[M] Change in flashrom[main]: doc: Convert the doc for MSI JSPI1

[Anastasia Klimchuk (Code Review)]

Anastasia Klimchuk has uploaded this change for review. ( https://review.coreboot.org/c/flashrom/+/83753?usp=email )

Change subject: doc: Convert the doc for MSI JSPI1
......................................................................

doc: Convert the doc for MSI JSPI1

The doc converted from
https://wiki.flashrom.org/MSI_JSPI1

Change-Id: Idd215a3a3a4d62629803a71d360755c43c1ab599
Signed-off-by: Anastasia Klimchuk 
---
M doc/user_docs/index.rst
A doc/user_docs/msi_jspi1.rst
2 files changed, 51 insertions(+), 0 deletions(-)

git pull ssh://review.coreboot.org:29418/flashrom refs/changes/53/83753/1

diff --git a/doc/user_docs/index.rst b/doc/user_docs/index.rst
index b61567a..6756d9e 100644
--- a/doc/user_docs/index.rst
+++ b/doc/user_docs/index.rst
@@ -9,3 +9,4 @@
     chromebooks
     management_engine
     misc_intel
+    msi_jspi1
diff --git a/doc/user_docs/msi_jspi1.rst b/doc/user_docs/msi_jspi1.rst
new file mode 100644
index 0000000..dc20866
--- /dev/null
+++ b/doc/user_docs/msi_jspi1.rst
@@ -0,0 +1,50 @@
+=========
+MSI JSPI1
+=========
+
+JSPI1 is a 5x2 or 6x2 2.0mm pitch pin header on many MSI motherboards.
+It is used to recover from bad boot ROM images. Specifically,
+it appears to be used to connect an alternate ROM with a working image.
+Pull the #HOLD line low to deselect the onboard SPI ROM, allowing another
+SPI ROM to take its place on the bus. Pull the #WP line high to disable write-protection.
+Some boards use 1.8V flash chips, while others use 3.3V flash chips;
+Check the flash chip datasheet to determine the correct value.
+
+**JSPI1 (5x2)**
+
+======== ======== ======== ====
+name     pin      pin      name
+======== ======== ======== ====
+VCC      1        2 	   VCC
+MISO     3        4	   MOSI
+#SS      5        6	   SCLK
+GND      7        8	   GND
+#HOLD    9        10 	   NC
+======== ======== ======== ====
+
+**JSPI1 (6x2)**
+
+======== ======== ======== ============
+name     pin      pin      name
+======== ======== ======== ============
+VCC      1	  2	   VCC
+SO       3        4	   SI
+#SS      5	  6	   CLK
+GND      7        8	   GND
+NC       9        10	   NC (no pin)
+#WP      11       12	   #HOLD
+======== ======== ======== ============
+
+======== =====================================
+name	 function
+======== =====================================
+VCC	 Voltage (See flash chip datasheet)
+MISO	 SPI Master In/Slave Out
+MOSI	 SPI Master Out/Slave In
+#SS	 SPI Slave (Chip) Select (active low)
+SCLK	 SPI Clock
+GND	 ground/common
+#HOLD	 SPI hold (active low)
+#WP	 SPI write-protect (active low)
+NC	 Not Connected (or no pin)
+======== =====================================