Hi, I could not use flashrom 0.9.3 -r1205 to detect Winbond W25Q128 to program BIOS. Attached the read log
Just by adding WINBOND_NEX_W25Q128 0x4018 in flashchips.c for W25Q128, similar to W25Q64 throws run Opcode 0x3 error for read.
Could you please give some suggestions.
-Antony
# ./flashrom -Vr ./read.bios flashrom v0.9.3-r1205 on NetBSD 5.1_STABLE (i386), built with libpci 3.1.3, GCC 4.1.3 20080704 prerelease (NetBSD nb2 20081120), little endian flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OS timer resolution is 1 usecs, 153M loops per second, 10 myus = 10 us, 100 myus = 102 us, 1000 myus = 1026 us, 10000 myus = 10213 us, 4 myus = 5 us, OK. Initializing internal programmer No coreboot table found. sh: dmidecode: not found dmidecode execution unsucessfull - continuing without DMI info Found chipset "Intel 3420", enabling flash write... chipset PCI ID is 8086:3b14, 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x0 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x1 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x2 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x3 0x7fffffff/0x7fffffff FWH IDSEL: 0x4 0x7fffffff/0x7fffffff FWH IDSEL: 0x5 0x7fffffff/0x7fffffff FWH IDSEL: 0x6 0x7fffffff/0x7fffffff FWH IDSEL: 0x7 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode enabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled 0x7fffffff/0x7fffffff FWH decode disabled Maximum FWH chip size: 0x100000 bytes BIOS Lock Enable: disabled, BIOS Write Enable: disabled, BIOS_CNTL is 0x8
Root Complex Register Block address = 0xfed1c000 GCS = 0xc40: BIOS Interface Lock-Down: disabled, BOOT BIOS Straps: 0x3 (LPC) Top Swap : not enabled SPIBAR = 0xfed1c000 + 0x3800 0x04: 0x6008 (HSFS) FLOCKDN 0, FDV 1, FDOPSS 1, SCIP 0, BERASE 1, AEL 0, FCERR 0, FDONE 0 0x50: 0x0000ffff (FRAP) BMWAG 0x00, BMRAG 0x00, BRWA 0xff, BRRA 0xff 0x54: 0x00000000 (FREG0: Flash Descriptor) 0x00000000-0x00000fff is read-write 0x58: 0x07ff0400 (FREG1: BIOS) 0x00400000-0x007fffff is read-write 0x5C: 0x03ff0003 (FREG2: Management Engine) 0x00003000-0x003fffff is read-write 0x60: 0x00020001 (FREG3: Gigabit Ethernet) 0x00001000-0x00002fff is read-write 0x64: 0x00000fff (FREG4: Platform Data) 0x00fff000-0x00000fff is read-write 0x74: 0x00000000 (PR0) 0x78: 0x00000000 (PR1) 0x7C: 0x00000000 (PR2) 0x80: 0x00000000 (PR3) 0x84: 0x00000000 (PR4) 0x90: 0xf8414004 (SSFS, SSFC) 0x94: 0x5006 (PREOP) 0x96: 0x462b (OPTYPE) 0x98: 0x05ab0302 (OPMENU) 0x9C: 0xc79f0190 (OPMENU+4) 0xA0: 0x00000000 (BBAR) 0xB0: 0x00001000 (FDOC) Programming OPCODES... program_opcodes: preop=5006 optype=463b opmenu=05d80302c79f0190 done SPI Read Configuration: prefetching enabled, caching enabled, OK. This chipset supports the following protocols: FWH,SPI. Probing for AMD Am29F010A/B, 128 KB: skipped. Probing for AMD Am29F002(N)BB, 256 KB: skipped. Probing for AMD Am29F002(N)BT, 256 KB: skipped. Probing for AMD Am29F016D, 2048 KB: skipped. Probing for AMD Am29F040B, 512 KB: skipped. Probing for AMD Am29F080B, 1024 KB: skipped. Probing for AMD Am29LV040B, 512 KB: skipped. Probing for AMD Am29LV081B, 1024 KB: skipped. Probing for AMIC A25L05PT, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L05PU, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L10PT, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L10PU, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L20PT, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L20PU, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L40PT, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L40PU, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L80P, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L16PT, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L16PU, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L512, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L010, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L020, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L040, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L080, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L016, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25L032, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A25LQ032, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for AMIC A29002B, 256 KB: skipped. Probing for AMIC A29002T, 256 KB: skipped. Probing for AMIC A29040B, 512 KB: skipped. Probing for AMIC A49LF040A, 512 KB: skipped. Probing for Atmel AT25DF021, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF041A, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF081, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF161, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF321, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF321A, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DF641, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25DQ161, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25F512B, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25FS010, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT25FS040, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF041, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF081A, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF161, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26DF161A, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT26F004, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT29C512, 64 KB: skipped. Probing for Atmel AT29C010A, 128 KB: skipped. Probing for Atmel AT29C020, 256 KB: skipped. Probing for Atmel AT29C040A, 512 KB: skipped. Probing for Atmel AT45CS1282, 16896 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB011D, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB021D, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB041D, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB081D, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB161D, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB321C, 4224 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB321D, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT45DB642D, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel AT49BV512, 64 KB: skipped. Probing for Atmel AT49F020, 256 KB: skipped. Probing for Atmel AT49F002(N), 256 KB: skipped. Probing for Atmel AT49F002(N)T, 256 KB: skipped. Probing for Bright BM29F040, 512 KB: skipped. Probing for EMST F49B002UA, 256 KB: skipped. Probing for EMST F25L008A, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B05, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B05T, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B10, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B10T, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B20, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B20T, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B40, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B40T, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B80, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B80T, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B16, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B16T, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B32, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B32T, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B64, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25B64T, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25D16, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F05, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F10, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F20, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F40, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F80, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F16, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN25F32, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon EN29F010, 128 KB: skipped. Probing for Eon EN29F002(A)(N)B, 256 KB: skipped. Probing for Eon EN29F002(A)(N)T, 256 KB: skipped. Probing for Fujitsu MBM29F004BC, 512 KB: skipped. Probing for Fujitsu MBM29F004TC, 512 KB: skipped. Probing for Fujitsu MBM29F400BC, 512 KB: skipped. Probing for Fujitsu MBM29F400TC, 512 KB: skipped. Probing for Hyundai HY29F002T, 256 KB: skipped. Probing for Hyundai HY29F002B, 256 KB: skipped. Probing for Hyundai HY29F040A, 512 KB: skipped. Probing for Intel 28F001BN/BX-B, 128 KB: skipped. Probing for Intel 28F001BN/BX-T, 128 KB: skipped. Probing for Intel 28F002BC/BL/BV/BX-T, 256 KB: skipped. Probing for Intel 28F008S3/S5/SC, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-B, 512 KB: skipped. Probing for Intel 28F004B5/BE/BV/BX-T, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-B, 512 KB: skipped. Probing for Intel 28F400BV/BX/CE/CV-T, 512 KB: skipped. Probing for Intel 82802AB, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Intel 82802AC, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Macronix MX25L512, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1005, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L2005, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L4005, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L8005, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1605, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1635D, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L1635E, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3205, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L3235D, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L6405, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX25L12805, 16384 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix MX29F001B, 128 KB: skipped. Probing for Macronix MX29F001T, 128 KB: skipped. Probing for Macronix MX29F002B, 256 KB: skipped. Probing for Macronix MX29F002T, 256 KB: skipped. Probing for Macronix MX29F040, 512 KB: skipped. Probing for Macronix MX29LV040, 512 KB: skipped. Probing for MoselVitelic V29C51000B, 64 KB: skipped. Probing for MoselVitelic V29C51000T, 64 KB: skipped. Probing for MoselVitelic V29C51400B, 512 KB: skipped. Probing for MoselVitelic V29C51400T, 512 KB: skipped. Probing for MoselVitelic V29LC51000, 64 KB: skipped. Probing for MoselVitelic V29LC51001, 128 KB: skipped. Probing for MoselVitelic V29LC51002, 256 KB: skipped. Probing for Numonyx M25PE10, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE20, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE40, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE80, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Numonyx M25PE16, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV010, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV016B, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV020, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV040, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV080B, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm25LV512, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC Pm29F002T, 256 KB: skipped. Probing for PMC Pm29F002B, 256 KB: skipped. Probing for PMC Pm39LV010, 128 KB: skipped. Probing for PMC Pm39LV020, 256 KB: skipped. Probing for PMC Pm39LV040, 512 KB: skipped. Probing for PMC Pm49FL002, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for PMC Pm49FL004, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Sanyo LF25FW203A, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sharp LHF00L04, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Spansion S25FL004A, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL008A, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL016A, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL032A, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Spansion S25FL064A, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF010.REMS, 128 KB: probe_spi_rems: id1 0xef, id2 0x17 Probing for SST SST25VF016B, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF032B, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF064C, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25VF040.REMS, 512 KB: probe_spi_rems: id1 0xef, id2 0x17 Probing for SST SST25VF040B, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST25LF040A.RES, 512 KB: program_opcodes: preop=5006 optype=462b opmenu=05ab0302c79f0190 on-the-fly OPCODE (0xAB) re-programmed, op-pos=2 probe_spi_res2: id1 0x17, id2 0x17 Probing for SST SST25VF040B.REMS, 512 KB: probe_spi_rems: id1 0xef, id2 0x17 Probing for SST SST25VF080B, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST SST28SF040A, 512 KB: skipped. Probing for SST SST29EE010, 128 KB: skipped. Probing for SST SST29LE010, 128 KB: skipped. Probing for SST SST29EE020A, 256 KB: skipped. Probing for SST SST29LE020, 256 KB: skipped. Probing for SST SST39SF512, 64 KB: skipped. Probing for SST SST39SF010A, 128 KB: skipped. Probing for SST SST39SF020A, 256 KB: skipped. Probing for SST SST39SF040, 512 KB: skipped. Probing for SST SST39VF512, 64 KB: skipped. Probing for SST SST39VF010, 128 KB: skipped. Probing for SST SST39VF020, 256 KB: skipped. Probing for SST SST39VF040, 512 KB: skipped. Probing for SST SST39VF080, 1024 KB: skipped. Probing for SST SST49LF002A/B, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF003A/B, 384 KB: probe_jedec_common: id1 0x4e, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004A/B, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF004C, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008A, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF008C, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF016C, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for SST SST49LF020, 256 KB: skipped. Probing for SST SST49LF020A, 256 KB: skipped. Probing for SST SST49LF040, 512 KB: skipped. Probing for SST SST49LF040B, 512 KB: skipped. Probing for SST SST49LF080A, 1024 KB: skipped. Probing for SST SST49LF160C, 2048 KB: skipped. Probing for ST M25P05-A, 64 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P05.RES, 64 KB: Ignoring RES in favour of RDID. Probing for ST M25P10-A, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P10.RES, 128 KB: Ignoring RES in favour of RDID. Probing for ST M25P20, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P40, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P40-old, 512 KB: Ignoring RES in favour of RDID. Probing for ST M25P80, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P16, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P32, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P64, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25P128, 16384 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25PX32, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M25PX64, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST M29F002B, 256 KB: skipped. Probing for ST M29F002T/NT, 256 KB: skipped. Probing for ST M29F040B, 512 KB: skipped. Probing for ST M29F400BB, 512 KB: skipped. Probing for ST M29F400BT, 512 KB: skipped. Probing for ST M29W010B, 128 KB: skipped. Probing for ST M29W040B, 512 KB: skipped. Probing for ST M29W512B, 64 KB: skipped. Probing for ST M50FLW040A, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW040B, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080A, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FLW080B, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW002, 256 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW016, 2048 KB: Chip size 2048 kB is bigger than supported size 1024 kB of chipset/board/programmer for FWH interface, probe/read/erase/write may fail. probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW040, 512 KB: probe_82802ab: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for ST M50FW080, 1024 KB: probe_82802ab: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for ST M50LPW116, 2048 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001B, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51001T, 128 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002B, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51002T, 256 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {F,S,V}29C51004T, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004B, 512 KB: skipped. Probing for SyncMOS/MoselVitelic {S,V}29C31004T, 512 KB: skipped. Probing for TI TMS29F002RB, 256 KB: skipped. Probing for TI TMS29F002RT, 256 KB: skipped. Probing for Winbond W25Q80, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q16, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q32, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25Q64, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25x10, 128 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25x20, 256 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25x40, 512 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25x80, 1024 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25x16, 2048 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25x32, 4096 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W25x64, 8192 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W29C020(C)/W29C022, 256 KB: skipped. Probing for Winbond W29C040/P, 512 KB: skipped. Probing for Winbond W29C010(M)/W29C011A/W29EE011/W29EE012, 128 KB: skipped. Probing for Winbond W39V040A, 512 KB: skipped. Probing for Winbond W39V040B, 512 KB: skipped. Probing for Winbond W39V040C, 512 KB: skipped. Probing for Winbond W39V040FA, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FB, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V040FC, 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080A, 1024 KB: skipped. Probing for Winbond W49F002U/N, 256 KB: skipped. Probing for Winbond W49F020, 256 KB: skipped. Probing for Winbond W49V002A, 256 KB: skipped. Probing for Winbond W49V002FA, 256 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA, 1024 KB: probe_jedec_common: id1 0xff, id2 0xff, id1 parity violation, id1 is normal flash content, id2 is normal flash content Probing for Winbond W39V080FA (dual mode), 512 KB: probe_jedec_common: id1 0xea, id2 0xd0, id1 is normal flash content, id2 is normal flash content Probing for AMIC unknown AMIC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Atmel unknown Atmel SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Eon unknown Eon SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Macronix unknown Macronix SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for PMC unknown PMC SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for SST unknown SST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for ST unknown ST SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Sanyo unknown Sanyo SPI chip, 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Probing for Generic unknown SPI chip (RDID), 0 KB: probe_spi_rdid_generic: id1 0xef, id2 0x4018 Found chip "Generic unknown SPI chip (RDID)" (0 KB, SPI) at physical address 0x0. Probing for Generic unknown SPI chip (REMS), 0 KB: probe_spi_rems: id1 0xef, id2 0x17 === This flash part has status NOT WORKING for operations: PROBE READ ERASE WRITE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Read is not working on this chip. Aborting. Restoring PCI config space for 00:1f:0 reg 0xdc
On Wed, 27 Apr 2011 18:25:07 -0700 Rheneus rheneus.paul@gmail.com wrote:
Hi, I could not use flashrom 0.9.3 -r1205 to detect Winbond W25Q128 to program BIOS. Attached the read log
Just by adding WINBOND_NEX_W25Q128 0x4018 in flashchips.c for W25Q128, similar to W25Q64 throws run Opcode 0x3 error for read.
Could you please give some suggestions.
hello
please show us the code you have added (if you also checked the datasheet of the W25Q128 to match that code, please submit it as patch already http://www.coreboot.org/Development_Guidelines#How_to_contribute). and please show us the log of the failed read with the W25Q128 added. thanks
I didn't go thru data sheet, I have have just inserted the size and the enum as in the added patch w25Q128.patch.
The verbose output of read is attached in flashrom_notworking.txt.
The below is the error log without verbose. flashrom is free software, get the source code at http://www.flashrom.org
Calibrating delay loop... OK. No coreboot table found. Found chipset "Intel", enabling flash write... OK. This chipset supports the following protocols: FWH,SPI. Found chip "Winbond W25Q128" (16384 KB, SPI) at physical address 0xff000000. === This flash part has status UNTESTED for operations: ERASE The test status of this chip may have been updated in the latest development version of flashrom. If you are running the latest development version, please email a report to flashrom@flashrom.org if any of the above operations work correctly for you with this flash part. Please include the flashrom output with the additional -V option for all operations you tested (-V, -Vr, -Vw, -VE), and mention which mainboard or programmer you tested. Please mention your board in the subject line. Thanks for your help! Reading flash... Read operation failed! FAILED.
On Fri, Apr 29, 2011 at 1:42 AM, Stefan Tauner < stefan.tauner@student.tuwien.ac.at> wrote:
On Wed, 27 Apr 2011 18:25:07 -0700 Rheneus rheneus.paul@gmail.com wrote:
Hi, I could not use flashrom 0.9.3 -r1205 to detect Winbond W25Q128 to program BIOS. Attached the read log
Just by adding WINBOND_NEX_W25Q128 0x4018 in flashchips.c for W25Q128, similar to W25Q64 throws run Opcode 0x3 error for read.
Could you please give some suggestions.
hello
please show us the code you have added (if you also checked the datasheet of the W25Q128 to match that code, please submit it as patch already http://www.coreboot.org/Development_Guidelines#How_to_contribute). and please show us the log of the failed read with the W25Q128 added. thanks
-- Kind regards/Mit freundlichen Grüßen, Stefan Tauner
On Fri, 29 Apr 2011 08:08:58 -0700 Rheneus rheneus.paul@gmail.com wrote:
I didn't go thru data sheet, I have have just inserted the size and the enum as in the added patch w25Q128.patch.
hello!
sorry for the long response time. i have reviewed the patch you supplied and it seems to be correct and consistent with the data sheet. it does no longer apply to the current version of the source but i have applied it manually. if possible please provide a signed-off line as described at http://www.coreboot.org/Development_Guidelines#Sign-off_Procedure so that i can formally accept the patch and commit it to our source repository, thanks!
The verbose output of read is attached in flashrom_notworking.txt.
it is not clear to me what went wrong there. the enabling of your chipset works. it is not locked down and all regions are in read/write mode. you are using the latest stable version which is a bit old already and maybe that's the culprit. could you please try a current version from the source repository as described at http://www.flashrom.org/Downloads and reply with the output of './flashrom -VVr testfile.rom'? we have also added more detailed error messages which may help to debug this problem in case it is not solved already.
Support for Winbond W25Q128 (16384 KB, SPI)
Signed-off-by: Antony rheneus.paul@gmail.com
---
On Sat, May 21, 2011 at 3:55 AM, Stefan Tauner < stefan.tauner@student.tuwien.ac.at> wrote:
On Fri, 29 Apr 2011 08:08:58 -0700 Rheneus rheneus.paul@gmail.com wrote:
I didn't go thru data sheet, I have have just inserted the size and the
enum
as in the added patch w25Q128.patch.
hello!
sorry for the long response time. i have reviewed the patch you supplied and it seems to be correct and consistent with the data sheet. it does no longer apply to the current version of the source but i have applied it manually. if possible please provide a signed-off line as described at http://www.coreboot.org/Development_Guidelines#Sign-off_Procedure so that i can formally accept the patch and commit it to our source repository, thanks!
The verbose output of read is attached in flashrom_notworking.txt.
it is not clear to me what went wrong there. the enabling of your chipset works. it is not locked down and all regions are in read/write mode. you are using the latest stable version which is a bit old already and maybe that's the culprit. could you please try a current version from the source repository as described at http://www.flashrom.org/Downloads and reply with the output of './flashrom -VVr testfile.rom'? we have also added more detailed error messages which may help to debug this problem in case it is not solved already. -- Kind regards/Mit freundlichen Grüßen, Stefan Tauner
2011/5/22 Rheneus rheneus.paul@gmail.com:
Support for Winbond W25Q128 (16384 KB, SPI)
Signed-off-by: Antony rheneus.paul@gmail.com
--- ../flashrom-0.9.3/flashchips.c 2010-10-05 15:29:08.000000000 -0700 +++ flashrom-0.9.3/flashchips.c 2011-04-27 17:33:47.048318000 -0700
To ease integration, can you resend your patch based on the latest development code? http://www.flashrom.org/Downloads#Installation_from_source
.tested = TEST_OK_PRW,
Have you tried to erase this chip as well and how did that work out? If erase works, please change TEST_OK_PRW to TEST_OK_PREW.
Thanks,
Idwer
On Sun, 22 May 2011 00:50:35 +0200 Idwer Vollering vidwer@gmail.com wrote:
2011/5/22 Rheneus rheneus.paul@gmail.com:
Support for Winbond W25Q128 (16384 KB, SPI)
Signed-off-by: Antony rheneus.paul@gmail.com
sorry, this is not sufficient. we need your full real name in the signed off line to include you as the author.
To ease integration, can you resend your patch based on the latest development code? http://www.flashrom.org/Downloads#Installation_from_source
not necessary imho. i have it already integrated in my local HEAD (and its a small change that does not need to/can not be tested, so there is no real use of having it posted).
.tested = TEST_OK_PRW,Have you tried to erase this chip as well and how did that work out? If erase works, please change TEST_OK_PRW to TEST_OK_PREW.
the .tested field in his patch is bogus. its probably a left over from his copy&paste action. look at the -Vr log he provided in his mail from 2011-04-29. read fails (btw i would like to hear suggestions what the cause might be :). i have set .tested to TEST_OK_PROBE.
Signed-off-by: Antony Rheneus rheneus.paul@gmail.com
---
On Sat, May 21, 2011 at 9:35 PM, Stefan Tauner < stefan.tauner@student.tuwien.ac.at> wrote:
On Sun, 22 May 2011 00:50:35 +0200 Idwer Vollering vidwer@gmail.com wrote:
2011/5/22 Rheneus rheneus.paul@gmail.com:
Support for Winbond W25Q128 (16384 KB, SPI)
Signed-off-by: Antony rheneus.paul@gmail.com
sorry, this is not sufficient. we need your full real name in the signed off line to include you as the author.
To ease integration, can you resend your patch based on the latest development code? http://www.flashrom.org/Downloads#Installation_from_source
not necessary imho. i have it already integrated in my local HEAD (and its a small change that does not need to/can not be tested, so there is no real use of having it posted).
.tested = TEST_OK_PRW,Have you tried to erase this chip as well and how did that work out? If erase works, please change TEST_OK_PRW to TEST_OK_PREW.
the .tested field in his patch is bogus. its probably a left over from his copy&paste action. look at the -Vr log he provided in his mail from 2011-04-29. read fails (btw i would like to hear suggestions what the cause might be :). i have set .tested to TEST_OK_PROBE.
-- Kind regards/Mit freundlichen Grüßen, Stefan Tauner
-
Idwer Vollering -
Rheneus -
Stefan Tauner