David Wu has uploaded this change for review. ( https://review.coreboot.org/c/coreboot/+/57017 )
Change subject: mb/google/brya/variants/kano: Init devicetree for kano ......................................................................
mb/google/brya/variants/kano: Init devicetree for kano
Init basic override devicetree based on schematics
BUG=b:192370253 TEST=FW_NAME=kano emerge-brya coreboot chromeos-bootimage
Signed-off-by: David Wu david_wu@quanta.corp-partner.google.com Change-Id: I283517427612e24eabe2ce736d677253065c7859 --- M src/mainboard/google/brya/Kconfig.name M src/mainboard/google/brya/variants/kano/Makefile.inc A src/mainboard/google/brya/variants/kano/fw_config.c M src/mainboard/google/brya/variants/kano/overridetree.cb 4 files changed, 471 insertions(+), 1 deletion(-)
git pull ssh://review.coreboot.org:29418/coreboot refs/changes/17/57017/1
diff --git a/src/mainboard/google/brya/Kconfig.name b/src/mainboard/google/brya/Kconfig.name index a985d8d..e395c1a 100644 --- a/src/mainboard/google/brya/Kconfig.name +++ b/src/mainboard/google/brya/Kconfig.name @@ -33,6 +33,8 @@ config BOARD_GOOGLE_KANO bool "-> Kano" select BOARD_GOOGLE_BASEBOARD_BRYA + select DRIVERS_I2C_MAX98373 + select DRIVERS_I2C_NAU8825
config BOARD_GOOGLE_TAEKO bool "-> Taeko" diff --git a/src/mainboard/google/brya/variants/kano/Makefile.inc b/src/mainboard/google/brya/variants/kano/Makefile.inc index 8fe978f..f2a624c 100644 --- a/src/mainboard/google/brya/variants/kano/Makefile.inc +++ b/src/mainboard/google/brya/variants/kano/Makefile.inc @@ -2,3 +2,5 @@ bootblock-y += gpio.c
ramstage-y += gpio.c + +ramstage-$(CONFIG_FW_CONFIG) += fw_config.c diff --git a/src/mainboard/google/brya/variants/kano/fw_config.c b/src/mainboard/google/brya/variants/kano/fw_config.c new file mode 100644 index 0000000..ade89da --- /dev/null +++ b/src/mainboard/google/brya/variants/kano/fw_config.c @@ -0,0 +1,59 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#include <bootstate.h> +#include <console/console.h> +#include <fw_config.h> +#include <gpio.h> + +static const struct pad_config dmic_enable_pads[] = { + PAD_CFG_NF(GPP_S2, NONE, DEEP, NF2), /* DMIC_CLK0_R */ + PAD_CFG_NF(GPP_S3, NONE, DEEP, NF2), /* DMIC_DATA0_R */ + PAD_CFG_NF(GPP_S6, NONE, DEEP, NF2), /* DMIC_CLK1_R */ + PAD_CFG_NF(GPP_S7, NONE, DEEP, NF2), /* DMIC_DATA1_R */ +}; + +static const struct pad_config dmic_disable_pads[] = { + PAD_NC(GPP_S2, NONE), + PAD_NC(GPP_S3, NONE), + PAD_NC(GPP_S6, NONE), + PAD_NC(GPP_S7, NONE), +}; + +static const struct pad_config i2s_enable_pads[] = { + PAD_CFG_NF(GPP_R0, NONE, DEEP, NF2), /* I2S_HP_SCLK_R */ + PAD_CFG_NF(GPP_R1, NONE, DEEP, NF2), /* I2S_HP_SFRM_R */ + PAD_CFG_NF(GPP_R2, DN_20K, DEEP, NF2), /* I2S_PCH_TX_HP_RX_STRAP */ + PAD_CFG_NF(GPP_R3, NONE, DEEP, NF2), /* I2S_PCH_RX_HP_TX */ + PAD_CFG_NF(GPP_R4, NONE, DEEP, NF2), /* I2S_SPKR_SCLK_R */ + PAD_CFG_NF(GPP_R5, NONE, DEEP, NF2), /* I2S_SPKR_SFRM_R */ + PAD_CFG_NF(GPP_R6, NONE, DEEP, NF2), /* I2S_PCH_TX_SPKR_RX_R */ + PAD_CFG_NF(GPP_R7, NONE, DEEP, NF2), /* I2S_PCH_RX_SPKR_TX */ +}; + +static const struct pad_config i2s_disable_pads[] = { + PAD_NC(GPP_R0, NONE), + PAD_NC(GPP_R1, NONE), + PAD_NC(GPP_R2, NONE), + PAD_NC(GPP_R3, NONE), + PAD_NC(GPP_R4, NONE), + PAD_NC(GPP_R5, NONE), + PAD_NC(GPP_R6, NONE), + PAD_NC(GPP_R7, NONE), +}; + +static void fw_config_handle(void *unused) +{ + if (!fw_config_is_provisioned() || fw_config_probe(FW_CONFIG(AUDIO, AUDIO_UNKNOWN))) { + printk(BIOS_INFO, "Disable audio related GPIO pins.\n"); + gpio_configure_pads(i2s_disable_pads, ARRAY_SIZE(i2s_disable_pads)); + gpio_configure_pads(dmic_disable_pads, ARRAY_SIZE(dmic_disable_pads)); + return; + } + + if (fw_config_probe(FW_CONFIG(AUDIO, MAX98373_NAU88L25B_I2S))) { + printk(BIOS_INFO, "Configure audio over I2S with MAX98373 NAU88L25B.\n"); + gpio_configure_pads(dmic_enable_pads, ARRAY_SIZE(dmic_enable_pads)); + gpio_configure_pads(i2s_enable_pads, ARRAY_SIZE(i2s_enable_pads)); + } +} +BOOT_STATE_INIT_ENTRY(BS_DEV_ENABLE, BS_ON_ENTRY, fw_config_handle, NULL); diff --git a/src/mainboard/google/brya/variants/kano/overridetree.cb b/src/mainboard/google/brya/variants/kano/overridetree.cb index 4f2c04a..448ff79 100644 --- a/src/mainboard/google/brya/variants/kano/overridetree.cb +++ b/src/mainboard/google/brya/variants/kano/overridetree.cb @@ -1,6 +1,413 @@ +fw_config + field DB_USB 0 3 + option USB_ABSENT 0 + end + field DB_SD 4 5 + option SD_ABSENT 0 + end + field KB_BL 7 7 + option KB_BL_ABSENT 0 + option KB_BL_PRESENT 1 + end + field AUDIO 8 10 + option AUDIO_UNKNOWN 0 + option MAX98373_NAU88L25B_I2S 1 + end +end chip soc/intel/alderlake + # Intel Common SoC Config + #+-------------------+---------------------------+ + #| Field | Value | + #+-------------------+---------------------------+ + #| GSPI1 | Fingerprint MCU | + #| I2C0 | Audio | + #| I2C1 | Touchscreen | + #| I2C2 | SAR0 | + #| I2C3 | cr50 TPM. Early init is | + #| | required to set up a BAR | + #| | for TPM communication | + #| I2C5 | Trackpad | + #+-------------------+---------------------------+
device domain 0 on - end + device ref dtt on + chip drivers/intel/dptf + ## sensor information + register "options.tsr[0].desc" = ""DRAM"" + register "options.tsr[1].desc" = ""Charger""
+ # TODO: below values are initial reference values only + ## Active Policy + register "policies.active" = "{ + [0] = { + .target = DPTF_CPU, + .thresholds = { + TEMP_PCT(85, 90), + TEMP_PCT(80, 80), + TEMP_PCT(75, 70), + } + } + }" + + ## Passive Policy + register "policies.passive" = "{ + [0] = DPTF_PASSIVE(CPU, CPU, 95, 5000), + [1] = DPTF_PASSIVE(CPU, TEMP_SENSOR_0, 75, 5000), + [2] = DPTF_PASSIVE(CHARGER, TEMP_SENSOR_1, 75, 5000), + }" + + ## Critical Policy + register "policies.critical" = "{ + [0] = DPTF_CRITICAL(CPU, 105, SHUTDOWN), + [1] = DPTF_CRITICAL(TEMP_SENSOR_0, 85, SHUTDOWN), + [2] = DPTF_CRITICAL(TEMP_SENSOR_1, 85, SHUTDOWN), + }" + + register "controls.power_limits" = "{ + .pl1 = { + .min_power = 3000, + .max_power = 15000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 200, + }, + .pl2 = { + .min_power = 55000, + .max_power = 55000, + .time_window_min = 28 * MSECS_PER_SEC, + .time_window_max = 32 * MSECS_PER_SEC, + .granularity = 1000, + } + }" + + ## Charger Performance Control (Control, mA) + register "controls.charger_perf" = "{ + [0] = { 255, 1700 }, + [1] = { 24, 1500 }, + [2] = { 16, 1000 }, + [3] = { 8, 500 } + }" + + ## Fan Performance Control (Percent, Speed, Noise, Power) + register "controls.fan_perf" = "{ + [0] = { 90, 6700, 220, 2200, }, + [1] = { 80, 5800, 180, 1800, }, + [2] = { 70, 5000, 145, 1450, }, + [3] = { 60, 4900, 115, 1150, }, + [4] = { 50, 3838, 90, 900, }, + [5] = { 40, 2904, 55, 550, }, + [6] = { 30, 2337, 30, 300, }, + [7] = { 20, 1608, 15, 150, }, + [8] = { 10, 800, 10, 100, }, + [9] = { 0, 0, 0, 50, } + }" + + ## Fan options + register "options.fan.fine_grained_control" = "1" + register "options.fan.step_size" = "2" + + device generic 0 on end + end + end + device ref ipu on end + device ref pcie4_0 on + # Enable CPU PCIE RP 1 using CLK 0 + register "cpu_pcie_rp[CPU_RP(1)]" = "{ + .clk_req = 0, + .clk_src = 0, + }" + end + device ref tcss_dma0 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port1 as dfp[0].typec_port + device generic 0 on end + end + end + device ref tcss_dma1 on + chip drivers/intel/usb4/retimer + register "dfp[0].power_gpio" = "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_E4)" + use tcss_usb3_port3 as dfp[0].typec_port + device generic 0 on end + end + end + device ref cnvi_wifi on + chip drivers/wifi/generic + register "wake" = "GPE0_PME_B0" + device generic 0 on end + end + end + device ref i2c0 on + chip drivers/i2c/nau8825 + register "irq_gpio" = "ACPI_GPIO_IRQ_LEVEL_LOW(GPP_A23)" + register "jkdet_enable" = "1" + register "jkdet_pull_enable" = "0" + register "jkdet_pull_up" = "0" + register "jkdet_polarity" = "1" # ActiveLow + register "vref_impedance" = "2" # 125kOhm + register "micbias_voltage" = "6" # 2.754 + register "sar_threshold_num" = "4" + register "sar_threshold[0]" = "0x0C" + register "sar_threshold[1]" = "0x1C" + register "sar_threshold[2]" = "0x38" + register "sar_threshold[3]" = "0x60" + register "sar_hysteresis" = "1" + register "sar_voltage" = "6" + register "sar_compare_time" = "0" # 500ns + register "sar_sampling_time" = "0" # 2us + register "short_key_debounce" = "2" # 100ms + register "jack_insert_debounce" = "7" # 512ms + register "jack_eject_debounce" = "7" # 512ms + device i2c 1a on + probe AUDIO MAX98373_NAU88L25B_I2S + end + end + end #I2C0 + device ref i2c1 on + chip drivers/i2c/hid + register "generic.hid" = ""ELAN90FC"" + register "generic.desc" = ""ELAN Touchscreen"" + register "generic.irq" = "ACPI_IRQ_LEVEL_LOW(GPP_C7_IRQ)" + register "generic.probed" = "1" + register "generic.reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C1)" + register "generic.reset_delay_ms" = "300" + register "generic.reset_off_delay_ms" = "1" + register "generic.enable_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_HIGH(GPP_C0)" + register "generic.enable_delay_ms" = "6" + register "generic.stop_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_C6)" + register "generic.stop_off_delay_ms" = "1" + register "generic.has_power_resource" = "1" + register "hid_desc_reg_offset" = "0x01" + device i2c 0x10 on end + end + end + device ref i2c2 on + chip drivers/i2c/sx9324 + register "desc" = ""SAR1 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_B3_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "1" + register "reg_gnrl_ctrl0" = "0x16" + register "reg_gnrl_ctrl1" = "0x21" + register "reg_afe_ctrl0" = "0x00" + register "reg_afe_ctrl1" = "0x10" + register "reg_afe_ctrl2" = "0x00" + register "reg_afe_ctrl3" = "0x00" + register "reg_afe_ctrl4" = "0x07" + register "reg_afe_ctrl5" = "0x00" + register "reg_afe_ctrl6" = "0x00" + register "reg_afe_ctrl7" = "0x07" + register "reg_afe_ctrl8" = "0x12" + register "reg_afe_ctrl9" = "0x0f" + register "reg_prox_ctrl0" = "0x12" + register "reg_prox_ctrl1" = "0x12" + register "reg_prox_ctrl2" = "0x90" + register "reg_prox_ctrl3" = "0x60" + register "reg_prox_ctrl4" = "0x0c" + register "reg_prox_ctrl5" = "0x12" + register "reg_prox_ctrl6" = "0x3c" + register "reg_prox_ctrl7" = "0x58" + register "reg_adv_ctrl0" = "0x00" + register "reg_adv_ctrl1" = "0x00" + register "reg_adv_ctrl2" = "0x00" + register "reg_adv_ctrl3" = "0x00" + register "reg_adv_ctrl4" = "0x00" + register "reg_adv_ctrl5" = "0x05" + register "reg_adv_ctrl6" = "0x00" + register "reg_adv_ctrl7" = "0x00" + register "reg_adv_ctrl8" = "0x00" + register "reg_adv_ctrl9" = "0x00" + register "reg_adv_ctrl10" = "0x5c" + register "reg_adv_ctrl11" = "0x52" + register "reg_adv_ctrl12" = "0xb5" + register "reg_adv_ctrl13" = "0x00" + register "reg_adv_ctrl14" = "0x80" + register "reg_adv_ctrl15" = "0x0c" + register "reg_adv_ctrl16" = "0x38" + register "reg_adv_ctrl17" = "0x56" + register "reg_adv_ctrl18" = "0x33" + register "reg_adv_ctrl19" = "0xf0" + register "reg_adv_ctrl20" = "0xf0" + device i2c 28 on end + end + chip drivers/i2c/sx9324 + register "desc" = ""SAR2 Proximity Sensor"" + register "irq" = "ACPI_IRQ_LEVEL_LOW(GPP_H19_IRQ)" + register "speed" = "I2C_SPEED_FAST" + register "uid" = "2" + register "reg_gnrl_ctrl0" = "0x16" + register "reg_gnrl_ctrl1" = "0x21" + register "reg_afe_ctrl0" = "0x00" + register "reg_afe_ctrl1" = "0x10" + register "reg_afe_ctrl2" = "0x00" + register "reg_afe_ctrl3" = "0x00" + register "reg_afe_ctrl4" = "0x07" + register "reg_afe_ctrl5" = "0x00" + register "reg_afe_ctrl6" = "0x00" + register "reg_afe_ctrl7" = "0x07" + register "reg_afe_ctrl8" = "0x12" + register "reg_afe_ctrl9" = "0x0f" + register "reg_prox_ctrl0" = "0x12" + register "reg_prox_ctrl1" = "0x12" + register "reg_prox_ctrl2" = "0x90" + register "reg_prox_ctrl3" = "0x60" + register "reg_prox_ctrl4" = "0x0c" + register "reg_prox_ctrl5" = "0x12" + register "reg_prox_ctrl6" = "0x3c" + register "reg_prox_ctrl7" = "0x58" + register "reg_adv_ctrl0" = "0x00" + register "reg_adv_ctrl1" = "0x00" + register "reg_adv_ctrl2" = "0x00" + register "reg_adv_ctrl3" = "0x00" + register "reg_adv_ctrl4" = "0x00" + register "reg_adv_ctrl5" = "0x05" + register "reg_adv_ctrl6" = "0x00" + register "reg_adv_ctrl7" = "0x00" + register "reg_adv_ctrl8" = "0x00" + register "reg_adv_ctrl9" = "0x00" + register "reg_adv_ctrl10" = "0x5c" + register "reg_adv_ctrl11" = "0x52" + register "reg_adv_ctrl12" = "0xb5" + register "reg_adv_ctrl13" = "0x00" + register "reg_adv_ctrl14" = "0x80" + register "reg_adv_ctrl15" = "0x0c" + register "reg_adv_ctrl16" = "0x38" + register "reg_adv_ctrl17" = "0x56" + register "reg_adv_ctrl18" = "0x33" + register "reg_adv_ctrl19" = "0xf0" + register "reg_adv_ctrl20" = "0xf0" + device i2c 2C on end + end + end + device ref i2c3 on end + device ref i2c5 on + chip drivers/i2c/generic + register "hid" = ""ELAN0000"" + register "desc" = ""ELAN Touchpad"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F14_IRQ)" + register "wake" = "GPE0_DW2_14" + register "probed" = "1" + device i2c 15 on end + end + end + device ref hda on + chip drivers/i2c/max98373 + register "vmon_slot_no" = "0" + register "imon_slot_no" = "1" + register "uid" = "0" + register "desc" = ""Right Speaker Amp"" + register "name" = ""MAXR"" + device i2c 31 on + probe AUDIO MAX98373_NAU88L25B_I2S + end + end + chip drivers/i2c/max98373 + register "vmon_slot_no" = "2" + register "imon_slot_no" = "3" + register "uid" = "1" + register "desc" = ""Left Speaker Amp"" + register "name" = ""MAXL"" + device i2c 32 on + probe AUDIO MAX98373_NAU88L25B_I2S + end + end + end + device ref gspi1 on + chip drivers/spi/acpi + register "name" = ""CRFP"" + register "hid" = "ACPI_DT_NAMESPACE_HID" + register "uid" = "1" + register "compat_string" = ""google,cros-ec-spi"" + register "irq" = "ACPI_IRQ_WAKE_LEVEL_LOW(GPP_F15_IRQ)" + register "wake" = "GPE0_DW2_15" + device spi 0 on end + end # FPMCU + end + device ref pch_espi on + chip ec/google/chromeec + use conn0 as mux_conn[0] + use conn1 as mux_conn[1] + device pnp 0c09.0 on end + end + end + device ref pmc hidden + chip drivers/intel/pmc_mux + device generic 0 on + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "1" + register "usb3_port_number" = "1" + device generic 0 alias conn0 on end + end + chip drivers/intel/pmc_mux/conn + register "usb2_port_number" = "3" + register "usb3_port_number" = "3" + device generic 1 alias conn1 on end + end + end + end + end + device ref tcss_xhci on + chip drivers/usb/acpi + device ref tcss_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref tcss_usb3_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-C Port C1 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref tcss_usb3_port3 on end + end + end + end + end + device ref xhci on + chip drivers/usb/acpi + device ref xhci_root_hub on + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C0 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(1, 1)" + device ref usb2_port1 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-C Port C1 (MLB)"" + register "type" = "UPC_TYPE_C_USB2_SS_SWITCH" + register "group" = "ACPI_PLD_GROUP(3, 1)" + device ref usb2_port3 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Camera"" + register "type" = "UPC_TYPE_INTERNAL" + device ref usb2_port6 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb2_port9 on end + end + chip drivers/usb/acpi + register "desc" = ""USB2 Bluetooth"" + register "type" = "UPC_TYPE_INTERNAL" + register "reset_gpio" = + "ACPI_GPIO_OUTPUT_ACTIVE_LOW(GPP_D4)" + device ref usb2_port10 on end + end + chip drivers/usb/acpi + register "desc" = ""USB3 Type-A Port A0 (MLB)"" + register "type" = "UPC_TYPE_USB3_A" + register "group" = "ACPI_PLD_GROUP(1, 2)" + device ref usb3_port1 on end + end + end + end + end + end end