Change in flashrom[master]: pickit2_spi.c: Separate shutdown from failed init cleanup

[Nico Huber (Code Review)]

Nico Huber has submitted this change. ( https://review.coreboot.org/c/flashrom/+/52773 )

Change subject: pickit2_spi.c: Separate shutdown from failed init cleanup
......................................................................

pickit2_spi.c: Separate shutdown from failed init cleanup

Shutdown function was covering two different jobs here: 1) the actual
shutdown which is run at the end of the driver's lifecycle and
2) cleanup in cases when initialisation failed. Now, shutdown is only
doing its main job (#1), and the driver itself is doing cleanup
when init fails (#2).

The good thing is that now resources are released/closed immediately
in cases when init fails (vs shutdown function which was run at some
point later), and the driver leaves clean space after itself if init
fails.

And very importantly this unlocks API change which plans to move
register_shutdown inside register master API, see
https://review.coreboot.org/c/flashrom/+/51761

TEST=builds
BUG=b:185191942

Change-Id: I1b672b33169a7a1b6ceab190ad3f48c2f35c3a1f
Signed-off-by: Anastasia Klimchuk 
Reviewed-on: https://review.coreboot.org/c/flashrom/+/52773
Tested-by: build bot (Jenkins) 
Reviewed-by: Nico Huber 
Reviewed-by: Angel Pons 
---
M pickit2_spi.c
1 file changed, 13 insertions(+), 14 deletions(-)

Approvals:
  build bot (Jenkins): Verified
  Nico Huber: Looks good to me, approved
  Angel Pons: Looks good to me, approved

diff --git a/pickit2_spi.c b/pickit2_spi.c
index 0bc17af..367d0fc 100644
--- a/pickit2_spi.c
+++ b/pickit2_spi.c
@@ -458,34 +458,33 @@
    	return 1;
    }

-	if (register_shutdown(pickit2_shutdown, NULL) != 0) {
-		return 1;
-	}
-
-	if (pickit2_get_firmware_version()) {
-		return 1;
-	}
+	if (pickit2_get_firmware_version())
+		goto init_err_cleanup_exit;

/* Command Set SPI Speed */
-	if (pickit2_set_spi_speed(spispeed_idx)) {
-		return 1;
-	}
+	if (pickit2_set_spi_speed(spispeed_idx))
+		goto init_err_cleanup_exit;

/* Command Set SPI Voltage */
    msg_pdbg("Setting voltage to %i mV.\n", millivolt);
-	if (pickit2_set_spi_voltage(millivolt) != 0) {
-		return 1;
-	}
+	if (pickit2_set_spi_voltage(millivolt) != 0)
+		goto init_err_cleanup_exit;

/* Perform basic setup.
     * Configure pin directions and logic levels, turn Vdd on, turn busy LED on and clear buffers. */
    int transferred;
    if (libusb_interrupt_transfer(pickit2_handle, ENDPOINT_OUT, buf, CMD_LENGTH, &transferred, DFLT_TIMEOUT) != 0) {
    	msg_perr("Command Setup failed!\n");
-		return 1;
+		goto init_err_cleanup_exit;
    }

+	if (register_shutdown(pickit2_shutdown, NULL))
+		goto init_err_cleanup_exit;
    register_spi_master(&spi_master_pickit2);

return 0;
+
+init_err_cleanup_exit:
+	pickit2_shutdown(NULL);
+	return 1;
 }