August 2021 - flashrom-gerrit - mail.coreboot.org

Change in flashrom[master]: spi25: Add 'spi_read_status_register_2()' helper
by Edward O'Callaghan (Code Review) 06 Dec '21

06 Dec '21

Edward O'Callaghan has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/45748 ) Change subject: spi25: Add 'spi_read_status_register_2()' helper ...................................................................... spi25: Add 'spi_read_status_register_2()' helper Winbond chips have a WRSR opcode of 0x35 interestingly. Add helper to allow for reading it. This is later used by writeprotection support. BUG=b:153800563 BRANCH=none TEST=builds Change-Id: I2d25f22ced17ab94d122e86b270357723b45458e Signed-off-by: Edward O'Callaghan <quasisec(a)google.com> --- M chipdrivers.h M spi25_statusreg.c 2 files changed, 13 insertions(+), 2 deletions(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/48/45748/1 diff --git a/chipdrivers.h b/chipdrivers.h index cf03811..4e76588 100644 --- a/chipdrivers.h +++ b/chipdrivers.h @@ -63,6 +63,7 @@ /* spi25_statusreg.c */ uint8_t spi_read_status_register(const struct flashctx *flash); +uint8_t spi_read_status_register_2(const struct flashctx *flash); int spi_write_status_register(const struct flashctx *flash, int status); void spi_prettyprint_status_register_bit(uint8_t status, int bit); int spi_prettyprint_status_register_plain(struct flashctx *flash); diff --git a/spi25_statusreg.c b/spi25_statusreg.c index 34f9ad4..cad92e6 100644 --- a/spi25_statusreg.c +++ b/spi25_statusreg.c @@ -90,9 +90,9 @@ return ret; } -uint8_t spi_read_status_register(const struct flashctx *flash) +static uint8_t spi_read_status_register_generic(const struct flashctx *flash, uint8_t opcode) { - static const unsigned char cmd[JEDEC_RDSR_OUTSIZE] = { JEDEC_RDSR }; + const unsigned char cmd[JEDEC_RDSR_OUTSIZE] = { opcode }; /* FIXME: No workarounds for driver/hardware bugs in generic code. */ unsigned char readarr[2]; /* JEDEC_RDSR_INSIZE=1 but wbsio needs 2 */ int ret; @@ -108,6 +108,16 @@ return readarr[0]; } +uint8_t spi_read_status_register(const struct flashctx *flash) +{ + return spi_read_status_register_generic(flash, JEDEC_RDSR); +} + +uint8_t spi_read_status_register_2(const struct flashctx *flash) +{ + return spi_read_status_register_generic(flash, 0x35); /* Unclear if this is a std JEDEC opcode. */ +} + /* A generic block protection disable. * Tests if a protection is enabled with the block protection mask (bp_mask) and returns success otherwise. * Tests if the register bits are locked with the lock_mask (lock_mask). -- To view, visit https://review.coreboot.org/c/flashrom/+/45748 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I2d25f22ced17ab94d122e86b270357723b45458e Gerrit-Change-Number: 45748 Gerrit-PatchSet: 1 Gerrit-Owner: Edward O'Callaghan <quasisec(a)chromium.org> Gerrit-MessageType: newchange

3 5

Change in flashrom[master]: Add MEC1308 EC programmer
by Victor Ding (Code Review) 04 Nov '21

04 Nov '21

Victor Ding has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/44541 ) Change subject: Add MEC1308 EC programmer ...................................................................... Add MEC1308 EC programmer Initial support of Microchip MEC1308 Embedded Controller. Signed-off-by: Victor Ding <victording(a)google.com> Change-Id: I2d51b4bdc0b38b6e488e71b9e774eb6232a2069e --- M Makefile M flashrom.c A mec1308.c M meson.build M meson_options.txt M programmer.h 6 files changed, 569 insertions(+), 0 deletions(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/41/44541/1 diff --git a/Makefile b/Makefile index 803529f..2acd656 100644 --- a/Makefile +++ b/Makefile @@ -175,6 +175,11 @@ else override CONFIG_FT2232_SPI = no endif +ifeq ($(CONFIG_MEC1308), yes) +UNSUPPORTED_FEATURES += CONFIG_MEC1308=yes +else +override CONFIG_MEC1308 = no +endif ifeq ($(CONFIG_USBBLASTER_SPI), yes) UNSUPPORTED_FEATURES += CONFIG_USBBLASTER_SPI=yes else @@ -281,6 +286,11 @@ else override CONFIG_DRKAISER = no endif +ifeq ($(CONFIG_MEC1308), yes) +UNSUPPORTED_FEATURES += CONFIG_MEC1308=yes +else +override CONFIG_MEC1308 = no +endif ifeq ($(CONFIG_NICREALTEK), yes) UNSUPPORTED_FEATURES += CONFIG_NICREALTEK=yes else @@ -386,6 +396,11 @@ else override CONFIG_FT2232_SPI = no endif +ifeq ($(CONFIG_MEC1308), yes) +UNSUPPORTED_FEATURES += CONFIG_MEC1308=yes +else +override CONFIG_MEC1308 = no +endif ifeq ($(CONFIG_USBBLASTER_SPI), yes) UNSUPPORTED_FEATURES += CONFIG_USBBLASTER_SPI=yes else @@ -674,6 +689,9 @@ # Always enable FT2232 SPI dongles for now. CONFIG_FT2232_SPI ?= yes +# Microchip MEC1308 Embedded Controller +CONFIG_MEC1308 ?= yes + # Always enable Altera USB-Blaster dongles for now. CONFIG_USBBLASTER_SPI ?= yes @@ -855,6 +873,11 @@ NEED_LIBPCI += CONFIG_INTERNAL endif +ifeq ($(CONFIG_MEC1308), yes) +FEATURE_CFLAGS += -D'CONFIG_MEC1308=1' +PROGRAMMER_OBJS += mec1308.o +endif + ifeq ($(CONFIG_SERPROG), yes) FEATURE_CFLAGS += -D'CONFIG_SERPROG=1' PROGRAMMER_OBJS += serprog.o diff --git a/flashrom.c b/flashrom.c index 4a30986..5a8e37a 100644 --- a/flashrom.c +++ b/flashrom.c @@ -84,6 +84,18 @@ }, #endif +#if CONFIG_MEC1308 == 1 + { + .name = "mec1308", + .type = OTHER, + .devs.note = "Microchip MEC1308 Embedded Controller.\n", + .init = mec1308_init, + .map_flash_region = fallback_map, + .unmap_flash_region = fallback_unmap, + .delay = internal_delay, + }, +#endif + #if CONFIG_NIC3COM == 1 { .name = "nic3com", diff --git a/mec1308.c b/mec1308.c new file mode 100644 index 0000000..43bd2db --- /dev/null +++ b/mec1308.c @@ -0,0 +1,520 @@ +/* + * This file is part of the flashrom project. + * + * Copyright (C) 2010 Google Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * + * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * + * Neither the name of Google or the names of contributors or + * licensors may be used to endorse or promote products derived from this + * software without specific prior written permission. + * + * This software is provided "AS IS," without a warranty of any kind. + * ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, + * INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A + * PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE HEREBY EXCLUDED. + * GOOGLE INC AND ITS LICENSORS SHALL NOT BE LIABLE + * FOR ANY DAMAGES SUFFERED BY LICENSEE AS A RESULT OF USING, MODIFYING + * OR DISTRIBUTING THIS SOFTWARE OR ITS DERIVATIVES. IN NO EVENT WILL + * GOOGLE OR ITS LICENSORS BE LIABLE FOR ANY LOST REVENUE, PROFIT OR DATA, + * OR FOR DIRECT, INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL OR + * PUNITIVE DAMAGES, HOWEVER CAUSED AND REGARDLESS OF THE THEORY OF + * LIABILITY, ARISING OUT OF THE USE OF OR INABILITY TO USE THIS SOFTWARE, + * EVEN IF GOOGLE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. + */ + +#if defined(__i386__) || defined(__x86_64__) +#include <inttypes.h> +#include <stdlib.h> +#include <string.h> +#include <unistd.h> + +#include "flash.h" +#include "hwaccess.h" +#include "chipdrivers.h" +#include "programmer.h" +#include "spi.h" + +#define MEC1308_SIO_PORT1 0x2e +#define MEC1308_SIO_PORT2 0x4e +#define MEC1308_SIO_ENTRY_KEY 0x55 +#define MEC1308_SIO_EXIT_KEY 0xaa + +#define MEC1308_SIOCFG_LDN 0x07 /* LDN Bank Selector */ +#define MEC1308_DEVICE_ID_REG 0x20 /* Device ID Register */ +#define MEC1308_DEVICE_ID_VAL 0x4d /* Device ID Value for MEC1308 */ +#define MEC1310_DEVICE_ID_VAL 0x04 /* Device ID Value for MEC1310 */ +#define MEC1308_DEVICE_REV 0x21 /* Device Revision ID Register */ + +#define MEC1308_MBX_CMD 0x82 /* mailbox command register offset */ +#define MEC1308_MBX_EXT_CMD 0x83 /* mailbox ext. command reg offset */ +#define MEC1308_MBX_DATA_START 0x84 /* first mailbox data register offset */ +#define MEC1308_MBX_DATA_END 0x91 /* last mailbox data register offset */ + +static unsigned int mbx_data; /* Mailbox register interface data address*/ + +/* + * These command codes depend on EC firmware. The ones listed below are input + * using the mailbox interface, though others may be input using the ACPI + * interface. Some commands also have an output value (ie pass/failure code) + * which EC writes to the mailbox command register after completion. + */ +#define MEC1308_CMD_SMI_ENABLE 0x84 +#define MEC1308_CMD_SMI_DISABLE 0x85 +#define MEC1308_CMD_ACPI_ENABLE 0x86 +#define MEC1308_CMD_ACPI_DISABLE 0x87 + +/* + * Passthru commands are also input using the mailbox interface. Passthru mode + * enter/start/end commands are special since they require a command word to + * be written to the data registers. Other passthru commands are performed + * after passthru mode has been started. + * + * Multiple passthru mode commands may be issued before ending passthru mode. + * You do not need to enter, start, and end passthru mode for each SPI + * command. However, other mailbox commands might not work when passthru mode + * is enabled. For example, you may read all SPI chip content while in passthru + * mode, but you should exit passthru mode before performing other EC commands + * such as reading fan speed. + */ +#define MEC1308_CMD_PASSTHRU 0x55 /* force EC to process word */ +#define MEC1308_CMD_PASSTHRU_SUCCESS 0xaa /* success code for passthru */ +#define MEC1308_CMD_PASSTHRU_FAIL 0xfe /* failure code for passthru */ +#define MEC1308_CMD_PASSTHRU_ENTER "PathThruMode" /* not a typo... */ +#define MEC1308_CMD_PASSTHRU_START "Start" +#define MEC1308_CMD_PASSTHRU_EXIT "End_Mode" +#define MEC1308_CMD_PASSTHRU_CS_EN 0xf0 /* chip-select enable */ +#define MEC1308_CMD_PASSTHRU_CS_DIS 0xf1 /* chip-select disable */ +#define MEC1308_CMD_PASSTHRU_SEND 0xf2 /* send byte from data0 */ +#define MEC1308_CMD_PASSTHRU_READ 0xf3 /* read byte, place in data0 */ + +typedef struct +{ + unsigned int in_sio_cfgmode; + unsigned int mbx_idx; /* Mailbox register interface index address */ + unsigned int mbx_data; /* Mailbox register interface data address*/ +} mec1308_data_t; + +static void mec1308_sio_enter(mec1308_data_t *ctx_data, uint16_t port) +{ + if (ctx_data->in_sio_cfgmode) + return; + + OUTB(MEC1308_SIO_ENTRY_KEY, port); + ctx_data->in_sio_cfgmode = 1; +} + +static void mec1308_sio_exit(mec1308_data_t *ctx_data, uint16_t port) +{ + if (!ctx_data->in_sio_cfgmode) + return; + + OUTB(MEC1308_SIO_EXIT_KEY, port); + ctx_data->in_sio_cfgmode = 0; +} + +/** probe for super i/o index + * @port: allocated buffer to store port + * + * returns 0 to indicate success, <0 to indicate error + */ +static int mec1308_get_sio_index(mec1308_data_t *ctx_data, uint16_t *port) +{ + uint16_t ports[] = { MEC1308_SIO_PORT1, + MEC1308_SIO_PORT2, + }; + size_t i; + static uint16_t port_internal, port_found = 0; + + if (port_found) { + *port = port_internal; + return 0; + } + + if (rget_io_perms()) + return -1; + + for (i = 0; i < ARRAY_SIZE(ports); i++) { + uint8_t tmp8; + + /* + * Only after config mode has been successfully entered will the + * index port will read back the last value written to it. + * So we will attempt to enter config mode, set the index + * register, and see if the index register retains the value. + * + * Note: It seems to work "best" when using a device ID register + * as the index and reading from the data port before reading + * the index port. + */ + mec1308_sio_enter(ctx_data, ports[i]); + OUTB(MEC1308_DEVICE_ID_REG, ports[i]); + tmp8 = INB(ports[i] + 1); + tmp8 = INB(ports[i]); + if ((tmp8 != MEC1308_DEVICE_ID_REG)) { + ctx_data->in_sio_cfgmode = 0; + continue; + } + + port_internal = ports[i]; + port_found = 1; + break; + } + + if (!port_found) { + msg_cdbg("\nfailed to obtain super i/o index\n"); + return -1; + } + + msg_cdbg("\nsuper i/o index = 0x%04x\n", port_internal); + *port = port_internal; + return 0; +} + +static uint8_t mbx_read(mec1308_data_t *ctx_data, uint8_t idx) +{ + OUTB(idx, ctx_data->mbx_idx); + return INB(mbx_data); +} + +static int mbx_wait(mec1308_data_t *ctx_data) +{ + int i; + int max_attempts = 10000; + int rc = 0; + + for (i = 0; mbx_read(ctx_data, MEC1308_MBX_CMD); i++) { + if (i == max_attempts) { + rc = 1; + break; + } + /* FIXME: This delay adds determinism to the delay period. It + was chosen arbitrarily thru some experiments. */ + programmer_delay(2); + } + + return rc; +} + +static int mbx_write(mec1308_data_t *ctx_data, uint8_t idx, uint8_t data) +{ + int rc = 0; + + if (idx == MEC1308_MBX_CMD && mbx_wait(ctx_data)) { + msg_perr("%s: command register not clear\n", __func__); + return 1; + } + + OUTB(idx, ctx_data->mbx_idx); + OUTB(data, mbx_data); + + if (idx == MEC1308_MBX_CMD) + rc = mbx_wait(ctx_data); + + return rc; +} + +static void mbx_clear(mec1308_data_t *ctx_data) +{ + int reg; + + for (reg = MEC1308_MBX_DATA_START; reg < MEC1308_MBX_DATA_END; reg++) + mbx_write(ctx_data, reg, 0x00); + mbx_write(ctx_data, MEC1308_MBX_CMD, 0x00); +} + +static int mec1308_exit_passthru_mode(mec1308_data_t *ctx_data) +{ + uint8_t tmp8; + size_t i; + + /* exit passthru mode */ + for (i = 0; i < strlen(MEC1308_CMD_PASSTHRU_EXIT); i++) { + mbx_write(ctx_data, MEC1308_MBX_DATA_START + i, + MEC1308_CMD_PASSTHRU_EXIT[i]); + } + + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_PASSTHRU)) { + msg_pdbg("%s(): exit passthru command timed out\n", __func__); + return 1; + } + + tmp8 = mbx_read(ctx_data, MEC1308_MBX_DATA_START); + msg_pdbg("%s: result: 0x%02x ", __func__, tmp8); + if (tmp8 == MEC1308_CMD_PASSTHRU_SUCCESS) { + msg_pdbg("(exited passthru mode)\n"); + } else if (tmp8 == MEC1308_CMD_PASSTHRU_FAIL) { + msg_pdbg("(failed to exit passthru mode)\n"); + } + + return 0; +} + +static int enter_passthru_mode(mec1308_data_t *ctx_data) +{ + uint8_t tmp8; + size_t i; + + /* + * Enter passthru mode. If the EC does not successfully enter passthru + * mode the first time, we'll clear the mailbox and issue the "exit + * passthru mode" command sequence up to 3 times or until it arrives in + * a known state. + * + * Note: This workaround was developed experimentally. + */ + for (i = 0; i < 3; i++) { + size_t j; + + msg_pdbg("%s(): entering passthru mode, attempt %d out of 3\n", + __func__, (int)(i + 1)); + for (j = 0; j < strlen(MEC1308_CMD_PASSTHRU_ENTER); j++) { + mbx_write(ctx_data, MEC1308_MBX_DATA_START + j, + MEC1308_CMD_PASSTHRU_ENTER[j]); + } + + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_PASSTHRU)) + msg_pdbg("%s(): enter passthru command timed out\n", + __func__); + + tmp8 = mbx_read(ctx_data, MEC1308_MBX_DATA_START); + if (tmp8 == MEC1308_CMD_PASSTHRU_SUCCESS) + break; + + msg_pdbg("%s(): command failed, clearing data registers and " + "issuing full exit passthru command...\n", __func__); + mbx_clear(ctx_data); + mec1308_exit_passthru_mode(ctx_data); + } + + if (tmp8 != MEC1308_CMD_PASSTHRU_SUCCESS) { + msg_perr("%s(): failed to enter passthru mode, result=0x%02x\n", + __func__, tmp8); + return 1; + } + + msg_pdbg("%s(): enter passthru mode return code: 0x%02x\n", + __func__, tmp8); + + /* start passthru mode */ + for (i = 0; i < strlen(MEC1308_CMD_PASSTHRU_START); i++) + mbx_write(ctx_data, MEC1308_MBX_DATA_START + i, + MEC1308_CMD_PASSTHRU_START[i]); + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_PASSTHRU)) { + msg_pdbg("%s(): start passthru command timed out\n", __func__); + return 1; + } + tmp8 = mbx_read(ctx_data, MEC1308_MBX_DATA_START); + if (tmp8 != MEC1308_CMD_PASSTHRU_SUCCESS) { + msg_perr("%s(): failed to enter passthru mode, result=%02x\n", + __func__, tmp8); + return 1; + } + msg_pdbg("%s(): start passthru mode return code: 0x%02x\n", + __func__, tmp8); + + return 0; +} + +static int mec1308_shutdown(void *data) +{ + mec1308_data_t *ctx_data = (mec1308_data_t *)data; + + /* Exit passthru mode before performing commands which do not affect + the SPI ROM */ + mec1308_exit_passthru_mode(ctx_data); + + /* Re-enable SMI and ACPI. + FIXME: is there an ordering dependency? */ + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_SMI_ENABLE)) + msg_pdbg("%s: unable to re-enable SMI\n", __func__); + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_ACPI_ENABLE)) + msg_pdbg("%s: unable to re-enable ACPI\n", __func__); + + free(data); + return 0; +} + +static int mec1308_chip_select(mec1308_data_t *ctx_data) +{ + return mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_PASSTHRU_CS_EN); +} + +static int mec1308_chip_deselect(mec1308_data_t *ctx_data) +{ + return mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_PASSTHRU_CS_DIS); +} + +/* + * MEC1308 will not allow direct access to SPI chip from host if EC is + * connected to LPC bus. This function will forward commands issued thru + * mailbox interface to the SPI flash chip. + */ +static int mec1308_spi_send_command(const struct flashctx *flash, unsigned int writecnt, + unsigned int readcnt, + const unsigned char *writearr, + unsigned char *readarr) +{ + int rc = 0; + size_t i; + mec1308_data_t *ctx_data = (mec1308_data_t *)flash->mst->spi.data; + + if (mec1308_chip_select(ctx_data)) + return 1; + + for (i = 0; i < writecnt; i++) { + if (mbx_write(ctx_data, MEC1308_MBX_DATA_START, writearr[i]) || + mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_PASSTHRU_SEND)) { + msg_pdbg("%s: failed to issue send command\n",__func__); + rc = 1; + goto mec1308_spi_send_command_exit; + } + } + + for (i = 0; i < readcnt; i++) { + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_PASSTHRU_READ)) { + msg_pdbg("%s: failed to issue read command\n",__func__); + rc = 1; + goto mec1308_spi_send_command_exit; + } + readarr[i] = mbx_read(ctx_data, MEC1308_MBX_DATA_START); + } + +mec1308_spi_send_command_exit: + rc |= mec1308_chip_deselect(ctx_data); + return rc; +} + +static struct spi_master spi_master_mec1308 = { + .max_data_read = 256, /* FIXME: should be MAX_DATA_READ_UNLIMITED? */ + .max_data_write = 256, /* FIXME: should be MAX_DATA_WRITE_UNLIMITED? */ + .command = mec1308_spi_send_command, + .multicommand = default_spi_send_multicommand, + .read = default_spi_read, + .write_256 = default_spi_write_256, +}; + +int mec1308_init(void) +{ + uint16_t sio_port; + uint8_t device_id; + uint8_t tmp8; + int ret = 0; + char *p = NULL; + mec1308_data_t *ctx_data = NULL; + + msg_pdbg("%s(): entered\n", __func__); + + ctx_data = calloc(1, sizeof(mec1308_data_t)); + if (!ctx_data) { + msg_perr("Unable to allocate space for extra context data.\n"); + return 1; + } + + p = extract_programmer_param("type"); + if (p && strcmp(p, "ec")) { + msg_pdbg("mec1308 only supports \"ec\" type devices\n"); + ret = 1; + goto mec1308_init_exit; + } + + if (mec1308_get_sio_index(ctx_data, &sio_port) < 0) { + msg_pdbg("MEC1308 not found (probe failed).\n"); + ret = 1; + goto mec1308_init_exit; + } + device_id = sio_read(sio_port, MEC1308_DEVICE_ID_REG); + switch(device_id) { + case MEC1308_DEVICE_ID_VAL: + msg_pdbg("Found EC: MEC1308 (ID:0x%02x,Rev:0x%02x) on " + "sio_port:0x%x.\n", device_id, + sio_read(sio_port, MEC1308_DEVICE_REV), sio_port); + break; + case MEC1310_DEVICE_ID_VAL: + msg_pdbg("Found EC: MEC1310 (ID:0x%02x,Rev:0x%02x) on " + "sio_port:0x%x.\n", device_id, + sio_read(sio_port, MEC1308_DEVICE_REV), sio_port); + break; + default: + msg_pdbg("MEC1308 not found\n"); + ret = 1; + goto mec1308_init_exit; + } + + /* + * setup mailbox interface at LDN 9 + */ + sio_write(sio_port, MEC1308_SIOCFG_LDN, 0x09); + tmp8 = sio_read(sio_port, 0x30); + tmp8 |= 1; + sio_write(sio_port, 0x30, tmp8); /* activate logical device */ + + ctx_data->mbx_idx = (unsigned int)sio_read(sio_port, 0x60) << 8 | + sio_read(sio_port, 0x61); + mbx_data = ctx_data->mbx_idx + 1; + msg_pdbg("%s: mbx_idx: 0x%04x, mbx_data: 0x%04x\n", + __func__, ctx_data->mbx_idx, mbx_data); + + /* Exit Super I/O config mode */ + mec1308_sio_exit(ctx_data, sio_port); + + /* Now that we can read the mailbox, we will wait for any remaining + * command to finish.*/ + if (mbx_wait(ctx_data) != 0) { + msg_perr("%s: mailbox is not available\n", __func__); + ret = 1; + goto mec1308_init_exit; + } + + /* Further setup -- disable SMI and ACPI. + FIXME: is there an ordering dependency? */ + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_ACPI_DISABLE)) { + msg_pdbg("%s: unable to disable ACPI\n", __func__); + ret = 1; + goto mec1308_init_exit; + } + + if (mbx_write(ctx_data, MEC1308_MBX_CMD, MEC1308_CMD_SMI_DISABLE)) { + msg_pdbg("%s: unable to disable SMI\n", __func__); + ret = 1; + goto mec1308_init_exit; + } + + if (register_shutdown(mec1308_shutdown, ctx_data)) { + ret = 1; + goto mec1308_init_exit; + } + + /* + * Enter SPI Pass-Thru Mode after commands which do not require access + * to SPI ROM are complete. We'll start by doing the exit_passthru_mode + * sequence, which is benign if the EC is already in passthru mode. + */ + mec1308_exit_passthru_mode(ctx_data); + + if (enter_passthru_mode(ctx_data)) { + ret = 1; + goto mec1308_init_exit; + } + + internal_buses_supported |= BUS_LPC; /* for LPC <--> SPI bridging */ + spi_master_mec1308.data = ctx_data; + register_spi_master(&spi_master_mec1308); + msg_pdbg("%s(): successfully initialized mec1308\n", __func__); + +mec1308_init_exit: + free(p); + if (ret) + free(ctx_data); + return ret; +} +#endif diff --git a/meson.build b/meson.build index 04176f3..fc79c60 100644 --- a/meson.build +++ b/meson.build @@ -47,6 +47,7 @@ config_it8212 = get_option('config_it8212') config_linux_mtd = get_option('config_linux_mtd') config_linux_spi = get_option('config_linux_spi') +config_mec1308 = get_option('config_mec1308') config_mstarddc_spi = get_option('config_mstarddc_spi') config_nic3com = get_option('config_nic3com') config_nicintel_eeprom = get_option('config_nicintel_eeprom') @@ -214,6 +215,10 @@ srcs += 'linux_spi.c' cargs += '-DCONFIG_LINUX_SPI=1' endif +if config_mec1308 + srcs += 'mec1308.c' + cargs += '-DCONFIG_MEC1308=1' +endif if config_mstarddc_spi srcs += 'mstarddc_spi.c' cargs += '-DCONFIG_MSTARDDC_SPI=1' diff --git a/meson_options.txt b/meson_options.txt index ac48e4e..24a1911 100644 --- a/meson_options.txt +++ b/meson_options.txt @@ -19,6 +19,7 @@ option('config_it8212', type : 'boolean', value : true, description : 'ITE IT8212F PATA') option('config_linux_mtd', type : 'boolean', value : true, description : 'Linux MTD interfaces') option('config_linux_spi', type : 'boolean', value : true, description : 'Linux spidev interfaces') +option('config_mec1308', type : 'boolean', value : false, description : 'Microchip MEC1308 Embedded Controller') option('config_mstarddc_spi', type : 'boolean', value : false, description : 'MSTAR DDC support') option('config_nic3com', type : 'boolean', value : true, description : '3Com NICs') option('config_nicintel_eeprom', type : 'boolean', value : true, description : 'EEPROM on Intel NICs') diff --git a/programmer.h b/programmer.h index c5cab18..6422541 100644 --- a/programmer.h +++ b/programmer.h @@ -109,6 +109,9 @@ #if CONFIG_USBBLASTER_SPI == 1 PROGRAMMER_USBBLASTER_SPI, #endif +#if CONFIG_MEC1308 == 1 + PROGRAMMER_MEC1308, +#endif #if CONFIG_MSTARDDC_SPI == 1 PROGRAMMER_MSTARDDC_SPI, #endif @@ -689,6 +692,11 @@ /* mcp6x_spi.c */ int mcp6x_spi_init(int want_spi); +/* mec1308.c */ +#if CONFIG_MEC1308 == 1 +int mec1308_init(void); +#endif + /* sb600spi.c */ int sb600_probe_spi(struct pci_dev *dev); -- To view, visit https://review.coreboot.org/c/flashrom/+/44541 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I2d51b4bdc0b38b6e488e71b9e774eb6232a2069e Gerrit-Change-Number: 44541 Gerrit-PatchSet: 1 Gerrit-Owner: Victor Ding <victording(a)google.com> Gerrit-MessageType: newchange

5 20

Change in flashrom[master]: Add ENE LPC programmer
by Victor Ding (Code Review) 04 Nov '21

04 Nov '21

Victor Ding has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/44580 ) Change subject: Add ENE LPC programmer ...................................................................... Add ENE LPC programmer Initial support of ENE LPC interface keyboard controller. BUG=b:156140422 BRANCH=none Signed-off-by: Victor Ding <victording(a)google.com> Change-Id: I970afd8c1bd92c159c60e09f22e2f18c0433729d --- M Makefile A ene_lpc.c M flashrom.c M meson.build M meson_options.txt M programmer.h 6 files changed, 642 insertions(+), 0 deletions(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/80/44580/1 diff --git a/Makefile b/Makefile index 803529f..85b4850 100644 --- a/Makefile +++ b/Makefile @@ -170,6 +170,11 @@ else override CONFIG_DEVELOPERBOX_SPI = no endif +ifeq ($(CONFIG_ENE_LPC), yes) +UNSUPPORTED_FEATURES += CONFIG_ENE_LPC=yes +else +override CONFIG_ENE_LPC = no +endif ifeq ($(CONFIG_FT2232_SPI), yes) UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes else @@ -271,6 +276,11 @@ else override CONFIG_ATAPROMISE = no endif +ifeq ($(CONFIG_ENE_LPC), yes) +UNSUPPORTED_FEATURES += CONFIG_ENE_LPC=yes +else +override CONFIG_ENE_LPC = no +endif ifeq ($(CONFIG_IT8212), yes) UNSUPPORTED_FEATURES += CONFIG_IT8212=yes else @@ -381,6 +391,11 @@ else override CONFIG_DEVELOPERBOX_SPI = no endif +ifeq ($(CONFIG_ENE_LPC), yes) +UNSUPPORTED_FEATURES += CONFIG_ENE_LPC=yes +else +override CONFIG_ENE_LPC = no +endif ifeq ($(CONFIG_FT2232_SPI), yes) UNSUPPORTED_FEATURES += CONFIG_FT2232_SPI=yes else @@ -671,6 +686,9 @@ # Promise ATA controller support. CONFIG_ATAPROMISE ?= no +# ENE LPC interface keyboard controller +CONFIG_ENE_LPC ?= yes + # Always enable FT2232 SPI dongles for now. CONFIG_FT2232_SPI ?= yes @@ -855,6 +873,11 @@ NEED_LIBPCI += CONFIG_INTERNAL endif +ifeq ($(CONFIG_ENE_LPC), yes) +FEATURE_CFLAGS += -D'CONFIG_ENE_LPC=1' +PROGRAMMER_OBJS += ene_lpc.o +endif + ifeq ($(CONFIG_SERPROG), yes) FEATURE_CFLAGS += -D'CONFIG_SERPROG=1' PROGRAMMER_OBJS += serprog.o diff --git a/ene_lpc.c b/ene_lpc.c new file mode 100644 index 0000000..701e84e --- /dev/null +++ b/ene_lpc.c @@ -0,0 +1,593 @@ +/* + * This file is part of the flashrom project. + * + * Copyright (C) 2012 Google Inc. + * + * Redistribution and use in source and binary forms, with or without + * modification, are permitted provided that the following conditions + * are met: + * + * Redistributions of source code must retain the above copyright + * notice, this list of conditions and the following disclaimer. + * + * Redistributions in binary form must reproduce the above copyright + * notice, this list of conditions and the following disclaimer in the + * documentation and/or other materials provided with the distribution. + * + * Neither the name of Google or the names of contributors or + * licensors may be used to endorse or promote products derived from this + * software without specific prior written permission. + * + * This software is provided "AS IS," without a warranty of any kind. + * ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND WARRANTIES, + * INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A + * PARTICULAR PURPOSE OR NON-INFRINGEMENT, ARE HEREBY EXCLUDED. + * GOOGLE INC AND ITS LICENSORS SHALL NOT BE LIABLE + * FOR ANY DAMAGES SUFFERED BY LICENSEE AS A RESULT OF USING, MODIFYING + * OR DISTRIBUTING THIS SOFTWARE OR ITS DERIVATIVES. IN NO EVENT WILL + * GOOGLE OR ITS LICENSORS BE LIABLE FOR ANY LOST REVENUE, PROFIT OR DATA, + * OR FOR DIRECT, INDIRECT, SPECIAL, CONSEQUENTIAL, INCIDENTAL OR + * PUNITIVE DAMAGES, HOWEVER CAUSED AND REGARDLESS OF THE THEORY OF + * LIABILITY, ARISING OUT OF THE USE OF OR INABILITY TO USE THIS SOFTWARE, + * EVEN IF GOOGLE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. + */ + +#if defined(__i386__) || defined(__x86_64__) +#include <inttypes.h> +#include <stdlib.h> +#include <string.h> +#include <unistd.h> +#include <sys/time.h> + +#include "chipdrivers.h" +#include "flash.h" +#include "programmer.h" +#include "hwaccess.h" +#include "spi.h" + +/* MCU registers */ +#define REG_EC_HWVER 0xff00 +#define REG_EC_FWVER 0xff01 +#define REG_EC_EDIID 0xff24 +#define REG_8051_CTRL 0xff14 +#define REG_EC_EXTCMD 0xff10 + +#define CPU_RESET 1 + +/* MCU SPI peripheral registers */ +#define REG_SPI_DATA 0xfeab +#define REG_SPI_COMMAND 0xfeac +#define REG_SPI_CONFIG 0xfead + +#define CFG_CSn_FORCE_LOW (1 << 4) +#define CFG_COMMAND_WRITE_ENABLE (1 << 3) +#define CFG_STATUS (1 << 1) +#define CFG_ENABLE_BUSY_STATUS_CHECK (1 << 0) + +/* Timeout */ +#define EC_COMMAND_TIMEOUT 4 +#define EC_RESTART_TIMEOUT 10 +#define ENE_SPI_DELAY_CYCLE 4 +#define EC_PAUSE_TIMEOUT 12 +#define EC_RESET_TRIES 3 + +#define ENE_KB94X_PAUSE_WAKEUP_PORT 0x64 + +#define MASK_INPUT_BUFFER_FULL 2 +#define MASK_OUTPUT_BUFFER_FULL 1 + +const int port_ene_bank = 1; +const int port_ene_offset = 2; +const int port_ene_data = 3; + +/* Supported ENE ECs, ENE_LAST should always be LAST member */ +enum ene_chip_id { + ENE_KB932 = 0, + ENE_KB94X, + ENE_LAST +}; + +/* EC state */ +enum ene_ec_state { + EC_STATE_NORMAL, + EC_STATE_IDLE, + EC_STATE_RESET, + EC_STATE_UNKNOWN +}; + +/* chip-specific parameters */ +typedef struct { + enum ene_chip_id chip_id; + uint8_t hwver; + uint8_t ediid; + uint32_t port_bios; + uint32_t port_ec_command; + uint32_t port_ec_data; + uint8_t ec_reset_cmd; + uint8_t ec_reset_data; + uint8_t ec_restart_cmd; + uint8_t ec_restart_data; + uint8_t ec_pause_cmd; + uint8_t ec_pause_data; + uint16_t ec_status_buf; + uint8_t ec_is_stopping; + uint8_t ec_is_running; + uint8_t ec_is_pausing; + uint32_t port_io_base; +} ene_chip_t; + +typedef struct +{ + /* pointer to table entry of identified chip */ + ene_chip_t *chip; + /* current ec state */ + enum ene_ec_state ec_state; + struct timeval pause_begin; +} ene_lpc_data_t; + +/* table of supported chips + parameters */ +static ene_chip_t ene_chips[] = { + { + ENE_KB932, /* chip_id */ + 0xa2, 0x02, /* hwver + ediid */ + 0x66, /* port_bios */ + 0x6c, 0x68, /* port_ec_{command,data} */ + 0x59, 0xf2, /* ec_reset_{cmd,data} */ + 0x59, 0xf9, /* ec_restart_{cmd,data} */ + 0x59, 0xf1, /* ec_pause_{cmd,data} */ + 0xf554, /* ec_status_buf */ + 0xa5, 0x00, /* ec_is_{stopping,running} masks */ + 0x33, /* ec_is_pausing mask */ + 0xfd60 /* port_io_base */ + }, + { + ENE_KB94X, /* chip_id */ + 0xa3, 0x05, /* hwver + ediid */ + 0x66, /* port_bios */ + 0x66, 0x68, /* port_ec_{command,data} */ + 0x7d, 0x10, /* ec_reset_{cmd,data} */ + 0x7f, 0x10, /* ec_restart_{cmd,data} */ + 0x7e, 0x10, /* ec_pause_{cmd,data} */ + 0xf710, /* ec_status_buf */ + 0x02, 0x00, /* ec_is_{stopping,running} masks */ + 0x01, /* ec_is_pausing mask */ + 0x0380 /* port_io_base */ + } +}; + +static void ec_command(const ene_chip_t *chip, uint8_t cmd, uint8_t data) +{ + struct timeval begin, now; + + /* Spin wait for EC input buffer empty */ + gettimeofday(&begin, NULL); + while (INB(chip->port_ec_command) & MASK_INPUT_BUFFER_FULL) { + gettimeofday(&now, NULL); + if ((now.tv_sec - begin.tv_sec) >= EC_COMMAND_TIMEOUT) { + msg_pdbg("%s: buf not empty\n", __func__); + return; + } + } + + /* Write command */ + OUTB(cmd, chip->port_ec_command); + + if (chip->chip_id == ENE_KB932) { + /* Spin wait for EC input buffer empty */ + gettimeofday(&begin, NULL); + while (INB(chip->port_ec_command) & + MASK_INPUT_BUFFER_FULL) { + gettimeofday(&now, NULL); + if ((now.tv_sec - begin.tv_sec) >= + EC_COMMAND_TIMEOUT) { + msg_pdbg("%s: buf not empty\n", __func__); + return; + } + } + /* Write data */ + OUTB(data, chip->port_ec_data); + } +} + +static uint8_t ene_read(const ene_chip_t *chip, uint16_t addr) +{ + uint8_t bank; + uint8_t offset; + uint8_t data; + uint32_t port_io_base; + + bank = addr >> 8; + offset = addr & 0xff; + port_io_base = chip->port_io_base; + + OUTB(bank, port_io_base + port_ene_bank); + OUTB(offset, port_io_base + port_ene_offset); + data = INB(port_io_base + port_ene_data); + + return data; +} + +static void ene_write(const ene_chip_t *chip, uint16_t addr, uint8_t data) +{ + uint8_t bank; + uint8_t offset; + uint32_t port_io_base; + + bank = addr >> 8; + offset = addr & 0xff; + port_io_base = chip->port_io_base; + + OUTB(bank, port_io_base + port_ene_bank); + OUTB(offset, port_io_base + port_ene_offset); + + OUTB(data, port_io_base + port_ene_data); +} + +/** + * wait_cycles, wait for n LPC bus clock cycles + * + * @param n: number of LPC cycles to wait + * @return void + */ +static void wait_cycles(const ene_chip_t *chip,int n) +{ + while (n--) + INB(chip->port_io_base + port_ene_bank); +} + +static int is_spicmd_write(uint8_t cmd) +{ + switch (cmd) { + case JEDEC_WREN: + /* Chip Write Enable */ + case JEDEC_EWSR: + /* Write Status Enable */ + case JEDEC_CE_60: + /* Chip Erase 0x60 */ + case JEDEC_CE_C7: + /* Chip Erase 0xc7 */ + case JEDEC_BE_52: + /* Block Erase 0x52 */ + case JEDEC_BE_D8: + /* Block Erase 0xd8 */ + case JEDEC_BE_D7: + /* Block Erase 0xd7 */ + case JEDEC_SE: + /* Sector Erase */ + case JEDEC_BYTE_PROGRAM: + /* Write memory byte */ + case JEDEC_AAI_WORD_PROGRAM: + /* Write AAI word */ + return 1; + } + return 0; +} + +static void ene_spi_start(const ene_chip_t *chip) +{ + int cfg; + + cfg = ene_read(chip, REG_SPI_CONFIG); + cfg |= CFG_CSn_FORCE_LOW; + cfg |= CFG_COMMAND_WRITE_ENABLE; + ene_write(chip, REG_SPI_CONFIG, cfg); + + wait_cycles(chip, ENE_SPI_DELAY_CYCLE); +} + +static void ene_spi_end(const ene_chip_t *chip) +{ + int cfg; + + cfg = ene_read(chip, REG_SPI_CONFIG); + cfg &= ~CFG_CSn_FORCE_LOW; + cfg |= CFG_COMMAND_WRITE_ENABLE; + ene_write(chip, REG_SPI_CONFIG, cfg); + + wait_cycles(chip, ENE_SPI_DELAY_CYCLE); +} + +static int ene_spi_wait(const ene_chip_t *chip) +{ + struct timeval begin, now; + + gettimeofday(&begin, NULL); + while(ene_read(chip, REG_SPI_CONFIG) & CFG_STATUS) { + gettimeofday(&now, NULL); + if ((now.tv_sec - begin.tv_sec) >= EC_COMMAND_TIMEOUT) { + msg_pdbg("%s: spi busy\n", __func__); + return 1; + } + } + return 0; +} + +static int ene_pause_ec(ene_lpc_data_t *ctx_data) +{ + struct timeval begin, now; + const ene_chip_t *chip = ctx_data->chip; + + if (!chip->ec_pause_cmd) + return -1; + + /* EC prepare pause */ + ec_command(chip, chip->ec_pause_cmd, chip->ec_pause_data); + + gettimeofday(&begin, NULL); + /* Spin wait for EC ready */ + while (ene_read(chip, chip->ec_status_buf) != + chip->ec_is_pausing) { + gettimeofday(&now, NULL); + if ((now.tv_sec - begin.tv_sec) >= + EC_COMMAND_TIMEOUT) { + msg_pdbg("%s: unable to pause ec\n", __func__); + return -1; + } + } + + + gettimeofday(&ctx_data->pause_begin, NULL); + ctx_data->ec_state = EC_STATE_IDLE; + return 0; +} + +static int ene_resume_ec(ene_lpc_data_t *ctx_data) +{ + struct timeval begin, now; + const ene_chip_t *chip = ctx_data->chip; + + if (chip->chip_id == ENE_KB94X) + OUTB(0xff, ENE_KB94X_PAUSE_WAKEUP_PORT); + else + /* Trigger 8051 interrupt to resume */ + ene_write(chip, REG_EC_EXTCMD, 0xff); + + gettimeofday(&begin, NULL); + while (ene_read(chip, chip->ec_status_buf) != + chip->ec_is_running) { + gettimeofday(&now, NULL); + if ((now.tv_sec - begin.tv_sec) >= + EC_COMMAND_TIMEOUT) { + msg_pdbg("%s: unable to resume ec\n", __func__); + return -1; + } + } + + ctx_data->ec_state = EC_STATE_NORMAL; + return 0; +} + +static int ene_pause_timeout_check(ene_lpc_data_t *ctx_data) +{ + struct timeval pause_now; + gettimeofday(&pause_now, NULL); + if ((pause_now.tv_sec - ctx_data->pause_begin.tv_sec) >= + EC_PAUSE_TIMEOUT) { + if(ene_resume_ec(ctx_data) == 0) + ene_pause_ec(ctx_data); + + } + return 0; +} + +static int ene_reset_ec(ene_lpc_data_t *ctx_data) +{ + uint8_t reg; + struct timeval begin, now; + const ene_chip_t *chip = ctx_data->chip; + + gettimeofday(&begin, NULL); + + /* EC prepare reset */ + ec_command(chip, chip->ec_reset_cmd, chip->ec_reset_data); + + /* Spin wait for EC ready */ + while (ene_read(chip, chip->ec_status_buf) != + chip->ec_is_stopping) { + gettimeofday(&now, NULL); + if ((now.tv_sec - begin.tv_sec) >= + EC_COMMAND_TIMEOUT) { + msg_pdbg("%s: unable to reset ec\n", __func__); + return -1; + } + } + + /* Wait 1 second */ + sleep(1); + + /* Reset 8051 */ + reg = ene_read(chip, REG_8051_CTRL); + reg |= CPU_RESET; + ene_write(chip, REG_8051_CTRL, reg); + + ctx_data->ec_state = EC_STATE_RESET; + return 0; +} + +static int ene_enter_flash_mode(ene_lpc_data_t *ctx_data) +{ + if (ene_pause_ec(ctx_data)) + return ene_reset_ec(ctx_data); + return 0; +} + +static int ene_spi_send_command(const struct flashctx *flash, + unsigned int writecnt, + unsigned int readcnt, + const unsigned char *writearr, + unsigned char *readarr) +{ + unsigned int i; + int tries = EC_RESET_TRIES; + ene_lpc_data_t *ctx_data = (ene_lpc_data_t *)flash->mst->spi.data; + const ene_chip_t *chip = ctx_data->chip; + + if (ctx_data->ec_state == EC_STATE_IDLE && is_spicmd_write(writearr[0])) { + do { + /* Enter reset mode if we need to write/erase */ + if (ene_resume_ec(ctx_data)) + continue; + + if (!ene_reset_ec(ctx_data)) + break; + } while (--tries > 0); + + if (!tries) { + msg_perr("%s: EC failed reset, skipping write\n", __func__); + ctx_data->ec_state = EC_STATE_IDLE; + return 1; + } + } + else if(chip->chip_id == ENE_KB94X && ctx_data->ec_state == EC_STATE_IDLE) + ene_pause_timeout_check(ctx_data); + + ene_spi_start(chip); + + for (i = 0; i < writecnt; i++) { + ene_write(chip, REG_SPI_COMMAND, writearr[i]); + if (ene_spi_wait(chip)) { + msg_pdbg("%s: write count %d\n", __func__, i); + return 1; + } + } + + for (i = 0; i < readcnt; i++) { + /* Push data by clock the serial bus */ + ene_write(chip, REG_SPI_COMMAND, 0); + if (ene_spi_wait(chip)) { + msg_pdbg("%s: read count %d\n", __func__, i); + return 1; + } + readarr[i] = ene_read(chip, REG_SPI_DATA); + if (ene_spi_wait(chip)) { + msg_pdbg("%s: read count %d\n", __func__, i); + return 1; + } + } + + ene_spi_end(chip); + return 0; +} + +static int ene_leave_flash_mode(void *data) +{ + ene_lpc_data_t *ctx_data = (ene_lpc_data_t *)data; + const ene_chip_t *chip = ctx_data->chip; + int rv = 0; + uint8_t reg; + struct timeval begin, now; + + if (ctx_data->ec_state == EC_STATE_RESET) { + reg = ene_read(chip, REG_8051_CTRL); + reg &= ~CPU_RESET; + ene_write(chip, REG_8051_CTRL, reg); + + gettimeofday(&begin, NULL); + /* EC restart */ + while (ene_read(chip, chip->ec_status_buf) != + chip->ec_is_running) { + gettimeofday(&now, NULL); + if ((now.tv_sec - begin.tv_sec) >= + EC_RESTART_TIMEOUT) { + msg_pdbg("%s: ec restart busy\n", __func__); + rv = 1; + goto exit; + } + } + msg_pdbg("%s: send ec restart\n", __func__); + ec_command(chip, chip->ec_restart_cmd, + chip->ec_restart_data); + + ctx_data->ec_state = EC_STATE_NORMAL; + rv = 0; + goto exit; + } + + rv = ene_resume_ec(ctx_data); + +exit: + /* + * Trigger ec interrupt after pause/reset by sending 0x80 + * to bios command port. + */ + OUTB(0x80, chip->port_bios); + free(data); + return rv; +} + +static struct spi_master spi_master_ene = { + .max_data_read = 256, + .max_data_write = 256, + .command = ene_spi_send_command, + .multicommand = default_spi_send_multicommand, + .read = default_spi_read, + .write_256 = default_spi_write_256, +}; + +int ene_lpc_init() +{ + uint8_t hwver, ediid, i; + int ret = 0; + char *p = NULL; + ene_lpc_data_t *ctx_data = NULL; + + msg_pdbg("%s\n", __func__); + + ctx_data = calloc(1, sizeof(ene_lpc_data_t)); + if (!ctx_data) { + msg_perr("Unable to allocate space for extra context data.\n"); + return 1; + } + ctx_data->ec_state = EC_STATE_NORMAL; + + p = extract_programmer_param("type"); + if (p && strcmp(p, "ec")) { + msg_pdbg("ene_lpc only supports \"ec\" type devices\n"); + ret = 1; + goto ene_probe_spi_flash_exit; + } + + for (i = 0; i < ENE_LAST; ++i) { + ctx_data->chip = &ene_chips[i]; + + hwver = ene_read(ctx_data->chip, REG_EC_HWVER); + ediid = ene_read(ctx_data->chip, REG_EC_EDIID); + + if(hwver == ene_chips[i].hwver && + ediid == ene_chips[i].ediid) { + break; + } + } + + if (i == ENE_LAST) { + msg_pdbg("ENE EC not found (probe failed)\n"); + ret = 1; + goto ene_probe_spi_flash_exit; + } + + /* TODO: probe the EC stop protocol + * + * Compal - ec_command(0x41, 0xa1) returns 43 4f 4d 50 41 4c 9c + */ + + + if (register_shutdown(ene_leave_flash_mode, ctx_data)) { + ret = 1; + goto ene_probe_spi_flash_exit; + } + + ene_enter_flash_mode(ctx_data); + + internal_buses_supported |= BUS_LPC; + spi_master_ene.data = ctx_data; + register_spi_master(&spi_master_ene); + msg_pdbg("%s: successfully initialized ene\n", __func__); + +ene_probe_spi_flash_exit: + free(p); + if (ret) + free(ctx_data); + return ret; +} + +#endif /* __i386__ || __x86_64__ */ diff --git a/flashrom.c b/flashrom.c index 4a30986..35ac6f5 100644 --- a/flashrom.c +++ b/flashrom.c @@ -279,6 +279,18 @@ }, #endif +#if CONFIG_ENE_LPC == 1 + { + .name = "ene_lpc", + .type = OTHER, + .devs.note = "ENE LPC interface keyboard controller\n", + .init = ene_lpc_init, + .map_flash_region = fallback_map, + .unmap_flash_region = fallback_unmap, + .delay = internal_delay, + }, +#endif + #if CONFIG_RAYER_SPI == 1 { .name = "rayer_spi", diff --git a/meson.build b/meson.build index 04176f3..180b5dd 100644 --- a/meson.build +++ b/meson.build @@ -40,6 +40,7 @@ config_digilent_spi = get_option('config_digilent_spi') config_drkaiser = get_option('config_drkaiser') config_dummy = get_option('config_dummy') +config_ene_lpc = get_option('config_ene_lpc') config_ft2232_spi = get_option('config_ft2232_spi') config_gfxnvidia = get_option('config_gfxnvidia') config_raiden = get_option('config_raiden') @@ -202,6 +203,10 @@ cargs += '-DCONFIG_INTERNAL_DMI=1' endif endif +if config_ene_lpc + srcs += 'ene_lpc.c' + cargs += '-DCONFIG_ENE_LPC=1' +endif if config_it8212 srcs += 'it8212.c' cargs += '-DCONFIG_IT8212=1' diff --git a/meson_options.txt b/meson_options.txt index ac48e4e..ba5130b 100644 --- a/meson_options.txt +++ b/meson_options.txt @@ -11,6 +11,7 @@ option('config_digilent_spi', type : 'boolean', value : true, description : 'Digilent Development board JTAG') option('config_drkaiser', type : 'boolean', value : true, description : 'Dr. Kaiser') option('config_dummy', type : 'boolean', value : true, description : 'dummy tracing') +option('config_ene_lpc', type : 'boolean', value : true, description : 'ENE LPC interface keyboard controller') option('config_ft2232_spi', type : 'boolean', value : true, description : 'FT2232 SPI dongles') option('config_gfxnvidia', type : 'boolean', value : true, description : 'NVIDIA graphics cards') option('config_raiden', type : 'boolean', value : true, description : 'ChromiumOS Servo DUT debug board') diff --git a/programmer.h b/programmer.h index c5cab18..b3bc700 100644 --- a/programmer.h +++ b/programmer.h @@ -61,6 +61,9 @@ #if CONFIG_ATAPROMISE == 1 PROGRAMMER_ATAPROMISE, #endif +#if CONFIG_ENE_LPC == 1 + PROGRAMMER_ENE_LPC, +#endif #if CONFIG_IT8212 == 1 PROGRAMMER_IT8212, #endif @@ -578,6 +581,11 @@ extern const struct dev_entry devs_digilent_spi[]; #endif +/* ene_lpc.c */ +#if CONFIG_ENE_LPC == 1 +int ene_lpc_init(void); +#endif + /* jlink_spi.c */ #if CONFIG_JLINK_SPI == 1 int jlink_spi_init(void); -- To view, visit https://review.coreboot.org/c/flashrom/+/44580 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I970afd8c1bd92c159c60e09f22e2f18c0433729d Gerrit-Change-Number: 44580 Gerrit-PatchSet: 1 Gerrit-Owner: Victor Ding <victording(a)google.com> Gerrit-MessageType: newchange

4 14

Change in flashrom[master]: chipset_enable.c: Mark Intel Q67 as DEP
by Angel Pons (Code Review) 01 Nov '21

01 Nov '21

Angel Pons has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/47797 ) Change subject: chipset_enable.c: Mark Intel Q67 as DEP ...................................................................... chipset_enable.c: Mark Intel Q67 as DEP Tested reading, writing and erasing the internal flash chip using an HP Elite 8200 mainboard with an Intel Q67 PCH. However, since ME-enabled chipsets are marked as DEP instead of OK, this one shall also be. Change-Id: I2bd431c5c72824654b6b5b840f9af55dfe9d3554 Signed-off-by: Angel Pons <th3fanbus(a)gmail.com> --- M chipset_enable.c 1 file changed, 1 insertion(+), 1 deletion(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/97/47797/1 diff --git a/chipset_enable.c b/chipset_enable.c index 04ff9d8..5e4a547 100644 --- a/chipset_enable.c +++ b/chipset_enable.c @@ -1829,7 +1829,7 @@ {0x8086, 0x1c4b, B_FS, NT, "Intel", "HM67", enable_flash_pch6}, {0x8086, 0x1c4c, B_FS, NT, "Intel", "Q65", enable_flash_pch6}, {0x8086, 0x1c4d, B_FS, NT, "Intel", "QS67", enable_flash_pch6}, - {0x8086, 0x1c4e, B_FS, NT, "Intel", "Q67", enable_flash_pch6}, + {0x8086, 0x1c4e, B_FS, DEP, "Intel", "Q67", enable_flash_pch6}, {0x8086, 0x1c4f, B_FS, DEP, "Intel", "QM67", enable_flash_pch6}, {0x8086, 0x1c50, B_FS, NT, "Intel", "B65", enable_flash_pch6}, {0x8086, 0x1c52, B_FS, NT, "Intel", "C202", enable_flash_pch6}, -- To view, visit https://review.coreboot.org/c/flashrom/+/47797 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I2bd431c5c72824654b6b5b840f9af55dfe9d3554 Gerrit-Change-Number: 47797 Gerrit-PatchSet: 1 Gerrit-Owner: Angel Pons <th3fanbus(a)gmail.com> Gerrit-MessageType: newchange

4 5

Change in ...flashrom[master]: freebsd_spi: Use malloc() instead of alloca()
by David Hendricks (Code Review) 10 Oct '21

10 Oct '21

David Hendricks has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/30765 Change subject: freebsd_spi: Use malloc() instead of alloca() ...................................................................... freebsd_spi: Use malloc() instead of alloca() Change-Id: I03ff2bd1e20bea014333945771b560f17387ebd6 Signed-off-by: David Hendricks <david.hendricks(a)gmail.com> --- M freebsd_spi.c 1 file changed, 7 insertions(+), 1 deletion(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/65/30765/1 diff --git a/freebsd_spi.c b/freebsd_spi.c index 215be20..7514912 100644 --- a/freebsd_spi.c +++ b/freebsd_spi.c @@ -145,7 +145,11 @@ /* FreeBSD uses a single buffer for rx and tx. Allocate a temporary one to avoid overwriting anything. */ size_t tmpcnt = readcnt + writecnt; - unsigned char *tmpbuf = alloca(tmpcnt); + unsigned char *tmpbuf = malloc(tmpcnt); + if (!tmpbuf) { + msg_perr("Out of memory!\n"); + return -1; + } bzero(tmpbuf, tmpcnt); memcpy(tmpbuf, txbuf, writecnt); @@ -164,12 +168,14 @@ if (ioctl(fd, SPIGENIOC_TRANSFER, &msg) == -1) { msg_cerr("%s: ioctl: %s\n", __func__, strerror(errno)); + free(tmpbuf); return -1; } if (rxbuf) memcpy(rxbuf, tmpbuf + writecnt, readcnt); + free(tmpbuf); return 0; } -- To view, visit https://review.coreboot.org/c/flashrom/+/30765 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I03ff2bd1e20bea014333945771b560f17387ebd6 Gerrit-Change-Number: 30765 Gerrit-PatchSet: 1 Gerrit-Owner: David Hendricks <david.hendricks(a)gmail.com> Gerrit-MessageType: newchange

1 1

Change in ...flashrom[master]: Add freebsd_spi programmer
by David Hendricks (Code Review) 10 Oct '21

10 Oct '21

David Hendricks has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/30764 Change subject: Add freebsd_spi programmer ...................................................................... Add freebsd_spi programmer Based on linux_spi, using FreeBSD's spigen(4) interface. Change-Id: I4e1689416fbb309df94807f51635bc1f4b53e0c8 Signed-off-by: Greg V <greg(a)unrelenting.technology> --- M Makefile M flashrom.8.tmpl M flashrom.c A freebsd_spi.c M programmer.h 5 files changed, 246 insertions(+), 0 deletions(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/64/30764/1 diff --git a/Makefile b/Makefile index 1ff578c..7e709dc 100644 --- a/Makefile +++ b/Makefile @@ -379,6 +379,14 @@ endif endif +ifneq ($(TARGET_OS), FreeBSD) +ifeq ($(CONFIG_FREEBSD_SPI), yes) +UNSUPPORTED_FEATURES += CONFIG_FREEBSD_SPI=yes +else +override CONFIG_FREEBSD_SPI = no +endif +endif + ############################################################################### # General architecture-specific settings. # Like above for the OS, below we verify user-supplied options depending on the target architecture. @@ -647,6 +655,9 @@ CONFIG_LINUX_MTD ?= yes CONFIG_LINUX_SPI ?= yes +# Enable FreeBSD spigen interface by default. We disable them on non-FreeBSD targets. +CONFIG_FREEBSD_SPI ?= yes + # Always enable ITE IT8212F PATA controllers for now. CONFIG_IT8212 ?= yes @@ -945,6 +956,11 @@ PROGRAMMER_OBJS += linux_spi.o endif +ifeq ($(CONFIG_FREEBSD_SPI), yes) +FEATURE_CFLAGS += -D'CONFIG_FREEBSD_SPI=1' +PROGRAMMER_OBJS += freebsd_spi.o +endif + ifeq ($(CONFIG_MSTARDDC_SPI), yes) # This is a totally ugly hack. FEATURE_CFLAGS += $(call debug_shell,grep -q "LINUX_I2C_SUPPORT := yes" .features && printf "%s" "-D'CONFIG_MSTARDDC_SPI=1'") diff --git a/flashrom.8.tmpl b/flashrom.8.tmpl index c557af7..092f070 100644 --- a/flashrom.8.tmpl +++ b/flashrom.8.tmpl @@ -319,6 +319,8 @@ .sp .BR "* linux_spi" " (for SPI flash ROMs accessible via /dev/spidevX.Y on Linux)" .sp +.BR "* freebsd_spi" " (for SPI flash ROMs accessible via /dev/spigenX.Y on FreeBSD)" +.sp .BR "* usbblaster_spi" " (for SPI flash ROMs attached to an Altera USB-Blaster compatible cable)" .sp .BR "* nicintel_eeprom" " (for SPI EEPROMs on Intel Gigabit network cards)" @@ -1065,6 +1067,25 @@ .sp Please note that the linux_spi driver only works on Linux. .SS +.BR "freebsd_spi " programmer +.IP +You have to specify the SPI controller to use with the +.sp +.B " flashrom \-p freebsd_spi:dev=/dev/spigenX.Y" +.sp +syntax where +.B /dev/spigenX.Y +is the FreeBSD device node for your SPI controller. +.sp +In case the device supports it, you can set the SPI clock frequency with the optional +.B spispeed +parameter. The frequency is parsed as kilohertz. +Example that sets the frequency to 8 MHz: +.sp +.B " flashrom \-p freebsd_spi:dev=/dev/spigenX.Y,spispeed=8000" +.sp +Please note that the freebsd_spi driver only works on FreeBSD. +.SS .BR "mstarddc_spi " programmer .IP The Display Data Channel (DDC) is an I2C bus present on VGA and DVI connectors, that allows exchanging diff --git a/flashrom.c b/flashrom.c index 59a7531..624bcfb 100644 --- a/flashrom.c +++ b/flashrom.c @@ -377,6 +377,18 @@ }, #endif +#if CONFIG_FREEBSD_SPI == 1 + { + .name = "freebsd_spi", + .type = OTHER, + .devs.note = "Device files /dev/spigen*.*\n", + .init = freebsd_spi_init, + .map_flash_region = fallback_map, + .unmap_flash_region = fallback_unmap, + .delay = internal_delay, + }, +#endif + #if CONFIG_USBBLASTER_SPI == 1 { .name = "usbblaster_spi", diff --git a/freebsd_spi.c b/freebsd_spi.c new file mode 100644 index 0000000..215be20 --- /dev/null +++ b/freebsd_spi.c @@ -0,0 +1,186 @@ +/* + * This file is part of the flashrom project. + * + * Copyright (C) 2011 Sven Schnelle <svens(a)stackframe.org> + * Copyright (C) 2018 Greg V <greg(a)unrelenting.technology> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; version 2 of the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#if CONFIG_FREEBSD_SPI == 1 + +#include <stdio.h> +#include <string.h> +#include <stdlib.h> +#include <fcntl.h> +#include <errno.h> +#include <ctype.h> +#include <unistd.h> +#include <sys/ioctl.h> +#include <sys/types.h> +#include <sys/ioccom.h> +#include <sys/spigenio.h> +#include "flash.h" +#include "chipdrivers.h" +#include "programmer.h" +#include "spi.h" + +/* Tested on: + * Xunlong Orange Pi PC (Allwinner H3) */ + +/* Same as in spi(8) */ +#define DEFAULT_BUFFER_SIZE 8192 + +static int fd = -1; + +static int freebsd_spi_shutdown(void *data); +static int freebsd_spi_send_command(struct flashctx *flash, unsigned int writecnt, + unsigned int readcnt, + const unsigned char *txbuf, + unsigned char *rxbuf); +static int freebsd_spi_read(struct flashctx *flash, uint8_t *buf, + unsigned int start, unsigned int len); +static int freebsd_spi_write_256(struct flashctx *flash, const uint8_t *buf, + unsigned int start, unsigned int len); + +static const struct spi_master spi_master_freebsd = { + .type = SPI_CONTROLLER_FREEBSD, + .features = SPI_MASTER_4BA, + .max_data_read = MAX_DATA_UNSPECIFIED, /* TODO? */ + .max_data_write = MAX_DATA_UNSPECIFIED, /* TODO? */ + .command = freebsd_spi_send_command, + .multicommand = default_spi_send_multicommand, + .read = freebsd_spi_read, + .write_256 = freebsd_spi_write_256, + .write_aai = default_spi_write_aai, +}; + +int freebsd_spi_init(void) +{ + char *p, *endp, *dev; + uint32_t speed_hz = 0; + /* FIXME: make the following configurable by CLI options. */ + /* SPI mode 0 (beware this also includes: MSB first, CS active low and others */ + const uint8_t mode = 0; + + p = extract_programmer_param("spispeed"); + if (p && strlen(p)) { + speed_hz = (uint32_t)strtoul(p, &endp, 10) * 1000; + if (p == endp) { + msg_perr("%s: invalid clock: %s kHz\n", __func__, p); + free(p); + return 1; + } + } + free(p); + + dev = extract_programmer_param("dev"); + if (!dev || !strlen(dev)) { + msg_perr("No SPI device given. Use flashrom -p " + "freebsd_spi:dev=/dev/spigenX.Y\n"); + free(dev); + return 1; + } + + msg_pdbg("Using device %s\n", dev); + if ((fd = open(dev, O_RDWR)) == -1) { + msg_perr("%s: failed to open %s: %s\n", __func__, + dev, strerror(errno)); + free(dev); + return 1; + } + free(dev); + + if (register_shutdown(freebsd_spi_shutdown, NULL)) + return 1; + /* We rely on the shutdown function for cleanup from here on. */ + + if (speed_hz > 0) { + if (ioctl(fd, SPIGENIOC_SET_CLOCK_SPEED, &speed_hz) == -1) { + msg_perr("%s: failed to set speed to %d Hz: %s\n", + __func__, speed_hz, strerror(errno)); + return 1; + } + + msg_pdbg("Using %d kHz clock\n", speed_hz/1000); + } + + if (ioctl(fd, SPIGENIOC_SET_SPI_MODE, &mode) == -1) { + msg_perr("%s: failed to set SPI mode to 0x%02x: %s\n", + __func__, mode, strerror(errno)); + return 1; + } + + register_spi_master(&spi_master_freebsd); + return 0; +} + +static int freebsd_spi_shutdown(void *data) +{ + if (fd != -1) { + close(fd); + fd = -1; + } + return 0; +} + +static int freebsd_spi_send_command(struct flashctx *flash, unsigned int writecnt, + unsigned int readcnt, + const unsigned char *txbuf, + unsigned char *rxbuf) +{ + if (fd == -1) + return -1; + /* The implementation currently does not support requests that + don't start with sending a command. */ + if (writecnt == 0) + return SPI_INVALID_LENGTH; + + /* FreeBSD uses a single buffer for rx and tx. Allocate a temporary one to avoid overwriting anything. */ + size_t tmpcnt = readcnt + writecnt; + unsigned char *tmpbuf = alloca(tmpcnt); + + bzero(tmpbuf, tmpcnt); + memcpy(tmpbuf, txbuf, writecnt); + + /* Command/data separation is pretty useless, spi(8) only uses the command. */ + struct spigen_transfer msg = { + .st_command = { + .iov_base = (void*)tmpbuf, + .iov_len = tmpcnt, + }, + .st_data = { + .iov_base = NULL, + .iov_len = 0, + }, + }; + + if (ioctl(fd, SPIGENIOC_TRANSFER, &msg) == -1) { + msg_cerr("%s: ioctl: %s\n", __func__, strerror(errno)); + return -1; + } + + if (rxbuf) + memcpy(rxbuf, tmpbuf + writecnt, readcnt); + + return 0; +} + +static int freebsd_spi_read(struct flashctx *flash, uint8_t *buf, unsigned int start, unsigned int len) +{ + return spi_read_chunked(flash, buf, start, len, DEFAULT_BUFFER_SIZE); +} + +static int freebsd_spi_write_256(struct flashctx *flash, const uint8_t *buf, unsigned int start, unsigned int len) +{ + return spi_write_chunked(flash, buf, start, len, DEFAULT_BUFFER_SIZE); +} + +#endif // CONFIG_FREEBSD_SPI == 1 diff --git a/programmer.h b/programmer.h index 311992a..30687ed 100644 --- a/programmer.h +++ b/programmer.h @@ -103,6 +103,9 @@ #if CONFIG_LINUX_SPI == 1 PROGRAMMER_LINUX_SPI, #endif +#if CONFIG_FREEBSD_SPI == 1 + PROGRAMMER_FREEBSD_SPI, +#endif #if CONFIG_USBBLASTER_SPI == 1 PROGRAMMER_USBBLASTER_SPI, #endif @@ -548,6 +551,11 @@ int linux_spi_init(void); #endif +/* freebsd_spi.c */ +#if CONFIG_FREEBSD_SPI == 1 +int freebsd_spi_init(void); +#endif + /* dediprog.c */ #if CONFIG_DEDIPROG == 1 int dediprog_init(void); @@ -623,6 +631,9 @@ #if CONFIG_LINUX_SPI == 1 SPI_CONTROLLER_LINUX, #endif +#if CONFIG_FREEBSD_SPI == 1 + SPI_CONTROLLER_FREEBSD, +#endif #if CONFIG_SERPROG == 1 SPI_CONTROLLER_SERPROG, #endif -- To view, visit https://review.coreboot.org/c/flashrom/+/30764 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I4e1689416fbb309df94807f51635bc1f4b53e0c8 Gerrit-Change-Number: 30764 Gerrit-PatchSet: 1 Gerrit-Owner: David Hendricks <david.hendricks(a)gmail.com> Gerrit-MessageType: newchange

1 2

Change in flashrom[master]: util/ich_descriptors_tool: Use GNU-style printf in MinGW
by David Hendricks (Code Review) 01 Oct '21

01 Oct '21

David Hendricks has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/43052 ) Change subject: util/ich_descriptors_tool: Use GNU-style printf in MinGW ...................................................................... util/ich_descriptors_tool: Use GNU-style printf in MinGW This allows MinGW targets to use certain printf formatting identifiers such as "%v" by adding -D__USE_MINGW_ANSI_STDIO=1 to the CFLAGS. This is also done in flashrom's top-level Makefile. Reported on https://github.com/flashrom/flashrom/issues/149 Change-Id: I644be8b5b607cc77b4be2121c443f0d41d8da687 Signed-off-by: David Hendricks <david.hendricks(a)gmail.com> --- M util/ich_descriptors_tool/Makefile 1 file changed, 4 insertions(+), 0 deletions(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/52/43052/1 diff --git a/util/ich_descriptors_tool/Makefile b/util/ich_descriptors_tool/Makefile index c32e30b..8962431 100644 --- a/util/ich_descriptors_tool/Makefile +++ b/util/ich_descriptors_tool/Makefile @@ -41,6 +41,10 @@ CFLAGS += -Wno-format endif +ifeq ($(TARGET_OS), MinGW) +CFLAGS += -D__USE_MINGW_ANSI_STDIO=1 +endif + ifeq ($(WARNERROR), yes) CFLAGS += -Werror endif -- To view, visit https://review.coreboot.org/c/flashrom/+/43052 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I644be8b5b607cc77b4be2121c443f0d41d8da687 Gerrit-Change-Number: 43052 Gerrit-PatchSet: 1 Gerrit-Owner: David Hendricks <david.hendricks(a)gmail.com> Gerrit-MessageType: newchange

4 5

Change in flashrom[master]: ft2232_spi.c: change the chunksize to 280
by Simon Buhrow (Code Review) 27 Sep '21

27 Sep '21

Simon Buhrow has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/43282 ) Change subject: ft2232_spi.c: change the chunksize to 280 ...................................................................... ft2232_spi.c: change the chunksize to 280 Signed-off-by: Simon Buhrow <simon.buhrow(a)posteo.de> Change-Id: I5e096937834fc8fc8623c8c59ade529de081b72a --- M ft2232_spi.c 1 file changed, 12 insertions(+), 1 deletion(-) git pull ssh://review.coreboot.org:29418/flashrom refs/changes/82/43282/1 diff --git a/ft2232_spi.c b/ft2232_spi.c index 0799af4..0a8d631 100644 --- a/ft2232_spi.c +++ b/ft2232_spi.c @@ -398,7 +398,18 @@ msg_perr("Unable to set latency timer (%s).\n", ftdi_get_error_string(ftdic)); } - if (ftdi_write_data_set_chunksize(ftdic, 270)) { + if (ftdi_write_data_set_chunksize(ftdic, 280)) { + /* + * 280 bytes = + * + 9 B (CMD) + * + 1 B (WREN) + * + 9 B (CMD) + * + 1 B (op) + * + 4 B (addr) + * + 256 B (page data) + * + * With op: PageProgram or Erase; CMD: FTDI-Chip commands + */ msg_perr("Unable to set chunk size (%s).\n", ftdi_get_error_string(ftdic)); } -- To view, visit https://review.coreboot.org/c/flashrom/+/43282 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I5e096937834fc8fc8623c8c59ade529de081b72a Gerrit-Change-Number: 43282 Gerrit-PatchSet: 1 Gerrit-Owner: Simon Buhrow Gerrit-MessageType: newchange

4 17

Change in flashrom[master]: Add support for Intel Emmitsburg PCH
by Jonathan Zhang (Code Review) 31 Aug '21

31 Aug '21

Attention is currently required from: Arthur Heymans, Johnny Lin, David Hendricks, Edward O'Callaghan, Deomid "rojer" Ryabkov, Tim Chu. Jonathan Zhang has posted comments on this change. ( https://review.coreboot.org/c/flashrom/+/54965 ) Change subject: Add support for Intel Emmitsburg PCH ...................................................................... Patch Set 2: (1 comment) Patchset: PS2: Johnny/Tim, please try this out on Craterlake/S9S. -- To view, visit https://review.coreboot.org/c/flashrom/+/54965 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I2a1bb7467e693d1583aa885fa0e277075edd4a3e Gerrit-Change-Number: 54965 Gerrit-PatchSet: 2 Gerrit-Owner: Jonathan Zhang <jonzhang(a)fb.com> Gerrit-Reviewer: Arthur Heymans <arthur.heymans(a)9elements.com> Gerrit-Reviewer: Christian Walter <christian.walter(a)9elements.com> Gerrit-Reviewer: David Hendricks Gerrit-Reviewer: Deomid "rojer" Ryabkov <rojer9(a)fb.com> Gerrit-Reviewer: Edward O'Callaghan <quasisec(a)chromium.org> Gerrit-Reviewer: Johnny Lin <Johnny_Lin(a)wiwynn.com> Gerrit-Reviewer: Nico Huber <nico.h(a)gmx.de> Gerrit-Reviewer: Stefan Reinauer <stefan.reinauer(a)coreboot.org> Gerrit-Reviewer: Tim Chu <Tim.Chu(a)quantatw.com> Gerrit-Reviewer: build bot (Jenkins) <no-reply(a)coreboot.org> Gerrit-Attention: Arthur Heymans <arthur.heymans(a)9elements.com> Gerrit-Attention: Johnny Lin <Johnny_Lin(a)wiwynn.com> Gerrit-Attention: David Hendricks Gerrit-Attention: Edward O'Callaghan <quasisec(a)chromium.org> Gerrit-Attention: Deomid "rojer" Ryabkov <rojer9(a)fb.com> Gerrit-Attention: Tim Chu <Tim.Chu(a)quantatw.com> Gerrit-Comment-Date: Tue, 31 Aug 2021 17:17:30 +0000 Gerrit-HasComments: Yes Gerrit-Has-Labels: No Gerrit-MessageType: comment

1 0

Change in flashrom[master]: Add support for Intel Emmitsburg PCH
by Christian Walter (Code Review) 31 Aug '21

31 Aug '21

Attention is currently required from: Arthur Heymans, Jonathan Zhang, Johnny Lin, David Hendricks, Edward O'Callaghan, Deomid "rojer" Ryabkov, Tim Chu. Christian Walter has posted comments on this change. ( https://review.coreboot.org/c/flashrom/+/54965 ) Change subject: Add support for Intel Emmitsburg PCH ...................................................................... Patch Set 2: Code-Review+2 -- To view, visit https://review.coreboot.org/c/flashrom/+/54965 To unsubscribe, or for help writing mail filters, visit https://review.coreboot.org/settings Gerrit-Project: flashrom Gerrit-Branch: master Gerrit-Change-Id: I2a1bb7467e693d1583aa885fa0e277075edd4a3e Gerrit-Change-Number: 54965 Gerrit-PatchSet: 2 Gerrit-Owner: Jonathan Zhang <jonzhang(a)fb.com> Gerrit-Reviewer: Arthur Heymans <arthur.heymans(a)9elements.com> Gerrit-Reviewer: Christian Walter <christian.walter(a)9elements.com> Gerrit-Reviewer: David Hendricks Gerrit-Reviewer: Deomid "rojer" Ryabkov <rojer9(a)fb.com> Gerrit-Reviewer: Edward O'Callaghan <quasisec(a)chromium.org> Gerrit-Reviewer: Johnny Lin <Johnny_Lin(a)wiwynn.com> Gerrit-Reviewer: Nico Huber <nico.h(a)gmx.de> Gerrit-Reviewer: Stefan Reinauer <stefan.reinauer(a)coreboot.org> Gerrit-Reviewer: Tim Chu <Tim.Chu(a)quantatw.com> Gerrit-Reviewer: build bot (Jenkins) <no-reply(a)coreboot.org> Gerrit-Attention: Arthur Heymans <arthur.heymans(a)9elements.com> Gerrit-Attention: Jonathan Zhang <jonzhang(a)fb.com> Gerrit-Attention: Johnny Lin <Johnny_Lin(a)wiwynn.com> Gerrit-Attention: David Hendricks Gerrit-Attention: Edward O'Callaghan <quasisec(a)chromium.org> Gerrit-Attention: Deomid "rojer" Ryabkov <rojer9(a)fb.com> Gerrit-Attention: Tim Chu <Tim.Chu(a)quantatw.com> Gerrit-Comment-Date: Tue, 31 Aug 2021 07:23:48 +0000 Gerrit-HasComments: No Gerrit-Has-Labels: Yes Gerrit-MessageType: comment

1 0

2024

2023

2022

2021

2020

2019

2018

2017

flashrom-gerrit August 2021