flashrom September 2010

flashrom@flashrom.org

68 participants
216 discussions

[PATCH] ICH SPI address window for reads
by Carl-Daniel Hailfinger 15 Sep '10

15 Sep '10

ICH SPI has the ability to restrict SPI read/write accesses to a given address range. The low end of the range is configurable by the BIOS (and by flashrom if the BIOS didn't lock down the flash interface), the high end of the range is 0xffffff (2^24-1). This patch checks for an address range restriction and uses the low end of the allowed range as base for SPI reads. A similar workaround for REMS/RES opcodes has been committed in r500. This fixes read on the Intel D945GCLF mainboard where the stock BIOS enforces a restricted address range. Please note that writes need the same fix, but for architectural reasons that fix will be merged once partial write is available. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Index: flashrom-ichspi_read_use_min_addr/spi.c =================================================================== --- flashrom-ichspi_read_use_min_addr/spi.c (Revision 1165) +++ flashrom-ichspi_read_use_min_addr/spi.c (Arbeitskopie) @@ -22,6 +22,7 @@ * Contains the generic SPI framework */ +#include <string.h> #include "flash.h" #include "flashchips.h" #include "chipdrivers.h" @@ -207,6 +208,7 @@ int spi_chip_read(struct flashchip *flash, uint8_t *buf, int start, int len) { + int addrbase = 0; if (!spi_programmer[spi_controller].read) { msg_perr("%s called, but SPI read is unsupported on this " "hardware. Please report a bug at " @@ -214,7 +216,26 @@ return 1; } - return spi_programmer[spi_controller].read(flash, buf, start, len); + /* Check if the chip fits between lowest valid and highest possible + * address. Highest possible address with the current SPI implementation + * means 0xffffff, the highest unsigned 24bit number. + */ + addrbase = spi_get_valid_read_addr(); + if (addrbase + flash->total_size * 1024 > (1 << 24)) { + msg_perr("Flash chip size exceeds the allowed access window. "); + msg_perr("Read will probably fail.\n"); + /* Try to get the best alignment subject to constraints. */ + addrbase = (1 << 24) - flash->total_size * 1024; + } + /* Check if alignment is native (at least the largest power of two which + * is a factor of the mapped size of the chip). + */ + if (ffs(flash->total_size * 1024) > (ffs(addrbase) ? : 33)) { + msg_perr("Flash chip is not aligned natively in the allowed " + "access window.\n"); + msg_perr("Read will probably return garbage.\n"); + } + return spi_programmer[spi_controller].read(flash, buf, addrbase + start, len); } /* -- http://www.hailfinger.org/

2 2

[commit] r1170 - trunk
by repository service 15 Sep '10

15 Sep '10

Author: hailfinger Date: Wed Sep 15 02:13:02 2010 New Revision: 1170 URL: http://flashrom.org/trac/flashrom/changeset/1170 Log: Honor ICH SPI address window for reads. ICH SPI has the ability to restrict SPI read/write accesses to a given address range. The low end of the range is configurable by the BIOS (and by flashrom if the BIOS didn't lock down the flash interface), the high end of the range is 0xffffff (2^24-1). This patch checks for an address range restriction and uses the low end of the allowed range as base for SPI reads. A similar workaround for REMS/RES opcodes has been committed in r500. This fixes read on the Intel D945GCLF mainboard where the stock BIOS enforces a restricted address range. Please note that writes need the same fix, but for architectural reasons that fix will be merged once partial write is available. Signed-off-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Tested by David Hendricks on the Intel D945GCLF mainboard, results at http://paste.flashrom.org/view.php?id=79 Acked-by: David Hendricks <dhendrix(a)google.com> Modified: trunk/spi.c Modified: trunk/spi.c ============================================================================== --- trunk/spi.c Wed Sep 15 02:03:53 2010 (r1169) +++ trunk/spi.c Wed Sep 15 02:13:02 2010 (r1170) @@ -22,6 +22,7 @@ * Contains the generic SPI framework */ +#include <string.h> #include "flash.h" #include "flashchips.h" #include "chipdrivers.h" @@ -207,6 +208,7 @@ int spi_chip_read(struct flashchip *flash, uint8_t *buf, int start, int len) { + int addrbase = 0; if (!spi_programmer[spi_controller].read) { msg_perr("%s called, but SPI read is unsupported on this " "hardware. Please report a bug at " @@ -214,7 +216,26 @@ return 1; } - return spi_programmer[spi_controller].read(flash, buf, start, len); + /* Check if the chip fits between lowest valid and highest possible + * address. Highest possible address with the current SPI implementation + * means 0xffffff, the highest unsigned 24bit number. + */ + addrbase = spi_get_valid_read_addr(); + if (addrbase + flash->total_size * 1024 > (1 << 24)) { + msg_perr("Flash chip size exceeds the allowed access window. "); + msg_perr("Read will probably fail.\n"); + /* Try to get the best alignment subject to constraints. */ + addrbase = (1 << 24) - flash->total_size * 1024; + } + /* Check if alignment is native (at least the largest power of two which + * is a factor of the mapped size of the chip). + */ + if (ffs(flash->total_size * 1024) > (ffs(addrbase) ? : 33)) { + msg_perr("Flash chip is not aligned natively in the allowed " + "access window.\n"); + msg_perr("Read will probably return garbage.\n"); + } + return spi_programmer[spi_controller].read(flash, buf, addrbase + start, len); } /*

1 0

[commit] r1169 - trunk
by repository service 15 Sep '10

15 Sep '10

Author: uwe Date: Wed Sep 15 02:03:53 2010 New Revision: 1169 URL: http://flashrom.org/trac/flashrom/changeset/1169 Log: Add missing GIGABYTE GA-7DXR entry, should have been in r1166. Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/print.c Modified: trunk/print.c ============================================================================== --- trunk/print.c Wed Sep 15 01:56:56 2010 (r1168) +++ trunk/print.c Wed Sep 15 02:03:53 2010 (r1169) @@ -412,6 +412,7 @@ B("GIGABYTE", "GA-6ZMA", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1541", NULL), B("GIGABYTE", "GA-MA785GMT-UD2H", 1, "http://www.gigabyte.de/Products/Motherboard/Products_Overview.aspx?ProductI…", NULL), B("GIGABYTE", "GA-770TA-UD3", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=3272#ov", NULL), + B("GIGABYTE", "GA-7DXR", 1, "http://www.gigabyte.de/Products/Motherboard/Products_Spec.aspx?ProductID=13…", NULL), B("GIGABYTE", "GA-7VT600", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1666", NULL), B("GIGABYTE", "GA-7ZM", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1366", "Works fine if you remove jumper JP9 on the board and disable the flash protection BIOS option."), B("GIGABYTE", "GA-8IRML", 1, "http://www.gigabyte.com/products/product-page.aspx?pid=1343", NULL),

1 0

[PATCH] Winbond chip id fix-up (ver 4)
by Mattias Mattsson 15 Sep '10

15 Sep '10

Same as version 3, but do not rearrange order of chip definitions in flashchips.c for easier review. List all chip variants in the .name strings in flashchips.c Also have two identical entries for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012 with different probe functions in flashchips.c as sometimes (for newer revisions of these chips?) the standard jedec probe seems to work. Eg see test report here: http://patchwork.coreboot.org/patch/1476/ Rename constants W_nnnn -> WINBOND_Wnnnn W_25nnn -> WINBOND_NEX_W25nnn Kill incorrect ASD chip and vendor id. Group Winbond SPI and Parallell chips separately (they have different vendor ids). Change constant names to the "canonical" chip name for the following ids: W_29C020C (0x45) -> WINBOND_W29C020 (Same as W29C020C, W29C022 and ASD AE29F2008) W_29C040P (0x46) -> WINBOND_W29C040 ("P" is for package type [32-pin PLCC], irrelevant) W_29C011 + W_29EE011 (0xC1) -> WINBOND_W29C010M (Same as W29C011A, W29EE011, W29EE012, and ASD AE29F1008) Also add ids for the following Winbond chips: W25Q40 W25Q128 W19B160BB W19B160BT W19B320SB/W19L320SB W19B320ST/W19L320ST W19B322MB W19B322MT W19B323MB W19B323MT W19B324MB W19B324MT W29C512A/W29EE512 W39L010 W39L040A W39L512 W49F002/W49F002B Signed-off-by: Mattias Mattsson <vitplister(a)gmail.com>

2 3

[commit] r1168 - trunk
by repository service 15 Sep '10

15 Sep '10

Author: mhm Date: Wed Sep 15 01:56:56 2010 New Revision: 1168 URL: http://flashrom.org/trac/flashrom/changeset/1168 Log: Rename constants W_nnnn -> WINBOND_Wnnnn W_25nnn -> WINBOND_NEX_W25nnn Kill incorrect ASD chip and vendor id. Group Winbond SPI and parallel chips separately (they have different vendor IDs). Change constant names to the "canonical" chip name for the following ids: W_29C020C (0x45) -> WINBOND_W29C020 (Same as W29C020C, W29C022 and ASD AE29F2008) W_29C040P (0x46) -> WINBOND_W29C040 ("P" is for package type [32-pin PLCC], irrelevant) W_29C011 + W_29EE011 (0xC1) -> WINBOND_W29C010 (Same as W29C010M, W29C011A, W29EE011, W29EE012, and ASD AE29F1008) List all chip variants in the .name strings in flashchips.c Have two identical entries for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012 but with different probe functions in flashchips.c as sometimes (for newer revisions of these chips?) the standard jedec probe seems to work. E.g. see test report here: http://patchwork.coreboot.org/patch/1476/ Also add ids for the following Winbond chips: W25Q40 W25Q128 W19B160BB W19B160BT W19B320SB/W19L320SB W19B320ST/W19L320ST W19B322MB W19B322MT W19B323MB W19B323MT W19B324MB W19B324MT W29C512A/W29EE512 W39L010 W39L040A W39L512 W49F002/W49F002B Signed-off-by: Mattias Mattsson <vitplister(a)gmail.com> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/flashchips.c trunk/flashchips.h Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Wed Sep 15 01:20:35 2010 (r1167) +++ trunk/flashchips.c Wed Sep 15 01:56:56 2010 (r1168) @@ -1003,37 +1003,6 @@ }, { - .vendor = "ASD", - .name = "AE49F2008", - .bustype = CHIP_BUSTYPE_PARALLEL, - .manufacture_id = ASD_ID, - .model_id = ASD_AE49F2008, - .total_size = 256, - .page_size = 128, - .feature_bits = FEATURE_EITHER_RESET, - .tested = TEST_UNTESTED, - .probe = probe_jedec, - .probe_timing = TIMING_FIXME, - .block_erasers = - { - { - .eraseblocks = { - {128 * 1024, 1}, - {96 * 1024, 1}, - {8 * 1024, 2}, - {16 * 1024, 1}, - }, - .block_erase = erase_sector_jedec, - }, { - .eraseblocks = { {256 * 1024, 1} }, - .block_erase = erase_chip_block_jedec, - } - }, - .write = write_jedec, - .read = read_memmapped, - }, - - { .vendor = "Atmel", .name = "AT25DF021", .bustype = CHIP_BUSTYPE_SPI, @@ -6957,7 +6926,7 @@ .name = "W25Q80", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25Q80, + .model_id = WINBOND_NEX_W25Q80, .total_size = 1024, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -6993,7 +6962,7 @@ .name = "W25Q16", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25Q16, + .model_id = WINBOND_NEX_W25Q16, .total_size = 2048, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7029,7 +6998,7 @@ .name = "W25Q32", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25Q32, + .model_id = WINBOND_NEX_W25Q32, .total_size = 4096, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7065,7 +7034,7 @@ .name = "W25Q64", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25Q64, + .model_id = WINBOND_NEX_W25Q64, .total_size = 8192, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7101,7 +7070,7 @@ .name = "W25x10", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25X10, + .model_id = WINBOND_NEX_W25X10, .total_size = 128, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7131,7 +7100,7 @@ .name = "W25x20", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25X20, + .model_id = WINBOND_NEX_W25X20, .total_size = 256, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7161,7 +7130,7 @@ .name = "W25x40", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25X40, + .model_id = WINBOND_NEX_W25X40, .total_size = 512, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7191,7 +7160,7 @@ .name = "W25x80", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25X80, + .model_id = WINBOND_NEX_W25X80, .total_size = 1024, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7221,7 +7190,7 @@ .name = "W25x16", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25X16, + .model_id = WINBOND_NEX_W25X16, .total_size = 2048, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7257,7 +7226,7 @@ .name = "W25x32", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25X32, + .model_id = WINBOND_NEX_W25X32, .total_size = 4096, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7293,7 +7262,7 @@ .name = "W25x64", .bustype = CHIP_BUSTYPE_SPI, .manufacture_id = WINBOND_NEX_ID, - .model_id = W_25X64, + .model_id = WINBOND_NEX_W25X64, .total_size = 8192, .page_size = 256, .feature_bits = FEATURE_WRSR_WREN, @@ -7326,10 +7295,10 @@ { .vendor = "Winbond", - .name = "W29C011", + .name = "W29C010(M)/W29C011A/W29EE011/W29EE012", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = WINBOND_ID, - .model_id = W_29C011, + .model_id = WINBOND_W29C010, .total_size = 128, .page_size = 128, .feature_bits = FEATURE_LONG_RESET, @@ -7349,10 +7318,10 @@ { .vendor = "Winbond", - .name = "W29C020C", + .name = "W29C020(C)/W29C022", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = WINBOND_ID, - .model_id = W_29C020C, + .model_id = WINBOND_W29C020, .total_size = 256, .page_size = 128, .feature_bits = FEATURE_LONG_RESET, @@ -7372,10 +7341,10 @@ { .vendor = "Winbond", - .name = "W29C040P", + .name = "W29C040/P", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = WINBOND_ID, - .model_id = W_29C040P, + .model_id = WINBOND_W29C040, .total_size = 512, .page_size = 256, .feature_bits = FEATURE_LONG_RESET, @@ -7395,10 +7364,10 @@ { .vendor = "Winbond", - .name = "W29EE011", + .name = "W29C010(M)/W29C011A/W29EE011/W29EE012", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = WINBOND_ID, - .model_id = W_29C011, + .model_id = WINBOND_W29C010, .total_size = 128, .page_size = 128, .feature_bits = FEATURE_LONG_RESET, @@ -7421,7 +7390,7 @@ .name = "W39V040A", .bustype = CHIP_BUSTYPE_LPC, .manufacture_id = WINBOND_ID, - .model_id = W_39V040A, + .model_id = WINBOND_W39V040A, .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_EITHER_RESET, @@ -7444,10 +7413,10 @@ { .vendor = "Winbond", - .name = "W39V040B", + .name = "W39V040(F)B", .bustype = CHIP_BUSTYPE_LPC, .manufacture_id = WINBOND_ID, - .model_id = W_39V040B, + .model_id = WINBOND_W39V040B, .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_EITHER_RESET, @@ -7470,10 +7439,10 @@ { .vendor = "Winbond", - .name = "W39V040C", + .name = "W39V040(F)C", .bustype = CHIP_BUSTYPE_LPC, .manufacture_id = WINBOND_ID, - .model_id = W_39V040C, + .model_id = WINBOND_W39V040C, .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_EITHER_RESET, @@ -7500,7 +7469,7 @@ .name = "W39V040FA", .bustype = CHIP_BUSTYPE_FWH, .manufacture_id = WINBOND_ID, - .model_id = W_39V040FA, + .model_id = WINBOND_W39V040FA, .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET, @@ -7531,7 +7500,7 @@ .name = "W39V080A", .bustype = CHIP_BUSTYPE_LPC, .manufacture_id = WINBOND_ID, - .model_id = W_39V080A, + .model_id = WINBOND_W39V080A, .total_size = 1024, .page_size = 64 * 1024, .feature_bits = FEATURE_EITHER_RESET, @@ -7554,10 +7523,10 @@ { .vendor = "Winbond", - .name = "W49F002U", + .name = "W49F002U/N", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = WINBOND_ID, - .model_id = W_49F002U, + .model_id = WINBOND_W49F002U, .total_size = 256, .page_size = 128, .feature_bits = FEATURE_EITHER_RESET, @@ -7588,7 +7557,7 @@ .name = "W49F020", .bustype = CHIP_BUSTYPE_PARALLEL, .manufacture_id = WINBOND_ID, - .model_id = W_49F020, + .model_id = WINBOND_W49F020, .total_size = 256, .page_size = 128, .feature_bits = FEATURE_EITHER_RESET, @@ -7611,7 +7580,7 @@ .name = "W49V002A", .bustype = CHIP_BUSTYPE_LPC, .manufacture_id = WINBOND_ID, - .model_id = W_49V002A, + .model_id = WINBOND_W49V002A, .total_size = 256, .page_size = 128, .feature_bits = FEATURE_EITHER_RESET, @@ -7642,7 +7611,7 @@ .name = "W49V002FA", .bustype = CHIP_BUSTYPE_FWH, .manufacture_id = WINBOND_ID, - .model_id = W_49V002FA, + .model_id = WINBOND_W49V002FA, .total_size = 256, .page_size = 128, .feature_bits = FEATURE_EITHER_RESET, @@ -7673,7 +7642,7 @@ .name = "W39V080FA", .bustype = CHIP_BUSTYPE_FWH, .manufacture_id = WINBOND_ID, - .model_id = W_39V080FA, + .model_id = WINBOND_W39V080FA, .total_size = 1024, .page_size = 64 * 1024, .feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET, @@ -7700,7 +7669,7 @@ .name = "W39V080FA (dual mode)", .bustype = CHIP_BUSTYPE_FWH, .manufacture_id = WINBOND_ID, - .model_id = W_39V080FA_DM, + .model_id = WINBOND_W39V080FA_DM, .total_size = 512, .page_size = 64 * 1024, .feature_bits = FEATURE_REGISTERMAP | FEATURE_EITHER_RESET, Modified: trunk/flashchips.h ============================================================================== --- trunk/flashchips.h Wed Sep 15 01:20:35 2010 (r1167) +++ trunk/flashchips.h Wed Sep 15 01:56:56 2010 (r1168) @@ -110,10 +110,6 @@ #define AMIC_A29L040 0x92 #define AMIC_A49LF040A 0x9d -/* This chip vendor/device ID is probably a misinterpreted LHA header. */ -#define ASD_ID 0x25 /* ASD, not listed in JEP106W */ -#define ASD_AE49F2008 0x52 - #define ATMEL_ID 0x1F /* Atmel */ #define AT_25DF021 0x4300 #define AT_25DF041A 0x4401 @@ -543,35 +539,52 @@ * W25X chips are SPI, first byte of device ID is memory type, second * byte of device ID is related to log(bitsize). */ -#define WINBOND_ID 0xDA /* Winbond */ #define WINBOND_NEX_ID 0xEF /* Winbond (ex Nexcom) serial flashes */ -#define W_25X10 0x3011 -#define W_25X20 0x3012 -#define W_25X40 0x3013 -#define W_25X80 0x3014 -#define W_25X16 0x3015 -#define W_25X32 0x3016 -#define W_25X64 0x3017 -#define W_25Q80 0x4014 -#define W_25Q16 0x4015 -#define W_25Q32 0x4016 -#define W_25Q64 0x4017 -#define W_29C011 0xC1 -#define W_29C020C 0x45 /* Same as W29C020 and ASD AE29F2008 */ -#define W_29C040P 0x46 /* Same as W29C040 */ -#define W_29EE011 0xC1 -#define W_39L020 0xB5 -#define W_39L040 0xB6 -#define W_39V040FA 0x34 -#define W_39V040A 0x3D -#define W_39V040B 0x54 -#define W_39V040C 0x50 -#define W_39V080A 0xD0 -#define W_39V080FA 0xD3 -#define W_39V080FA_DM 0x93 -#define W_49F002U 0x0B -#define W_49F020 0x8C -#define W_49V002A 0xB0 -#define W_49V002FA 0x32 +#define WINBOND_NEX_W25X10 0x3011 +#define WINBOND_NEX_W25X20 0x3012 +#define WINBOND_NEX_W25X40 0x3013 +#define WINBOND_NEX_W25X80 0x3014 +#define WINBOND_NEX_W25X16 0x3015 +#define WINBOND_NEX_W25X32 0x3016 +#define WINBOND_NEX_W25X64 0x3017 +#define WINBOND_NEX_W25Q40 0x4013 +#define WINBOND_NEX_W25Q80 0x4014 +#define WINBOND_NEX_W25Q16 0x4015 +#define WINBOND_NEX_W25Q32 0x4016 +#define WINBOND_NEX_W25Q64 0x4017 +#define WINBOND_NEX_W25Q128 0x4018 + +#define WINBOND_ID 0xDA /* Winbond */ +#define WINBOND_W19B160BB 0x49 +#define WINBOND_W19B160BT 0xC4 +#define WINBOND_W19B320SB 0x2A /* Same as W19L320SB */ +#define WINBOND_W19B320ST 0xBA /* Same as W19L320ST */ +#define WINBOND_W19B322MB 0x92 +#define WINBOND_W19B322MT 0x10 +#define WINBOND_W19B323MB 0x94 +#define WINBOND_W19B323MT 0x13 +#define WINBOND_W19B324MB 0x97 +#define WINBOND_W19B324MT 0x16 +#define WINBOND_W29C010 0xC1 /* Same as W29C010M, W29C011A, W29EE011, W29EE012, and ASD AE29F1008 */ +#define WINBOND_W29C020 0x45 /* Same as W29C020C, W29C022 and ASD AE29F2008 */ +#define WINBOND_W29C040 0x46 /* Same as W29C040P */ +#define WINBOND_W29C512A 0xC8 /* Same as W29EE512 */ +#define WINBOND_W39L010 0x31 +#define WINBOND_W39L020 0xB5 +#define WINBOND_W39L040 0xB6 +#define WINBOND_W39L040A 0xD6 +#define WINBOND_W39L512 0x38 +#define WINBOND_W39V040A 0x3D +#define WINBOND_W39V040FA 0x34 +#define WINBOND_W39V040B 0x54 /* Same as W39V040FB */ +#define WINBOND_W39V040C 0x50 /* Same as W39V040FC */ +#define WINBOND_W39V080A 0xD0 +#define WINBOND_W39V080FA 0xD3 +#define WINBOND_W39V080FA_DM 0x93 /* W39V080FA dual mode */ +#define WINBOND_W49F002 0x25 /* Same as W49F002B */ +#define WINBOND_W49F002U 0x0B /* Same as W49F002N and ASD AE49F2008 */ +#define WINBOND_W49F020 0x8C +#define WINBOND_W49V002A 0xB0 +#define WINBOND_W49V002FA 0x32 #endif /* !FLASHCHIPS_H */

1 0

[commit] r1167 - trunk
by repository service 15 Sep '10

15 Sep '10

Author: uwe Date: Wed Sep 15 01:20:35 2010 New Revision: 1167 URL: http://flashrom.org/trac/flashrom/changeset/1167 Log: Board-enable for the ASUS A7V333. The board-enable is the same as for the ASUS A7V8X, i.e., it raises GP51 on the ITE IT8703F. I verified using a multimeter that this will raise both, WE# and TBL# on the flash chip. All operations successfully tested on hardware. Also renamed board_asus_a7v8x() to it8703f_gpio51_raise(). Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Joshua Roys <roysjosh(a)gmail.com> Modified: trunk/board_enable.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Wed Sep 15 00:59:39 2010 (r1166) +++ trunk/board_enable.c Wed Sep 15 01:20:35 2010 (r1167) @@ -1689,9 +1689,10 @@ /* * Suited for: + * - ASUS A7V333: VIA KT333 + VT8233A + IT8703F * - ASUS A7V8X: VIA KT400 + VT8235 + IT8703F */ -static int board_asus_a7v8x(void) +static int it8703f_gpio51_raise(void) { uint16_t id, base; uint8_t tmp; @@ -1855,7 +1856,8 @@ {0x8086, 0x2570, 0x1849, 0x2570, 0x8086, 0x24d3, 0x1849, 0x24d0, NULL, NULL, NULL, "ASRock", "775i65G", 0, OK, intel_ich_gpio23_raise}, {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3065, 0x1043, 0x80ED, NULL, NULL, NULL, "ASUS", "A7V600-X", 0, OK, it8712f_gpio3_1_raise}, {0x1106, 0x3177, 0x1043, 0x80A1, 0x1106, 0x3205, 0x1043, 0x8118, NULL, NULL, NULL, "ASUS", "A7V8X-MX SE", 0, OK, w836xx_memw_enable_2e}, - {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x808C, NULL, NULL, NULL, "ASUS", "A7V8X", 0, OK, board_asus_a7v8x}, + {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x808C, NULL, NULL, NULL, "ASUS", "A7V8X", 0, OK, it8703f_gpio51_raise}, + {0x1106, 0x3099, 0x1043, 0x807F, 0x1106, 0x3147, 0x1043, 0x808C, NULL, NULL, NULL, "ASUS", "A7V333", 0, OK, it8703f_gpio51_raise}, {0x1106, 0x3189, 0x1043, 0x807F, 0x1106, 0x3177, 0x1043, 0x80A1, NULL, NULL, NULL, "ASUS", "A7V8X-X", 0, OK, it8712f_gpio3_1_raise}, {0x8086, 0x27A0, 0x1043, 0x1287, 0x8086, 0x27DF, 0x1043, 0x1287, "^A8J", NULL, NULL, "ASUS", "A8Jm", 0, NT, intel_ich_gpio34_raise}, {0x10DE, 0x0260, 0x103c, 0x2a3e, 0x10DE, 0x0264, 0x103c, 0x2a3e, "NAGAMI2L", NULL, NULL, "ASUS", "A8N-LA (Nagami-GL8E)", 0, OK, nvidia_mcp_gpio0_raise}, Modified: trunk/print.c ============================================================================== --- trunk/print.c Wed Sep 15 00:59:39 2010 (r1166) +++ trunk/print.c Wed Sep 15 01:20:35 2010 (r1167) @@ -314,6 +314,7 @@ B("ASUS", "A7N8X Deluxe", 1, "http://www.asus.com/product.aspx?P_ID=wAsRYm41KTp78MFC", NULL), B("ASUS", "A7N8X-E Deluxe", 1, "http://www.asus.com/product.aspx?P_ID=TmQtPJv4jIxmL9C2", NULL), B("ASUS", "A7V133", 1, "ftp://ftp.asus.com.tw/pub/ASUS/mb/socka/kt133a/a7v133/", NULL), + B("ASUS", "A7V333", 1, "ftp://ftp.asus.com.tw/pub/asus/mb/socka/kt333/a7v333/", NULL), B("ASUS", "A7V400-MX", 1, "http://www.asus.com/product.aspx?P_ID=hORgEHRBDLMfwAwx", NULL), B("ASUS", "A7V600-X", 1, "http://www.asus.com/product.aspx?P_ID=L2XYS0rmtCjeOr4k", NULL), B("ASUS", "A7V8X", 1, "http://www.asus.com/product.aspx?P_ID=qfpaGrAy2kLVo0f2", NULL),

1 0

[PATCH] ASUS A7V333 board-enable
by Uwe Hermann 15 Sep '10

15 Sep '10

See patch. Maybe we should rename board_asus_a7v8x() to it8703f_raise_gp51() or the like, though. lspci, superiotool, or flashrom -w logs attached. Uwe. -- http://hermann-uwe.de | http://sigrok.org http://randomprojects.org | http://unmaintained-free-software.org

2 2

Re: [flashrom] ST M25PX32 and M25PX64 flash chip support
by Uwe Hermann 15 Sep '10

15 Sep '10

On Tue, Sep 14, 2010 at 03:45:03PM +0000, Jason Shriver wrote: > Yes, subsector erase is supported by these flash chips. Thank you for adding that capability to the block_erasers list. > > This change was tested on the Intel greencity and Intel foxhollow customer reference boards. These are Intel reference design boards not commercial motherboards. Thanks, both marked as tested now. I wasn't able to find a "canonical" page at intel.com with some info about the boards, please let us know if such a (public) page exists. Uwe. -- http://hermann-uwe.de | http://sigrok.org http://randomprojects.org | http://unmaintained-free-software.org

2 1

flashrom result for the AMD 890
by Mark Terranova 15 Sep '10

15 Sep '10

/superiotool$ sudo flashrom -V flashrom v0.9.1-r946 No coreboot table found. DMI string system-manufacturer: "BIOSTAR Group" DMI string system-product-name: "TA890GXB HD" DMI string system-version: " " DMI string baseboard-manufacturer: "BIOSTAR Group" DMI string baseboard-product-name: "TA890GXB HD" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found ITE Super I/O, id 8721 Found chipset "AMD SB700/SB710/SB750", enabling flash write... SPI base address is at 0xfec10000 AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 SpiArbEnable=1, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, ArbWaitCount=7, SpiBridgeDisable=1, DropOneClkOnRd=0 GPIO11 used for SPI_DO GPIO12 used for SPI_DI GPIO31 used for SPI_HOLD GPIO32 used for SPI_CS GPIO47 used for SPI_CLK ROM strap override is not active OK. This chipset supports the following protocols: LPC,FWH,SPI. Calibrating delay loop... 827M loops per second, 100 myus = 201 us. OK. Probing for AMD Am29F010A/B, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F016D, 2048 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F040B, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29F080B, 1024 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV040B, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMD Am29LV081B, 1024 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ASD AE49F2008, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT25DF021, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT29C512, 64 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C010A, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C020, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT29C040A, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT45CS1282, 16896 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT49BV512, 64 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N), 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A25L40PT, 512 KB: RDID returned 0xc2 0x20 0x14 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 KB: RDID returned 0xc2 0x20 0x14 0xc2. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A29002B, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29002T, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A29040B, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for EMST F49B002UA, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Eon EN25B05, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25D16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN29F010, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)B, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for EON EN29F002(A)(N)T, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-B, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F001BX-T, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 28F004S5, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x1f, id2 0xa0 Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for Macronix MX25L512, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 00 Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX29F001B, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F001T, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002B, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29F002T, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Macronix MX29LV040, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Numonyx M25PE10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm29F002T, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm29F002B, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm39LV010, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0x49, id2 0xa3, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for Spansion S25FL008A, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF016B, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 KB: REMS returned c2 13. probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040B.REMS, 512 KB: REMS returned c2 13. probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST28SF040A, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE010, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE010, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29EE020A, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST29LE020, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF512, 64 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF010A, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF020A, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39SF040, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF512, 64 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF010, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF020, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF040, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST39VF080, 1024 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0x49, id2 0xa3, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x7b, id2 0x85, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x1f, id2 0xa0 Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0x49, id2 0xa3, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0x49, id2 0xa3, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for ST M25P05-A, 64 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 KB: RDID returned 0xc2 0x20 0x14. Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 KB: RDID returned 0xc2 0x20 0x14. Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 KB: RDID returned 0xc2 0x20 0x14. Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M29F002B, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F002T/NT, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F040B, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29F400BT, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W010B, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W040B, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M29W512B, 64 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x1f, id2 0xa0 Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x1f, id2 0xa0 Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0x49, id2 0xa3 Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x1f, id2 0xa0 Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0x4d, id2 0x49 Probing for SyncMOS S29C31004T, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51001T, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51002T, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for SyncMOS S29C51004T, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RB, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for TI TMS29F002RT, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W25x10, 128 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x20, 256 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x40, 512 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x80, 1024 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x16, 2048 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x32, 4096 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x64, 8192 KB: RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W29C011, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C020C, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29C040P, 512 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W29EE011, 128 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: skipped. Host bus type LPC,FWH,SPI and chip bus type Parallel are incompatible. Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0x49, id2 0xa3, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0x49, id2 0xa3, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x4d, id2 0x49, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x1f, id2 0xa0, id1 is normal flash content, id2 is normal flash content Probing for Atmel unknown Atmel SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for EON unknown EON SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Macronix unknown Macronix SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for PMC unknown PMC SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for SST unknown SST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for ST unknown ST SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Sanyo unknown Sanyo SPI chip, 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Generic unknown SPI chip (RDID), 0 KB: Not mapping flash chip, zero size at 0x00000000. RDID returned 0xc2 0x20 0x14. probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Not unmapping zero size at (nil) Probing for Generic unknown SPI chip (REMS), 0 KB: Not mapping flash chip, zero size at 0x00000000. REMS returned c2 13. probe_spi_rems: id1 0xc2, id2 0x13 Not unmapping zero size at (nil) === This flash part has status UNTESTED for operations: ERASE Please email a report to flashrom(a)flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -rV, -wV, -EV), and mention which mainboard or programmer you tested. Thanks for your help! ===

3 2

[commit] r1166 - trunk
by repository service 15 Sep '10

15 Sep '10

Author: uwe Date: Wed Sep 15 00:59:39 2010 New Revision: 1166 URL: http://flashrom.org/trac/flashrom/changeset/1166 Log: Another round of board/chip status updates. Mark the following boards as tested: - Intel Foxhollow (reported by Jason Shriver <J.Shriver(a)F5.com>) http://www.flashrom.org/pipermail/flashrom/2010-September/004768.html - Intel Greencity (reported by Jason Shriver <J.Shriver(a)F5.com>) http://www.flashrom.org/pipermail/flashrom/2010-September/004768.html - Tyan S2915-E (Thunder n6650W) (reported by Axel Bergerhoff <axelbergerhoff(a)compuserve.com>) http://www.flashrom.org/pipermail/flashrom/2010-August/004560.html - ASUS Z8NA-D6C (reported by John Wells <jb(a)sourceillustrated.com>) http://www.flashrom.org/pipermail/flashrom/2010-September/004737.html - GIGABYTE GA-7DXR (reported by Uwe Hermann <uwe(a)hermann-uwe.de>) http://www.flashrom.org/pipermail/flashrom/2010-September/004712.html - MSI MS-7211 (PM8M3-V) (reported by Shahar Or <mightyiampresence(a)gmail.com>) http://www.flashrom.org/pipermail/flashrom/2010-September/004612.html - MSI MS-6787 (P4MAM-V/P4MAM-L) (reported by Swift Geek <swiftgeek(a)gmail.com>) Board-enable now marked as tested. http://www.flashrom.org/pipermail/flashrom/2010-September/004687.html Chips: - SST SST25VF016B (reported by Warren Turkal <wt(a)penguintechs.org>) http://www.flashrom.org/pipermail/flashrom/2010-September/004716.html Signed-off-by: Uwe Hermann <uwe(a)hermann-uwe.de> Acked-by: Uwe Hermann <uwe(a)hermann-uwe.de> Modified: trunk/board_enable.c trunk/flashchips.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Tue Sep 14 15:16:01 2010 (r1165) +++ trunk/board_enable.c Wed Sep 15 00:59:39 2010 (r1166) @@ -1908,7 +1908,7 @@ {0x13f6, 0x0111, 0x1462, 0x5900, 0x1106, 0x3177, 0x1106, 0, NULL, NULL, NULL, "MSI", "MS-6590 (KT4 Ultra)", 0, OK, board_msi_kt4v}, {0x1106, 0x3149, 0x1462, 0x7094, 0x10ec, 0x8167, 0x1462, 0x094c, NULL, NULL, NULL, "MSI", "MS-6702E (K8T Neo2-F)", 0, OK, w83627thf_gpio44_raise_2e}, {0x1106, 0x0571, 0x1462, 0x7120, 0x1106, 0x3065, 0x1462, 0x7120, NULL, NULL, NULL, "MSI", "MS-6712 (KT4V)", 0, OK, board_msi_kt4v}, - {0x1106, 0x3148, 0 , 0 , 0x1106, 0x3177, 0 , 0 , NULL, "msi", "ms6787", "MSI", "MS-6787 (P4MAM-V/P4MAM-L)", 0, NT, w836xx_memw_enable_2e}, + {0x1106, 0x3148, 0 , 0 , 0x1106, 0x3177, 0 , 0 , NULL, "msi", "ms6787", "MSI", "MS-6787 (P4MAM-V/P4MAM-L)", 0, OK, w836xx_memw_enable_2e}, {0x1039, 0x7012, 0x1462, 0x0050, 0x1039, 0x6325, 0x1462, 0x0058, NULL, NULL, NULL, "MSI", "MS-7005 (651M-L)", 0, OK, board_msi_651ml}, {0x10DE, 0x00E0, 0x1462, 0x0250, 0x10DE, 0x00E1, 0x1462, 0x0250, NULL, NULL, NULL, "MSI", "MS-7025 (K8N Neo2 Platinum)", 0, OK, nvidia_mcp_gpio0c_raise}, {0x8086, 0x2658, 0x1462, 0x7046, 0x1106, 0x3044, 0x1462, 0x046d, NULL, NULL, NULL, "MSI", "MS-7046", 0, OK, intel_ich_gpio19_raise}, Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Tue Sep 14 15:16:01 2010 (r1165) +++ trunk/flashchips.c Wed Sep 15 00:59:39 2010 (r1166) @@ -4778,7 +4778,7 @@ .model_id = SST_25VF016B, .total_size = 2048, .page_size = 256, - .tested = TEST_OK_PRW, + .tested = TEST_OK_PREW, .probe = probe_spi_rdid, .probe_timing = TIMING_ZERO, .block_erasers = Modified: trunk/print.c ============================================================================== --- trunk/print.c Tue Sep 14 15:16:01 2010 (r1165) +++ trunk/print.c Wed Sep 15 00:59:39 2010 (r1166) @@ -381,6 +381,7 @@ B("ASUS", "P6T SE", 1, "http://www.asus.com/product.aspx?P_ID=t4yhK6y9W9o7iQ9E", NULL), B("ASUS", "P6T Deluxe", 1, "http://www.asus.com/product.aspx?P_ID=vXixf82co6Q5v0BZ", NULL), B("ASUS", "P6T Deluxe V2", 1, "http://www.asus.com/product.aspx?P_ID=iRlP8RG9han6saZx", NULL), + B("ASUS", "Z8NA-D6C", 1, "http://www.asus.com/product.aspx?P_ID=k81cpN8uEB01BpQ6", NULL), B("BCOM", "WinNET100", 1, "http://www.coreboot.org/BCOM_WINNET100", "Used in the IGEL-316 thin client."), B("Biostar", "M6TBA", 0, "ftp://ftp.biostar-usa.com/manuals/M6TBA/", "No public report found. Owned by Uwe Hermann <uwe(a)hermann-uwe.de>. May work now."), B("Biostar", "M7NCD Pro", 1, "http://www.biostar.com.tw/app/en/mb/content.php?S_ID=260", NULL), @@ -440,6 +441,8 @@ B("IEI", "PICOe-9452", 1, "http://www.ieiworld.com/product_groups/industrial/content.aspx?keyword=WSB&…", NULL), B("Intel", "D201GLY", 1, "http://www.intel.com/support/motherboards/desktop/d201gly/index.htm", NULL), B("Intel", "EP80759", 1, NULL, NULL), + B("Intel", "Foxhollow", 1, NULL, "Intel reference board."), + B("Intel", "Greencity", 1, NULL, "Intel reference board."), B("Intel", "SE440BX-2", 0, "http://downloadcenter.intel.com/SearchResult.aspx?lang=eng&ProductFamily=De…", "Probably won't work, see http://www.coreboot.org/pipermail/flashrom/2010-July/003952.html"), B("IWILL", "DK8-HTX", 1, "http://web.archive.org/web/20060507170150/http://www.iwill.net/product_2.as…", NULL), B("Jetway", "J7F4K1G5D-PB", 1, "http://www.jetway.com.tw/jetway/system/productshow2.asp?id=389&proname=J7F4…", NULL), @@ -466,6 +469,7 @@ B("MSI", "MS-7135 (K8N Neo3)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=170", NULL), B("MSI", "MS-7168 (Orion)", 1, "http://support.packardbell.co.uk/uk/item/index.php?i=spec_orion&pi=platform…", NULL), B("MSI", "MS-7207 (K8NGM2-L)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=224", NULL), + B("MSI", "MS-7211 (PM8M3-V)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=234", NULL), B("MSI", "MS-7236 (945PL Neo3)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=1173", NULL), B("MSI", "MS-7253 (K9VGM-V)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=260", NULL), B("MSI", "MS-7255 (P4M890M)", 1, "http://www.msi.com/index.php?func=proddesc&maincat_no=1&prod_no=1082", NULL), @@ -518,6 +522,7 @@ B("Tyan", "S2892 (Thunder K8SE)", 1, "http://www.tyan.com/product_board_detail.aspx?pid=145", NULL), B("Tyan", "S2895 (Thunder K8WE)", 1, "http://www.tyan.com/archive/products/html/thunderk8we.html", NULL), B("Tyan", "S2915 (Thunder n6650W)", 1, "http://tyan.com/product_board_detail.aspx?pid=163", NULL), + B("Tyan", "S2915-E (Thunder n6650W)", 1, "http://tyan.com/product_SKU_spec.aspx?ProductType=MB&pid=541&SKU=600000041", NULL), B("Tyan", "S2933 (Thunder n3600S)", 1, "http://tyan.com/product_SKU_spec.aspx?ProductType=MB&pid=478&SKU=600000063", NULL), B("Tyan", "S3095 (Tomcat i945GM)", 1, "http://www.tyan.com/product_board_detail.aspx?pid=181", NULL), B("Tyan", "S3992 (Thunder h2000M)", 1, "http://tyan.com/product_board_detail.aspx?pid=235", NULL),

1 0

← Newer
1
...
9
10
11
12
13
14
15
...
22
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom September 2010