Anastasia Klimchuk has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/86019?usp=email )
Change subject: doc: Add document for using flashrom with CH341A/B ......................................................................
doc: Add document for using flashrom with CH341A/B
Document is contributed by Stephan Schneider.
Change-Id: Id6848329d88146fc8a005437a76ec52bec986259 Signed-off-by: Anastasia Klimchuk aklm@flashrom.org --- A doc/supported_hw/supported_prog/black_board_with_IC_socket.jpg A doc/supported_hw/supported_prog/blue_board_additional_IC_socket_with_wiring.jpg A doc/supported_hw/supported_prog/blue_board_without_IC_socket.jpg A doc/supported_hw/supported_prog/ch341ab.rst A doc/supported_hw/supported_prog/green_3_3V_orange_5V.jpg M doc/supported_hw/supported_prog/index.rst A doc/supported_hw/supported_prog/pinout_of_EEPROM.jpg A doc/supported_hw/supported_prog/yellow_insulating_tape_pink_new_connections.jpg 8 files changed, 89 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/flashrom refs/changes/19/86019/1
diff --git a/doc/supported_hw/supported_prog/black_board_with_IC_socket.jpg b/doc/supported_hw/supported_prog/black_board_with_IC_socket.jpg new file mode 100644 index 0000000..7c6df3a --- /dev/null +++ b/doc/supported_hw/supported_prog/black_board_with_IC_socket.jpg Binary files differ diff --git a/doc/supported_hw/supported_prog/blue_board_additional_IC_socket_with_wiring.jpg b/doc/supported_hw/supported_prog/blue_board_additional_IC_socket_with_wiring.jpg new file mode 100644 index 0000000..9a578b3 --- /dev/null +++ b/doc/supported_hw/supported_prog/blue_board_additional_IC_socket_with_wiring.jpg Binary files differ diff --git a/doc/supported_hw/supported_prog/blue_board_without_IC_socket.jpg b/doc/supported_hw/supported_prog/blue_board_without_IC_socket.jpg new file mode 100644 index 0000000..43b19db --- /dev/null +++ b/doc/supported_hw/supported_prog/blue_board_without_IC_socket.jpg Binary files differ diff --git a/doc/supported_hw/supported_prog/ch341ab.rst b/doc/supported_hw/supported_prog/ch341ab.rst new file mode 100644 index 0000000..9255989 --- /dev/null +++ b/doc/supported_hw/supported_prog/ch341ab.rst @@ -0,0 +1,88 @@ +========= +CH341A/B +========= + +.. meta:: + :author: Stephan Schneider + +The CH341\ **A** is a chip that provides a bridge between USB and serial communication. The +CH341\ **B** is almost identical, it also has a built-in oscillator. However, it is not +recommended to use the CH341\ **B** with the built-in oscillator and without a crystal +as the accuracy of the built-in oscillator is very poor and timing problems can occur +during data transmission. The serial communication of the CH341A/B can be UART or SPI/I2C, +here we are only interested in the SPI/I2C mode. The following description applies to both +chips, it does not matter which one you have. With a crystal, flashrom works with both the +CH341A and the CH341B without changing the software. + + +There are 2 ready-made boards that are suitable for use with flashrom, one with an IC socket +(Textool) with a mostly black board and one without an IC socket with a mostly blue board. + +Image 1: Black board with IC socket + +.. image:: black_board_with_IC_socket.jpg + +Image 2: Blue board without IC socket + +.. image:: blue_board_without_IC_socket.jpg + +Both boards have advantages and disadvantages. The black board with IC socket is more practical +because the IC socket is already installed. However, it has an error in the circuit diagram that +must be corrected so as not to jeopardize the EEPROMs. There is a voltage converter on the board to +convert the 5 volts of the USB to 3.3 volts, the 3.3 volts are then fed to the IC socket, but +unfortunately the CH341A is still supplied with 5 volts. The CH341A also works with 5 volts, but then +there is a voltage of just under 5 volts at the outputs of the CH341A that lead to the IC socket, +which is usually too much for the inputs of the EEPROMs and can cause them to break. The blue board +without an IC socket is correctly designed, but you also need an IC socket and some connecting wires, +which makes things complicated and error-prone. + +Image 3: Blue board and additional IC socket with wiring + +.. image:: blue_board_additional_IC_socket_with_wiring.jpg + +The conversion of the black circuit board with IC socket is simple: You need a soldering iron, +some insulated wire, some insulating tape and a steady hand. First you need to lift pin 28 of the +CH341A by approx. 1 mm, heat the pin with the soldering iron and insert a thin knife blade between +the pin and the board. Then stick a small piece of insulating tape between the pin and the circuit +board to prevent contact. Then you have to connect the bent up pin 28 with 3.3 volts and pin 9 also +with 3.3 volts, the connections are shown in the next picture. + +Image 4: Yellow: insulating tape, pink: new connections + +.. image:: yellow_insulating_tape_pink_new_connections.jpg + +For programming with flashrom you have to set the SPI/I2C mode of the CH341A, the corresponding jumper +must be set to the position shown in the pictures (it is the yellow jumper in each case). On the blue +board without IC socket you have to set the operating voltage with 2 jumpers (here blue), this is +usually 3.3 volts, there are only a few older EEPROMs that still require 5 volts, please check the data +sheet of the EEPROM to be on the safe side. + +Image 5: Green: 3.3 Volt, orange: 5 Volt + +.. image:: green_3_3V_orange_5V.jpg + +When using the blue board, you still have to make the correct connections between the EEPROM and the CH341A board: + ++---------------+--------------+ +| Pin 1 -> CS0 | Pin 8 -> Vcc | ++---------------+--------------+ +| Pin 2 -> MISO | Pin 7 -> Vcc | ++---------------+--------------+ +| Pin 3 -> Vcc | Pin 6 ➔ SCK | ++---------------+--------------+ +| Pin 4 -> GND | Pin 5 ➔ MOSI | ++---------------+--------------+ + +Pin 1 of the EEPROM is usually marked with a dot or similar, see also the EEPROM data sheet + +Image 6: Pinout of an EEPROM + +.. image:: pinout_of_EEPROM.jpg + +The following commands are some examples how to call flashrom with CH341A:: + + flashrom -p ch341a_spi + flashrom -p ch341a_spi -r filename.bin + flashrom -p ch341a_spi -w filename.bin + +That's all, good luck! diff --git a/doc/supported_hw/supported_prog/green_3_3V_orange_5V.jpg b/doc/supported_hw/supported_prog/green_3_3V_orange_5V.jpg new file mode 100644 index 0000000..6886f6f --- /dev/null +++ b/doc/supported_hw/supported_prog/green_3_3V_orange_5V.jpg Binary files differ diff --git a/doc/supported_hw/supported_prog/index.rst b/doc/supported_hw/supported_prog/index.rst index 7912f34..b87b995 100644 --- a/doc/supported_hw/supported_prog/index.rst +++ b/doc/supported_hw/supported_prog/index.rst @@ -16,6 +16,7 @@ :maxdepth: 1
buspirate + ch341ab dummyflasher ft2232_spi serprog/index diff --git a/doc/supported_hw/supported_prog/pinout_of_EEPROM.jpg b/doc/supported_hw/supported_prog/pinout_of_EEPROM.jpg new file mode 100644 index 0000000..bf17d6f --- /dev/null +++ b/doc/supported_hw/supported_prog/pinout_of_EEPROM.jpg Binary files differ diff --git a/doc/supported_hw/supported_prog/yellow_insulating_tape_pink_new_connections.jpg b/doc/supported_hw/supported_prog/yellow_insulating_tape_pink_new_connections.jpg new file mode 100644 index 0000000..af20705 --- /dev/null +++ b/doc/supported_hw/supported_prog/yellow_insulating_tape_pink_new_connections.jpg Binary files differ
-
Anastasia Klimchuk (Code Review)