flashrom

flashrom@flashrom.org

5 participants
9161 discussions

Re: [flashrom] Tested AT25DF161
by Stefan Tauner 01 Mar '14

01 Mar '14

On Sun, 2 Mar 2014 00:28:16 +0400 Alex K <lepik.stv(a)gmail.com> wrote: > Sorry, I do not quite understand your question, but I'll try to answer. > I forgot when recording chip, specify a log file entry. Because I have a > log file cleanup, and reading to compare the recorded information. > To clean the chip pin WP, I connect to the GND. For writing and reading > from the chip, pin WP connects to the VCC. > > […] > > I hope this information will help you. Yes, thank you. I'll mark the chip as fully tested. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

Re: [flashrom] Tested AT25DF161
by Stefan Tauner 01 Mar '14

01 Mar '14

On Sat, 1 Mar 2014 23:12:15 +0400 Alex K <lepik.stv(a)gmail.com> wrote: > Hello I tested for cleaning work, reading, writing, memory AT25DF161 using > Bus Pirate v4. > Used: > flashrom v0.9.6.1-r1704 on Windows 6.1 (x86) > flashrom was built with GCC 4.7.2, little endian > Baud rate is 115200. > Detected Bus Pirate hardware v4 > Detected Bus Pirate firmware 6.2 ("v6.2-beta1") > Using SPI command set v2. > SPI speed is 8MHz > Raw bitbang mode version 1 > Raw SPI mode version 1 > The following protocols are supported: SPI. > Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0x1f, id2 > 0x4602 > Found Atmel flash chip "AT25DF161" (2048 kB, SPI) on buspirate_spi. > Ignoring security lockdown (if present) > Ignoring status register byte 2 > Chip status register is 0x0c. > Chip status register: Sector Protection Register Lock (SRPL) is not set > Chip status register: Bit 6 is not set > Chip status register: Erase/Program Error (EPE) is not set > Chip status register: WP# pin (WPP) is asserted > Chip status register: Software Protection Status (SWP): all sectors are > protected > Chip status register: Write Enable Latch (WEL) is not set > Chip status register: Write In Progress (WIP/BUSY) is not set > === > > Initially, there was a problem with the use of long cables (> 20 cm). > After verification of the firmware did not pass. > Replaced wires from Bus Pirate at length (10cm), all turned out. Many > thanks for the utility. I think that you can remove the status UNTESTED > with this chip. Thank you again. > I think it is reasonable to point out the page on the wiki that the length > of wire for the Bus Pirate is very desirable <= 10 cm, to avoid many > mistakes. This saves the trouble of starting recording, reading chips. > > Sorry for my bad english, I'm from Russia. Hello Alex, thanks for your report! I am wondering a bit about the status register bits. According to your log the software write protection is enabled (and the parsing of the raw value 0x0c seems to be correct, so this is not only a cosmetic problem). Did you change anything since you wrote to the chip? Regarding the cable lengths: The troubleshooting section of the bus pirate wiki page links to this: http://flashrom.org/ISP and the first problem mentioned there are too long cables ;) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

2 1

Tested AT25DF161
by Alex K 01 Mar '14

01 Mar '14

Hello I tested for cleaning work, reading, writing, memory AT25DF161 using Bus Pirate v4. Used: flashrom v0.9.6.1-r1704 on Windows 6.1 (x86) flashrom was built with GCC 4.7.2, little endian Baud rate is 115200. Detected Bus Pirate hardware v4 Detected Bus Pirate firmware 6.2 ("v6.2-beta1") Using SPI command set v2. SPI speed is 8MHz Raw bitbang mode version 1 Raw SPI mode version 1 The following protocols are supported: SPI. Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0x1f, id2 0x4602 Found Atmel flash chip "AT25DF161" (2048 kB, SPI) on buspirate_spi. Ignoring security lockdown (if present) Ignoring status register byte 2 Chip status register is 0x0c. Chip status register: Sector Protection Register Lock (SRPL) is not set Chip status register: Bit 6 is not set Chip status register: Erase/Program Error (EPE) is not set Chip status register: WP# pin (WPP) is asserted Chip status register: Software Protection Status (SWP): all sectors are protected Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set === Initially, there was a problem with the use of long cables (> 20 cm). After verification of the firmware did not pass. Replaced wires from Bus Pirate at length (10cm), all turned out. Many thanks for the utility. I think that you can remove the status UNTESTED with this chip. Thank you again. I think it is reasonable to point out the page on the wiki that the length of wire for the Bus Pirate is very desirable <= 10 cm, to avoid many mistakes. This saves the trouble of starting recording, reading chips. Sorry for my bad english, I'm from Russia. -- С уважением Алексей

1 0

FAILED: SST49LF004A/B
by Tim Sebastian 28 Feb '14

28 Feb '14

Hello, I'm trying to use flashrom to write a new bios to my device. It successfully writes the beginning of the bios and then fails with the error: 0x040000-0x040fff:W writing sector at 0xb7ea0000 failed! And again with the second erase function : Trying erase function 1... 0x000000-0x00ffff:EW, 0x010000-0x01ffff:S, 0x020000-0x02ffff:S, 0x030000-0x03ffff:S, 0x040000-0x04ffff:W writing sector at 0xb7ea0000 failed! leaving the bios in an unstable state. Further experimentation shows that writing the bios fails on both erasing and writing any sector after 0x040000, which is exactly halfway through the bios (2Mb out of 4Mb). Reading from those areas works without a problem. The lock status for every block is reported as 00, full access. Full log is below. I took a look at the source code for flashrom in order to see if I could easily fix the problem. I created a minimal flashrom-like clone that works with my chip: #include <sys/types.h> #include <sys/stat.h> #include <fcntl.h> #include <stdio.h> #include <sys/mman.h> #define D(bios, pos) *((volatile char*)bios + pos) void write_byte(void* bios, int pos, char value) { char tmp1, tmp2; int i = 0; int tries = 4; retry: D(bios, 0x5555) = 0xAA; D(bios, 0x2AAA) = 0x55; D(bios, 0x5555) = 0xA0; D(bios, pos) = value; tmp1 = D(bios, 0) & 0x40; while (i++ < 0xFFFFFFF) { tmp2 = D(bios, 0) & 0x40; if (tmp1 == tmp2) { break; } tmp1 = tmp2; } if (D(bios, pos) != value) { if (tries > 0) { tries--; goto retry; } printf("Error writing value\n"); } } void try_replace(void* bios, int pos) { printf("Pos = %x:\n", pos); printf("Old: %hhx\n", D(bios, pos)); write_byte(bios, pos, 0); printf("New: %hhx\n", D(bios, pos)); printf("\n"); } int main() { int fd = open("/dev/mem", O_RDWR); void *bios = mmap(NULL, 0x80000, PROT_READ | PROT_WRITE, MAP_SHARED, fd, 0xfff80000); char old; try_replace(bios, 0); try_replace(bios, 0x20000); try_replace(bios, 0x3ff00); try_replace(bios, 0x40000); try_replace(bios, 0x50000); try_replace(bios, 0x60000); try_replace(bios, 0x70000); munmap(bios, 0x80000); close(fd); return 0; } And it outputs: Pos = 0: Old: 25 New: 0 Pos = 20000: Old: 81 New: 0 Pos = 3ff00: Old: ff New: 0 Pos = 40000: Old: ff Error writing value New: ff Pos = 50000: Old: ff Error writing value New: ff Pos = 60000: Old: ff Error writing value New: ff Pos = 70000: Old: ff Error writing value New: ff *Note that running this script will write garbage to your bios. Make sure to keep an original backup nearby.* As you can see, the problem is easily reproducible. What can cause writing to fail on where the high bit of the address is set (0x40000-0x7ffff)? Full log: =========================================== flashrom v0.9.7-r1711 on Linux 2.6.35.12 (i586) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.2.0, GCC 4.6.1, little endian Command line (5 args): ./flashrom --programmer internal -w my_bios -V Calibrating delay loop... OS timer resolution is 4 usecs, 78M loops per second, 10 myus = 12 us, 100 myus = 108 us, 1000 myus = 1030 us, 10000 myus = 10131 us, 16 myus = 21 us, OK. Initializing internal programmer No coreboot table found. sh: dmidecode: not found dmidecode execution unsuccessful - continuing without DMI info Found Winbond Super I/O, id 0x52 WARNING: No chipset found. Flash detection will most likely fail. The following protocols are supported: Non-SPI. Probing for AMD Am29F010A/B, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BB, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F002(N)BT, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F016D, 2048 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F040B, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29F080B, 1024 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BB, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV001BT, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BB, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV002BT, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BB, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV004BT, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BB, 1024 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV008BT, 1024 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV040B, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMD Am29LV081B, 1024 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002B, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29002T, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC A29040B, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for AMIC A49LF040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT29C512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C010A, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT29C040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT49BV512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49F002(N), 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49F002(N)T, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49(H)F010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49F020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Atmel AT49F040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT49F080, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT49F080T, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Catalyst CAT28F512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Bright BM29F040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for ESMT F49B002UA, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)B, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29F002(A)(N)T, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Eon EN29LV640B, 8192 kB: probe_en29lv640b: id1 0x0000, id2 0x0000 Probing for Fujitsu MBM29F004BC, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F004TC, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Fujitsu MBM29F400BC, 512 kB: probe_m29f400bt: id1 0x25, id2 0x2d Probing for Fujitsu MBM29F400TC, 512 kB: probe_m29f400bt: id1 0x25, id2 0x2d Probing for Hyundai HY29F002T, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Hyundai HY29F002B, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Hyundai HY29F040A, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-B, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F001BN/BX-T, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F002BC/BL/BV/BX-T, 256 kB: probe_82802ab: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F008S3/S5/SC, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-B, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F004B5/BE/BV/BX-T, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-B, 512 kB: probe_82802ab: id1 0x25, id2 0x2d, id1 is normal flash content, id2 is normal flash content Probing for Intel 28F400BV/BX/CE/CV-T, 512 kB: probe_82802ab: id1 0x25, id2 0x2d, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001B, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F001T, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)B, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F002(N)T, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29F040, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX29LV040, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000B, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51000T, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29C51400B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for MoselVitelic V29C51400T, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for MoselVitelic V29LC51000, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51001, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for MoselVitelic V29LC51002, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002T, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm29F002B, 256 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV040, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm39LV512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Sharp LH28F008BJT-BTLZ1, 1024 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST28SF040A, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29LE010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29EE020A, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST29LE020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF010A, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF020A, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39SF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39VF512, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST39VF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST39VF080, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Found SST flash chip "SST49LF004A/B" (512 kB, FWH) at physical address 0xfff80000. Lock status for 0x000000 (size 0x010000) is 00, full access Lock status for 0x010000 (size 0x010000) is 00, full access Lock status for 0x020000 (size 0x010000) is 00, full access Lock status for 0x030000 (size 0x010000) is 00, full access Lock status for 0x040000 (size 0x010000) is 00, full access Lock status for 0x050000 (size 0x010000) is 00, full access Lock status for 0x060000 (size 0x010000) is 00, full access Lock status for 0x070000 (size 0x010000) is 00, full access Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF080A, 1024 kB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xbf, id2 0x60 Probing for SST SST49LF160C, 2048 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002B, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F002T/NT, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29F040B, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M29F400BB, 512 kB: probe_m29f400bt: id1 0x25, id2 0x2d Probing for ST M29F400BT, 512 kB: probe_m29f400bt: id1 0x25, id2 0x2d Probing for ST M29W010B, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M29W040B, 512 kB: probe_jedec_common: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M29W512B, 64 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 kB: probe_82802ab: id1 0x25, id2 0x7b, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for TI TMS29F002RB, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for TI TMS29F002RT, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012-old, 128 kB: Old Winbond W29* probe method disabled because the probing sequence puts the AMIC A49LF040A in a funky state. Use 'flashrom -c W29C010(M)/W29C011A/W29EE011/W29EE012-old' if you have a board with such a chip. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C020(C)/W29C022, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W29C040/P, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39F010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39L010, 128 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39L020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39L040, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040A, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040B, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040C, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V080A, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W49F002U/N, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F020, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002A, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xd2, id2 0xce, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0xbf, id2 0x60 Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xbf, id2 0x60 Found SST flash chip "SST49LF004A/B" (512 kB, FWH). Lock status for 0x000000 (size 0x010000) is 00, full access Lock status for 0x010000 (size 0x010000) is 00, full access Lock status for 0x020000 (size 0x010000) is 00, full access Lock status for 0x030000 (size 0x010000) is 00, full access Lock status for 0x040000 (size 0x010000) is 00, full access Lock status for 0x050000 (size 0x010000) is 00, full access Lock status for 0x060000 (size 0x010000) is 00, full access Lock status for 0x070000 (size 0x010000) is 00, full access Flash image seems to be a legacy BIOS. Disabling coreboot-related checks. Reading old flash chip contents... done. Erasing and writing flash chip... Trying erase function 0... 0x000000-0x000fff:S, 0x001000-0x001fff:S, 0x002000-0x002fff:S, 0x003000-0x003fff:S, 0x004000-0x004fff:S, 0x005000-0x005fff:S, 0x006000-0x006fff:S, 0x007000-0x007fff:S, 0x008000-0x008fff:S, 0x009000-0x009fff:S, 0x00a000-0x00afff:S, 0x00b000-0x00bfff:S, 0x00c000-0x00cfff:S, 0x00d000-0x00dfff:S, 0x00e000-0x00efff:S, 0x00f000-0x00ffff:S, 0x010000-0x010fff:S, 0x011000-0x011fff:S, 0x012000-0x012fff:S, 0x013000-0x013fff:S, 0x014000-0x014fff:S, 0x015000-0x015fff:S, 0x016000-0x016fff:S, 0x017000-0x017fff:S, 0x018000-0x018fff:S, 0x019000-0x019fff:S, 0x01a000-0x01afff:S, 0x01b000-0x01bfff:S, 0x01c000-0x01cfff:S, 0x01d000-0x01dfff:S, 0x01e000-0x01efff:S, 0x01f000-0x01ffff:S, 0x020000-0x020fff:S, 0x021000-0x021fff:S, 0x022000-0x022fff:S, 0x023000-0x023fff:S, 0x024000-0x024fff:S, 0x025000-0x025fff:S, 0x026000-0x026fff:S, 0x027000-0x027fff:S, 0x028000-0x028fff:S, 0x029000-0x029fff:S, 0x02a000-0x02afff:S, 0x02b000-0x02bfff:S, 0x02c000-0x02cfff:S, 0x02d000-0x02dfff:S, 0x02e000-0x02efff:S, 0x02f000-0x02ffff:S, 0x030000-0x030fff:S, 0x031000-0x031fff:S, 0x032000-0x032fff:S, 0x033000-0x033fff:S, 0x034000-0x034fff:S, 0x035000-0x035fff:S, 0x036000-0x036fff:S, 0x037000-0x037fff:S, 0x038000-0x038fff:S, 0x039000-0x039fff:EW, 0x03a000-0x03afff:W, 0x03b000-0x03bfff:W, 0x03c000-0x03cfff:W, 0x03d000-0x03dfff:W, 0x03e000-0x03efff:W, 0x03f000-0x03ffff:W, 0x040000-0x040fff:W writing sector at 0xb7ea0000 failed! Reading current flash chip contents... done. Looking for another erase function. Trying erase function 1... 0x000000-0x00ffff:EW, 0x010000-0x01ffff:S, 0x020000-0x02ffff:S, 0x030000-0x03ffff:S, 0x040000-0x04ffff:W writing sector at 0xb7ea0000 failed! Looking for another erase function. No usable erase functions left. FAILED! Uh oh. Erase/write failed. Checking if anything changed. Your flash chip is in an unknown state. Get help on IRC at chat.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with the subject "FAILED: <your board name>"! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF!

3 2

Getting Flashrom running on OS X v10.9.2 (Mavericks)
by Nicholas Ouimet 27 Feb '14

27 Feb '14

Hi Flashrom community, I'm trying to install Flashrom 0.9.7 on OS X v10.9.2 and I download the source, and then use terminal commands cd make AND I get an error Checking for libpci headers... .test.c:3:10: fatal error: 'pci/pci.h' file not found #include <pci/pci.h> So I read that I need to install PCUtils, and again, using the cd and then make, I get an error 192:~ ouimetnick$ cd /Users/ouimetnick/Desktop/flashrom/pciutils-3.1.9 192:pciutils-3.1.9 ouimetnick$ make /Applications/Xcode.app/Contents/Developer/usr/bin/make -C lib all make[1]: *** No rule to make target `/System/Library/Frameworks/ApplicationServices.framework/Headers/ApplicationServices.h', needed by `DirectHW.o'. Stop. make: *** [lib/libpci.a] Error 2 192:pciutils-3.1.9 ouimetnick$ How do I fix and install this? Also, DirectHW needs to be installed, and when attempting to install that (using the cd, and then make command), I get the following ** BUILD FAILED ** The following build commands failed: CompileC build/DirectHW.build/Release/KEXT.build/Objects-normal/i386/DirectHW.o DirectHW.cpp normal i386 c++ com.apple.compilers.llvm.clang.1_0.compiler (1 failure) make: *** [build] Error 65 192:DirectHW ouimetnick$ Could anyone offer some help? I want to get Flashrom running so I can use my Bus Pirate. Thanks, Nick ouimetnick(a)gmail.com

1 0

Re: [flashrom] flashrom support for SST26VF064B
by Stefan Tauner 27 Feb '14

27 Feb '14

On Wed, 26 Feb 2014 14:57:32 -0800 Wei Hu <wei(a)aristanetworks.com> wrote: > Hi flashrom folks, > > I'm trying to add support for SST26VF064B after I got a patch from Elias. I > made some changes to it after reading the datasheet, but none of the block > erasing commands worked, and I don't know why... I don't see obvious problems either, but I did not read the datasheet. Two things I would check: - is there a write protection pin or register bits that might silently block any modification requests? - is the opcode sequence including wren? (this is probably done automatically by the ichspi driver, but i cant remember the details) And you could test if hardware sequencing (or SFDP) works as a workaround (but I doubt SFDP would behave differently for the lower block sizes and some of them are obviously wrong in the SFDP table anyway (or you have found a bug)). A full verbose log could shed some more light on it too, but I doubt it. If we get this to work we would probably like to commit this patch. For this either of you must sign it off according to http://www.coreboot.org/Development_Guidelines#Sign-off_Procedure -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

flashrom support for SST26VF064B
by Wei Hu 26 Feb '14

26 Feb '14

Hi flashrom folks, I'm trying to add support for SST26VF064B after I got a patch from Elias. I made some changes to it after reading the datasheet, but none of the block erasing commands worked, and I don't know why... Erasing and writing flash chip... *Trying erase function 0... 0x000000-0x000fff*:E program_opcodes: preop=5006 optype=463b opmenu=05200302c79f0190 on-the-fly *OPCODE (0x20)* re-programmed, op-pos=2 FAILED at 0x00000010! Expected=0xff, Found=0x5a, failed byte count from 0x00000000-0x00000fff: 0x83 ERASE FAILED! Reading current flash chip contents... done. Looking for another erase function. *Trying erase function 1... 0x000000-0x00ffff*:E program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 on-the-fly *OPCODE (0xD8)* re-programmed, op-pos=2 FAILED at 0x00000010! Expected=0xff, Found=0x5a, failed byte count from 0x00000000-0x0000ffff: 0xdf16 ERASE FAILED! Reading current flash chip contents... done. Looking for another erase function. *Trying erase function 2... 0x000000-0x7fffff*:EFAILED at 0x00000010! Expected=0xff, Found=0x5a, failed byte count from 0x00000000-0x007fffff: 0x702b2a ERASE FAILED! Looking for another erase function. No usable erase functions left. FAILED! It tried the commands for erasing 4KB, 64KB, 8MB, and all failed... This is basically what I had in the block_erasers[] array. Full diff is attached. Thanks for your help! { { .eraseblocks = { {4 * 1024, 2048} }, .block_erase = spi_block_erase_20, }, { .eraseblocks = { {64 * 1024, 128} }, .block_erase = spi_block_erase_d8, }, { .eraseblocks = { {8 * 1024 * 1024, 1} }, .block_erase = spi_block_erase_c7, }, },

1 0

W836xx: Lenovo 2325AEG: flashrom -V
by Stefan Midjich 26 Feb '14

26 Feb '14

flashrom v0.9.5.2-r1546 on Linux 3.2.0-4-amd64 (x86_64) flashrom is free software, get the source code at http://www.flashrom.org flashrom was built with libpci 3.1.7, GCC 4.6.2, little endian Command line (3 args): flashrom -p internal -V Calibrating delay loop... OS timer resolution is 1 usecs, 3185M loops per second, 10 myus = 10 us, 100 myus = 120 us, 1000 myus = 1021 us, 10000 myus = 10016 us, 4 myus = 4 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "LENOVO" DMI string system-product-name: "2325AEG" DMI string system-version: "ThinkPad X230" DMI string baseboard-manufacturer: "LENOVO" DMI string baseboard-product-name: "2325AEG" DMI string baseboard-version: "Win8 Pro DPK TPG" DMI string chassis-type: "Notebook" Laptop detected via DMI. W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 00. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. -- Hälsningar / Greetings http://Stefan.Midjich.name

1 0

laptop bios
by Sheri Soltz 26 Feb '14

26 Feb '14

I am trying to use flashrom to make a bios backup file on my lenovo thinkpad x131e chromebook (intel celeron 1007u cpu). I have set developer-mode and have physically opened the laptop and set the write protect switch to the write enable position. I am using the command "sudo flashrom -p internal -r backup.bin -o backup.log" But when I check the md5sum for backup.bin it is different from each previous backup.bin. Shouldn't the md5sum of the backup stay the same, as long as the bios has not been changed? Here is the output from backup.log: flashrom v0.9.7-r1711 on Linux 3.8.11 (x86_64) flashrom was built with libpci 3.1.8, GCC 4.6.3, little endian Command line (7 args): flashrom -p internal -r bku1.bin -o bku1.log -V Calibrating delay loop... OS timer resolution is 1 usecs, 1493M loops per second, 10 myus = 10 us, 100 myus = 99 us, 1000 myus = 1002 us, 10000 myus = 10007 us, 4 myus = 4 us, OK. Initializing internal programmer Found candidate at: 00000500-00000510 Found coreboot table at 0x00000500. Found candidate at: 00000000-000003d8 Found coreboot table at 0x00000000. coreboot table found at 0xacedd000. coreboot header(24) checksum: 7b8d table(984) checksum: eeda entries: 18 Vendor ID: GOOGLE, part ID: Stout DMI string system-manufacturer: "GOOGLE" DMI string system-product-name: "Stout" DMI string system-version: "1.0" DMI string baseboard-manufacturer: "" DMI string baseboard-product-name: "" DMI string baseboard-version: "" DMI string chassis-type: "Desktop" W836xx enter config mode worked or we were already in config mode. W836xx leave config mode had no effect. Active config mode, unknown reg 0x20 ID: 85. Please send the output of "flashrom -V" to flashrom(a)flashrom.org with W836xx: your board name: flashrom -V as the subject to help us finish support for your Super I/O. Thanks. Found ITE EC, ID 0x8518, Rev 0x08 on port 0x2e. Found chipset "Intel HM77" with PCI ID 8086:1e57. This chipset is marked as untested. If you are using an up-to-date version of flashrom *and* were (not) able to successfully update your firmware with it, then please email a report to flashrom(a)flashrom.org including a verbose (-V) log. Thank you! Enabling flash write... 0xfff80000/0xffb80000 FWH IDSEL: 0x0 0xfff00000/0xffb00000 FWH IDSEL: 0x0 0xffe80000/0xffa80000 FWH IDSEL: 0x1 0xffe00000/0xffa00000 FWH IDSEL: 0x1 0xffd80000/0xff980000 FWH IDSEL: 0x2 0xffd00000/0xff900000 FWH IDSEL: 0x2 0xffc80000/0xff880000 FWH IDSEL: 0x3 0xffc00000/0xff800000 FWH IDSEL: 0x3 0xff700000/0xff300000 FWH IDSEL: 0x4 0xff600000/0xff200000 FWH IDSEL: 0x5 0xff500000/0xff100000 FWH IDSEL: 0x6 0xff400000/0xff000000 FWH IDSEL: 0x7 0xfff80000/0xffb80000 FWH decode enabled 0xfff00000/0xffb00000 FWH decode enabled 0xffe80000/0xffa80000 FWH decode enabled 0xffe00000/0xffa00000 FWH decode enabled 0xffd80000/0xff980000 FWH decode enabled 0xffd00000/0xff900000 FWH decode enabled 0xffc80000/0xff880000 FWH decode enabled 0xffc00000/0xff800000 FWH decode enabled 0xff700000/0xff300000 FWH decode enabled 0xff600000/0xff200000 FWH decode enabled 0xff500000/0xff100000 FWH decode enabled 0xff400000/0xff000000 FWH decode enabled Maximum FWH chip size: 0x100000 bytes BIOS_CNTL = 0x09: BIOS Lock Enable: disabled, BIOS Write Enable: enabled Root Complex Register Block address = 0xfed1c000 GCS = 0xc21: BIOS Interface Lock-Down: enabled, Boot BIOS Straps: 0x3 (SPI) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0xc000 (HSFS) HSFS: FDONE=0, FCERR=0, AEL=0, BERASE=0, SCIP=0, FDOPSS=0, FDV=1, FLOCKDN=1 Warning: SPI Configuration Lockdown activated. The Flash Descriptor Override Strap-Pin is set. Restrictions implied by the Master Section of the flash descriptor are NOT in effect. Please note that Protected Range (PR) restrictions still apply. Reading OPCODES... done OP Type Pre-OP op[0]: 0x01, write w/o addr, none op[1]: 0x02, write w/ addr, none op[2]: 0x03, read w/ addr, none op[3]: 0x05, read w/o addr, none op[4]: 0x20, write w/ addr, none op[5]: 0x9f, read w/o addr, none op[6]: 0xd8, write w/ addr, none op[7]: 0x0b, read w/ addr, none Pre-OP 0: 0x06, Pre-OP 1: 0x50 0x06: 0x0000 (HSFC) HSFC: FGO=0, FCYCLE=0, FDBC=0, SME=0 0x08: 0x00000000 (FADDR) 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00000000 FREG0: Flash Descriptor region (0x00000000-0x00000fff) is read-write. 0x58: 0x07ff0200 FREG1: BIOS region (0x00200000-0x007fffff) is read-write. 0x5C: 0x01ff0001 FREG2: Management Engine region (0x00001000-0x001fffff) is read-write. 0x60: 0x00001fff FREG3: Gigabit Ethernet region is unused. 0x64: 0x00001fff FREG4: Platform Data region is unused. 0x74: 0x00000000 (PR0 is unused) 0x78: 0x00000000 (PR1 is unused) 0x7C: 0x00000000 (PR2 is unused) 0x80: 0x00000000 (PR3 is unused) 0x84: 0x00000000 (PR4 is unused) 0x90: 0xc0 (SSFS) SSFS: SCIP=0, FDONE=0, FCERR=0, AEL=0 0x91: 0xf94400 (SSFC) SSFC: SCGO=0, ACS=0, SPOP=0, COP=0, DBC=4, SME=0, SCF=1 0x94: 0x5006 (PREOP) 0x96: 0xb32d (OPTYPE) 0x98: 0x05030201 (OPMENU) 0x9C: 0x0bd89f20 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xC4: 0x00000000 (LVSCC) LVSCC: BES=0x0, WG=0, WSR=0, WEWS=0, EO=0x0, VCL=0 0xC8: 0x00000000 (UVSCC) UVSCC: BES=0x0, WG=0, WSR=0, WEWS=0, EO=0x0, VCL=0 0xD0: 0x00000000 (FPB) Reading flash descriptors mapped by the chipset via FDOC/FDOD... done. === Content Section === FLVALSIG 0x0ff0a55a FLMAP0 0x02040003 FLMAP1 0x12100206 FLMAP2 0x00210120 --- Details --- NR (Number of Regions): 3 FRBA (Flash Region Base Address): 0x040 NC (Number of Components): 1 FCBA (Flash Component Base Address): 0x030 ISL (ICH/PCH Strap Length): 18 FISBA/FPSBA (Flash ICH/PCH Strap Base Address): 0x100 NM (Number of Masters): 3 FMBA (Flash Master Base Address): 0x060 MSL/PSL (MCH/PROC Strap Length): 1 FMSBA (Flash MCH/PROC Strap Base Address): 0x200 === Component Section === FLCOMP 0x49300024 FLILL 0x00000000 --- Details --- Component 1 density: 8 MB Component 2 is not used. Read Clock Frequency: 20 MHz Read ID and Status Clock Freq.: 33 MHz Write and Erase Clock Freq.: 33 MHz Fast Read is supported. Fast Read Clock Frequency: 33 MHz No forbidden opcodes. === Region Section === FLREG0 0x00000000 FLREG1 0x07ff0200 FLREG2 0x01ff0001 FLREG3 0x00001fff FLREG4 0x00001fff --- Details --- Region 0 (Descr.) 0x00000000 - 0x00000fff Region 1 (BIOS ) 0x00200000 - 0x007fffff Region 2 (ME ) 0x00001000 - 0x001fffff Region 3 (GbE ) is unused. Region 4 (Platf.) is unused. === Master Section === FLMSTR1 0x0a0b0000 FLMSTR2 0x0c0d0000 FLMSTR3 0x08080118 --- Details --- Descr. BIOS ME GbE Platf. BIOS r rw rw ME r rw rw GbE rw SPI Read Configuration: prefetching enabled, caching enabled, OK. Super I/O ID 0x8518 is not on the list of flash capable controllers. No board enable found matching coreboot IDs vendor="GOOGLE", model="Stout". The following protocols are supported: FWH, SPI. Probing for AMIC A25L05PT, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L05PU, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L10PT, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L10PU, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L20PT, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L20PU, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L40PT, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L40PU, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L80P, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L16PT, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L16PU, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L080, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25L032, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25LQ16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25LQ032/A25LQ32A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for AMIC A25LQ64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF021, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF041A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF081, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF321, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF321A, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DF641(A), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25DQ161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25F512, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512A, 64 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F512B, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25F1024(A), 128 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F2048, 256 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25F4096, 512 kB: Invalid OPCODE 0x15, will not execute. Probing for Atmel AT25FS010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT25FS040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF041, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF081A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF161, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26DF161A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT26F004, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45CS1282, 16896 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB011D, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB021D, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB041D, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB081D, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB161D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB321C, 4224 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB321D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel AT45DB642D, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ESMT F25L008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B05T, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B10T, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B20T, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B40T, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B80T, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B16T, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B32T, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25B64T, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F05, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25F64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q80(A), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q32(A/B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25Q128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25QH128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon EN25S64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25LQ32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q20(B), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q40(B), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q80(B), 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q16(B), 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q32(B), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q64(B), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25Q128B, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for GigaDevice GD25T80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F160S33B8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F160S33T8, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F320S33B8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F320S33T8, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F640S33B8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Intel 25F640S33T8, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L512(E)/MX25V512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1005(C)/MX25L1006E, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L2005(C), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L4005(A/C), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L8005/MX25V8005, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1605, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1605A/MX25L1606E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1605D/MX25L1608D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1635D, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3205(A), 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3205D/MX25L3208D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3206E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L3235D, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6405(D), 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6406E/MX25L6436E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L6445E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25L12805(D), 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25U1635E, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25U3235E/F, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix MX25U6435E/F, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P05-A, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P05, 64 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P10-A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P10, 128 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P20-old, 256 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P40-old, 512 kB: Ignoring RES in favour of RDID. Probing for Micron/Numonyx/ST M25P80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25P128, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M25PX64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST M45PE16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q016, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q032..1E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q032..3E, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q064..1E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q064..3E, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q128..1E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Micron/Numonyx/ST N25Q128..3E, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Nantronics N25S16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD256C, 32 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD512(C), 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD010(C), 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD020(C), 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LD040(C), 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV512(A), 64 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010, 128 kB: Invalid OPCODE 0xab, will not execute. Probing for PMC Pm25LV010A, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC Pm25LV016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo LE25FW203A, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo LE25FW403A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo LE25FW418A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW806, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Sanyo LE25FW808, 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for Spansion S25FL004A, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL008A, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL016A, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL032A/P, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL064A/P, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL204K, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL208K, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL116K/S25FL216K, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Spansion S25FL128S......0, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25LF040A, 512 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25LF080(A), 1024 kB: Invalid OPCODE 0xab, will not execute. Probing for SST SST25VF010, 128 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF016B, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF032B, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF064C, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF040, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF040B, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25VF040B.REMS, 512 kB: Invalid OPCODE 0x90, will not execute. Probing for SST SST25VF080B, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF512, 64 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF010, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF020, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST SST25WF040, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q80.V, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q16.V, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q32.V, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q64.V, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Found Winbond flash chip "W25Q64.V" (8192 kB, SPI) at physical address 0xff800000. Chip status register is 0x80. Probing for Winbond W25Q128.V, 16384 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q20.W, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q40.W, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q80.W, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q16.W, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q32.W, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25Q64.W, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X10, 128 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X20, 256 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X40, 512 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X80, 1024 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X16, 2048 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X32, 4096 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond W25X64, 8192 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Unknown SFDP-capable chip, 0 kB: Invalid OPCODE 0x5a, will not execute. Receiving SFDP signature failed. Probing for AMIC unknown AMIC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Atmel unknown Atmel SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Eon unknown Eon SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Macronix unknown Macronix SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for PMC unknown PMC SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for SST unknown SST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for ST unknown ST SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Sanyo unknown Sanyo SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Winbond unknown Winbond (ex Nexcom) SPI chip, 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Generic unknown SPI chip (RDID), 0 kB: probe_spi_rdid_generic: id1 0xef, id2 0x4017 Probing for Generic unknown SPI chip (REMS), 0 kB: Invalid OPCODE 0x90, will not execute. Probing for Atmel AT49LH002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AB, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 kB: probe_82802ab: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL002, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sharp LHF00L04, 1024 kB: probe_82802ab: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF002A/B, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 kB: probe_jedec_common: id1 0x50, id2 0xb0, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 kB: probe_jedec_common: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 kB: probe_82802ab: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x5f, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040A, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 kB: probe_82802ab: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 kB: probe_82802ab: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 kB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0x5f, id2 0x53, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 kB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 kB: probe_82802ab: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 kB: probe_jedec_common: id1 0x4c, id2 0x41, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 kB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Found Winbond flash chip "W25Q64.V" (8192 kB, SPI). This chip may contain one-time programmable memory. flashrom cannot read and may never be able to write it, hence it may not be able to completely clone the contents of this chip (see man page for details). Block protection is disabled. Reading flash... done. Restoring MMIO space at 0x7ff643ff18a0 Any help/advise/suggestions would be appreciated. My aim was to use flashrom (if possible) to flash some bios other than the chromebook bios. Thanks Sheri

2 3

Help me flash coreboot for extra cash?
by Jonathon Byrd 25 Feb '14

25 Feb '14

I have a Lenovo Yoga 2 Pro with i5 Intel Processor. I hate this UEFI microcrap. Would somebody mind helping me flash this existing BIOS with COREBOOT so that I can put linux on my laptop?   -j

1 0

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom