flashrom April 2011

flashrom@flashrom.org

61 participants
201 discussions

[commit] r1288 - trunk
by repository service 15 Apr '11

15 Apr '11

Author: mkarcher Date: Fri Apr 15 02:03:37 2011 New Revision: 1288 URL: http://flashrom.org/trac/flashrom/changeset/1288 Log: Remove delays in JEDEC erase sequence It is extremely unlikely that a chip not requiring delays in probe does require them in erase. We observed unreliable erasing with a SST49LF004A with these delays, so remove them if the are not required. In review, I got the hint that "probe_jedec goes further by making that call conditional on nonzero delay". I decided to ignore that. For internal_delay, the small amount of clock cycles wasted for calling programmer_delay(0) is negligible compared to LPC cycle times. It might be an issue for 5 wasted bytes on the serial line in serprog. OTOH, flash erase is still slow compared to 6*5 bytes on a serial port at reasonable speed. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/jedec.c Modified: trunk/jedec.c ============================================================================== --- trunk/jedec.c Fri Apr 15 01:43:19 2011 (r1287) +++ trunk/jedec.c Fri Apr 15 02:03:37 2011 (r1288) @@ -242,21 +242,24 @@ unsigned int pagesize, unsigned int mask) { chipaddr bios = flash->virtual_memory; + int delay_us = 0; + if(flash->probe_timing != TIMING_ZERO) + delay_us = 10; /* Issue the Sector Erase command */ chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x80, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x30, bios + page); - programmer_delay(10); + programmer_delay(delay_us); /* wait for Toggle bit ready */ toggle_ready_jedec_slow(bios); @@ -272,21 +275,24 @@ unsigned int blocksize, unsigned int mask) { chipaddr bios = flash->virtual_memory; + int delay_us = 0; + if(flash->probe_timing != TIMING_ZERO) + delay_us = 10; /* Issue the Sector Erase command */ chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x80, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x50, bios + block); - programmer_delay(10); + programmer_delay(delay_us); /* wait for Toggle bit ready */ toggle_ready_jedec_slow(bios); @@ -302,21 +308,24 @@ { int total_size = flash->total_size * 1024; chipaddr bios = flash->virtual_memory; + int delay_us = 0; + if(flash->probe_timing != TIMING_ZERO) + delay_us = 10; /* Issue the JEDEC Chip Erase command */ chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x80, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0xAA, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x55, bios + (0x2AAA & mask)); - programmer_delay(10); + programmer_delay(delay_us); chip_writeb(0x10, bios + (0x5555 & mask)); - programmer_delay(10); + programmer_delay(delay_us); toggle_ready_jedec_slow(bios);

1 0

[commit] r1287 - trunk
by repository service 15 Apr '11

15 Apr '11

Author: mkarcher Date: Fri Apr 15 01:43:19 2011 New Revision: 1287 URL: http://flashrom.org/trac/flashrom/changeset/1287 Log: Remove erase_chip_stm50flw0x0x As the comment indicates, that function is not a chip erase function at all, but a function calling a block eraser in a loop. So it adds no extra value to what we already have in the block_eraser infrastructure. Furthermore, that function assumes a uniform sector size layout, but is referenced from flash chip with non-uniform sector size layout, which is just wrong. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Carl-Daniel Hailfinger <c-d.hailfinger.devel.2006(a)gmx.net> Modified: trunk/chipdrivers.h trunk/flashchips.c trunk/stm50flw0x0x.c Modified: trunk/chipdrivers.h ============================================================================== --- trunk/chipdrivers.h Fri Apr 15 01:14:27 2011 (r1286) +++ trunk/chipdrivers.h Fri Apr 15 01:43:19 2011 (r1287) @@ -128,7 +128,6 @@ /* stm50flw0x0x.c */ int erase_sector_stm50flw0x0x(struct flashchip *flash, unsigned int block, unsigned int blocksize); -int erase_chip_stm50flw0x0x(struct flashchip *flash, unsigned int addr, unsigned int blocklen); int unlock_stm50flw0x0x(struct flashchip *flash); #endif /* !__CHIPDRIVERS_H__ */ Modified: trunk/flashchips.c ============================================================================== --- trunk/flashchips.c Fri Apr 15 01:14:27 2011 (r1286) +++ trunk/flashchips.c Fri Apr 15 01:43:19 2011 (r1287) @@ -6852,9 +6852,6 @@ }, { .eraseblocks = { {64 * 1024, 8}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6887,9 +6884,6 @@ }, { .eraseblocks = { {64 * 1024, 8}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6922,9 +6916,6 @@ }, { .eraseblocks = { {64 * 1024, 16}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6957,9 +6948,6 @@ }, { .eraseblocks = { {64 * 1024, 16}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -6989,9 +6977,6 @@ {16 * 1024, 1}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {256 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7016,9 +7001,6 @@ { .eraseblocks = { {64 * 1024, 32}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {2 * 1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7043,9 +7025,6 @@ { .eraseblocks = { {64 * 1024, 8}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {512 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7070,9 +7049,6 @@ { .eraseblocks = { {64 * 1024, 16}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, @@ -7103,9 +7079,6 @@ {16 * 1024, 1}, }, .block_erase = erase_block_82802ab, - }, { - .eraseblocks = { {2 * 1024 * 1024, 1} }, - .block_erase = erase_chip_stm50flw0x0x, } }, .unlock = unlock_stm50flw0x0x, Modified: trunk/stm50flw0x0x.c ============================================================================== --- trunk/stm50flw0x0x.c Fri Apr 15 01:14:27 2011 (r1286) +++ trunk/stm50flw0x0x.c Fri Apr 15 01:43:19 2011 (r1287) @@ -114,30 +114,3 @@ return 0; } - -/* FIXME: This function is not a real chip erase function. */ -int erase_chip_stm50flw0x0x(struct flashchip *flash, unsigned int addr, unsigned int blocklen) -{ - int i; - int total_size = flash->total_size * 1024; - int page_size = flash->page_size; - - if ((addr != 0) || (blocklen != flash->total_size * 1024)) { - msg_cerr("%s called with incorrect arguments\n", - __func__); - return -1; - } - - for (i = 0; i < total_size / page_size; i++) { - //if (unlock_block_stm50flw0x0x(flash, i * page_size)) { - // msg_cerr("UNLOCK FAILED!\n"); - // return -1; - //} - if (erase_block_82802ab(flash, i * page_size, page_size)) { - msg_cerr("ERASE FAILED!\n"); - return -1; - } - } - - return 0; -}

1 0

[commit] r1286 - trunk
by repository service 15 Apr '11

15 Apr '11

Author: mkarcher Date: Fri Apr 15 01:14:27 2011 New Revision: 1286 URL: http://flashrom.org/trac/flashrom/changeset/1286 Log: Board enable for Foxconn 6150K8MD-8EKRSH Reported by: wickberg(a)student.chalmers.se flashrom -V: http://paste.flashrom.org/view.php?id=452 lspci: http://paste.flashrom.org/view.php?id=453 (note that the flashrom dump is with a foreign chip. That board is originally equipped with an PMC Pm49FL004. Signed-off-by: Michael Karcher <flashrom(a)mkarcher.dialup.fu-berlin.de> Acked-by: Stefan Reinauer <stefan.reinauer(a)coreboot.org> Modified: trunk/board_enable.c trunk/print.c Modified: trunk/board_enable.c ============================================================================== --- trunk/board_enable.c Sat Apr 2 13:47:21 2011 (r1285) +++ trunk/board_enable.c Fri Apr 15 01:14:27 2011 (r1286) @@ -940,6 +940,7 @@ /* * Suited for: + * - Foxconn 6150K8MD-8EKRSH: Socket 939 + NVIDIA MCP51 * - MSI K8N Neo4: NVIDIA CK804. TODO: Should probably be K8N Neo4 Platinum, see http://www.coreboot.org/pipermail/flashrom/2010-August/004362.html. * - MSI K8NGM2-L: NVIDIA MCP51 */ @@ -1954,6 +1955,7 @@ {0x10DE, 0x005E, 0x1695, 0x1010, 0x10DE, 0x0050, 0x1695, 0x1010, NULL, NULL, NULL, "EPoX", "EP-8NPA7I", 0, OK, nvidia_mcp_gpio4_raise}, {0x10EC, 0x8139, 0x1695, 0x9001, 0x11C1, 0x5811, 0x1695, 0x9015, NULL, NULL, NULL, "EPoX", "EP-8RDA3+", 0, OK, nvidia_mcp_gpio31_raise}, {0x8086, 0x7110, 0, 0, 0x8086, 0x7190, 0, 0, NULL, "epox", "ep-bx3", "EPoX", "EP-BX3", 0, NT, intel_piix4_gpo22_raise}, + {0x10de, 0x02f0, 0x105b, 0x0d01, 0x10de, 0x0264, 0x105b, 0x0d01, NULL, NULL, NULL, "Foxconn", "6150K8MD-8EKRSH", 0, NT, nvidia_mcp_gpio2_raise}, {0x8086, 0x2443, 0x8086, 0x2442, 0x8086, 0x1130, 0x8086, 0x1130, "^6IEM ", NULL, NULL, "GIGABYTE", "GA-6IEM", 0, NT, intel_ich_gpio25_raise}, {0x1106, 0x0686, 0x1106, 0x0686, 0x1106, 0x3058, 0x1458, 0xa000, NULL, NULL, NULL, "GIGABYTE", "GA-7ZM", 512, OK, NULL}, {0x8086, 0x244b, 0x8086, 0x2442, 0x8086, 0x2445, 0x1458, 0xa002, NULL, NULL, NULL, "GIGABYTE", "GA-8IRML", 0, OK, intel_ich_gpio25_raise}, Modified: trunk/print.c ============================================================================== --- trunk/print.c Sat Apr 2 13:47:21 2011 (r1285) +++ trunk/print.c Fri Apr 15 01:14:27 2011 (r1286) @@ -462,6 +462,7 @@ B("EPoX", "EP-BX3", 1, "http://www.epox.com/product.asp?ID=EP-BX3", NULL), B("EVGA", "132-CK-NF78", 1, "http://http://www.evga.com/articles/385.asp", NULL), B("FIC", "VA-502", 0, "ftp://ftp.fic.com.tw/motherboard/manual/socket7/va-502/", "No public report found. Owned by Uwe Hermann <uwe(a)hermann-uwe.de>. Seems the PCI subsystem IDs are identical with the Tekram P6Pro-A5. May work now."), + B("Foxconn", "6150K8MD-8EKRSH", 1, "http://www.foxconnchannel.com/product/motherboards/detail_overview.aspx?id=…", NULL), B("Foxconn", "A6VMX", 1, "http://www.foxconnchannel.com/product/motherboards/detail_overview.aspx?id=…", NULL), B("Fujitsu-Siemens", "ESPRIMO P5915", 1, "http://uk.ts.fujitsu.com/rl/servicesupport/techsupport/professionalpc/ESPRI…", "Mainboard model is D2312-A2."), B("GIGABYTE", "GA-2761GXDK", 1, "http://www.computerbase.de/news/hardware/mainboards/amd-systeme/2007/mai/gi…", NULL),

1 0

Fw: FAILED: Abit nf-m2-nView
by Stefan Tauner 13 Apr '11

13 Apr '11

hello guntram! i am glad to hear that it worked. can you please mail us the complete log of sudo flashrom -Vw abit_093.bin -p internal:boardenable=force so that we can verify that and mark this board as tested. thanks! Begin forwarded message: Date: Wed, 13 Apr 2011 11:34:47 +0200 From: Guntram Schmidt <guntram.schmidt(a)googlemail.com> To: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> Subject: Re: [flashrom] FAILED: Abit nf-m2-nView Hello again! It worked with the "-p internal:boardenable=force" ! So you may regard the mainboard specific code of the Abit nf-m2-nView as tested, now! Thanks a lot, Guntram PS: Unfortunately, the BIOS update didn't solve my problem of CPU-fan not starting...but this may now be a hardware related problem ... Am 13.04.2011 00:32, schrieb Stefan Tauner: > On Tue, 12 Apr 2011 22:14:16 +0200 > Guntram Schmidt<guntram.schmidt(a)googlemail.com> wrote: > >> I first wanted simply to write the saved BIOS again, to be sure, >> everything works fine before flashing the new version of the bios. >> To be honest: I could'nt figure out the meaning concerning the >> "mainboard-specific code", that's why I tried nevertheless. > > hello > > please retry with "-p internal:boardenable=force" added to your > command and report back, thanks. > > disclamer: i read that manpage section the first time 2 minutes > ago. :) -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner

1 0

FAILED: Abit nf-m2-nView
by Guntram Schmidt 13 Apr '11

13 Apr '11

Hi folks, I wanted to reflash the just-before-backupped BIOS with self-compiled Flashform 0.9.3 on Ubuntu Karmic Koala (9.10) 32-Bit, PAE-Kernel 2.6.31-22. This is the message I got: $ sudo flashrom -w abit_093.bin flashrom v0.9.3-r1205 on Linux 2.6.31-22-generic-pae (i686), built with libpci 3.0.0, GCC 4.4.1, little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found chipset "NVIDIA MCP51", enabling flash write... OK. This chipset supports the following protocols: Non-SPI. WARNING: Your mainboard is abit NF-M2 nView, but the mainboard-specific code has not been tested, and thus will not not be executed by default. Depending on your hardware environment, erasing, writing or even probing can fail without running the board specific code. Please see the man page (section PROGRAMMER SPECIFIC INFO, subsection "internal programmer") for details. Found chip "PMC Pm49FL004" (512 KB, LPC,FWH) at physical address 0xfff80000. Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash chip... ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x00000fff: 0x70f ERASE FAILED! ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0000ffff: 0x70f ERASE FAILED! ERASE FAILED at 0x00000000! Expected=0xff, Read=0x49, failed byte count from 0x00000000-0x0007ffff: 0x5973f ERASE FAILED! FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org with FAILED: your board name in the subject line! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! I first wanted simply to write the saved BIOS again, to be sure, everything works fine before flashing the new version of the bios. To be honest: I could'nt figure out the meaning concerning the "mainboard-specific code", that's why I tried nevertheless. Thanks for any hints on how to continue, Guntram

2 2

Flashrom on MSI X58 Pro-E MS-7522 erase failed!
by Антон Кочков 12 Apr '11

12 Apr '11

Good day! http://paste.flashrom.org/view.php?id=476 http://paste.flashrom.org/view.php?id=477 Best regards, Anton Kochkov.

1 1

Fwd: HELP! "...flash chip is in an unknown state"
by Idwer Vollering 12 Apr '11

12 Apr '11

Forwarding the attachment. ---------- Forwarded message ---------- From: Bernard Matthews <philoscience(a)gmail.com> Date: 2011/4/12 Subject: Re: [flashrom] HELP! "...flash chip is in an unknown state" To: Idwer Vollering <vidwer(a)gmail.com> It gets weirder - when redirecting the output to a file, with "sudo flashrom -V -w flashbackup.rom > output.txt", it works fine. I see that: "Chip status register is 00", and: Chip status register: Bit 4 / Block Protect 2 (BP2) is not set Chip status register: Bit 3 / Block Protect 1 (BP1) is not set Chip status register: Bit 2 / Block Protect 0 (BP0) is not set but in output.txt, but when the output goes straight to the xterm, those registers are set, and: "Chip status register is 1c". What follows is a multiscreen manual cut and paste. ============================================================== grml@grml ~ % sudo flashrom -V -w flashbackup.rom flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OS timer resolution is 1 usecs, 1450M loops per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, 10000 myus = 10009 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. DMI string system-manufacturer: "BIOSTAR Group" DMI string system-product-name: "TA785G3" DMI string system-version: " " DMI string baseboard-manufacturer: "BIOSTAR Group" DMI string baseboard-product-name: "TA785G3" DMI string baseboard-version: " " DMI string chassis-type: "Desktop" Found ITE Super I/O, id 8718 Found chipset "AMD SB700/SB710/SB750", enabling flash write... chipset PCI ID is 1002:439d, SPI base address is at 0xfec10000 AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 SpiArbEnable=1, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, ArbWaitCount=4, SpiBridgeDisable=1, DropOneClkOnRd=0 GPIO11 used for SPI_DO GPIO12 used for SPI_DI GPIO31 used for SPI_HOLD GPIO32 used for SPI_CS GPIO47 used for SPI_CLK ROM strap override is not active OK. This chipset supports the following protocols: LPC,FWH,SPI. No IT87* serial flash segment enabled. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for AMIC A25L05PT, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L05PU, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PT, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L10PU, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PT, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L20PU, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L80P, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PT, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L16PU, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L080, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L016, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25L032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A25LQ032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ASD AE49F2008, 256 KB: skipped. Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25DQ161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F020, 256 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for EMST F25L008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon EN29F010, 128 KB: skipped. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Hyundai HY29F002T, 256 KB: skipped. Probing for Hyundai HY29F002B, 256 KB: skipped. Probing for Intel 28F001BX-B, 128 KB: skipped. Probing for Intel 28F001BX-T, 128 KB: skipped. Probing for Intel 28F002BC-T, 256 KB: skipped. Probing for Intel 28F004S5, 512 KB: skipped. Probing for Intel 28F004BV/BE-B, 512 KB: skipped. Probing for Intel 28F004BV/BE-T, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Chip status register is 1c Chip status register: Status Register Write Disable (SRWD) is not set Chip status register: Bit 6 is not set Chip status register: Bit 5 / Block Protect 3 (BP3) is not set Chip status register: Bit 4 / Block Protect 2 (BP2) is set Chip status register: Bit 3 / Block Protect 1 (BP1) is set Chip status register: Bit 2 / Block Protect 0 (BP0) is set Chip status register: Write Enable Latch (WEL) is not set Chip status register: Write In Progress (WIP/BUSY) is not set Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF064C, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST25LF040A.RES, 512 KB: probe_spi_res2: id1 0x13, id2 0x13 Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x64, id2 0xe6, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BB, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25Q64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Winbond W29C011, 128 KB: skipped. Probing for Winbond W29C020C, 256 KB: skipped. Probing for Winbond W29C040P, 512 KB: skipped. Probing for Winbond W29EE011, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49F002U, 256 KB: skipped. Probing for Winbond W49F020, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xc9, id2 0x98, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct probe timing information, using default 10mS/40uS. probe_jedec_common: id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Atmel unknown Atmel SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Eon unknown Eon SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Macronix unknown Macronix SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Sanyo unknown Sanyo SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (RDID), 0 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 0xc2, id2 0x13 Some block protection in effect, disabling Missing status register write definition, assuming EWSR is needed Block protection could not be disabled! Flash image seems to be a legacy BIOS. Disabling checks. Writing flash chip... Erasing flash before programming... Erasing flash chip... Looking at blockwise erase function 0... trying... 0x000000-0x000fff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x00000fff: 0xf9d ERASE FAILED! Looking at blockwise erase function 1... trying... 0x000000-0x00ffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x0000ffff: 0xf8f7 ERASE FAILED! Looking at blockwise erase function 2... trying... 0x000000-0x00ffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x0000ffff: 0xf8f7 ERASE FAILED! Looking at blockwise erase function 3... trying... 0x000000-0x0fffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x000fffff: 0xe05b5 ERASE FAILED! Looking at blockwise erase function 4... trying... 0x000000-0x0fffff, ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte count from 0x00000000-0x000fffff: 0xe05b5 ERASE FAILED! Looking at blockwise erase function 5... not defined. Looking for another erase function. FAILED! ERASE FAILED! FAILED! Your flash chip is in an unknown state. Get help on IRC at irc.freenode.net (channel #flashrom) or mail flashrom(a)flashrom.org! ------------------------------------------------------------------------------- DO NOT REBOOT OR POWEROFF! sudo flashrom -V -w flashbackup.rom 8.37s user 0.07s system 99% cpu 8.468 total grml@grml ~ % sudo flashrom -v flashbackup.rom flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, id 8718 Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Flash image seems to be a legacy BIOS. Disabling checks. Verifying flash... VERIFIED. grml@grml ~ % sudo flashrom -V -w flashbackup.rom > output.txt sudo flashrom -V -w flashbackup.rom > output.txt 54.05s user 0.06s system 99% cpu 54.152 total grml@grml ~ % ls -l total 1060 -rw-r--r-- 1 root root 1048576 2011-04-12 17:54 flashbackup.rom -rw-rw-r-- 1 grml grml 28644 2011-04-12 17:56 output.txt grml@grml ~ % sudo flashrom -v flashbackup.rom flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian flashrom is free software, get the source code at http://www.flashrom.org Calibrating delay loop... OK. No coreboot table found. Found ITE Super I/O, id 8718 Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. This chipset supports the following protocols: LPC,FWH,SPI. Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. Flash image seems to be a legacy BIOS. Disabling checks. Verifying flash... VERIFIED. grml@grml ~ % ============================================================== And attached to this email is the file output.txt. Also, I am using the liveCD version of GRML, debian-based. Hope this helps! ----- bernard On Tue, Apr 12, 2011 at 5:52 PM, Bernard Matthews <philoscience(a)gmail.com> wrote: > Since I know it will work now, I will be happy to try and reflash it > per your instructions so we can see what is happening. > > Give me several minutes, and I will email the output to you. > > Thank you again! > > ----- bernard > > On Tue, Apr 12, 2011 at 5:44 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>> Thank you very, very much for getting in touch with me! >>> >>> I solved the problem before I got your email, but didn't have a chance >>> to email an update yet. >>> >>> On my system, it appears flashrom cannot be run from an Xterm window. >>> If that is in the documentation somewhere, I apologize for missing it. >> >> No, it's not. This sounds weird. >> >>> >>> I first verified with "flashrom -v 88GAP901_BST_20110411.BST" that >>> the image currently in the rom matched my backup file, in case I had >>> to reboot. >>> >>> I cannot recall if I did reboot first, or if I had just closed X windows. >>> >>> Using flashrom from a text terminal CLI worked perfectly! I see the >>> new file and date on my boot screen now, and so far no problems. >>> >>> Thank you folks very much for such a wonderful program. >>> >>> ----- bernard >>> >>> On Tue, Apr 12, 2011 at 2:16 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>>> Hi Help, >>>>> >>>>> I thought I did what was right, but apparently I'm missing something. >>>>> >>>>> System details: >>>>> >>>>> BioStar TA785G3 v 6.1 according to the printing on the mainboard. >>>>> >>>>> Athlon II X3 435. >>>>> >>>>> Label on factory CMOS: 88GAP901BST. But the date showing on boot is 3/31/2010. >>>>> >>>>> I'm trying to replace the CMOS info because of an intermittent board >>>>> failure that I felt I had reduced to either a processor failure or a >>>>> board failure. >>>>> >>>>> The mainboard comes with a built-in utility on F12 to flash the new >>>>> file, but it rejects the file claiming that the BIOS ID does not >>>>> match. >>>>> >>>>> The new file came from Biostar. I actually downloaded two copies, one >>>>> from Taiwan, and one from USA, and diff'd them to make sure they were >>>>> the same. >>>>> >>>>> So below are the results of my attempt to flash the chip :-(. >>>>> >>>>> >>>>> Here's my initial run to check for compatibility with my board (blank >>>>> spaces/lines added for legibility) >>>>> ============================================================== >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> No operations were specified. >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom -r 88GAP901_BST_20110411.BST >>>> >>>> This is your backup file... >>>> >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Reading flash... done. >>>>> >>>>> ============================================================== >>>>> >>>>> At this point, I did a Google search for "Block protection could not >>>>> be disabled", but did not find anything that said THIS MEANS YOU WON'T >>>>> BE ABLE TO ERASE! >>>>> >>>>> So, I forged ahead: >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % ls -l *BST >>>>> >>>>> -r--r--r-- 1 root root 1048576 2011-04-12 05:57 88GAP901_BST_20110411.BST >>>>> grml@grml /mnt/2011_home/netvista % cd Down* >>>>> >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % ls -l *BST >>>>> >>>>> -r--r--r-- 1 grml users 1048576 2011-04-10 07:43 88GAP804.BST >>>>> >>>>> ============================================================== >>>>> >>>>> The above lines show that the file that I'm going to write with >>>>> (88GAP804.BST) is the same size as the one that I saved from the chip >>>>> (88GAP901_BST_20110411.BST). >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % sudo flashrom -w 88GAP804.BST >>>> >>>> and this is the new file. >>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Flash image seems to be a legacy BIOS. Disabling checks. >>>>> Writing flash chip... Erasing flash before programming... Erasing flash chip... >>>>> >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x00000fff: 0xf9d >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> FAILED! >>>>> ERASE FAILED! >>>>> FAILED! >>>>> Your flash chip is in an unknown state. >>>>> Get help on IRC at irc.freenode.net (channel #flashrom) or >>>>> mail flashrom(a)flashrom.org! >>>>> ------------------------------------------------------------------------------- >>>>> DO NOT REBOOT OR POWEROFF! >>>> >>>> Can you re-run flashrom like above, but with the "-V" (--verbose) parameter ? >>>> Like this: sudo flashrom -V -w 88GAP804.BST >>>> >>>>> sudo flashrom -w 88GAP804.BST 8.37s user 0.07s system 99% cpu 8.489 total >>>>> >>>>> ============================================================== >>>>> >>>>> So, since the erase failed, shouldn't I be okay? Unless my cats press >>>>> a button or pull a wire, I will leave the machine on for a response. >>>>> >>>>> Thank you very much for your help in advance! >>>>> >>>>> ----- bernard >>>>> >>>>> _______________________________________________ >>>>> flashrom mailing list >>>>> flashrom(a)flashrom.org >>>>> http://www.flashrom.org/mailman/listinfo/flashrom >>>>> >>>> >>> >> >

2 1

Re: [flashrom] HELP! "...flash chip is in an unknown state"
by Idwer Vollering 12 Apr '11

12 Apr '11

Use "reply to all". Thanks. 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: > It gets weirder - when redirecting the output to a file, with "sudo > flashrom -V -w flashbackup.rom > output.txt", it works fine. > > I see that: > > "Chip status register is 00", and: > > Chip status register: Bit 4 / Block Protect 2 (BP2) is not set > Chip status register: Bit 3 / Block Protect 1 (BP1) is not set > Chip status register: Bit 2 / Block Protect 0 (BP0) is not set > > but in output.txt, but when the output goes straight to the xterm, > those registers are set, and: > > "Chip status register is 1c". > > What follows is a multiscreen manual cut and paste. > > ============================================================== > grml@grml ~ % sudo flashrom -V -w flashbackup.rom > flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci > 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OS timer resolution is 1 usecs, 1450M loops > per second, 10 myus = 10 us, 100 myus = 100 us, 1000 myus = 999 us, > 10000 myus = 10009 us, 4 myus = 5 us, OK. > Initializing internal programmer > No coreboot table found. > DMI string system-manufacturer: "BIOSTAR Group" > DMI string system-product-name: "TA785G3" > DMI string system-version: " " > DMI string baseboard-manufacturer: "BIOSTAR Group" > DMI string baseboard-product-name: "TA785G3" > DMI string baseboard-version: " " > DMI string chassis-type: "Desktop" > Found ITE Super I/O, id 8718 > Found chipset "AMD SB700/SB710/SB750", enabling flash write... chipset > PCI ID is 1002:439d, SPI base address is at 0xfec10000 > AltSpiCSEnable=0, SpiRomEnable=1, AbortEnable=0 > PrefetchEnSPIFromIMC=0, PrefetchEnSPIFromHost=1, SpiOpEnInLpcMode=1 > SpiArbEnable=1, SpiAccessMacRomEn=1, SpiHostAccessRomEn=1, > ArbWaitCount=4, SpiBridgeDisable=1, DropOneClkOnRd=0 > GPIO11 used for SPI_DO > GPIO12 used for SPI_DI > GPIO31 used for SPI_HOLD > GPIO32 used for SPI_CS > GPIO47 used for SPI_CLK > ROM strap override is not active > OK. > This chipset supports the following protocols: LPC,FWH,SPI. > No IT87* serial flash segment enabled. > Probing for AMD Am29F010A/B, 128 KB: skipped. > Probing for AMD Am29F002(N)BB, 256 KB: skipped. > Probing for AMD Am29F002(N)BT, 256 KB: skipped. > Probing for AMD Am29F016D, 2048 KB: skipped. > Probing for AMD Am29F040B, 512 KB: skipped. > Probing for AMD Am29F080B, 1024 KB: skipped. > Probing for AMD Am29LV040B, 512 KB: skipped. > Probing for AMD Am29LV081B, 1024 KB: skipped. > Probing for AMIC A25L05PT, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L05PU, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L10PT, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L10PU, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L20PT, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L20PU, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L80P, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L16PT, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L16PU, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L080, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L016, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25L032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A25LQ032, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for AMIC A29002B, 256 KB: skipped. > Probing for AMIC A29002T, 256 KB: skipped. > Probing for AMIC A29040B, 512 KB: skipped. > Probing for AMIC A49LF040A, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for ASD AE49F2008, 256 KB: skipped. > Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF081A, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25DQ161, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Atmel AT29C512, 64 KB: skipped. > Probing for Atmel AT29C010A, 128 KB: skipped. > Probing for Atmel AT29C020, 256 KB: skipped. > Probing for Atmel AT29C040A, 512 KB: skipped. > Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Atmel AT49BV512, 64 KB: skipped. > Probing for Atmel AT49F020, 256 KB: skipped. > Probing for Atmel AT49F002(N), 256 KB: skipped. > Probing for Atmel AT49F002(N)T, 256 KB: skipped. > Probing for EMST F49B002UA, 256 KB: skipped. > Probing for EMST F25L008A, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon EN29F010, 128 KB: skipped. > Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. > Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. > Probing for Fujitsu MBM29F004BC, 512 KB: skipped. > Probing for Fujitsu MBM29F004TC, 512 KB: skipped. > Probing for Fujitsu MBM29F400BC, 512 KB: skipped. > Probing for Fujitsu MBM29F400TC, 512 KB: skipped. > Probing for Hyundai HY29F002T, 256 KB: skipped. > Probing for Hyundai HY29F002B, 256 KB: skipped. > Probing for Intel 28F001BX-B, 128 KB: skipped. > Probing for Intel 28F001BX-T, 128 KB: skipped. > Probing for Intel 28F002BC-T, 256 KB: skipped. > Probing for Intel 28F004S5, 512 KB: skipped. > Probing for Intel 28F004BV/BE-B, 512 KB: skipped. > Probing for Intel 28F004BV/BE-T, 512 KB: skipped. > Probing for Intel 28F400BV/CV/CE-B, 512 KB: skipped. > Probing for Intel 28F400BV/CV/CE-T, 512 KB: skipped. > Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Chip status register is 1c > Chip status register: Status Register Write Disable (SRWD) is not set > Chip status register: Bit 6 is not set > Chip status register: Bit 5 / Block Protect 3 (BP3) is not set > Chip status register: Bit 4 / Block Protect 2 (BP2) is set > Chip status register: Bit 3 / Block Protect 1 (BP1) is set > Chip status register: Bit 2 / Block Protect 0 (BP0) is set > Chip status register: Write Enable Latch (WEL) is not set > Chip status register: Write In Progress (WIP/BUSY) is not set > Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. > Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Macronix MX29F001B, 128 KB: skipped. > Probing for Macronix MX29F001T, 128 KB: skipped. > Probing for Macronix MX29F002B, 256 KB: skipped. > Probing for Macronix MX29F002T, 256 KB: skipped. > Probing for Macronix MX29LV040, 512 KB: skipped. > Probing for MoselVitelic V29C51000B, 64 KB: skipped. > Probing for MoselVitelic V29C51000T, 64 KB: skipped. > Probing for MoselVitelic V29C51400B, 512 KB: skipped. > Probing for MoselVitelic V29C51400T, 512 KB: skipped. > Probing for MoselVitelic V29LC51000, 64 KB: skipped. > Probing for MoselVitelic V29LC51001, 128 KB: skipped. > Probing for MoselVitelic V29LC51002, 256 KB: skipped. > Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC Pm29F002T, 256 KB: skipped. > Probing for PMC Pm29F002B, 256 KB: skipped. > Probing for PMC Pm39LV010, 128 KB: skipped. > Probing for PMC Pm39LV020, 256 KB: skipped. > Probing for PMC Pm39LV040, 512 KB: skipped. > Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xc9, id2 > 0x98, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF064C, 8192 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 > Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for SST SST25LF040A.RES, 512 KB: probe_spi_res2: id1 0x13, id2 0x13 > Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xc2, id2 0x13 > Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for SST SST28SF040A, 512 KB: skipped. > Probing for SST SST29EE010, 128 KB: skipped. > Probing for SST SST29LE010, 128 KB: skipped. > Probing for SST SST29EE020A, 256 KB: skipped. > Probing for SST SST29LE020, 256 KB: skipped. > Probing for SST SST39SF512, 64 KB: skipped. > Probing for SST SST39SF010A, 128 KB: skipped. > Probing for SST SST39SF020A, 256 KB: skipped. > Probing for SST SST39SF040, 512 KB: skipped. > Probing for SST SST39VF512, 64 KB: skipped. > Probing for SST SST39VF010, 128 KB: skipped. > Probing for SST SST39VF020, 256 KB: skipped. > Probing for SST SST39VF040, 512 KB: skipped. > Probing for SST SST39VF080, 1024 KB: skipped. > Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xc9, > id2 0x98, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x64, > id2 0xe6, id1 is normal flash content, id2 is normal flash content > Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, > id2 0xff, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF016C, 2048 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF020, 256 KB: probe_jedec_common: id1 0xc9, id2 > 0x98, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF020A, 256 KB: probe_jedec_common: id1 0xc9, id2 > 0x98, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF040, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF040B, 512 KB: probe_jedec_common: id1 0x0a, id2 > 0x91, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for SST SST49LF080A, 1024 KB: Chip lacks correct probe timing > information, using default 10mS/40uS. probe_jedec_common: id1 0xff, > id2 0xff, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for SST SST49LF160C, 2048 KB: probe_82802ab: id1 0xff, id2 > 0xff, id1 parity violation, id1 is normal flash content, id2 is normal > flash content > Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. > Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. > Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. > Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for ST M29F002B, 256 KB: skipped. > Probing for ST M29F002T/NT, 256 KB: skipped. > Probing for ST M29F040B, 512 KB: skipped. > Probing for ST M29F400BB, 512 KB: skipped. > Probing for ST M29F400BT, 512 KB: skipped. > Probing for ST M29W010B, 128 KB: skipped. > Probing for ST M29W040B, 512 KB: skipped. > Probing for ST M29W512B, 64 KB: skipped. > Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xc9, id2 0x98, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW016, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0x0a, id2 0x91, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for ST M50LPW116, 2048 KB: probe_82802ab: id1 0xff, id2 0xff, > id1 parity violation, id1 is normal flash content, id2 is normal flash > content > Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. > Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. > Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. > Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. > Probing for TI TMS29F002RB, 256 KB: skipped. > Probing for TI TMS29F002RT, 256 KB: skipped. > Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25Q64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xc2, > id2 0x2014 > Probing for Winbond W29C011, 128 KB: skipped. > Probing for Winbond W29C020C, 256 KB: skipped. > Probing for Winbond W29C040P, 512 KB: skipped. > Probing for Winbond W29EE011, 128 KB: skipped. > Probing for Winbond W39V040A, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V040B, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V040C, 512 KB: Chip lacks correct probe timing > information, using default 10mS/40uS. probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0x0a, > id2 0x91, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V080A, 1024 KB: probe_jedec_common: id1 0xff, > id2 0xff, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W49F002U, 256 KB: skipped. > Probing for Winbond W49F020, 256 KB: skipped. > Probing for Winbond W49V002A, 256 KB: probe_jedec_common: id1 0xc9, > id2 0x98, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xc9, > id2 0x98, id1 parity violation, id1 is normal flash content, id2 is > normal flash content > Probing for Winbond W39V080FA, 1024 KB: Chip lacks correct probe > timing information, using default 10mS/40uS. probe_jedec_common: id1 > 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 > is normal flash content > Probing for Winbond W39V080FA (dual mode), 512 KB: Chip lacks correct > probe timing information, using default 10mS/40uS. probe_jedec_common: > id1 0x0a, id2 0x91, id1 parity violation, id1 is normal flash content, > id2 is normal flash content > Probing for AMIC unknown AMIC SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for Atmel unknown Atmel SPI chip, 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Eon unknown Eon SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for Macronix unknown Macronix SPI chip, 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: > id1 0xc2, id2 0x2014 > Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 > 0xc2, id2 0x2014 > Probing for Sanyo unknown Sanyo SPI chip, 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Generic unknown SPI chip (RDID), 0 KB: > probe_spi_rdid_generic: id1 0xc2, id2 0x2014 > Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 > 0xc2, id2 0x13 > Some block protection in effect, disabling > Missing status register write definition, assuming EWSR is needed > Block protection could not be disabled! > Flash image seems to be a legacy BIOS. Disabling checks. > Writing flash chip... Erasing flash before programming... Erasing > flash chip... Looking at blockwise erase function 0... trying... > 0x000000-0x000fff, ERASE FAILED at 0x0000000c! Expected=0xff, > Read=0x0c, failed byte count from 0x00000000-0x00000fff: 0xf9d > ERASE FAILED! > > Looking at blockwise erase function 1... trying... 0x000000-0x00ffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x0000ffff: 0xf8f7 > ERASE FAILED! > > Looking at blockwise erase function 2... trying... 0x000000-0x00ffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x0000ffff: 0xf8f7 > ERASE FAILED! > > Looking at blockwise erase function 3... trying... 0x000000-0x0fffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x000fffff: 0xe05b5 > ERASE FAILED! > > Looking at blockwise erase function 4... trying... 0x000000-0x0fffff, > ERASE FAILED at 0x0000000c! Expected=0xff, Read=0x0c, failed byte > count from 0x00000000-0x000fffff: 0xe05b5 > ERASE FAILED! > > Looking at blockwise erase function 5... not defined. Looking for > another erase function. > FAILED! > ERASE FAILED! > FAILED! > Your flash chip is in an unknown state. > Get help on IRC at irc.freenode.net (channel #flashrom) or > mail flashrom(a)flashrom.org! > ------------------------------------------------------------------------------- > DO NOT REBOOT OR POWEROFF! > sudo flashrom -V -w flashbackup.rom 8.37s user 0.07s system 99% cpu 8.468 total > > grml@grml ~ % sudo flashrom -v flashbackup.rom > > flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci > 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OK. > No coreboot table found. > Found ITE Super I/O, id 8718 > Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. > This chipset supports the following protocols: LPC,FWH,SPI. > Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. > Flash image seems to be a legacy BIOS. Disabling checks. > Verifying flash... VERIFIED. > > grml@grml ~ % sudo flashrom -V -w flashbackup.rom > output.txt > > sudo flashrom -V -w flashbackup.rom > output.txt 54.05s user 0.06s > system 99% cpu 54.152 total > > grml@grml ~ % ls -l > total 1060 > -rw-r--r-- 1 root root 1048576 2011-04-12 17:54 flashbackup.rom > -rw-rw-r-- 1 grml grml 28644 2011-04-12 17:56 output.txt > > grml@grml ~ % sudo flashrom -v flashbackup.rom > > flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci > 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian > flashrom is free software, get the source code at http://www.flashrom.org > > Calibrating delay loop... OK. > No coreboot table found. > Found ITE Super I/O, id 8718 > Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. > This chipset supports the following protocols: LPC,FWH,SPI. > Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. > Flash image seems to be a legacy BIOS. Disabling checks. > Verifying flash... VERIFIED. > grml@grml ~ % > ============================================================== > > And attached to this email is the file output.txt. > > Also, I am using the liveCD version of GRML, debian-based. > > Hope this helps! > > ----- bernard > > On Tue, Apr 12, 2011 at 5:52 PM, Bernard Matthews > <philoscience(a)gmail.com> wrote: >> Since I know it will work now, I will be happy to try and reflash it >> per your instructions so we can see what is happening. >> >> Give me several minutes, and I will email the output to you. >> >> Thank you again! >> >> ----- bernard >> >> On Tue, Apr 12, 2011 at 5:44 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>> Thank you very, very much for getting in touch with me! >>>> >>>> I solved the problem before I got your email, but didn't have a chance >>>> to email an update yet. >>>> >>>> On my system, it appears flashrom cannot be run from an Xterm window. >>>> If that is in the documentation somewhere, I apologize for missing it. >>> >>> No, it's not. This sounds weird. >>> >>>> >>>> I first verified with "flashrom -v 88GAP901_BST_20110411.BST" that >>>> the image currently in the rom matched my backup file, in case I had >>>> to reboot. >>>> >>>> I cannot recall if I did reboot first, or if I had just closed X windows. >>>> >>>> Using flashrom from a text terminal CLI worked perfectly! I see the >>>> new file and date on my boot screen now, and so far no problems. >>>> >>>> Thank you folks very much for such a wonderful program. >>>> >>>> ----- bernard >>>> >>>> On Tue, Apr 12, 2011 at 2:16 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>>>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>>>> Hi Help, >>>>>> >>>>>> I thought I did what was right, but apparently I'm missing something. >>>>>> >>>>>> System details: >>>>>> >>>>>> BioStar TA785G3 v 6.1 according to the printing on the mainboard. >>>>>> >>>>>> Athlon II X3 435. >>>>>> >>>>>> Label on factory CMOS: 88GAP901BST. But the date showing on boot is 3/31/2010. >>>>>> >>>>>> I'm trying to replace the CMOS info because of an intermittent board >>>>>> failure that I felt I had reduced to either a processor failure or a >>>>>> board failure. >>>>>> >>>>>> The mainboard comes with a built-in utility on F12 to flash the new >>>>>> file, but it rejects the file claiming that the BIOS ID does not >>>>>> match. >>>>>> >>>>>> The new file came from Biostar. I actually downloaded two copies, one >>>>>> from Taiwan, and one from USA, and diff'd them to make sure they were >>>>>> the same. >>>>>> >>>>>> So below are the results of my attempt to flash the chip :-(. >>>>>> >>>>>> >>>>>> Here's my initial run to check for compatibility with my board (blank >>>>>> spaces/lines added for legibility) >>>>>> ============================================================== >>>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom >>>>>> >>>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>>> >>>>>> Calibrating delay loop... OK. >>>>>> No coreboot table found. >>>>>> Found ITE Super I/O, id 8718 >>>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>>> No operations were specified. >>>>>> ============================================================== >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom -r 88GAP901_BST_20110411.BST >>>>> >>>>> This is your backup file... >>>>> >>>>>> >>>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>>> >>>>>> Calibrating delay loop... OK. >>>>>> No coreboot table found. >>>>>> Found ITE Super I/O, id 8718 >>>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>>> Block protection could not be disabled! >>>>>> Reading flash... done. >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> At this point, I did a Google search for "Block protection could not >>>>>> be disabled", but did not find anything that said THIS MEANS YOU WON'T >>>>>> BE ABLE TO ERASE! >>>>>> >>>>>> So, I forged ahead: >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista % ls -l *BST >>>>>> >>>>>> -r--r--r-- 1 root root 1048576 2011-04-12 05:57 88GAP901_BST_20110411.BST >>>>>> grml@grml /mnt/2011_home/netvista % cd Down* >>>>>> >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista/Downloads % ls -l *BST >>>>>> >>>>>> -r--r--r-- 1 grml users 1048576 2011-04-10 07:43 88GAP804.BST >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> The above lines show that the file that I'm going to write with >>>>>> (88GAP804.BST) is the same size as the one that I saved from the chip >>>>>> (88GAP901_BST_20110411.BST). >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> grml@grml /mnt/2011_home/netvista/Downloads % sudo flashrom -w 88GAP804.BST >>>>> >>>>> and this is the new file. >>>>> >>>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>>> >>>>>> Calibrating delay loop... OK. >>>>>> No coreboot table found. >>>>>> Found ITE Super I/O, id 8718 >>>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>>> Block protection could not be disabled! >>>>>> Flash image seems to be a legacy BIOS. Disabling checks. >>>>>> Writing flash chip... Erasing flash before programming... Erasing flash chip... >>>>>> >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x00000fff: 0xf9d >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>>> ERASE FAILED! >>>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>>> ERASE FAILED! >>>>>> FAILED! >>>>>> ERASE FAILED! >>>>>> FAILED! >>>>>> Your flash chip is in an unknown state. >>>>>> Get help on IRC at irc.freenode.net (channel #flashrom) or >>>>>> mail flashrom(a)flashrom.org! >>>>>> ------------------------------------------------------------------------------- >>>>>> DO NOT REBOOT OR POWEROFF! >>>>> >>>>> Can you re-run flashrom like above, but with the "-V" (--verbose) parameter ? >>>>> Like this: sudo flashrom -V -w 88GAP804.BST >>>>> >>>>>> sudo flashrom -w 88GAP804.BST 8.37s user 0.07s system 99% cpu 8.489 total >>>>>> >>>>>> ============================================================== >>>>>> >>>>>> So, since the erase failed, shouldn't I be okay? Unless my cats press >>>>>> a button or pull a wire, I will leave the machine on for a response. >>>>>> >>>>>> Thank you very much for your help in advance! >>>>>> >>>>>> ----- bernard >>>>>> >>>>>> _______________________________________________ >>>>>> flashrom mailing list >>>>>> flashrom(a)flashrom.org >>>>>> http://www.flashrom.org/mailman/listinfo/flashrom >>>>>> >>>>> >>>> >>> >> >

1 0

Re: [flashrom] HELP! "...flash chip is in an unknown state"
by Idwer Vollering 12 Apr '11

12 Apr '11

2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: > Since I know it will work now, I will be happy to try and reflash it > per your instructions so we can see what is happening. > > Give me several minutes, and I will email the output to you. > > Thank you again! Please use "reply to all", thanks. Idwer > > ----- bernard > > On Tue, Apr 12, 2011 at 5:44 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>> Thank you very, very much for getting in touch with me! >>> >>> I solved the problem before I got your email, but didn't have a chance >>> to email an update yet. >>> >>> On my system, it appears flashrom cannot be run from an Xterm window. >>> If that is in the documentation somewhere, I apologize for missing it. >> >> No, it's not. This sounds weird. >> >>> >>> I first verified with "flashrom -v 88GAP901_BST_20110411.BST" that >>> the image currently in the rom matched my backup file, in case I had >>> to reboot. >>> >>> I cannot recall if I did reboot first, or if I had just closed X windows. >>> >>> Using flashrom from a text terminal CLI worked perfectly! I see the >>> new file and date on my boot screen now, and so far no problems. >>> >>> Thank you folks very much for such a wonderful program. >>> >>> ----- bernard >>> >>> On Tue, Apr 12, 2011 at 2:16 PM, Idwer Vollering <vidwer(a)gmail.com> wrote: >>>> 2011/4/12 Bernard Matthews <philoscience(a)gmail.com>: >>>>> Hi Help, >>>>> >>>>> I thought I did what was right, but apparently I'm missing something. >>>>> >>>>> System details: >>>>> >>>>> BioStar TA785G3 v 6.1 according to the printing on the mainboard. >>>>> >>>>> Athlon II X3 435. >>>>> >>>>> Label on factory CMOS: 88GAP901BST. But the date showing on boot is 3/31/2010. >>>>> >>>>> I'm trying to replace the CMOS info because of an intermittent board >>>>> failure that I felt I had reduced to either a processor failure or a >>>>> board failure. >>>>> >>>>> The mainboard comes with a built-in utility on F12 to flash the new >>>>> file, but it rejects the file claiming that the BIOS ID does not >>>>> match. >>>>> >>>>> The new file came from Biostar. I actually downloaded two copies, one >>>>> from Taiwan, and one from USA, and diff'd them to make sure they were >>>>> the same. >>>>> >>>>> So below are the results of my attempt to flash the chip :-(. >>>>> >>>>> >>>>> Here's my initial run to check for compatibility with my board (blank >>>>> spaces/lines added for legibility) >>>>> ============================================================== >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> No operations were specified. >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % sudo flashrom -r 88GAP901_BST_20110411.BST >>>> >>>> This is your backup file... >>>> >>>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Reading flash... done. >>>>> >>>>> ============================================================== >>>>> >>>>> At this point, I did a Google search for "Block protection could not >>>>> be disabled", but did not find anything that said THIS MEANS YOU WON'T >>>>> BE ABLE TO ERASE! >>>>> >>>>> So, I forged ahead: >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista % ls -l *BST >>>>> >>>>> -r--r--r-- 1 root root 1048576 2011-04-12 05:57 88GAP901_BST_20110411.BST >>>>> grml@grml /mnt/2011_home/netvista % cd Down* >>>>> >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % ls -l *BST >>>>> >>>>> -r--r--r-- 1 grml users 1048576 2011-04-10 07:43 88GAP804.BST >>>>> >>>>> ============================================================== >>>>> >>>>> The above lines show that the file that I'm going to write with >>>>> (88GAP804.BST) is the same size as the one that I saved from the chip >>>>> (88GAP901_BST_20110411.BST). >>>>> >>>>> ============================================================== >>>>> >>>>> grml@grml /mnt/2011_home/netvista/Downloads % sudo flashrom -w 88GAP804.BST >>>> >>>> and this is the new file. >>>> >>>>> flashrom v0.9.2-r1141 on Linux 2.6.36-grml (i686), built with libpci >>>>> 3.1.7, GCC 4.4.5 20100728 (prerelease), little endian >>>>> flashrom is free software, get the source code at http://www.flashrom.org >>>>> >>>>> Calibrating delay loop... OK. >>>>> No coreboot table found. >>>>> Found ITE Super I/O, id 8718 >>>>> Found chipset "AMD SB700/SB710/SB750", enabling flash write... OK. >>>>> This chipset supports the following protocols: LPC,FWH,SPI. >>>>> Found chip "Macronix MX25L8005" (1024 KB, SPI) at physical address 0xfff00000. >>>>> Block protection could not be disabled! >>>>> Flash image seems to be a legacy BIOS. Disabling checks. >>>>> Writing flash chip... Erasing flash before programming... Erasing flash chip... >>>>> >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x00000fff: 0xf9d >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x0000ffff: 0xf8fa >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> ERASE FAILED at 0x0000000c! Expected=0xff, Read=0xec, failed byte >>>>> count from 0x00000000-0x000fffff: 0xdc5ed >>>>> ERASE FAILED! >>>>> FAILED! >>>>> ERASE FAILED! >>>>> FAILED! >>>>> Your flash chip is in an unknown state. >>>>> Get help on IRC at irc.freenode.net (channel #flashrom) or >>>>> mail flashrom(a)flashrom.org! >>>>> ------------------------------------------------------------------------------- >>>>> DO NOT REBOOT OR POWEROFF! >>>> >>>> Can you re-run flashrom like above, but with the "-V" (--verbose) parameter ? >>>> Like this: sudo flashrom -V -w 88GAP804.BST >>>> >>>>> sudo flashrom -w 88GAP804.BST 8.37s user 0.07s system 99% cpu 8.489 total >>>>> >>>>> ============================================================== >>>>> >>>>> So, since the erase failed, shouldn't I be okay? Unless my cats press >>>>> a button or pull a wire, I will leave the machine on for a response. >>>>> >>>>> Thank you very much for your help in advance! >>>>> >>>>> ----- bernard >>>>> >>>>> _______________________________________________ >>>>> flashrom mailing list >>>>> flashrom(a)flashrom.org >>>>> http://www.flashrom.org/mailman/listinfo/flashrom >>>>> >>>> >>> >> >

1 0

[PATCH] explain better what checks are disabled in case we detect a legacy BIOS
by Stefan Tauner 12 Apr '11

12 Apr '11

Signed-off-by: Stefan Tauner <stefan.tauner(a)student.tuwien.ac.at> --- layout.c | 3 ++- 1 files changed, 2 insertions(+), 1 deletions(-) diff --git a/layout.c b/layout.c index 92fe852..d719a05 100644 --- a/layout.c +++ b/layout.c @@ -76,7 +76,8 @@ int show_id(uint8_t *bios, int size, int force) mb_vendor_offset = *(walk - 2); if ((*walk) == 0 || ((*walk) & 0x3ff) != 0 || (*walk) > size || mb_part_offset > size || mb_vendor_offset > size) { - msg_pinfo("Flash image seems to be a legacy BIOS. Disabling checks.\n"); + msg_pinfo("Flash image seems to be a legacy BIOS. " + "Disabling coreboot-related checks.\n"); return 0; } -- 1.7.1

1 0

← Newer
1
...
13
14
15
16
17
18
19
20
21
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

flashrom April 2011