMM_1]" = "0" + register "gpio_pm[COMM_2]" = "0" + register "gpio_pm[COMM_3]" = "0" + register "gpio_pm[COMM_4]" = "0" + register "gpio_pm[COMM_5]" = "0" + register "SaGv" = "SaGv_Enabled" + register "CnviBtAudioOffload" = "true" + # FIVR RFI Spread Spectrum 6% + register "FivrSpreadSpectrum" = "FIVR_SS_6" + + # Acoustic settings + register "AcousticNoiseMitigation" = "1" + register "SlowSlewRate[VR_DOMAIN_IA]" = "SLEW_FAST_8" + register "FastPkgCRampDisable[VR_DOMAIN_IA]" = "1" + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI1 | Fingerprint MCU | + #| I2C0 | Audio | + #| I2C1 | Touchscreen | + #| I2C2 | | + #| I2C3 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[3] = { + .early_init = 1, + .speed = I2C_SPEED_FAST, + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + }, + }" + device domain 0 on + device ref igpu on + chip drivers/gfx/generic + register "device_count" = "1" + register "device[0].name" = ""LCD"" + # Internal panel on the first port of the graphics chip + register "device[0].addr" = "0x80010400" + register "device[0].privacy.enabled" = "1" + register "device[0].privacy.gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H21)" + device generic 0 on + probe EPS PRIVACY_SCREEN + end + end + end # Integrated Graphics Device + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DRAM"" + register "options.tsr[1].desc" = ""SOC"" + register "options.tsr[2].desc" = ""Charger"" + register "options.tsr[3].desc" = ""5V regulator"" + + # TODO: below values are initial reference values only + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 55, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 45, 5000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 51, 5000), + [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 51, 5000), + [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 51, 5000), + }" + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 13000, + .max_power = 15000, + .time_window_min = 42 * MSECS_PER_SEC, + .time_window_max = 42 * MSECS_PER_SEC, + .granularity = 200, + }, + .pl2 = { + .min_power = 35000, + .max_power = 35000, + .time_window_min = 42 * MSECS_PER_SEC, + .time_window_max = 42 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + device generic 0 alias dptf_policy on end + end + end + device ref ipu on + chip drivers/intel/mipi_camera + register "acpi_uid" = "0x50000" + register "acpi_name" = ""IPU0"" + register "device_type" = "INTEL_ACPI_CAMERA_CIO2" + + register "cio2_num_ports" = "1" + register "cio2_lanes_used" = "{2}" # 2 CSI Camera lanes are used + register "cio2_lane_endpoint[0]" = ""^I2C2.CAM0"" + register "cio2_prt[0]" = "2" + device generic 0 on end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end + device ref pcie_rp6 on + probe DB_LTE LTE_PCIE + end + device ref tcss_dma0 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port1 as dfp[0].typec_port + device generic 0 on end + end + end + device ref tcss_dma1 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port3 as dfp[0].typec_port + device generic 0 on end + end + end + device ref pcie_rp8 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" + register "srcclk_pin" = "3" + device generic 0 on end + end + end #PCIE8 SD card + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO MAX98390_ALC5682I_I2S_4SPK + end + end + chip drivers/i2c/max98390 + register "desc" = ""MAX98390 Speaker Amp 0"" + register "uid" = "0" + register "name" = ""MXW0"" + register "r0_calib_key" = ""dsm_calib_r0_0"" + register "temperature_calib_key" = ""dsm_calib_temp_0"" + register "dsm_param_file_name" = ""dsm_param_R"" + register "vmon_slot_no" = "0" + register "imon_slot_no" = "1" + device i2c 0x3a on + probe AUDIO MAX98390_ALC5682I_I2S_4SPK + end + end + chip drivers/i2c/max98390 + register "desc" = ""MAX98390 Speaker Amp 1"" + register "uid" = "1" + register "name" = ""MXW1"" + register "r0_calib_key" = ""dsm_calib_r0_1"" + register "temperature_calib_key" = ""dsm_calib_temp_1"" + register "dsm_param_file_name" = ""dsm_param_L"" + register "vmon_slot_no" = "1" + register "imon_slot_no" = "0" + device i2c 0x3b on + probe AUDIO MAX98390_ALC5682I_I2S_4SPK + end + end + chip drivers/i2c/max98390 + register "desc" = ""MAX98390 Speaker Amp 2"" + register "uid" = "2" + register "name" = ""MXW2"" + register "r0_calib_key" = ""dsm_calib_r0_2"" + register "temperature_calib_key" = ""dsm_calib_temp_2"" + register "dsm_param_file_name" = ""dsm_param_tt_R"" + register "vmon_slot_no" = "2" + register "imon_slot_no" = "3" + device i2c 0x38 on + probe AUDIO MAX98390_ALC5682I_I2S_4SPK + end + end + chip drivers/i2c/max98390 + register "desc" = ""MAX98390 Speaker Amp 3"" + register "uid" = "3" + register "name" = ""MXW3"" + register "r0_calib_key" = ""dsm_calib_r0_3"" + register "temperature_calib_key" = ""dsm_calib_temp_3"" + register "dsm_param_file_name" = ""dsm_param_tt_L"" + register "vmon_slot_no" = "3" + register "imon_slot_no" = "2" + device i2c 0x39 on + probe AUDIO MAX98390_ALC5682I_I2S_4SPK + end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN2513"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "300" + register "generic.reset_off_delay_ms" = "1" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "6" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 0x15 on end + end + end + device ref i2c2 on + chip drivers/intel/mipi_camera + register "acpi_hid" = ""OVTI5675"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM0"" + register "chip_name" = ""Ov 5675 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + + register "ssdb.lanes_used" = "2" + register "ssdb.link_used" = "1" + register "num_freq_entries" = "1" + register "link_freq[0]" = "DEFAULT_LINK_FREQ" + register "remote_name" = ""IPU0"" + register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" + + register "has_power_resource" = "1" + #Controls + register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" + register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" + + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #EN_UCAM_LED_PWR + register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" #EN_UCAM_PWR + register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" #reset + + #_ON + register "on_seq.ops_cnt" = "5" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" + register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" + + #_OFF + register "off_seq.ops_cnt" = "4" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + device i2c 36 on + probe CAMERA_UFC CAMERA_NONE + probe CAMERA_UFC CAMERA_OV5675 + end + end + chip drivers/intel/mipi_camera + register "acpi_hid" = ""INT3537"" + register "acpi_uid" = "0" + register "acpi_name" = ""CAM0"" + register "chip_name" = ""Hi-556 Camera"" + register "device_type" = "INTEL_ACPI_CAMERA_SENSOR" + register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D3_COLD" + + register "ssdb.lanes_used" = "2" + register "ssdb.link_used" = "1" + register "num_freq_entries" = "1" + register "link_freq[0]" = "437000000" + register "remote_name" = ""IPU0"" + + register "has_power_resource" = "1" + #Controls + register "clk_panel.clks[0].clknum" = "IMGCLKOUT_3" + register "clk_panel.clks[0].freq" = "FREQ_19_2_MHZ" + + register "gpio_panel.gpio[0].gpio_num" = "GPP_D15" #EN_UCAM_LED_PWR + register "gpio_panel.gpio[1].gpio_num" = "GPP_D16" #EN_UCAM_PWR + register "gpio_panel.gpio[2].gpio_num" = "GPP_D3" #reset + + #_ON + register "on_seq.ops_cnt" = "5" + register "on_seq.ops[0]" = "SEQ_OPS_CLK_ENABLE(0, 0)" + register "on_seq.ops[1]" = "SEQ_OPS_GPIO_ENABLE(0, 5)" + register "on_seq.ops[2]" = "SEQ_OPS_GPIO_ENABLE(1, 5)" + register "on_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(2, 5)" + register "on_seq.ops[4]" = "SEQ_OPS_GPIO_ENABLE(2, 5)" + + #_OFF + register "off_seq.ops_cnt" = "4" + register "off_seq.ops[0]" = "SEQ_OPS_CLK_DISABLE(0, 0)" + register "off_seq.ops[1]" = "SEQ_OPS_GPIO_DISABLE(2, 0)" + register "off_seq.ops[2]" = "SEQ_OPS_GPIO_DISABLE(1, 0)" + register "off_seq.ops[3]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + device i2c 20 on + probe CAMERA_UFC CAMERA_HI556 + end + end + chip drivers/intel/mipi_camera + register "acpi_hid" = "ACPI_DT_NAMESPACE_HID" + register "acpi_uid" = "1" + register "acpi_name" = ""NVM0"" + register "chip_name" = ""M24C64X"" + register "device_type" = "INTEL_ACPI_CAMERA_NVM" + register "max_dstate_for_probe" = "ACPI_DEVICE_SLEEP_D0" + + register "has_power_resource" = "1" + #Controls + register "gpio_panel.gpio[0].gpio_num" = "GPP_D16" #EN_UCAM_PWR + + #_ON + register "on_seq.ops_cnt" = "1" + register "on_seq.ops[0]" = "SEQ_OPS_GPIO_ENABLE(0, 0)" + + #_OFF + register "off_seq.ops_cnt" = "1" + register "off_seq.ops[0]" = "SEQ_OPS_GPIO_DISABLE(0, 0)" + + register "nvm_size" = "0x2000" + register "nvm_pagesize" = "1" + register "nvm_readonly" = "1" + register "nvm_width" = "0x10" + register "nvm_compat" = ""atmel,24c64"" + device i2c 50 on end + end + + end + device ref i2c3 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on + probe TP_SOURCE ELAN0000 + end + end + chip drivers/i2c/hid + register "generic.hid" = ""ELAN2703"" + register "generic.desc" = ""ELAN Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.probed" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 15 on + probe TP_SOURCE ELAN2703 + end + end + end + device ref gspi1 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" + register "wake" = "GPE0_DW2_15" + device spi 0 on end + end # FPMCU + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "1" + register "usb3_port_number" = "1" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "3" + register "usb3_port_number" = "3" + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C2 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C2 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port4 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port9 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 WWAN"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb3_port4 on end + end + end + end + end + end +end diff --git a/src/mainboard/google/brya/variants/redrix4es/variant.c b/src/mainboard/google/brya/variants/redrix4es/variant.c new file mode 100644 index 0000000..6a79780 --- /dev/null +++ b/src/mainboard/google/brya/variants/redrix4es/variant.c @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <sar.h> + +const char *get_wifi_sar_cbfs_filename(void) +{ + return "wifi_sar_0.hex"; +} diff --git a/src/mainboard/google/brya/variants/taeko4es/Makefile.inc b/src/mainboard/google/brya/variants/taeko4es/Makefile.inc new file mode 100644 index 0000000..478f362 --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/Makefile.inc @@ -0,0 +1,7 @@ +bootblock-y += gpio.c + +romstage-y += memory.c + +ramstage-y += gpio.c + +ramstage-$(CONFIG_FW_CONFIG) += fw_config.c diff --git a/src/mainboard/google/brya/variants/taeko4es/fw_config.c b/src/mainboard/google/brya/variants/taeko4es/fw_config.c new file mode 100644 index 0000000..5068f84 --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/fw_config.c @@ -0,0 +1,62 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <fw_config.h> +#include <gpio.h> + +static const struct pad_config dmic_enable_pads[] = { + PAD_CFG_NF(GPP_S2, NONE, DEEP, NF2), /* DMIC_CLK0_R */ + PAD_CFG_NF(GPP_S3, NONE, DEEP, NF2), /* DMIC_DATA0_R */ + +}; + +static const struct pad_config dmic_disable_pads[] = { + PAD_NC(GPP_S2, NONE), + PAD_NC(GPP_S3, NONE), +}; + +static const struct pad_config i2s_enable_pads[] = { + PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK_R */ + PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM_R */ + PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */ + PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */ + PAD_CFG_NF(GPP_R4, NONE, DEEP, NF2), /* I2S_SPKR_SCLK_R */ + PAD_CFG_NF(GPP_R5, NONE, DEEP, NF2), /* I2S_SPKR_SFRM_R */ + PAD_CFG_NF(GPP_R6, NONE, DEEP, NF2), /* I2S_PCH_TX_SPKR_RX_R */ + PAD_NC(GPP_R7, NONE), /* I2S_PCH_RX_SPKR_TX */ +}; + +static const struct pad_config i2s_disable_pads[] = { + PAD_NC(GPP_R0, NONE), + PAD_NC(GPP_R1, NONE), + PAD_NC(GPP_R2, NONE), + PAD_NC(GPP_R3, NONE), + PAD_NC(GPP_R4, NONE), + PAD_NC(GPP_R5, NONE), + PAD_NC(GPP_R6, NONE), + PAD_NC(GPP_R7, NONE), +}; + +static void fw_config_handle(void *unused) +{ + if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) { + printk(BIOS_INFO, "Disable audio related GPIO pins.\n"); + gpio_configure_pads(i2s_disable_pads, ARRAY_SIZE(i2s_disable_pads)); + gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads)); + return; + } + + if (fw_config_probe(FW_CONFIG(AUDIO, AUDIO_MAX98357_ALC5682I_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98357 ALC5682I.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + } + + if (fw_config_probe(FW_CONFIG(AUDIO, AUDIO_MAX98357_ALC5682I_VS_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98357 ALC5682I-VS.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + } +} +BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL); diff --git a/src/mainboard/google/brya/variants/taeko4es/gpio.c b/src/mainboard/google/brya/variants/taeko4es/gpio.c new file mode 100644 index 0000000..17018cd --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/gpio.c @@ -0,0 +1,210 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/gpio.h> +#include <baseboard/variants.h> +#include <commonlib/helpers.h> +#include <soc/gpio.h> + +/* Pad configuration in ramstage */ +static const struct pad_config override_gpio_table[] = { + /* A6 : ESPI_ALERT1# ==> NC */ + PAD_NC(GPP_A6, NONE), + /* A7 : SRCCLK_OE7# ==> NC */ + PAD_NC(GPP_A7, NONE), + /* A8 : SRCCLKREQ7# ==> NC */ + PAD_NC(GPP_A8, NONE), + /* A12 : SATAXPCIE1 ==> NC */ + PAD_NC(GPP_A12, NONE), + /* A14 : USB_OC1# ==> NC */ + PAD_NC(GPP_A14, NONE), + /* A15 : USB_OC2# ==> NC */ + PAD_NC(GPP_A15, NONE), + /* A18 : DDSP_HPDB ==> NC */ + PAD_NC(GPP_A18, NONE), + /* A19 : DDSP_HPD1 ==> NC */ + PAD_NC(GPP_A19, NONE), + /* A20 : DDSP_HPD2 ==> NC */ + PAD_NC(GPP_A20, NONE), + /* A21 : DDPC_CTRCLK ==> NC */ + PAD_NC(GPP_A21, NONE), + /* A22 : DDPC_CTRLDATA ==> NC */ + PAD_NC(GPP_A22, NONE), + + /* B2 : VRALERT# ==> NC */ + PAD_NC(GPP_B2, NONE), + /* B3 : PROC_GP2 ==> NC */ + PAD_NC(GPP_B3, NONE), + /* B15 : TIME_SYNC0 ==> NC */ + PAD_NC(GPP_B15, NONE), + + /* C3 : SML0CLK ==> NC */ + PAD_NC(GPP_C3, NONE), + /* C4 : SML0DATA ==> NC */ + PAD_NC(GPP_C4, NONE), + /* C6 : SML1CLK ==> NC */ + PAD_NC(GPP_C6, NONE), + + /* D3 : ISH_GP3 ==> NC */ + PAD_NC(GPP_D3, NONE), + /* D5 : SRCCLKREQ0# ==> SSD_CLKREQ_ODL */ + PAD_CFG_NF(GPP_D5, NONE, DEEP, NF1), + /* D9 : ISH_SPI_CS# ==> NC */ + PAD_NC(GPP_D9, NONE), + /* D10 : ISH_SPI_CLK ==> NC */ + PAD_NC(GPP_D10, NONE), + /* D13 : ISH_UART0_RXD ==> NC */ + PAD_NC(GPP_D13, NONE), + /* D14 : ISH_UART0_TXD ==> NC */ + PAD_NC(GPP_D14, NONE), + /* D15 : ISH_UART0_RTS# ==> NC */ + PAD_NC(GPP_D15, NONE), + /* D16 : ISH_UART0_CTS# ==> NC */ + PAD_NC(GPP_D16, NONE), + /* D17 : UART1_RXD ==> NC */ + PAD_NC(GPP_D17, NONE), + + /* E0 : SATAXPCIE0 ==> NC */ + PAD_NC(GPP_E0, NONE), + /* E4 : SATA_DEVSLP0 ==> NC */ + PAD_NC(GPP_E4, NONE), + /* E5 : SATA_DEVSLP1 ==> NC */ + PAD_NC(GPP_E5, NONE), + /* E10 : THC0_SPI1_CS# ==> NC */ + PAD_NC(GPP_E10, NONE), + /* E16 : RSVD_TP ==> NC */ + PAD_NC(GPP_E16, NONE), + /* E17 : THC0_SPI1_INT# ==> NC */ + PAD_NC(GPP_E17, NONE), + /* E18 : DDP1_CTRLCLK ==> NC */ + PAD_NC(GPP_E18, NONE), + /* E19 : DDP1_CTRLDATA ==> NC */ + PAD_NC(GPP_E19, NONE), + /* E20 : DDP2_CTRLCLK ==> NC */ + PAD_NC(GPP_E20, NONE), + /* E21 : DDP2_CTRLDATA ==> NC */ + PAD_NC(GPP_E21, NONE), + + /* F6 : CNV_PA_BLANKING ==> NC */ + PAD_NC(GPP_F6, NONE), + /* F19 : SRCCLKREQ6# ==> NC */ + PAD_NC(GPP_F19, NONE), + /* F20 : EXT_PWR_GATE# ==> NC */ + PAD_NC(GPP_F20, NONE), + /* F21 : EXT_PWR_GATE2# ==> NC */ + PAD_NC(GPP_F21, NONE), + /* F22 : VNN_CTRL ==> VNN_CTRL */ + PAD_CFG_NF(GPP_F22, NONE, DEEP, NF1), + /* F23 : BP105_CTRL ==> PP1050_CTRL */ + PAD_CFG_NF(GPP_F23, NONE, DEEP, NF1), + + /* H8 : I2C4_SDA ==> NC */ + PAD_NC(GPP_H8, NONE), + /* H9 : I2C4_SCL ==> NC */ + PAD_NC(GPP_H9, NONE), + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_CFG_GPO(GPP_H13, 1, DEEP), + /* H15 : DDPB_CTRLCLK ==> NC */ + PAD_NC(GPP_H15, NONE), + /* H17 : DDPB_CTRLDATA ==> NC */ + PAD_NC(GPP_H17, NONE), + /* H19 : SRCCLKREQ4# ==> NC */ + PAD_NC(GPP_H19, NONE), + /* H21 : IMGCLKOUT2 ==> NC */ + PAD_NC(GPP_H21, NONE), + /* H22 : IMGCLKOUT3 ==> NC */ + PAD_NC(GPP_H22, NONE), + /* H23 : SRCCLKREQ5# ==> NC */ + PAD_NC(GPP_H23, NONE), + + /* R7 : I2S2_RXD ==> NC */ + PAD_NC(GPP_R7, NONE), + + /* S0 : SNDW0_CLK ==> NC */ + PAD_NC(GPP_S0, NONE), + /* S1 : SNDW0_DATA ==> NC */ + PAD_NC(GPP_S1, NONE), + /* S4 : SNDW2_CLK ==> NC */ + PAD_NC(GPP_S4, NONE), + /* S5 : SNDW2_DATA ==> NC */ + PAD_NC(GPP_S5, NONE), + /* S6 : SNDW3_CLK ==> NC */ + PAD_NC(GPP_S6, NONE), + /* S7 : SNDW3_DATA ==> NC */ + PAD_NC(GPP_S7, NONE), + + /* GPD11: LANPHYC ==> WWAN_CONFIG1 */ + PAD_NC(GPD11, NONE), +}; + +/* Early pad configuration in bootblock */ +static const struct pad_config early_gpio_table[] = { + /* A13 : PMC_I2C_SCL ==> GSC_PCH_INT_ODL */ + PAD_CFG_GPI_APIC(GPP_A13, NONE, PLTRST, LEVEL, INVERT), + /* B7 : ISH_12C1_SDA ==> PCH_I2C_TPM_SDA */ + PAD_CFG_NF(GPP_B7, NONE, DEEP, NF2), + /* B8 : ISH_12C1_SCL ==> PCH_I2C_TPM_SCL */ + PAD_CFG_NF(GPP_B8, NONE, DEEP, NF2), + /* + * D1 : ISH_GP1 ==> FP_RST_ODL + * FP_RST_ODL comes out of reset as hi-z and does not have an external pull-down. + * To ensure proper power sequencing for the FPMCU device, reset signal is driven low + * early on in bootblock, followed by enabling of power. Reset signal is deasserted + * later on in ramstage. Since reset signal is asserted in bootblock, it results in + * FPMCU not working after a S3 resume. This is a known issue. + */ + PAD_CFG_GPO(GPP_D1, 0, DEEP), + /* D2 : ISH_GP2 ==> EN_FP_PWR */ + PAD_CFG_GPO(GPP_D2, 1, DEEP), + /* D11 : ISH_SPI_MISO ==> EN_PP3300_SSD */ + PAD_CFG_GPO(GPP_D11, 1, DEEP), + /* E13 : THC0_SPI1_IO2 ==> MEM_CH_SEL */ + PAD_CFG_GPI(GPP_E13, NONE, DEEP), + /* E15 : RSVD_TP ==> PCH_WP_OD */ + PAD_CFG_GPI_GPIO_DRIVER(GPP_E15, NONE, DEEP), + /* F18 : THC1_SPI2_INT# ==> EC_IN_RW_OD */ + PAD_CFG_GPI(GPP_F18, NONE, DEEP), + /* H10 : UART0_RXD ==> UART_PCH_RX_DBG_TX */ + PAD_CFG_NF(GPP_H10, NONE, DEEP, NF2), + /* H11 : UART0_TXD ==> UART_PCH_TX_DBG_RX */ + PAD_CFG_NF(GPP_H11, NONE, DEEP, NF2), + /* H13 : I2C7_SCL ==> EN_PP3300_SD */ + PAD_CFG_GPO(GPP_H13, 1, DEEP), + /* + * B4 : PROC_GP3 ==> SSD_PERST_L + * B4 is programmed here so that it is sequenced after EN_PP3300_SSD. + */ + PAD_CFG_GPO(GPP_B4, 1, DEEP), + /* CPU PCIe VGPIO for PEG60 */ + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_48, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_49, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_50, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_51, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_52, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_53, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_54, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_55, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_56, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_57, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_58, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_59, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_60, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_61, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_62, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_63, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_76, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_77, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_78, NONE, DEEP, NF1), + PAD_CFG_NF_VWEN(GPP_vGPIO_PCIE_79, NONE, DEEP, NF1), +}; + +const struct pad_config *variant_gpio_override_table(size_t *num) +{ + *num = ARRAY_SIZE(override_gpio_table); + return override_gpio_table; +} + +const struct pad_config *variant_early_gpio_table(size_t *num) +{ + *num = ARRAY_SIZE(early_gpio_table); + return early_gpio_table; +} diff --git a/src/mainboard/google/brya/variants/taeko4es/include/variant/ec.h b/src/mainboard/google/brya/variants/taeko4es/include/variant/ec.h new file mode 100644 index 0000000..7a2a6ff --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/include/variant/ec.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef __VARIANT_EC_H__ +#define __VARIANT_EC_H__ + +#include <baseboard/ec.h> + +#endif diff --git a/src/mainboard/google/brya/variants/taeko4es/include/variant/gpio.h b/src/mainboard/google/brya/variants/taeko4es/include/variant/gpio.h new file mode 100644 index 0000000..c4fe342 --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/include/variant/gpio.h @@ -0,0 +1,8 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#ifndef VARIANT_GPIO_H +#define VARIANT_GPIO_H + +#include <baseboard/gpio.h> + +#endif diff --git a/src/mainboard/google/brya/variants/taeko4es/memory.c b/src/mainboard/google/brya/variants/taeko4es/memory.c new file mode 100644 index 0000000..9a7ef5c --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/memory.c @@ -0,0 +1,97 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ + +#include <baseboard/gpio.h> +#include <baseboard/variants.h> +#include <gpio.h> + +static const struct mb_cfg baseboard_memcfg = { + .type = MEM_TYPE_LP4X, + + .rcomp = { + /* Baseboard uses only 100ohm Rcomp resistors */ + .resistor = 100, + + /* Baseboard Rcomp target values */ + .targets = {40, 30, 30, 30, 30}, + }, + + /* DQ byte map */ + .lpx_dq_map = { + .ddr0 = { + .dq0 = { 9, 11, 8, 10, 12, 14, 13, 15, }, + .dq1 = { 4, 7, 6, 5, 2, 3, 0, 1, }, + }, + .ddr1 = { + .dq0 = { 15, 12, 14, 13, 9, 10, 11, 8, }, + .dq1 = { 0, 1, 3, 2, 7, 5, 4, 6, }, + }, + .ddr2 = { + .dq0 = { 2, 3, 1, 0, 6, 7, 5, 4, }, + .dq1 = { 15, 9, 14, 8, 11, 10, 13, 12, }, + }, + .ddr3 = { + .dq0 = { 3, 1, 2, 0, 4, 6, 7, 5, }, + .dq1 = { 13, 15, 14, 12, 11, 9, 8, 10, }, + }, + .ddr4 = { + .dq0 = { 13, 12, 14, 15, 9, 8, 10, 11, }, + .dq1 = { 4, 7, 5, 6, 1, 2, 0, 3, }, + }, + .ddr5 = { + .dq0 = { 5, 0, 6, 4, 3, 1, 7, 2, }, + .dq1 = { 11, 9, 10, 8, 15, 12, 14, 13, }, + }, + .ddr6 = { + .dq0 = { 15, 12, 14, 13, 10, 9, 11, 8, }, + .dq1 = { 0, 1, 2, 3, 5, 6, 4, 7, }, + }, + .ddr7 = { + .dq0 = { 0, 3, 1, 2, 4, 5, 6, 7, }, + .dq1 = { 11, 8, 13, 14, 9, 12, 15, 10, }, + }, + }, + + /* DQS CPU<>DRAM map */ + .lpx_dqs_map = { + .ddr0 = { .dqs0 = 0, .dqs1 = 1 }, + .ddr1 = { .dqs0 = 0, .dqs1 = 1 }, + .ddr2 = { .dqs0 = 0, .dqs1 = 1 }, + .ddr3 = { .dqs0 = 0, .dqs1 = 1 }, + .ddr4 = { .dqs0 = 0, .dqs1 = 1 }, + .ddr5 = { .dqs0 = 0, .dqs1 = 1 }, + .ddr6 = { .dqs0 = 0, .dqs1 = 1 }, + .ddr7 = { .dqs0 = 0, .dqs1 = 1 }, + }, + + .ect = 1, /* Enable Early Command Training */ +}; + +const struct mb_cfg *__weak variant_memory_params(void) +{ + return &baseboard_memcfg; +} + +int __weak variant_memory_sku(void) +{ + /* + * Memory configuration board straps + * GPIO_MEM_CONFIG_0 GPP_E11 + * GPIO_MEM_CONFIG_1 GPP_E2 + * GPIO_MEM_CONFIG_2 GPP_E1 + * GPIO_MEM_CONFIG_3 GPP_E12 + */ + gpio_t spd_gpios[] = { + GPP_E11, + GPP_E2, + GPP_E1, + GPP_E12, + }; + + return gpio_base2_value(spd_gpios, ARRAY_SIZE(spd_gpios)); +} + +bool __weak variant_is_half_populated(void) +{ + /* GPIO_MEM_CH_SEL GPP_E13 */ + return gpio_get(GPP_E13); +} diff --git a/src/mainboard/google/brya/variants/taeko4es/memory/Makefile.inc b/src/mainboard/google/brya/variants/taeko4es/memory/Makefile.inc new file mode 100644 index 0000000..2ac3e32 --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/memory/Makefile.inc @@ -0,0 +1,7 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/taeko/memory src/mainboard/google/brya/variants/taeko/memory/mem_parts_used.txt + +SPD_SOURCES = +SPD_SOURCES += spd/lp4x/set-0/spd-1.hex # ID = 0(0b0000) Parts = MT53E512M32D2NP-046 WT:E, K4U6E3S4AA-MGCR, H9HCNNNBKMMLXR-NEE, MT53E512M32D1NP-046 WT:B, K4U6E3S4AB-MGCL, H54G46CYRBX267 diff --git a/src/mainboard/google/brya/variants/taeko4es/memory/dram_id.generated.txt b/src/mainboard/google/brya/variants/taeko4es/memory/dram_id.generated.txt new file mode 100644 index 0000000..fda303c --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/memory/dram_id.generated.txt @@ -0,0 +1,12 @@ +# SPDX-License-Identifier: GPL-2.0-or-later +# This is an auto-generated file. Do not edit!! +# Generated by: +# util/spd_tools/bin/part_id_gen ADL lp4x src/mainboard/google/brya/variants/taeko/memory src/mainboard/google/brya/variants/taeko/memory/mem_parts_used.txt + +DRAM Part Name ID to assign +MT53E512M32D2NP-046 WT:E 0 (0000) +K4U6E3S4AA-MGCR 0 (0000) +H9HCNNNBKMMLXR-NEE 0 (0000) +MT53E512M32D1NP-046 WT:B 0 (0000) +K4U6E3S4AB-MGCL 0 (0000) +H54G46CYRBX267 0 (0000) diff --git a/src/mainboard/google/brya/variants/taeko4es/memory/mem_parts_used.txt b/src/mainboard/google/brya/variants/taeko4es/memory/mem_parts_used.txt new file mode 100644 index 0000000..dd80fc8 --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/memory/mem_parts_used.txt @@ -0,0 +1,6 @@ +MT53E512M32D2NP-046 WT:E +K4U6E3S4AA-MGCR +H9HCNNNBKMMLXR-NEE +MT53E512M32D1NP-046 WT:B +K4U6E3S4AB-MGCL +H54G46CYRBX267 diff --git a/src/mainboard/google/brya/variants/taeko4es/overridetree.cb b/src/mainboard/google/brya/variants/taeko4es/overridetree.cb new file mode 100644 index 0000000..d485662 --- /dev/null +++ b/src/mainboard/google/brya/variants/taeko4es/overridetree.cb @@ -0,0 +1,500 @@ +fw_config + field DB_USB 0 1 + option DB_USB_ABSENT 0 + option DB_USB3_NO_A 1 + end + field DB_SD 2 3 + option DB_SD_ABSENT 0 + option DB_SD_OZ711LV2LN 1 + option DB_SD_GL9750 2 + option DB_SD_RTS5232S 3 + end + field KB_BL 4 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field AUDIO 5 7 + option AUDIO_UNKNOWN 0 + option AUDIO_MAX98357_ALC5682I_I2S 1 + option AUDIO_MAX98357_ALC5682I_VS_I2S 2 + end + field KB_LAYOUT 8 9 + option KB_LAYOUT_DEFAULT 0 + end + field WIFI_SAR_ID 10 11 + option WIFI_SAR_ID_0 0 + option WIFI_SAR_ID_1 1 + option WIFI_SAR_ID_2 2 + option WIFI_SAR_ID_3 3 + end + field BOOT_NVME_MASK 12 + option BOOT_NVME_DISABLED 0 + option BOOT_NVME_ENABLED 1 + end + field BOOT_EMMC_MASK 13 + option BOOT_EMMC_DISABLED 0 + option BOOT_EMMC_ENABLED 1 + end + field HPS 17 + option HPS_ABSENT 0 + option HPS_PRESENT 1 + end +end +chip soc/intel/alderlake + # This disabled autonomous GPIO power management, otherwise + # old cr50 FW only supports short pulses; need to clarify + # the minimum PCH IRQ pulse width with Intel, b/180111628 + register "gpio_override_pm" = "1" + register "gpio_pm[COMM_0]" = "0" + register "gpio_pm[COMM_1]" = "0" + register "gpio_pm[COMM_2]" = "0" + register "gpio_pm[COMM_3]" = "0" + register "gpio_pm[COMM_4]" = "0" + register "gpio_pm[COMM_5]" = "0" + register "ext_fivr_settings" = "{ + .configure_ext_fivr = 1, + .v1p05_enable_bitmap = FIVR_ENABLE_ALL_SX, + .vnn_enable_bitmap = FIVR_ENABLE_ALL_SX, + .v1p05_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL | + FIVR_VOLTAGE_MIN_ACTIVE | + FIVR_VOLTAGE_MIN_RETENTION, + .vnn_supported_voltage_bitmap = FIVR_VOLTAGE_NORMAL | + FIVR_VOLTAGE_MIN_ACTIVE | + FIVR_VOLTAGE_MIN_RETENTION, + .v1p05_icc_max_ma = 500, + .vnn_sx_voltage_mv = 1250, + }" + register "TcssAuxOri" = "1" + register "typec_aux_bias_pads[0]" = "{.pad_auxp_dc = GPP_E22, .pad_auxn_dc = GPP_E23}" + register "SaGv" = "SaGv_Enabled" + + register "usb2_ports[1]" = "USB2_PORT_EMPTY" # Disable Port 1 + register "usb2_ports[2]" = "USB2_PORT_TYPE_C(OC2)" # DB USB2_C1 + register "usb2_ports[3]" = "USB2_PORT_EMPTY" # Disable M.2 WWAN + register "usb3_ports[3]" = "USB3_PORT_EMPTY" # Disable M.2 WWAN + + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI1 | Fingerprint MCU | + #| I2C0 | Audio | + #| I2C1 | Touchscreen | + #| I2C2 | HPS | + #| I2C3 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+ + register "common_soc_config" = "{ + .i2c[0] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[1] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[2] = { + .speed = I2C_SPEED_FAST, + }, + .i2c[3] = { + .early_init = 1, + .speed = I2C_SPEED_FAST, + }, + .i2c[5] = { + .speed = I2C_SPEED_FAST, + }, + }" + # I2C Port Config + register "SerialIoI2cMode" = "{ + [PchSerialIoIndexI2C0] = PchSerialIoPci, + [PchSerialIoIndexI2C1] = PchSerialIoPci, + [PchSerialIoIndexI2C2] = PchSerialIoPci, + [PchSerialIoIndexI2C3] = PchSerialIoPci, + [PchSerialIoIndexI2C4] = PchSerialIoDisabled, + [PchSerialIoIndexI2C5] = PchSerialIoPci, + }" + device domain 0 on + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DRAM_SOC"" + register "options.tsr[1].desc" = ""Ambient"" + register "options.tsr[2].desc" = ""Charger"" + register "options.tsr[3].desc" = ""WWAN"" + + # TODO: below values are initial reference values only + ## Active Policy + register "policies.active" = "{ + [0] = { + .target = DPTF_CPU, + .thresholds = { + TEMP_PCT(85, 90), + TEMP_PCT(80, 74), + TEMP_PCT(75, 74), + TEMP_PCT(70, 74), + TEMP_PCT(65, 74), + } + }, + [1] = { + .target = DPTF_TEMP_SENSOR_1, + .thresholds = { + TEMP_PCT(51, 74), + TEMP_PCT(47, 60), + TEMP_PCT(45, 45), + TEMP_PCT(42, 45), + TEMP_PCT(37, 35), + } + }, + [2] = { + .target = DPTF_TEMP_SENSOR_2, + .thresholds = { + TEMP_PCT(51, 74), + TEMP_PCT(47, 60), + TEMP_PCT(45, 45), + TEMP_PCT(42, 45), + TEMP_PCT(37, 35), + } + }, + [3] = { + .target = DPTF_TEMP_SENSOR_3, + .thresholds = { + TEMP_PCT(51, 74), + TEMP_PCT(47, 60), + TEMP_PCT(45, 45), + TEMP_PCT(42, 45), + TEMP_PCT(37, 35), + } + } + }" + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 90, 6000), + [2] = DPTF_PASSIVE(CPU, TEMP_SENSOR_1, 90, 6000), + [3] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_2, 90, 6000), + [4] = DPTF_PASSIVE(CPU, TEMP_SENSOR_3, 90, 6000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 100, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 100, SHUTDOWN), + [3] = DPTF_CRITICAL(TEMP_SENSOR_2, 100, SHUTDOWN), + [4] = DPTF_CRITICAL(TEMP_SENSOR_3, 100, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 3000, + .max_power = 12000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200, + }, + .pl2 = { + .min_power = 55000, + .max_power = 55000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + ## Fan Performance Control (Percent, Speed, Noise, Power) + register "controls.fan_perf" = "{ + [0] = { 100, 6000, 220, 2200, }, + [1] = { 92, 5500, 180, 1800, }, + [2] = { 85, 5000, 145, 1450, }, + [3] = { 74, 4620, 115, 1150, }, + [4] = { 60, 4290, 90, 900, }, + [5] = { 45, 3980, 55, 550, }, + [6] = { 35, 3170, 30, 300, }, + [7] = { 30, 2640, 15, 150, }, + [8] = { 10, 800, 10, 100, }, + [9] = { 0, 0, 0, 50, } + }" + + ## Fan options + register "options.fan.fine_grained_control" = "1" + register "options.fan.step_size" = "2" + + device generic 0 alias dptf_policy on end + end + end + device ref pcie4_0 on + # Enable CPU PCIE RP 1 using CLK 0 + register "cpu_pcie_rp[CPU_RP(1)]" = "{ + .clk_req = 0, + .clk_src = 0, + }" + end + device ref tbt_pcie_rp0 off end + device ref tbt_pcie_rp1 off end + device ref tbt_pcie_rp2 off end + device ref i2c0 on + chip drivers/i2c/generic + register "hid" = ""10EC5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO AUDIO_MAX98357_ALC5682I_I2S + end + end + chip drivers/i2c/generic + register "hid" = ""RTL5682"" + register "name" = ""RT58"" + register "desc" = ""Headset Codec"" + register "irq_gpio" = "ACPI_GPIO_IRQ_EDGE_BOTH(GPP_A23)" + # Set the jd_src to RT5668_JD1 for jack detection + register "property_count" = "1" + register "property_list[0].type" = "ACPI_DP_TYPE_INTEGER" + register "property_list[0].name" = ""realtek,jd-src"" + register "property_list[0].integer" = "1" + device i2c 1a on + probe AUDIO AUDIO_MAX98357_ALC5682I_VS_I2S + end + end + end + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""GDIX0000"" + register "generic.desc" = ""Goodix Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + # Parameter T5 >= 180ms + register "generic.reset_delay_ms" = "180" + # Parameter T2 >= 1ms + register "generic.reset_off_delay_ms" = "3" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + # Parameter T1 >= 20ms + register "generic.enable_delay_ms" = "20" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_E3)" + # Parameter T4 >= 1ms + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 5d on end + end + chip drivers/i2c/generic + register "hid" = ""ELAN0001"" + register "desc" = ""ELAN Touchscreen"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "probed" = "1" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "reset_delay_ms" = "20" + register "enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "enable_delay_ms" = "1" + register "has_power_resource" = "1" + device i2c 10 on end + end + end + device ref i2c2 on + chip drivers/i2c/generic + register "hid" = ""GOOG0020"" + register "desc" = ""Chrome OS HPS"" + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E7)" # EN_HPS_PWR + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_E3_IRQ)" # HPS_INT_ODL + # HPS uses I2C addresses 0x30 and 0x51. + # The address we provide here is not significant because + # neither coreboot nor Linux have a driver for HPS, + # it's only used from userspace. + device i2c 30 on + probe HPS HPS_PRESENT + end + end + end + device ref i2c3 on + chip drivers/i2c/tpm + register "hid" = ""GOOG0005"" + register "irq" = "ACPI_IRQ_EDGE_LOW(GPP_A13_IRQ)" + device i2c 50 on end + end + end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on end + end + chip drivers/i2c/hid + register "generic.hid" = ""PNP0C50"" + register "generic.desc" = ""Synaptics Touchpad"" + register "generic.irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "generic.wake" = "GPE0_DW2_14" + register "generic.probed" = "1" + register "hid_desc_reg_offset" = "0x20" + device i2c 2c on end + end + end + device ref hda on + chip drivers/generic/max98357a + register "hid" = ""MX98357A"" + register "sdmode_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_A11)" + register "sdmode_delay" = "5" + device generic 0 on + probe AUDIO AUDIO_MAX98357_ALC5682I_I2S + probe AUDIO AUDIO_MAX98357_ALC5682I_VS_I2S + end + end + end + device ref pcie_rp5 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_B11)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_H20)" + register "srcclk_pin" = "2" + device generic 0 on end + end + register "pch_pcie_rp[PCH_RP(5)]" = "{ + .clk_src = 2, + .clk_req = 2, + .flags = PCIE_RP_LTR | PCIE_RP_AER, + }" + end + device ref pcie_rp6 off end + device ref pcie_rp8 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_H13)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D18)" + register "srcclk_pin" = "3" + device generic 0 on + probe DB_SD DB_SD_OZ711LV2LN + probe DB_SD DB_SD_GL9750 + probe DB_SD DB_SD_RTS5232S + end + end + end + device ref pcie_rp9 on + chip soc/intel/common/block/pcie/rtd3 + register "enable_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_D11)" + register "reset_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_B4)" + register "srcclk_pin" = "1" + device generic 0 on end + end + end + device ref gspi1 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" + register "wake" = "GPE0_DW2_15" + device spi 0 on end + end # FPMCU + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "1" + register "usb3_port_number" = "1" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "3" + register "usb3_port_number" = "3" + device generic 2 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref tcss_usb3_port3 on + probe DB_USB DB_USB3_NO_A + end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (DB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on + probe DB_USB DB_USB3_NO_A + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on + end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb2_port9 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(4, 1)" + device ref usb3_port1 on end + end + end + end + end + end +end