Nico Huber has uploaded this change for review. ( https://review.coreboot.org/23804
Change subject: NVIDIA Tegra2 SPI controller support ......................................................................
NVIDIA Tegra2 SPI controller support
On Tue, Jun 28, 2011 at 5:54 PM, Carl-Daniel Hailfinger < c-d.hailfinger.devel.2006@gmx.net> wrote:
2-3-add_arm_isms.patch
Have you checked with an architecture guru that sync_primitive() can
really be empty, not only for that arch in general, but also for accesses to a mmapped region the way flashrom does it?
Nope. Scattered resources/forum posts about ARMv7 suggest that peripheral memory is strongly ordered. Also, the U-Boot code doesn't have special handling for sync primitives AFAICT.
I'm pretty new to ARM... Any advice from experts on this list would be appreciated.
On Tue, Jun 28, 2011 at 5:54 PM, Carl-Daniel Hailfinger < c-d.hailfinger.devel.2006@gmx.net> wrote:
3-3-add_tegra2_spi_controller.patch Not your fault, but we really need a way to detect the target architecture in the Makefile. The issues of which SPI masters to include for internal exists on all architectures. Any ideas? I experimented with uname calls in the past, but that checks the host arch, not the target arch. Grepping the preprocessor output for the compiler might be an option. echo|gcc -dM -E -|grep "whatever|arch|defines" Or you try this pretty straightforward solution:
Create a file arch.h with these contents: #if defined (__i386__) #define __FLASHROM_ARCH__ "x86" #elif defined (__x86_64__) #define __FLASHROM_ARCH__ "x86_64" #elif defined (__mips) || defined (__mips__) || defined (_mips) || defined (mips) #define __FLASHROM_ARCH__ "mips" #elif defined(__powerpc__) || defined(__powerpc64__) || defined(__ppc__) || defined(__ppc64__) #define __FLASHROM_ARCH__ "ppc" #endif __FLASHROM_ARCH__
Then run gcc -E arch.h|grep -v ^# The result on my machine will be "x86" Side note: Such an arch.h file (with some extensions) might save us from having to check every possible arch define everywhere we need to differentiate between architectures.
I will comment on the Tegra2 SPI driver later, we should get the infrastructure questions addressed first.
I've updated this patch set on top of the other patches you've been working on (autodetect target processor http://patchwork.coreboot.org/patch/3256/ and the libpci hack http://patchwork.coreboot.org/patch/3255/).
The difference between this patchset and the previous one is pretty minor. We can now discard the first patch which #ifdef'd out PCI code for ARM targets. The remaining differences are mostly centered around the Makefile and arch.h
New patches are: Signed-off-by: David Hendricks dhendrix@google.com
Change-Id: I3bfaa4ee5035ff3dde92c42fda00785a86e569ee --- M Makefile M processor_enable.c M programmer.h A tegra2_spi.c A tegra2_spi.h 5 files changed, 549 insertions(+), 0 deletions(-)
git pull ssh://review.coreboot.org:29418/flashrom refs/changes/04/23804/1
diff --git a/Makefile b/Makefile index 26f978f..570dcc72 100644 --- a/Makefile +++ b/Makefile @@ -344,6 +344,10 @@ ifeq ($(ARCH),"x86") PROGRAMMER_OBJS += it87spi.o it85spi.o ichspi.o sb600spi.o wbsio_spi.o mcp6x_spi.o else +ifeq ($(ARCH),"arm") +PROGRAMMER_OBJS += tegra2_spi.o +else +endif endif NEED_PCI := yes endif diff --git a/processor_enable.c b/processor_enable.c index d680f97..1d363e7 100644 --- a/processor_enable.c +++ b/processor_enable.c @@ -81,6 +81,48 @@ } #endif
+#if defined(__arm__) +#include <stdio.h> +#include <string.h> +#include <ctype.h> + +/* Returns true if the /proc/cpuinfo contains a line: "CPU part *: *0xc09". + * TODO: need to extend in future for same SPI controller in chip family. + */ +static int is_tegra2(void) +{ + FILE *cpuinfo; + uint32_t impl = 0, architecture = 0, variant = 0, part = 0; + const char *name = "CPU part"; + const char *value = "0xc09"; + int ret = 0; + + cpuinfo = fopen("/proc/cpuinfo", "rb"); + if (!cpuinfo) + return 0; + while (!feof(cpuinfo)) { + char line[512], *ptr; + if (fgets(line, sizeof(line), cpuinfo) == NULL) + break; + ptr = line; + while (*ptr && isspace((unsigned char)*ptr)) + ptr++; + if (strncmp(ptr, name, strlen(name)) == 0) + ptr += strlen(name); + while (*ptr && isspace((unsigned char)*ptr)) + ptr++; + if (*ptr != ':') + continue; + ptr++; + while (*ptr && isspace((unsigned char)*ptr)) + ptr++; + ret = (strncmp(ptr, value, strlen(value)) == 0); + } + fclose(cpuinfo); + return ret; +} +#endif + int processor_flash_enable(void) { /* FIXME: detect loongson on FreeBSD and OpenBSD as well. */ @@ -90,6 +132,13 @@ return 0; } #endif + +#if defined (__arm__) + if (is_tegra2()) { + msg_pdbg("Detected NVIDIA Tegra 2.\n"); + return tegra2_spi_init(); + } +#endif /* Not implemented yet. Oh well. */ return 1; } diff --git a/programmer.h b/programmer.h index 6a28dbe..979f109 100644 --- a/programmer.h +++ b/programmer.h @@ -523,6 +523,9 @@ SPI_CONTROLLER_VIA, SPI_CONTROLLER_WBSIO, #endif +#if defined(__arm__) + SPI_CONTROLLER_TEGRA2, +#endif #endif #if CONFIG_FT2232_SPI == 1 SPI_CONTROLLER_FT2232, @@ -588,6 +591,13 @@ /* sb600spi.c */ int sb600_probe_spi(struct pci_dev *dev);
+/* tegra2_spi.c */ +int tegra2_spi_init(void); +int tegra2_spi_send_command(unsigned int writecnt, unsigned int readcnt, + const unsigned char *writearr, unsigned char *readarr); +int tegra2_spi_read(struct flashchip *flash, uint8_t *buf, int start, int len); +int tegra2_spi_write(struct flashchip *flash, uint8_t *buf, int start, int len); + /* wbsio_spi.c */ int wbsio_check_for_spi(void); #endif diff --git a/tegra2_spi.c b/tegra2_spi.c new file mode 100644 index 0000000..8168b79 --- /dev/null +++ b/tegra2_spi.c @@ -0,0 +1,405 @@ +/* + * This file is part of the flashrom project. + * + * Copyright (C) 2010 NVIDIA Corporation + * Copyright (C) 2011 Google Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#if defined(__arm__) +#include <assert.h> +#include <stdio.h> +#include <stdlib.h> +#include <string.h> + +#include "flash.h" +#include "programmer.h" +#include "tegra2_spi.h" + +static void *gpio_base, *clkrst_base, *apbmisc_base, *spi_base; + +#define SPI_TIMEOUT 50000 /* 100ms = 50000 * 2us */ + +/* On Seaboard: GPIO_PI3 = Port I = 8, bit = 3 */ +#define UART_DISABLE_PORT 8 +#define UART_DISABLE_BIT 3 + +/* Config port:bit as GPIO, not SFPIO (default) */ +static void __set_config(unsigned port, unsigned bit, int type) +{ + u32 u; + + msg_pdbg("%s: port = %d, bit = %d, %s\n", __func__, + port, bit, type ? "GPIO" : "SFPIO"); + + u = mmio_readl(GPIO_CNF(port)); + if (type) /* GPIO */ + u |= 1 << bit; + else + u &= ~(1 << bit); + rmmio_writel(u, GPIO_CNF(port)); +} + +/* Config GPIO port:bit as input or output (OE) */ +static void __set_direction(unsigned port, unsigned bit, int output) +{ + u32 u; + + msg_pdbg("%s: port = %d, bit = %d, %s\n", __func__, + port, bit, output ? "OUT" : "IN"); + + u = mmio_readl(GPIO_OE(port)); + if (output) + u |= 1 << bit; + else + u &= ~(1 << bit); + rmmio_writel(u, GPIO_OE(port)); +} + +/* set GPIO OUT port:bit as 0 or 1 */ +static void __set_level(unsigned port, unsigned bit, int high) +{ + u32 u; + + msg_pdbg("%s: port = %d, bit %d == %d\n", __func__, + port, bit, high); + + u = mmio_readl(GPIO_OUT(port)); + if (high) + u |= 1 << bit; + else + u &= ~(1 << bit); + rmmio_writel(u, GPIO_OUT(port)); +} + +/* set GPIO port:bit as an output, with polarity 'value' */ +static int tg2_gpio_direction_output(unsigned port, unsigned bit, int value) +{ + msg_pdbg("%s: port = %d, bit = %d, value = %d\n", + __func__, port, bit, value); + + /* Configure as a GPIO */ + __set_config(port, bit, 1); + + /* Configure GPIO output value. */ + __set_level(port, bit, value); + + /* Configure GPIO direction as output. */ + __set_direction(port, bit, 1); + + return 0; +} + +static void spi_cs_activate(void) +{ + uint32_t *spi_cmd = (uint32_t *)spi_base; + + /* + * CS is negated on Tegra, so drive a 1 to get a 0 + */ + mmio_writel(mmio_readl(spi_cmd) | SPI_CMD_CS_VAL, spi_cmd); + msg_pspew("%s: CS driven %s\n", __func__, + (mmio_readl(spi_cmd) & SPI_CMD_CS_VAL) ? "LOW" : "HIGH"); +} + +static void spi_cs_deactivate(void) +{ + uint32_t *spi_cmd = (uint32_t *)spi_base; + + + /* + * CS is negated on Tegra, so drive a 0 to get a 1 + */ + mmio_writel(mmio_readl(spi_cmd) & ~SPI_CMD_CS_VAL, spi_cmd); + msg_pspew("%s: CS driven %s\n", __func__, + (mmio_readl(spi_cmd) & SPI_CMD_CS_VAL) ? "LOW" : "HIGH"); +} + +/* Helper function to calculate the clock cycle in this round. + * Also updates the byte count remaining to be used this round. + * + * For example, we want to write 6 bytes to SPI and then read 5 bytes back. + * + * +---+---+---+---+---+---+ + * | W | W | W | W | W | W | + * +---+---+---+---+---+---+---+---+---+---+---+ + * | R | R | R | R | R | + * +---+---+---+---+---+ + * |<-- round 0 -->| + * |<-- round 1 -->| + * |<-- round 2 -->| + * + * So that the continuous calling this function would get: + * + * round| RET| writecnt readcnt bits to_write to_read + * -----+----+--------------------------------------------- + * INIT | | 6 5 + * 0 | 1 | 2 5 32 4 0 + * 1 | 1 | 0 3 32 2 2 + * 2 | 1 | 0 0 24 0 3 + * 3 | 0 | - - - - - + * + */ +int next4Bytes(uint32_t *writecnt, uint32_t *readcnt, int *num_bits, + uint32_t *to_write, uint32_t *to_read) { + assert(writecnt); + assert(readcnt); + assert(num_bits); + assert(to_write); + assert(to_read); + + *to_write = min(*writecnt, 4); + *to_read = min(*readcnt, 4 - *to_write); + + *writecnt -= *to_write; + *readcnt -= *to_read; + + *num_bits = (*to_write + *to_read) * 8; + + if (*num_bits) + return 1; /* need to be called again. */ + else + return 0; /* handled write and read requests. */ +} + +/* + * Tegra2 FIFO design is ... interesting. For example, you want to Tx 2 bytes: + * + * +---+---+ + * writearr[]: | 0 | 1 | + * +---+---+ + * \ \ + * \ \ + * \ \ + * \ \ + * \ \ + * 31 +---+---+---+---+ 0 + * tmp(32-bits): | X | X | 0 | 1 | + * +---+---+---+---+ LSB + * + * It is neither little or big endian. The first bit for SPI controller to + * transfer is the bit 15 in FIFO, neither bit 31 or bit 0, because the transfer + * length is 16 bits (2 bytes). + * + * Rx follows the similar rule. First bit comes at bit 0, and the whole FIFO + * left-shifts 1 bit for every bit comes in. Hence, after reading 3 bytes, + * the first coming bit will reside in bit 23. + */ +int tegra2_spi_send_command(unsigned int writecnt, + unsigned int readcnt, + const unsigned char *writearr, + unsigned char *readarr) +{ + int retval = 0; + uint8_t *delayed_msg = NULL; /* for UART is disabled. */ + uint32_t *spi_cmd = (uint32_t *)spi_base; + uint32_t *spi_sts = (uint32_t *)(spi_base + 0x04); + uint32_t *tx_fifo = (uint32_t *)(spi_base + 0x10); + uint32_t *rx_fifo = (uint32_t *)(spi_base + 0x20); + uint32_t status; + uint32_t to_write, to_read; /* byte counts to fill FIFO. */ + uint32_t bits; /* bit count to tell SPI controller. */ + + mmio_writel(mmio_readl(spi_sts), spi_sts); + mmio_writel(mmio_readl(spi_cmd) | SPI_CMD_TXEN | SPI_CMD_RXEN, spi_cmd); + spi_cs_activate(); + + while (next4Bytes(&writecnt, &readcnt, &bits, &to_write, &to_read)) { + int i; + uint32_t tmp; + uint32_t tm; /* timeout counter */ + + /* prepare Tx FIFO */ + for (tmp = 0, i = 0; i < to_write; ++i) { + tmp |= (*writearr++) << ((bits / 8 - 1 - i) * 8); + } + mmio_writel(tmp, tx_fifo); + + /* Kick the SCLK running: Shift out TX FIFO, and receive RX. */ + mmio_writel(mmio_readl(spi_cmd) & ~SPI_CMD_BIT_LENGTH_MASK, + spi_cmd); + mmio_writel(mmio_readl(spi_cmd) | (bits - 1), + spi_cmd); + mmio_writel(mmio_readl(spi_cmd) | SPI_CMD_GO, spi_cmd); + + /* Wait for controller completes the task. */ + for (tm = 0; tm < SPI_TIMEOUT; ++tm) { + if (((status = mmio_readl(spi_sts)) & + (SPI_STAT_BSY | SPI_STAT_RDY)) == SPI_STAT_RDY) + break; + /* We setup clock to 6MHz, so that we shall come back + * after: 1 / (6MHz) * 8 bits = 1.333us + */ + programmer_delay(2); + } + mmio_writel(mmio_readl(spi_sts) | SPI_STAT_RDY, spi_sts); + + /* Since the UART is disabled here, we delay printing the + * message until spi_cs_deactivate() is called. + */ + if (tm >= SPI_TIMEOUT) { + static uint8_t err[256]; + retval = -1; + snprintf(err, sizeof(err), + "%s():%d BSY&RDY timeout, status = 0x%08x\n", + __func__, __LINE__, status); + delayed_msg = err; + break; + } + + /* read RX FIFO */ + tmp = mmio_readl(rx_fifo); + for (i = 0; i < to_read; ++i) { + *readarr++ = (tmp >> ((to_read - 1 - i) * 8)) & 0xFF; + } + } + + mmio_writel(status = mmio_readl(spi_sts), spi_sts); + + spi_cs_deactivate(); + if (delayed_msg) { + msg_perr("%s\n", delayed_msg); + } + + return retval; +} + +int tegra2_spi_read(struct flashchip *flash, uint8_t *buf, int start, int len) +{ + return spi_read_chunked(flash, buf, start, len, + spi_programmer->max_data_read); +} + +int tegra2_spi_write(struct flashchip *flash, uint8_t *buf, int start, int len) +{ + return spi_write_chunked(flash, buf, start, len, + spi_programmer->max_data_write); +} + +/* Unmap register spaces */ +int tegra2_spi_shutdown(void *data) +{ + physunmap(gpio_base, 4096); + physunmap(clkrst_base, 4096); + physunmap(apbmisc_base, 4096); + physunmap(spi_base - 0x380, 4096); + return 0; +} + +static const struct spi_programmer spi_programmer_tegra2 = { + .type = SPI_CONTROLLER_TEGRA2, + /* FIFO depth is 32, packets can be up to 32-bits in length. */ + .max_data_read = 128, + .max_data_write = 128, + .command = tegra2_spi_send_command, + .multicommand = default_spi_send_multicommand, + .read = tegra2_spi_read, + .write_256 = tegra2_spi_write, +}; + +/* Map register spaces */ +int tegra2_spi_init(void) +{ + u32 val; + uint32_t *spi_cmd; + uint32_t *spi_sts; + + buses_supported = CHIP_BUSTYPE_SPI; + register_spi_programmer(&spi_programmer_tegra2); + + gpio_base = physmap("GPIO", TEGRA2_GPIO_BASE, 4096); + clkrst_base = physmap("CLK/RST", NV_ADDRESS_MAP_PPSB_CLK_RST_BASE, + 4096); + apbmisc_base = physmap("APB MISC", NV_ADDRESS_MAP_APB_MISC_BASE, 4096); + /* non-page offset */ + spi_base = physmap("SPI", TEGRA2_SPI_BASE - 0x380, 4096) + 0x380; + + register_shutdown(tegra2_spi_shutdown, NULL); + + flashbase = 0; /* FIXME: to make sanity check happy. */ + + /* Init variables */ + spi_cmd = (uint32_t *)spi_base; + spi_sts = (uint32_t *)(spi_base + 0x04); + + /* + * SPI reset/clocks init - reset SPI, set clocks, release from reset + */ + + /* SWE_SPI1_RST: Hold SPI controller 1 in reset */ + val = mmio_readl(clkrst_base + 0x08) | 0x800; + rmmio_writel(val, (clkrst_base + 0x08)); + msg_pdbg("%s: ClkRst = %08x\n", __func__, val); + + /* CLK_ENB_SPI1: Enable clock to SPI 1 Controller */ + val = mmio_readl(clkrst_base + 0x14) | 0x800; + rmmio_writel(val, (clkrst_base + 0x14)); + msg_pdbg("%s: ClkEnable = %08x\n", __func__, val); + + /* Change default SPI clock from 12MHz to 6MHz, same as BootROM */ + val = mmio_readl(clkrst_base + 0x114) | 0x2; + rmmio_writel(val, (clkrst_base + 0x114)); + msg_pdbg("%s: ClkSrc = %08x\n", __func__, val); + + /* SWE_SPI1_RST: Clear SPI1 reset bit (take it out of reset), + * use regular mmio_writel (restore callback already registered) */ + val = mmio_readl(clkrst_base + 0x08) & 0xFFFFF7FF; + mmio_writel(val, (clkrst_base + 0x08)); + msg_pdbg("%s: ClkRst final = %08x\n", __func__, val); + + /* Clear stale status here */ + mmio_writel(SPI_STAT_RDY | SPI_STAT_RXF_FLUSH | SPI_STAT_TXF_FLUSH | + SPI_STAT_RXF_UNR | SPI_STAT_TXF_OVF, spi_sts); + msg_pdbg("%s: STATUS = %08x\n", __func__, mmio_readl(spi_sts)); + + /* + * Use sw-controlled CS, so we can clock in data after ReadID, etc. + */ + mmio_writel(mmio_readl(spi_cmd) | SPI_CMD_CS_SOFT, spi_cmd); + msg_pdbg("%s: COMMAND = %08x\n", __func__, mmio_readl(spi_cmd)); + + /* + * SPI pins on Tegra2 are muxed - change pinmux last due to UART issue + */ + val = mmio_readl(apbmisc_base + 0x88) | 0xC0000000; + rmmio_writel(val, (apbmisc_base + 0x88)); + msg_pdbg("%s: PinMuxRegC = %08x\n", __func__, val); + + /* Set Z_LSPI to non-tristate mode */ + val = mmio_readl(apbmisc_base + 0x20) & 0xFFFFFFFE; + rmmio_writel(val, (apbmisc_base + 0x20)); + msg_pdbg("%s: TriStateReg = %08x\n", __func__, val); + + /* delay 100ms so that all chars in buffer (1KB) can be flushed. */ + programmer_delay(100000); + + /* + * We need to dynamically change the pinmux, shared w/UART RXD/CTS! + */ + val = mmio_readl(apbmisc_base + 0x84) | 0x0000000C; /* 3 = SFLASH */ + rmmio_writel(val, (apbmisc_base + 0x84)); + msg_pdbg("%s: PinMuxRegB = %08x\n", __func__, val); + + /* On Seaboard, MOSI/MISO are shared w/UART. + * Use GPIO I3 (UART_DISABLE) to tristate UART during SPI activity. + * Enable UART later (cs_deactivate) so we can use it for U-Boot comms. + */ + msg_pdbg("%s: DISABLING UART!\n", __func__); + tg2_gpio_direction_output(UART_DISABLE_PORT, UART_DISABLE_BIT, 1); + + return 0; +} +#endif diff --git a/tegra2_spi.h b/tegra2_spi.h new file mode 100644 index 0000000..0ab8f01 --- /dev/null +++ b/tegra2_spi.h @@ -0,0 +1,81 @@ +/* + * This file is part of the flashrom project. + * + * Copyright (C) 2010 NVIDIA Corporation + * Copyright (C) 2011 Google Inc + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA + */ + +#ifndef __TEGRA2_SPI_H__ +#define __TEGRA2_SPI_H__ + +// *************************************************************************** +// Hardware BARs + +#define TEGRA2_GPIO_BASE 0x6000D000 +#define TEGRA2_SPI_BASE 0x7000C380 +#define NV_ADDRESS_MAP_PPSB_CLK_RST_BASE 0x60006000 +#define NV_ADDRESS_MAP_APB_MISC_BASE 0x70000000 + +// *************************************************************************** +// Clock/reset controller +#define CLK_RST_ENB_H_0_OFFSET 0x14 +#define CLK_RST_ENB_H_0_SPI1 (1 << 11) + +// *************************************************************************** +// GPIO controller + +#define GPIO_OFF(port) (((port / 4) * 128) + ((port % 4) * 4)) +#define GPIO_CNF(port) (gpio_base + GPIO_OFF(port) + 0x00) +#define GPIO_OE(port) (gpio_base + GPIO_OFF(port) + 0x10) +#define GPIO_OUT(port) (gpio_base + GPIO_OFF(port) + 0x20) +#define GPIO_IN(port) (gpio_base + GPIO_OFF(port) + 0x30) +#define GPIO_INT_STA(port) (gpio_base + GPIO_OFF(port) + 0x40) +#define GPIO_INT_ENB(port) (gpio_base + GPIO_OFF(port) + 0x50) +#define GPIO_INT_LVL(port) (gpio_base + GPIO_OFF(port) + 0x60) +#define GPIO_INT_CLR(port) (gpio_base + GPIO_OFF(port) + 0x70) + +#define SPI_CMD_GO (1 << 30) +#define SPI_CMD_ACTIVE_SCLK (1 << 26) +#define SPI_CMD_CK_SDA (1 << 21) +#define SPI_CMD_ACTIVE_SDA (1 << 18) +#define SPI_CMD_CS_POL (1 << 16) +#define SPI_CMD_TXEN (1 << 15) +#define SPI_CMD_RXEN (1 << 14) +#define SPI_CMD_CS_VAL (1 << 13) +#define SPI_CMD_CS_SOFT (1 << 12) +#define SPI_CMD_CS_DELAY (1 << 9) +#define SPI_CMD_CS3_EN (1 << 8) +#define SPI_CMD_CS2_EN (1 << 7) +#define SPI_CMD_CS1_EN (1 << 6) +#define SPI_CMD_CS0_EN (1 << 5) +#define SPI_CMD_BIT_LENGTH (1 << 4) +#define SPI_CMD_BIT_LENGTH_MASK 0x0000001F + +#define SPI_STAT_BSY (1 << 31) +#define SPI_STAT_RDY (1 << 30) +#define SPI_STAT_RXF_FLUSH (1 << 29) +#define SPI_STAT_TXF_FLUSH (1 << 28) +#define SPI_STAT_RXF_UNR (1 << 27) +#define SPI_STAT_TXF_OVF (1 << 26) +#define SPI_STAT_RXF_EMPTY (1 << 25) +#define SPI_STAT_RXF_FULL (1 << 24) +#define SPI_STAT_TXF_EMPTY (1 << 23) +#define SPI_STAT_TXF_FULL (1 << 22) +#define SPI_STAT_SEL_TXRX_N (1 << 16) +#define SPI_STAT_CUR_BLKCNT (1 << 15) + +#endif /* __TEGRA2_SPI_H__ */
-
Nico Huber (Code Review)